Guest User

Untitled

a guest
May 29th, 2016
78
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. sudo smartctl -a /dev/sda
  2. smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-21-generic] (local build)
  3. Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
  4.  
  5. === START OF INFORMATION SECTION ===
  6. Model Family: JMicron based SSDs
  7. Device Model: KINGSTON SNV425S264GB
  8. Serial Number: 07TA60028524
  9. Firmware Version: D100309a
  10. User Capacity: 64,023,257,088 bytes [64.0 GB]
  11. Sector Size: 512 bytes logical/physical
  12. Rotation Rate: Solid State Device
  13. Form Factor: 2.5 inches
  14. Device is: In smartctl database [for details use: -P show]
  15. ATA Version is: ATA8-ACS (minor revision not indicated)
  16. SATA Version is: SATA 2.6, 3.0 Gb/s
  17. Local Time is: Sun May 29 17:34:27 2016 UTC
  18. SMART support is: Available - device has SMART capability.
  19. SMART support is: Enabled
  20.  
  21. === START OF READ SMART DATA SECTION ===
  22. SMART overall-health self-assessment test result: PASSED
  23.  
  24. General SMART Values:
  25. Offline data collection status: (0x00) Offline data collection activity
  26. was never started.
  27. Auto Offline Data Collection: Disabled.
  28. Self-test execution status: ( 0) The previous self-test routine completed
  29. without error or no self-test has ever
  30. been run.
  31. Total time to complete Offline
  32. data collection: ( 30) seconds.
  33. Offline data collection
  34. capabilities: (0x1b) SMART execute Offline immediate.
  35. Auto Offline data collection on/off support.
  36. Suspend Offline collection upon new
  37. command.
  38. Offline surface scan supported.
  39. Self-test supported.
  40. No Conveyance Self-test supported.
  41. No Selective Self-test supported.
  42. SMART capabilities: (0x0003) Saves SMART data before entering
  43. power-saving mode.
  44. Supports SMART auto save timer.
  45. Error logging capability: (0x01) Error logging supported.
  46. General Purpose Logging supported.
  47. Short self-test routine
  48. recommended polling time: ( 1) minutes.
  49. Extended self-test routine
  50. recommended polling time: ( 1) minutes.
  51.  
  52. SMART Attributes Data Structure revision number: 16
  53. Vendor Specific SMART Attributes with Thresholds:
  54. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  55. 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
  56. 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
  57. 3 Unknown_JMF_Attribute 0x0007 100 100 050 Pre-fail Always - 0
  58. 5 Reallocated_Sector_Ct 0x0013 100 100 050 Pre-fail Always - 0
  59. 7 Unknown_JMF_Attribute 0x000b 100 100 050 Pre-fail Always - 0
  60. 8 Unknown_JMF_Attribute 0x0005 100 100 050 Pre-fail Offline - 0
  61. 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 26038
  62. 10 Unknown_JMF_Attribute 0x0013 100 100 050 Pre-fail Always - 0
  63. 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 2288
  64. 168 SATA_Phy_Error_Count 0x0012 100 100 000 Old_age Always - 7
  65. 175 Bad_Cluster_Table_Count 0x0003 100 100 010 Pre-fail Always - 4
  66. 192 Unexpect_Power_Loss_Ct 0x0012 100 100 000 Old_age Always - 0
  67. 194 Temperature_Celsius 0x0022 037 100 020 Old_age Always - 37 (Min/Max 34/40)
  68. 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
  69. 240 Unknown_JMF_Attribute 0x0013 100 100 050 Pre-fail Always - 0
  70. 170 Bad_Block_Count 0x0003 100 100 010 Pre-fail Always - 131 241 117
  71. 173 Erase_Count 0x0012 100 100 000 Old_age Always - 23215 30835 25964
  72.  
  73. SMART Error Log Version: 1
  74. ATA Error Count: 16 (device log contains only the most recent five errors)
  75. CR = Command Register [HEX]
  76. FR = Features Register [HEX]
  77. SC = Sector Count Register [HEX]
  78. SN = Sector Number Register [HEX]
  79. CL = Cylinder Low Register [HEX]
  80. CH = Cylinder High Register [HEX]
  81. DH = Device/Head Register [HEX]
  82. DC = Device Command Register [HEX]
  83. ER = Error register [HEX]
  84. ST = Status register [HEX]
  85. Powered_Up_Time is measured from power on, and printed as
  86. DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
  87. SS=sec, and sss=millisec. It "wraps" after 49.710 days.
  88.  
  89. Error 16 occurred at disk power-on lifetime: 26036 hours (1084 days + 20 hours)
  90. When the command that caused the error occurred, the device was active or idle.
  91.  
  92. After command completion occurred, registers were:
  93. ER ST SC SN CL CH DH
  94. -- -- -- -- -- -- --
  95. 40 51 00 48 13 8b e0 Error: UNC at LBA = 0x008b1348 = 9114440
  96.  
  97. Commands leading to the command that caused the error were:
  98. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  99. -- -- -- -- -- -- -- -- ---------------- --------------------
  100. c8 00 08 48 13 8b e0 08 03:16:14.900 READ DMA
  101. c8 00 08 40 13 8b e0 08 03:16:14.900 READ DMA
  102. c8 00 08 38 13 8b e0 08 03:16:14.900 READ DMA
  103. c8 00 08 30 13 8b e0 08 03:16:14.900 READ DMA
  104. c8 00 08 28 13 8b e0 08 03:16:14.900 READ DMA
  105.  
  106. Error 15 occurred at disk power-on lifetime: 26036 hours (1084 days + 20 hours)
  107. When the command that caused the error occurred, the device was active or idle.
  108.  
  109. After command completion occurred, registers were:
  110. ER ST SC SN CL CH DH
  111. -- -- -- -- -- -- --
  112. 40 51 00 48 13 8b e0 Error: UNC at LBA = 0x008b1348 = 9114440
  113.  
  114. Commands leading to the command that caused the error were:
  115. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  116. -- -- -- -- -- -- -- -- ---------------- --------------------
  117. c8 00 08 48 13 8b e0 08 03:07:11.400 READ DMA
  118. c8 00 08 40 13 8b e0 08 03:07:11.400 READ DMA
  119. c8 00 08 38 13 8b e0 08 03:07:11.400 READ DMA
  120. c8 00 08 30 13 8b e0 08 03:07:11.400 READ DMA
  121. c8 00 08 28 13 8b e0 08 03:07:11.400 READ DMA
  122.  
  123. Error 14 occurred at disk power-on lifetime: 26036 hours (1084 days + 20 hours)
  124. When the command that caused the error occurred, the device was active or idle.
  125.  
  126. After command completion occurred, registers were:
  127. ER ST SC SN CL CH DH
  128. -- -- -- -- -- -- --
  129. 40 51 00 48 13 8b e0 Error: UNC at LBA = 0x008b1348 = 9114440
  130.  
  131. Commands leading to the command that caused the error were:
  132. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  133. -- -- -- -- -- -- -- -- ---------------- --------------------
  134. c8 00 08 48 13 8b e0 08 03:01:10.500 READ DMA
  135. c8 00 08 40 13 8b e0 08 03:01:10.500 READ DMA
  136. c8 00 08 38 13 8b e0 08 03:01:10.500 READ DMA
  137. c8 00 08 30 13 8b e0 08 03:01:10.500 READ DMA
  138. c8 00 08 28 13 8b e0 08 03:01:10.500 READ DMA
  139.  
  140. Error 13 occurred at disk power-on lifetime: 26036 hours (1084 days + 20 hours)
  141. When the command that caused the error occurred, the device was active or idle.
  142.  
  143. After command completion occurred, registers were:
  144. ER ST SC SN CL CH DH
  145. -- -- -- -- -- -- --
  146. 40 51 00 e0 12 8b e0 Error: UNC at LBA = 0x008b12e0 = 9114336
  147.  
  148. Commands leading to the command that caused the error were:
  149. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  150. -- -- -- -- -- -- -- -- ---------------- --------------------
  151. c8 00 00 e0 12 8b e0 08 03:01:10.500 READ DMA
  152. c8 00 00 e0 11 8b e0 08 03:01:10.500 READ DMA
  153. c8 00 00 e0 10 8b e0 08 03:01:10.500 READ DMA
  154. c8 00 00 e0 0f 8b e0 08 03:01:10.500 READ DMA
  155. c8 00 00 e0 0e 8b e0 08 03:01:10.500 READ DMA
  156.  
  157. Error 12 occurred at disk power-on lifetime: 24813 hours (1033 days + 21 hours)
  158. When the command that caused the error occurred, the device was active or idle.
  159.  
  160. After command completion occurred, registers were:
  161. ER ST SC SN CL CH DH
  162. -- -- -- -- -- -- --
  163. 40 51 00 28 b2 74 e4 Error: UNC at LBA = 0x0474b228 = 74756648
  164.  
  165. Commands leading to the command that caused the error were:
  166. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  167. -- -- -- -- -- -- -- -- ---------------- --------------------
  168. c8 00 18 28 b2 74 e4 00 05:46:36.800 READ DMA
  169. c8 00 18 28 b2 74 e4 00 05:46:36.800 READ DMA
  170. c8 00 50 a8 b1 74 e4 00 05:46:36.800 READ DMA
  171. c8 00 50 a8 b1 74 e4 00 05:46:36.800 READ DMA
  172. c8 00 50 a8 b1 74 e4 00 05:46:36.800 READ DMA
  173.  
  174. SMART Self-test log structure revision number 1
  175. No self-tests have been logged. [To run self-tests, use: smartctl -t]
  176.  
  177. Selective Self-tests/Logging not supported
RAW Paste Data