SHARE
TWEET

Carambola2 reboot-loop when the Ap signal is lost, in STA mo

a guest Jul 14th, 2019 72 in 142 days
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1.  
  2. ########################################################################################################################
  3. ############## First a good boot, with switched on Ap signal.                                ###########################
  4. ############## Then Ap is swotched off, and a manual counter is started to measure seconds   ###########################
  5. ########################################################################################################################
  6.  
  7.  
  8. U-Boot 1.1.4-g682743ef (Jan 20 2016 - 14:54:16)
  9.  
  10. =====================================
  11. Caraboot v2.3 (AR9331) U-boot
  12. http://www.8devices.com/
  13. -------------------------------------
  14. DRAM:  64 MB
  15. Flash: 16 MB
  16. Net:   eth0, eth1
  17. =====================================
  18.  
  19. Hit '<ESC>' key(s) to stop autoboot:  1  0
  20. ## Booting image at 9f050000 ...
  21.    Image Name:   MIPS OpenWrt Linux-4.9.184
  22.    Created:      2019-06-27  12:18:52 UTC
  23.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  24.    Data Size:    1378284 Bytes =  1.3 MB
  25.    Load Address: 80060000
  26.    Entry Point:  80060000
  27.    Verifying Checksum at 0x9f050040 ...OK
  28.    Uncompressing Kernel Image ... OK
  29.  
  30. Starting kernel ...
  31.  
  32. [    0.000000] Linux version 4.9.184 (buildbot@2ccc8102e0c3) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292) ) #0 Thu Jun 27 12:18:52 2019
  33. [    0.000000] bootconsole [early0] enabled
  34. [    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
  35. [    0.000000] SoC: Atheros AR9330 rev 1
  36. [    0.000000] Determined physical RAM map:
  37. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  38. [    0.000000] Initrd not found or empty - disabling initrd
  39. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  40. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  41. [    0.000000] Zone ranges:
  42. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
  43. [    0.000000] Movable zone start for each node
  44. [    0.000000] Early memory node ranges
  45. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
  46. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
  47. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  48. [    0.000000] Kernel command line:  board=CARAMBOLA2 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro console=ttyATH0,115200 rootfstype=squashfs noinitrd
  49. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  50. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  51. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  52. [    0.000000] Writing ErrCtl register=00000000
  53. [    0.000000] Readback ErrCtl register=00000000
  54. [    0.000000] Memory: 59964K/65536K available (3393K kernel code, 178K rwdata, 448K rodata, 324K init, 211K bss, 5572K reserved, 0K cma-reserved)
  55. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  56. [    0.000000] NR_IRQS:51
  57. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
  58. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
  59. [    0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
  60. [    0.007910] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  61. [    0.089133] pid_max: default: 32768 minimum: 301
  62. [    0.093910] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  63. [    0.100354] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  64. [    0.111435] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  65. [    0.119816] futex hash table entries: 256 (order: -1, 3072 bytes)
  66. [    0.127765] NET: Registered protocol family 16
  67. [    0.132855] MIPS: machine is 8devices Carambola2 board
  68. [    0.675988] clocksource: Switched to clocksource MIPS
  69. [    0.681152] NET: Registered protocol family 2
  70. [    0.685404] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  71. [    0.691088] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  72. [    0.697405] TCP: Hash tables configured (established 1024 bind 1024)
  73. [    0.703841] UDP hash table entries: 256 (order: 0, 4096 bytes)
  74. [    0.709572] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  75. [    0.716125] NET: Registered protocol family 1
  76. [    0.725199] Crashlog allocated RAM at address 0x3f00000
  77. [    0.730666] workingset: timestamp_bits=30 max_order=14 bucket_order=0
  78. [    0.746065] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  79. [    0.750436] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  80. [    0.773428] io scheduler noop registered
  81. [    0.775896] io scheduler deadline registered (default)
  82. [    0.781660] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  83. [    0.791343] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a AR933X UART
  84. [    0.799718] console [ttyATH0] enabled
  85. [    0.799718] console [ttyATH0] enabled
  86. [    0.806326] bootconsole [early0] disabled
  87. [    0.806326] bootconsole [early0] disabled
  88. [    0.822605] m25p80 spi0.0: found w25q128, expected m25p80
  89. [    0.837490] m25p80 spi0.0: w25q128 (16384 Kbytes)
  90. [    0.840769] 4 cmdlinepart partitions found on MTD device spi0.0
  91. [    0.846665] Creating 4 MTD partitions on "spi0.0":
  92. [    0.851435] 0x000000000000-0x000000040000 : "u-boot"
  93. [    0.859136] 0x000000040000-0x000000050000 : "u-boot-env"
  94. [    0.865890] 0x000000050000-0x000000ff0000 : "firmware"
  95. [    0.892252] 2 uimage-fw partitions found on MTD device firmware
  96. [    0.896776] 0x000000050000-0x0000001b0000 : "kernel"
  97. [    0.903734] 0x0000001b0000-0x000000ff0000 : "rootfs"
  98. [    0.909702] mtd: device 4 (rootfs) set to be root filesystem
  99. [    0.913951] 1 squashfs-split partitions found on MTD device rootfs
  100. [    0.920170] 0x000000400000-0x000000ff0000 : "rootfs_data"
  101. [    0.928577] 0x000000ff0000-0x000001000000 : "art"
  102. [    0.936267] libphy: Fixed MDIO Bus: probed
  103. [    0.959341] libphy: ag71xx_mdio: probed
  104. [    1.587477] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
  105. [    1.629551] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  106. [    2.257705] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  107. [    2.266451] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  108. [    2.273820] NET: Registered protocol family 10
  109. [    2.282418] NET: Registered protocol family 17
  110. [    2.285475] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  111. [    2.298564] 8021q: 802.1Q VLAN Support v1.8
  112. [    2.304985] hctosys: unable to open rtc device (rtc0)
  113. [    2.315437] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  114. [    2.323607] Freeing unused kernel memory: 324K
  115. [    2.326631] This architecture does not have kernel memory protection.
  116. [    2.556003] random: fast init done
  117. [    3.239242] init: Console is alive
  118. [    3.241483] init: - watchdog -
  119. [    4.514658] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  120. [    4.604431] usbcore: registered new interface driver usbfs
  121. [    4.608665] usbcore: registered new interface driver hub
  122. [    4.613914] usbcore: registered new device driver usb
  123. [    4.626170] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  124. [    4.633407] ehci-platform: EHCI generic platform driver
  125. [    4.637381] ehci-platform ehci-platform: EHCI Host Controller
  126. [    4.642967] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  127. [    4.652974] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  128. [    4.686039] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  129. [    4.692166] hub 1-0:1.0: USB hub found
  130. [    4.695027] hub 1-0:1.0: 1 port detected
  131. [    4.699739] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  132. [    4.716408] init: - preinit -
  133. [    5.749588] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  134. Press the [f] key and hit [enter] to enter failsafe mode
  135. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  136. [    7.387244] eth0: link up (1000Mbps/Full duplex)
  137. [    7.390447] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  138. [    9.127961] jffs2: notice: (398) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  139. [    9.144032] mount_root: switching to jffs2 overlay
  140. [    9.185963] urandom-seed: Seeding with /etc/urandom.seed
  141. [    9.468097] eth0: link down
  142. [    9.485962] procd: - early -
  143. [    9.487649] procd: - watchdog -
  144. [   10.172595] procd: - watchdog -
  145. [   10.174645] procd: - ubus -
  146. [   10.315959] random: ubusd: uninitialized urandom read (4 bytes read)
  147. [   10.390934] random: ubusd: uninitialized urandom read (4 bytes read)
  148. [   10.396569] random: ubusd: uninitialized urandom read (4 bytes read)
  149. [   10.403531] procd: - init -
  150. Please press Enter to activate this console.
  151. [   10.884383] kmodloader: loading kernel modules from /etc/modules.d/*
  152. [   10.896190] ip6_tables: (C) 2000-2006 Netfilter Core Team
  153. [   10.915224] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
  154. [   10.921861] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
  155. [   10.932766] ip_tables: (C) 2000-2006 Netfilter Core Team
  156. [   10.948794] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  157. [   11.032225] xt_time: kernel timezone is -0000
  158. [   11.111877] PPP generic driver version 2.4.2
  159. [   11.118336] NET: Registered protocol family 24
  160. [   11.193710] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  161. [   11.240277] kmodloader: done loading kernel modules from /etc/modules.d/*
  162. [   12.804882] urandom_read: 5 callbacks suppressed
  163. [   12.804894] random: jshn: uninitialized urandom read (4 bytes read)
  164. [   12.924357] random: ubusd: uninitialized urandom read (4 bytes read)
  165. [   26.301043] br-lan: port 1(eth0) entered blocking state
  166. [   26.304825] br-lan: port 1(eth0) entered disabled state
  167. [   26.310667] device eth0 entered promiscuous mode
  168. [   26.366392] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  169. [   26.442622] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  170. [   27.937362] eth0: link up (1000Mbps/Full duplex)
  171. [   27.940598] br-lan: port 1(eth0) entered blocking state
  172. [   27.945749] br-lan: port 1(eth0) entered forwarding state
  173. [   28.047587] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  174. [   29.345216] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  175. [   36.354722] wlan0: authenticate with b0:48:7a:f6:80:aa
  176. [   36.370241] wlan0: send auth to b0:48:7a:f6:80:aa (try 1/3)
  177. [   36.386296] wlan0: authenticated
  178. [   36.406130] wlan0: associate with b0:48:7a:f6:80:aa (try 1/3)
  179. [   36.416348] wlan0: RX AssocResp from b0:48:7a:f6:80:aa (capab=0x431 status=0 aid=3)
  180. [   36.423037] wlan0: associated
  181. [   36.442966] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  182. [  110.636684] random: crng init done
  183.  
  184.  
  185.  
  186. BusyBox v1.28.4 () built-in shell (ash)
  187.  
  188.   _______                     ________        __
  189.  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  190.  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  191.  |_______||   __|_____|__|__||________||__|  |____|
  192.           |__| W I R E L E S S   F R E E D O M
  193.  -----------------------------------------------------
  194.  OpenWrt 18.06.4, r7808-ef686b7292
  195.  -----------------------------------------------------
  196. === WARNING! =====================================
  197. There is no root password defined on this device!
  198. Use the "passwd" command to set up a new password
  199. in order to prevent unauthorized SSH logins.
  200. --------------------------------------------------
  201. root@OpenWrt:/#
  202. root@OpenWrt:/#
  203. root@OpenWrt:/#
  204.  
  205.  
  206. ########################################################################################################################
  207. ############### I started the counter exactly, when I switched off the Ap   ############################################
  208. ########################################################################################################################
  209.  
  210.  
  211.  
  212.  
  213. root@OpenWrt:/#
  214. root@OpenWrt:/#
  215. root@OpenWrt:/#
  216. root@OpenWrt:/# while true ; do i=$((i+1)); echo $i  ; sleep 1 ;done
  217. 1
  218. 2
  219. 3
  220. 4
  221. 5
  222. 6
  223. 7
  224. 8
  225. 9
  226. 10
  227. 11
  228. 12
  229. 13
  230. 14
  231. 15
  232. 16
  233. 17
  234. 18
  235. 19
  236. 20
  237. 21
  238. 22
  239. 23
  240. 24
  241. 25
  242. 26
  243. 27
  244. 28
  245. 29
  246. 30
  247. 31
  248. 32
  249. 33
  250. 34
  251. 35
  252. 36
  253. 37
  254. 38
  255. 39
  256. 40
  257. 41
  258. 42
  259. 43
  260. 44
  261. 45
  262. 46
  263. 47
  264. 48
  265. 49
  266. 50
  267. 51
  268. 52
  269. 53
  270. 54
  271. 55
  272. 56
  273. 57
  274. 58
  275. 59
  276. 60
  277. 61
  278. 62
  279. 63
  280. 64
  281. 65
  282. 66
  283. 67
  284. 68
  285. 69
  286. 70
  287. 71
  288. 72
  289. 73
  290. 74
  291. 75
  292. 76
  293. 77
  294. 78
  295. 79
  296. 80
  297. 81
  298. 82
  299. 83
  300. 84
  301. 85
  302. 86
  303. 87
  304. 88
  305.  
  306.  
  307. U-Boot 1.1.4-g682743ef (Jan 20 2016 - 14:54:16)
  308.  
  309. =====================================
  310. Caraboot v2.3 (AR9331) U-boot
  311. http://www.8devices.com/
  312. -------------------------------------
  313. DRAM:  64 MB
  314. Flash: 16 MB
  315. Net:   eth0, eth1
  316. =====================================
  317.  
  318. Hit '<ESC>' key(s) to stop autoboot:  1  0
  319. ## Booting image at 9f050000 ...
  320.    Image Name:   MIPS OpenWrt Linux-4.9.184
  321.    Created:      2019-06-27  12:18:52 UTC
  322.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  323.    Data Size:    1378284 Bytes =  1.3 MB
  324.    Load Address: 80060000
  325.    Entry Point:  80060000
  326.    Verifying Checksum at 0x9f050040 ...OK
  327.    Uncompressing Kernel Image ... OK
  328.  
  329. Starting kernel ...
  330.  
  331. [    0.000000] Linux version 4.9.184 (buildbot@2ccc8102e0c3) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292) ) #0 Thu Jun 27 12:18:52 2019
  332. [    0.000000] bootconsole [early0] enabled
  333. [    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
  334. [    0.000000] SoC: Atheros AR9330 rev 1
  335. [    0.000000] Determined physical RAM map:
  336. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  337. [    0.000000] Initrd not found or empty - disabling initrd
  338. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  339. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  340. [    0.000000] Zone ranges:
  341. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
  342. [    0.000000] Movable zone start for each node
  343. [    0.000000] Early memory node ranges
  344. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
  345. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
  346. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  347. [    0.000000] Kernel command line:  board=CARAMBOLA2 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro console=ttyATH0,115200 rootfstype=squashfs noinitrd
  348. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  349. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  350. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  351. [    0.000000] Writing ErrCtl register=00000000
  352. [    0.000000] Readback ErrCtl register=00000000
  353. [    0.000000] Memory: 59964K/65536K available (3393K kernel code, 178K rwdata, 448K rodata, 324K init, 211K bss, 5572K reserved, 0K cma-reserved)
  354. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  355. [    0.000000] NR_IRQS:51
  356. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
  357. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
  358. [    0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
  359. [    0.007910] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  360. [    0.089133] pid_max: default: 32768 minimum: 301
  361. [    0.093910] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  362. [    0.100353] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  363. [    0.111434] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  364. [    0.119816] futex hash table entries: 256 (order: -1, 3072 bytes)
  365. [    0.127764] NET: Registered protocol family 16
  366. [    0.132855] MIPS: machine is 8devices Carambola2 board
  367. [    0.675983] clocksource: Switched to clocksource MIPS
  368. [    0.681152] NET: Registered protocol family 2
  369. [    0.685403] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  370. [    0.691087] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  371. [    0.697404] TCP: Hash tables configured (established 1024 bind 1024)
  372. [    0.703841] UDP hash table entries: 256 (order: 0, 4096 bytes)
  373. [    0.709572] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  374. [    0.716124] NET: Registered protocol family 1
  375. [    0.725198] Crashlog allocated RAM at address 0x3f00000
  376. [    0.730666] workingset: timestamp_bits=30 max_order=14 bucket_order=0
  377. [    0.746075] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  378. [    0.750444] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  379. [    0.773443] io scheduler noop registered
  380. [    0.775913] io scheduler deadline registered (default)
  381. [    0.781677] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  382. [    0.791359] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a AR933X UART
  383. [    0.799735] console [ttyATH0] enabled
  384. [    0.799735] console [ttyATH0] enabled
  385. [    0.806342] bootconsole [early0] disabled
  386. [    0.806342] bootconsole [early0] disabled
  387. [    0.822625] m25p80 spi0.0: found w25q128, expected m25p80
  388. [    0.837506] m25p80 spi0.0: w25q128 (16384 Kbytes)
  389. [    0.840787] 4 cmdlinepart partitions found on MTD device spi0.0
  390. [    0.846682] Creating 4 MTD partitions on "spi0.0":
  391. [    0.851450] 0x000000000000-0x000000040000 : "u-boot"
  392. [    0.859152] 0x000000040000-0x000000050000 : "u-boot-env"
  393. [    0.865906] 0x000000050000-0x000000ff0000 : "firmware"
  394. [    0.892267] 2 uimage-fw partitions found on MTD device firmware
  395. [    0.896784] 0x000000050000-0x0000001b0000 : "kernel"
  396. [    0.903743] 0x0000001b0000-0x000000ff0000 : "rootfs"
  397. [    0.909708] mtd: device 4 (rootfs) set to be root filesystem
  398. [    0.913960] 1 squashfs-split partitions found on MTD device rootfs
  399. [    0.920178] 0x000000400000-0x000000ff0000 : "rootfs_data"
  400. [    0.928586] 0x000000ff0000-0x000001000000 : "art"
  401. [    0.936275] libphy: Fixed MDIO Bus: probed
  402. [    0.959356] libphy: ag71xx_mdio: probed
  403. [    1.587472] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
  404. [    1.629548] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  405. [    2.257700] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  406. [    2.266450] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  407. [    2.273819] NET: Registered protocol family 10
  408. [    2.282415] NET: Registered protocol family 17
  409. [    2.285474] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  410. [    2.298564] 8021q: 802.1Q VLAN Support v1.8
  411. [    2.304979] hctosys: unable to open rtc device (rtc0)
  412. [    2.315435] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  413. [    2.323607] Freeing unused kernel memory: 324K
  414. [    2.326631] This architecture does not have kernel memory protection.
  415. [    2.555998] random: fast init done
  416. [    3.239299] init: Console is alive
  417. [    3.241534] init: - watchdog -
  418. [    4.514474] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  419. [    4.603404] usbcore: registered new interface driver usbfs
  420. [    4.607631] usbcore: registered new interface driver hub
  421. [    4.612886] usbcore: registered new device driver usb
  422. [    4.625083] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  423. [    4.632390] ehci-platform: EHCI generic platform driver
  424. [    4.636366] ehci-platform ehci-platform: EHCI Host Controller
  425. [    4.641950] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  426. [    4.651961] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  427. [    4.686035] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  428. [    4.692157] hub 1-0:1.0: USB hub found
  429. [    4.695019] hub 1-0:1.0: 1 port detected
  430. [    4.699737] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  431. [    4.716412] init: - preinit -
  432. [    5.739592] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  433. Press the [f] key and hit [enter] to enter failsafe mode
  434. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  435. [    7.377237] eth0: link up (1000Mbps/Full duplex)
  436. [    7.380438] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  437. [    9.113545] jffs2: notice: (398) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  438. [    9.129594] mount_root: switching to jffs2 overlay
  439. [    9.172008] urandom-seed: Seeding with /etc/urandom.seed
  440. [    9.453194] eth0: link down
  441. [    9.471453] procd: - early -
  442. [    9.473009] procd: - watchdog -
  443. [   10.158968] procd: - watchdog -
  444. [   10.161029] procd: - ubus -
  445. [   10.301911] random: ubusd: uninitialized urandom read (4 bytes read)
  446. [   10.377225] random: ubusd: uninitialized urandom read (4 bytes read)
  447. [   10.382744] random: ubusd: uninitialized urandom read (4 bytes read)
  448. [   10.389896] procd: - init -
  449. Please press Enter to activate this console.
  450. [   10.871514] kmodloader: loading kernel modules from /etc/modules.d/*
  451. [   10.883101] ip6_tables: (C) 2000-2006 Netfilter Core Team
  452. [   10.902311] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
  453. [   10.908942] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
  454. [   10.919769] ip_tables: (C) 2000-2006 Netfilter Core Team
  455. [   10.935774] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  456. [   11.019297] xt_time: kernel timezone is -0000
  457. [   11.094855] PPP generic driver version 2.4.2
  458. [   11.101354] NET: Registered protocol family 24
  459. [   11.173487] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  460. [   11.219862] kmodloader: done loading kernel modules from /etc/modules.d/*
  461. [   12.788656] urandom_read: 5 callbacks suppressed
  462. [   12.788667] random: jshn: uninitialized urandom read (4 bytes read)
  463. [   12.908068] random: ubusd: uninitialized urandom read (4 bytes read)
  464. [   26.321238] br-lan: port 1(eth0) entered blocking state
  465. [   26.325017] br-lan: port 1(eth0) entered disabled state
  466. [   26.330851] device eth0 entered promiscuous mode
  467. [   26.472697] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  468. [   26.561758] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  469. [   27.997360] eth0: link up (1000Mbps/Full duplex)
  470. [   28.000589] br-lan: port 1(eth0) entered blocking state
  471. [   28.005739] br-lan: port 1(eth0) entered forwarding state
  472. [   28.136131] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  473. [   29.313366] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  474.  
  475.  
  476.  
  477. BusyBox v1.28.4 () built-in shell (ash)
  478.  
  479.   _______                     ________        __
  480.  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  481.  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  482.  |_______||   __|_____|__|__||________||__|  |____|
  483.           |__| W I R E L E S S   F R E E D O M
  484.  -----------------------------------------------------
  485.  OpenWrt 18.06.4, r7808-ef686b7292
  486.  -----------------------------------------------------
  487. === WARNING! =====================================
  488. There is no root password defined on this device!
  489. Use the "passwd" command to set up a new password
  490. in order to prevent unauthorized SSH logins.
  491. --------------------------------------------------
  492. root@OpenWrt:/#
  493. root@OpenWrt:/#
  494. root@OpenWrt:/#
  495.  
  496. ########################################################################################################################
  497. ################ The Ap is still off, counter is started exactly, when device is booted ################################
  498. ########################################################################################################################
  499.  
  500.  
  501. root@OpenWrt:/#
  502. root@OpenWrt:/#
  503. root@OpenWrt:/# while true ; do i=$((i+1)); echo $i  ; sleep 1 ;done
  504. 1
  505. 2
  506. 3
  507. 4
  508. 5
  509. 6
  510. 7
  511. 8
  512. 9
  513. 10
  514. 11
  515. 12
  516. 13
  517. 14
  518. 15
  519. 16
  520. 17
  521. 18
  522. 19
  523. 20
  524. 21
  525. 22
  526. 23
  527. 24
  528. 25
  529. 26
  530. 27
  531. 28
  532. 29
  533. 30
  534. 31
  535. 32
  536. 33
  537. 34
  538. 35
  539. 36
  540. 37
  541. 38
  542. 39
  543. 40
  544. 41
  545. 42
  546. 43
  547. 44
  548. 45
  549. 46
  550. 47
  551. 48
  552. 49
  553. 50
  554. 51
  555. 52
  556. 53
  557. 54
  558. 55
  559. 56
  560.  
  561.  
  562. U-Boot 1.1.4-g682743ef (Jan 20 2016 - 14:54:16)
  563.  
  564. =====================================
  565. Caraboot v2.3 (AR9331) U-boot
  566. http://www.8devices.com/
  567. -------------------------------------
  568. DRAM:  64 MB
  569. Flash: 16 MB
  570. Net:   eth0, eth1
  571. =====================================
  572.  
  573. Hit '<ESC>' key(s) to stop autoboot:  1  0
  574. ## Booting image at 9f050000 ...
  575.    Image Name:   MIPS OpenWrt Linux-4.9.184
  576.    Created:      2019-06-27  12:18:52 UTC
  577.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  578.    Data Size:    1378284 Bytes =  1.3 MB
  579.    Load Address: 80060000
  580.    Entry Point:  80060000
  581.    Verifying Checksum at 0x9f050040 ...OK
  582.    Uncompressing Kernel Image ... OK
  583.  
  584. Starting kernel ...
  585.  
  586. [    0.000000] Linux version 4.9.184 (buildbot@2ccc8102e0c3) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292) ) #0 Thu Jun 27 12:18:52 2019
  587. [    0.000000] bootconsole [early0] enabled
  588. [    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
  589. [    0.000000] SoC: Atheros AR9330 rev 1
  590. [    0.000000] Determined physical RAM map:
  591. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  592. [    0.000000] Initrd not found or empty - disabling initrd
  593. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  594. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  595. [    0.000000] Zone ranges:
  596. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
  597. [    0.000000] Movable zone start for each node
  598. [    0.000000] Early memory node ranges
  599. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
  600. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
  601. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  602. [    0.000000] Kernel command line:  board=CARAMBOLA2 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro console=ttyATH0,115200 rootfstype=squashfs noinitrd
  603. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  604. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  605. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  606. [    0.000000] Writing ErrCtl register=00000000
  607. [    0.000000] Readback ErrCtl register=00000000
  608. [    0.000000] Memory: 59964K/65536K available (3393K kernel code, 178K rwdata, 448K rodata, 324K init, 211K bss, 5572K reserved, 0K cma-reserved)
  609. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  610. [    0.000000] NR_IRQS:51
  611. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
  612. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
  613. [    0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
  614. [    0.007910] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  615. [    0.089133] pid_max: default: 32768 minimum: 301
  616. [    0.093910] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  617. [    0.100353] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  618. [    0.111434] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  619. [    0.119816] futex hash table entries: 256 (order: -1, 3072 bytes)
  620. [    0.127764] NET: Registered protocol family 16
  621. [    0.132855] MIPS: machine is 8devices Carambola2 board
  622. [    0.675983] clocksource: Switched to clocksource MIPS
  623. [    0.681152] NET: Registered protocol family 2
  624. [    0.685403] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  625. [    0.691087] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  626. [    0.697404] TCP: Hash tables configured (established 1024 bind 1024)
  627. [    0.703841] UDP hash table entries: 256 (order: 0, 4096 bytes)
  628. [    0.709572] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  629. [    0.716124] NET: Registered protocol family 1
  630. [    0.725198] Crashlog allocated RAM at address 0x3f00000
  631. [    0.730666] workingset: timestamp_bits=30 max_order=14 bucket_order=0
  632. [    0.746075] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  633. [    0.750444] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  634. [    0.773443] io scheduler noop registered
  635. [    0.775913] io scheduler deadline registered (default)
  636. [    0.781677] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  637. [    0.791359] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a AR933X UART
  638. [    0.799735] console [ttyATH0] enabled
  639. [    0.799735] console [ttyATH0] enabled
  640. [    0.806342] bootconsole [early0] disabled
  641. [    0.806342] bootconsole [early0] disabled
  642. [    0.822625] m25p80 spi0.0: found w25q128, expected m25p80
  643. [    0.837506] m25p80 spi0.0: w25q128 (16384 Kbytes)
  644. [    0.840787] 4 cmdlinepart partitions found on MTD device spi0.0
  645. [    0.846682] Creating 4 MTD partitions on "spi0.0":
  646. [    0.851450] 0x000000000000-0x000000040000 : "u-boot"
  647. [    0.859152] 0x000000040000-0x000000050000 : "u-boot-env"
  648. [    0.865906] 0x000000050000-0x000000ff0000 : "firmware"
  649. [    0.892267] 2 uimage-fw partitions found on MTD device firmware
  650. [    0.896784] 0x000000050000-0x0000001b0000 : "kernel"
  651. [    0.903743] 0x0000001b0000-0x000000ff0000 : "rootfs"
  652. [    0.909708] mtd: device 4 (rootfs) set to be root filesystem
  653. [    0.913960] 1 squashfs-split partitions found on MTD device rootfs
  654. [    0.920178] 0x000000400000-0x000000ff0000 : "rootfs_data"
  655. [    0.928586] 0x000000ff0000-0x000001000000 : "art"
  656. [    0.936275] libphy: Fixed MDIO Bus: probed
  657. [    0.959356] libphy: ag71xx_mdio: probed
  658. [    1.587472] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
  659. [    1.629548] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  660. [    2.257700] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  661. [    2.266450] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  662. [    2.273819] NET: Registered protocol family 10
  663. [    2.282415] NET: Registered protocol family 17
  664. [    2.285474] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  665. [    2.298564] 8021q: 802.1Q VLAN Support v1.8
  666. [    2.304979] hctosys: unable to open rtc device (rtc0)
  667. [    2.315435] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  668. [    2.323607] Freeing unused kernel memory: 324K
  669. [    2.326631] This architecture does not have kernel memory protection.
  670. [    2.555998] random: fast init done
  671. [    3.239299] init: Console is alive
  672. [    3.241534] init: - watchdog -
  673. [    4.514474] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  674. [    4.603404] usbcore: registered new interface driver usbfs
  675. [    4.607631] usbcore: registered new interface driver hub
  676. [    4.612886] usbcore: registered new device driver usb
  677. [    4.625083] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  678. [    4.632390] ehci-platform: EHCI generic platform driver
  679. [    4.636366] ehci-platform ehci-platform: EHCI Host Controller
  680. [    4.641950] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  681. [    4.651961] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  682. [    4.686035] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  683. [    4.692157] hub 1-0:1.0: USB hub found
  684. [    4.695019] hub 1-0:1.0: 1 port detected
  685. [    4.699737] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  686. [    4.716412] init: - preinit -
  687. [    5.739592] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  688. Press the [f] key and hit [enter] to enter failsafe mode
  689. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  690. [    7.377237] eth0: link up (1000Mbps/Full duplex)
  691. [    7.380438] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  692. [    9.113456] jffs2: notice: (398) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  693. [    9.129529] mount_root: switching to jffs2 overlay
  694. [    9.172038] urandom-seed: Seeding with /etc/urandom.seed
  695. [    9.453287] eth0: link down
  696. [    9.471513] procd: - early -
  697. [    9.473069] procd: - watchdog -
  698. [   10.158492] procd: - watchdog -
  699. [   10.160544] procd: - ubus -
  700. [   10.301379] random: ubusd: uninitialized urandom read (4 bytes read)
  701. [   10.376733] random: ubusd: uninitialized urandom read (4 bytes read)
  702. [   10.382256] random: ubusd: uninitialized urandom read (4 bytes read)
  703. [   10.389409] procd: - init -
  704. Please press Enter to activate this console.
  705. [   10.870961] kmodloader: loading kernel modules from /etc/modules.d/*
  706. [   10.882579] ip6_tables: (C) 2000-2006 Netfilter Core Team
  707. [   10.901697] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
  708. [   10.908325] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
  709. [   10.919244] ip_tables: (C) 2000-2006 Netfilter Core Team
  710. [   10.935309] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  711. [   11.018899] xt_time: kernel timezone is -0000
  712. [   11.094738] PPP generic driver version 2.4.2
  713. [   11.101236] NET: Registered protocol family 24
  714. [   11.173720] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  715. [   11.220066] kmodloader: done loading kernel modules from /etc/modules.d/*
  716. [   12.789094] urandom_read: 5 callbacks suppressed
  717. [   12.789106] random: jshn: uninitialized urandom read (4 bytes read)
  718. [   12.815300] random: ubusd: uninitialized urandom read (4 bytes read)
  719. [   26.271061] br-lan: port 1(eth0) entered blocking state
  720. [   26.274842] br-lan: port 1(eth0) entered disabled state
  721. [   26.280680] device eth0 entered promiscuous mode
  722. [   26.332144] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  723. [   26.510979] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  724. [   27.957345] eth0: link up (1000Mbps/Full duplex)
  725. [   27.960583] br-lan: port 1(eth0) entered blocking state
  726. [   27.965730] br-lan: port 1(eth0) entered forwarding state
  727. [   28.140120] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  728. [   29.269027] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  729.  
  730.  
  731.  
  732.  
  733. #########################################################################################################################
  734. #################### After another reboot, the Ap is started, while the device was booting    ###########################
  735. #########################################################################################################################
  736.  
  737.  
  738.  
  739.  
  740.  
  741. U-Boot 1.1.4-g682743ef (Jan 20 2016 - 14:54:16)
  742.  
  743. =====================================
  744. Caraboot v2.3 (AR9331) U-boot
  745. http://www.8devices.com/
  746. -------------------------------------
  747. DRAM:  64 MB
  748. Flash: 16 MB
  749. Net:   eth0, eth1
  750. =====================================
  751.  
  752. Hit '<ESC>' key(s) to stop autoboot:  1  0
  753. ## Booting image at 9f050000 ...
  754.    Image Name:   MIPS OpenWrt Linux-4.9.184
  755.    Created:      2019-06-27  12:18:52 UTC
  756.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  757.    Data Size:    1378284 Bytes =  1.3 MB
  758.    Load Address: 80060000
  759.    Entry Point:  80060000
  760.    Verifying Checksum at 0x9f050040 ...OK
  761.    Uncompressing Kernel Image ... OK
  762.  
  763. Starting kernel ...
  764.  
  765. [    0.000000] Linux version 4.9.184 (buildbot@2ccc8102e0c3) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292) ) #0 Thu Jun 27 12:18:52 2019
  766. [    0.000000] bootconsole [early0] enabled
  767. [    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
  768. [    0.000000] SoC: Atheros AR9330 rev 1
  769. [    0.000000] Determined physical RAM map:
  770. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  771. [    0.000000] Initrd not found or empty - disabling initrd
  772. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  773. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  774. [    0.000000] Zone ranges:
  775. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
  776. [    0.000000] Movable zone start for each node
  777. [    0.000000] Early memory node ranges
  778. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
  779. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
  780. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  781. [    0.000000] Kernel command line:  board=CARAMBOLA2 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro console=ttyATH0,115200 rootfstype=squashfs noinitrd
  782. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  783. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  784. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  785. [    0.000000] Writing ErrCtl register=00000000
  786. [    0.000000] Readback ErrCtl register=00000000
  787. [    0.000000] Memory: 59964K/65536K available (3393K kernel code, 178K rwdata, 448K rodata, 324K init, 211K bss, 5572K reserved, 0K cma-reserved)
  788. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  789. [    0.000000] NR_IRQS:51
  790. [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
  791. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
  792. [    0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
  793. [    0.007910] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  794. [    0.089132] pid_max: default: 32768 minimum: 301
  795. [    0.093909] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  796. [    0.100354] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  797. [    0.111436] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  798. [    0.119824] futex hash table entries: 256 (order: -1, 3072 bytes)
  799. [    0.127773] NET: Registered protocol family 16
  800. [    0.132863] MIPS: machine is 8devices Carambola2 board
  801. [    0.675992] clocksource: Switched to clocksource MIPS
  802. [    0.681161] NET: Registered protocol family 2
  803. [    0.685412] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  804. [    0.691096] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  805. [    0.697412] TCP: Hash tables configured (established 1024 bind 1024)
  806. [    0.703850] UDP hash table entries: 256 (order: 0, 4096 bytes)
  807. [    0.709580] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  808. [    0.716133] NET: Registered protocol family 1
  809. [    0.725207] Crashlog allocated RAM at address 0x3f00000
  810. [    0.730674] workingset: timestamp_bits=30 max_order=14 bucket_order=0
  811. [    0.746073] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  812. [    0.750444] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  813. [    0.773443] io scheduler noop registered
  814. [    0.775913] io scheduler deadline registered (default)
  815. [    0.781676] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  816. [    0.791361] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a AR933X UART
  817. [    0.799735] console [ttyATH0] enabled
  818. [    0.799735] console [ttyATH0] enabled
  819. [    0.806342] bootconsole [early0] disabled
  820. [    0.806342] bootconsole [early0] disabled
  821. [    0.822625] m25p80 spi0.0: found w25q128, expected m25p80
  822. [    0.837507] m25p80 spi0.0: w25q128 (16384 Kbytes)
  823. [    0.840786] 4 cmdlinepart partitions found on MTD device spi0.0
  824. [    0.846681] Creating 4 MTD partitions on "spi0.0":
  825. [    0.851451] 0x000000000000-0x000000040000 : "u-boot"
  826. [    0.859152] 0x000000040000-0x000000050000 : "u-boot-env"
  827. [    0.865907] 0x000000050000-0x000000ff0000 : "firmware"
  828. [    0.892269] 2 uimage-fw partitions found on MTD device firmware
  829. [    0.896792] 0x000000050000-0x0000001b0000 : "kernel"
  830. [    0.903752] 0x0000001b0000-0x000000ff0000 : "rootfs"
  831. [    0.909717] mtd: device 4 (rootfs) set to be root filesystem
  832. [    0.913969] 1 squashfs-split partitions found on MTD device rootfs
  833. [    0.920186] 0x000000400000-0x000000ff0000 : "rootfs_data"
  834. [    0.928595] 0x000000ff0000-0x000001000000 : "art"
  835. [    0.936284] libphy: Fixed MDIO Bus: probed
  836. [    0.959365] libphy: ag71xx_mdio: probed
  837. [    1.587481] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
  838. [    1.629557] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  839. [    2.257709] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  840. [    2.266459] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  841. [    2.273828] NET: Registered protocol family 10
  842. [    2.282424] NET: Registered protocol family 17
  843. [    2.285482] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  844. [    2.298572] 8021q: 802.1Q VLAN Support v1.8
  845. [    2.304984] hctosys: unable to open rtc device (rtc0)
  846. [    2.315434] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  847. [    2.323607] Freeing unused kernel memory: 324K
  848. [    2.326630] This architecture does not have kernel memory protection.
  849. [    2.556007] random: fast init done
  850. [    3.239207] init: Console is alive
  851. [    3.241447] init: - watchdog -
  852. [    4.514388] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  853. [    4.603250] usbcore: registered new interface driver usbfs
  854. [    4.607483] usbcore: registered new interface driver hub
  855. [    4.612732] usbcore: registered new device driver usb
  856. [    4.624935] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  857. [    4.632236] ehci-platform: EHCI generic platform driver
  858. [    4.636209] ehci-platform ehci-platform: EHCI Host Controller
  859. [    4.641794] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  860. [    4.651801] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  861. [    4.686043] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  862. [    4.692168] hub 1-0:1.0: USB hub found
  863. [    4.695029] hub 1-0:1.0: 1 port detected
  864. [    4.699746] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  865. [    4.716419] init: - preinit -
  866. [    5.739600] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  867. Press the [f] key and hit [enter] to enter failsafe mode
  868. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  869. [    7.377245] eth0: link up (1000Mbps/Full duplex)
  870. [    7.380447] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  871. [    9.113764] jffs2: notice: (398) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  872. [    9.129809] mount_root: switching to jffs2 overlay
  873. [    9.172194] urandom-seed: Seeding with /etc/urandom.seed
  874. [    9.454169] eth0: link down
  875. [    9.472514] procd: - early -
  876. [    9.474067] procd: - watchdog -
  877. [   10.159639] procd: - watchdog -
  878. [   10.161691] procd: - ubus -
  879. [   10.303094] random: ubusd: uninitialized urandom read (4 bytes read)
  880. [   10.378147] random: ubusd: uninitialized urandom read (4 bytes read)
  881. [   10.383698] random: ubusd: uninitialized urandom read (4 bytes read)
  882. [   10.390889] procd: - init -
  883. Please press Enter to activate this console.
  884. [   10.872604] kmodloader: loading kernel modules from /etc/modules.d/*
  885. [   10.884199] ip6_tables: (C) 2000-2006 Netfilter Core Team
  886. [   10.903337] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
  887. [   10.909966] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
  888. [   10.920823] ip_tables: (C) 2000-2006 Netfilter Core Team
  889. [   10.936976] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
  890. [   11.020264] xt_time: kernel timezone is -0000
  891. [   11.100333] PPP generic driver version 2.4.2
  892. [   11.106806] NET: Registered protocol family 24
  893. [   11.181940] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  894. [   11.224620] kmodloader: done loading kernel modules from /etc/modules.d/*
  895. [   12.792669] urandom_read: 5 callbacks suppressed
  896. [   12.792680] random: jshn: uninitialized urandom read (4 bytes read)
  897. [   12.912216] random: ubusd: uninitialized urandom read (4 bytes read)
  898. [   26.300867] br-lan: port 1(eth0) entered blocking state
  899. [   26.304654] br-lan: port 1(eth0) entered disabled state
  900. [   26.310488] device eth0 entered promiscuous mode
  901. [   26.339818] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  902. [   26.438111] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  903. [   27.937390] eth0: link up (1000Mbps/Full duplex)
  904. [   27.940621] br-lan: port 1(eth0) entered blocking state
  905. [   27.945774] br-lan: port 1(eth0) entered forwarding state
  906. [   28.056148] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  907. [   29.707003] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  908. [   89.674529] wlan0: authenticate with b0:48:7a:f6:80:aa
  909. [   89.690058] wlan0: send auth to b0:48:7a:f6:80:aa (try 1/3)
  910. [   89.701818] wlan0: authenticated
  911. [   89.766119] wlan0: associate with b0:48:7a:f6:80:aa (try 1/3)
  912. [   89.773825] wlan0: RX AssocResp from b0:48:7a:f6:80:aa (capab=0x431 status=0 aid=1)
  913. [   89.780451] wlan0: associated
  914. [   89.797818] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top