Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # This is an example resource file for seeder1rent. Copy to
- # ~/.seeder1rent.rc and enable/modify the options as needed. Remember to
- # uncomment the options you wish to enable.
- #
- # Based on original .seeder1rent.rc file from http://libtorrent.rakshasa.no/
- # Modified by Lemonberry for rtGui http://rtgui.googlecode.com/
- #
- # This assumes the following directory structure:
- #
- # /Torrents/Downloading - temporaray location for torrents while downloading (see "directory")
- # /Torrents/Complete - Torrents are moved here when complete (see "on_finished")
- # /Torrents/TorrentFiles/Auto - The 'autoload' directory for seeder1rent to use. Place a file
- # in here, and seeder1rent loads it #automatically. (see "schedule = watch_directory")
- # /Torrents/Downloading/seeder1rent.session - for storing seeder1rent session information
- #
- # Maximum and minimum number of peers to connect to per torrent.
- #min_peers = 40
- #max_peers = 250
- # Same as above but for seeding completed torrents (-1 = same as downloading)
- min_peers_seed = -1
- max_peers_seed = -1
- # Maximum number of simultanious uploads per torrent.
- max_uploads = 50
- # Global upload and download rate in KiB. "0" for unlimited.
- download_rate = 0
- upload_rate = 0
- # Default directory to save the downloaded torrents.
- directory = /home/seeder1/rtorrent/download
- # Default session directory. Make sure you don't run multiple instance
- # of seeder1rent using the same session directory. Perhaps using a
- # relative path?
- session = /home/seeder1/rtorrent/.session
- # Watch a directory for new torrents, and stop those that have been
- # deleted.
- schedule = watch_directory,5,5,load_start=/home/seeder1/rtorrent/watch/*.torrent
- schedule = untied_directory,5,5,stop_untied=
- # Close torrents when diskspace is low. */
- schedule = low_diskspace,5,60,close_low_diskspace=100M
- # Stop torrents when reaching upload ratio in percent,
- # when also reaching total upload in bytes, or when
- # reaching final upload ratio in percent.
- # example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
- #schedule = ratio,60,60,stop_on_ratio=200,200M,2000
- # When the torrent finishes, it executes "mv -n <base_path> ~/Download/"
- # and then sets the destination directory to "~/Download/". (0.7.7+)
- # on_finished = move_complete,"execute=mv,-u,$d.get_base_path=,/home/seeder1/download/complete/ ;d.set_directory=/home/seeder1/download/complete/"
- # The ip address reported to the tracker.
- #ip = 127.0.0.1
- #ip = rakshasa.no
- # The ip address the listening socket and outgoing connections is
- # bound to.
- #bind = 127.0.0.1
- #bind = rakshasa.no
- # Port range to use for listening.
- port_range = 22000-22090
- # Start opening ports at a random position within the port range.
- port_random = yes
- scgi_port = 127.0.0.1:5000
- # Check hash for finished torrents. Might be usefull until the bug is
- # fixed that causes lack of diskspace not to be properly reported.
- #check_hash = no
- # Set whetever the client should try to connect to UDP trackers.
- use_udp_trackers = yes
- # Alternative calls to bind and ip that should handle dynamic ip's.
- #schedule = ip_tick,0,1800,ip=rakshasa
- #schedule = bind_tick,0,1800,bind=rakshasa
- # Encryption options, set to none (default) or any combination of the following:
- # allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
- #
- # The example value allows incoming encrypted connections, starts unencrypted
- # outgoing connections but retries with encryption if they fail, preferring
- # plaintext to RC4 encryption after the encrypted handshake
- #
- encryption = allow_incoming,enable_retry,prefer_plaintext
- # Enable DHT support for trackerless torrents or when all trackers are down.
- # May be set to "disable" (completely disable DHT), "off" (do not start DHT),
- # "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
- # The default is "off". For DHT to work, a session directory must be defined.
- #
- dht = enable
- # UDP port to use for DHT.
- #
- dht_port = 6881
- # Enable peer exchange (for torrents not marked private)
- #
- peer_exchange = yes
- #
- # Do not modify the following parameters unless you know what you're doing.
- #
- # Hash read-ahead controls how many MB to request the kernel to read
- # ahead. If the value is too low the disk may not be fully utilized,
- # while if too high the kernel might not be able to keep the read
- # pages in memory thus end up trashing.
- # hash_read_ahead = 16
- # Interval between attempts to check the hash, in milliseconds.
- #hash_interval = 100
- # Number of attempts to check the hash while using the mincore status,
- # before forcing. Overworked systems might need lower values to get a
- # decent hash checking rate.
- #hash_max_tries = 10
- # Max number of files to keep open simultaniously.
- #max_open_files = 128
- # Number of sockets to simultaneously keep open.
- # max_open_sockets = 1024
- # Example of scheduling commands: Switch between two ip's every 5
- # seconds.
- #schedule = "ip_tick1,5,10,ip=torretta"
- #schedule = "ip_tick2,10,10,ip=lampedusa"
- # Remove a scheduled event.
- #schedule_remove = "ip_tick1"
- # Buffer de reception en tcp/ip, purged toutes les 5/6 sec sur le dd...
- # receive_buffer_size = 20M
- # send_buffer_size = 20M
- # Memoire associee a la gestion des chuncks des torrents (parts), en octets.
- # Gouffre a ram spotted, evitez de depasser la moitie de la ram de votre machine si vous comptez la faire tourner pour autre chose en simultanne...
- max_memory_usage = 50M
RAW Paste Data