API tools faq
paste
Advertisement
Guest User

Yocto Dora QT5 Kernel Panic (Reset)

a guest
Jan 19th, 2014
87
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 16.63 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 2013.10 (Jan 05 2014 - 03:40:30)
  2.  
  3. CPU: Freescale i.MX6DL rev1.1 at 792 MHz
  4. Reset cause: POR
  5. Board: Wandboard
  6. DRAM: 1 GiB
  7. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  8. *** Warning - bad CRC, using default environment
  9.  
  10. In: serial
  11. Out: serial
  12. Err: serial
  13. Net: FEC [PRIME]
  14. Hit any key to stop autoboot: 0
  15. mmc0 is current device
  16. reading boot.scr
  17. ** Unable to read file boot.scr **
  18. reading uImage
  19. 3449028 bytes read in 163 ms (20.2 MiB/s)
  20. Booting from mmc ...
  21. reading imx6dl-wandboard.dtb
  22. ** Unable to read file imx6dl-wandboard.dtb **
  23. ## Booting kernel from Legacy Image at 12000000 ...
  24. Image Name: Linux-3.0.35-4.0.0-wandboard+gd3
  25. Image Type: ARM Linux Kernel Image (uncompressed)
  26. Data Size: 3448964 Bytes = 3.3 MiB
  27. Load Address: 10008000
  28. Entry Point: 10008000
  29. Verifying Checksum ... OK
  30. Loading Kernel Image ... OK
  31.  
  32. Starting kernel ...
  33.  
  34. [ 0.000000] Linux version 3.0.35-4.0.0-wandboard+gd35902c (jay@ubuntron) (gcc version 4.8.1 (GCC) ) #1 SMP PREEMPT Sun Jan 5 03:21:08 EST 2014
  35. [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  36. [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  37. [ 0.000000] Machine: Wandboard
  38. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  39. [ 0.000000] CPU identified as i.MX6DL/SOLO, silicon rev 1.1
  40. [ 0.000000] PERCPU: Embedded 7 pages/cpu @cc008000 s5248 r8192 d15232 u32768
  41. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 215040
  42. [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
  43. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  44. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  45. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  46. [ 0.000000] Memory: 592MB 256MB = 848MB total
  47. [ 0.000000] Memory: 852236k/852236k available, 196340k reserved, 262144K highmem
  48. [ 0.000000] Virtual kernel memory layout:
  49. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  50. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  51. [ 0.000000] DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
  52. [ 0.000000] vmalloc : 0xea800000 - 0xf2000000 ( 120 MB)
  53. [ 0.000000] lowmem : 0xc0000000 - 0xea000000 ( 672 MB)
  54. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  55. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  56. [ 0.000000] .init : 0xc0008000 - 0xc0035000 ( 180 kB)
  57. [ 0.000000] .text : 0xc0035000 - 0xc064c1ec (6237 kB)
  58. [ 0.000000] .data : 0xc064e000 - 0xc069d720 ( 318 kB)
  59. [ 0.000000] .bss : 0xc069d744 - 0xc06dfafc ( 265 kB)
  60. [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  61. [ 0.000000] Preemptible hierarchical RCU implementation.
  62. [ 0.000000] NR_IRQS:624
  63. [ 0.000000] MXC GPIO hardware
  64. [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  65. [ 0.000000] Set periph_clk's parent to pll2_pfd_400M!
  66. [ 0.000000] arm_max_freq=1GHz
  67. [ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200')
  68. [ 0.000000] bootconsole [ttymxc0] enabled
  69. [ 0.000000] Console: colour dummy device 80x30
  70. [ 0.213454] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  71. [ 0.301765] pid_max: default: 32768 minimum: 301
  72. [ 0.306742] Mount-cache hash table entries: 512
  73. [ 0.312088] CPU: Testing write buffer coherency: ok
  74. [ 0.317248] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  75. [ 0.417870] CPU1: Booted secondary processor
  76. [ 0.507283] Brought up 2 CPUs
  77. [ 0.514542] SMP: Total of 2 processors activated (3162.11 BogoMIPS).
  78. [ 0.521414] devtmpfs: initialized
  79. [ 0.542197] print_constraints: dummy:
  80. [ 0.546209] NET: Registered protocol family 16
  81. [ 0.554882] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
  82. [ 0.562450] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
  83. [ 0.570190] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
  84. [ 0.577872] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
  85. [ 0.585614] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
  86. [ 0.593267] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
  87. [ 0.681621] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
  88. [ 0.688457] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
  89. [ 0.695801] hw-breakpoint: maximum watchpoint size is 4 bytes.
  90. [ 0.701691] L310 cache controller enabled
  91. [ 0.705719] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B
  92. [ 0.786547] bio: create slab <bio-0> at 0
  93. [ 0.791429] print_constraints: VDDA: 2500 mV
  94. [ 0.796000] print_constraints: VDDIO: 3300 mV
  95. [ 0.800923] vgaarb: loaded
  96. [ 0.804354] SCSI subsystem initialized
  97. [ 0.808790] spi_imx imx6q-ecspi.0: probed
  98. [ 0.813054] spi_imx imx6q-ecspi.1: probed
  99. [ 0.818459] usbcore: registered new interface driver usbfs
  100. [ 0.824104] usbcore: registered new interface driver hub
  101. [ 0.829609] usbcore: registered new device driver usb
  102. [ 0.847282] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  103. [ 0.855424] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
  104. [ 0.861905] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
  105. [ 0.869625] MIPI CSI2 driver module loaded
  106. [ 0.873864] Advanced Linux Sound Architecture Driver Version 1.0.24.
  107. [ 0.881089] Bluetooth: Core ver 2.16
  108. [ 0.884795] NET: Registered protocol family 31
  109. [ 0.889264] Bluetooth: HCI device and connection manager initialized
  110. [ 0.895638] Bluetooth: HCI socket layer initialized
  111. [ 0.900539] Bluetooth: L2CAP socket layer initialized
  112. [ 0.905665] Bluetooth: SCO socket layer initialized
  113. [ 0.910992] cfg80211: Calling CRDA to update world regulatory domain
  114. [ 0.917446] Switching to clocksource mxc_timer1
  115. [ 0.936712] NET: Registered protocol family 2
  116. [ 0.941301] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  117. [ 0.949100] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  118. [ 0.958424] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  119. [ 0.966235] TCP: Hash tables configured (established 131072 bind 65536)
  120. [ 0.972876] TCP reno registered
  121. [ 0.976036] UDP hash table entries: 512 (order: 2, 16384 bytes)
  122. [ 0.982001] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  123. [ 0.988803] NET: Registered protocol family 1
  124. [ 0.993479] RPC: Registered named UNIX socket transport module.
  125. [ 0.999419] RPC: Registered udp transport module.
  126. [ 1.004154] RPC: Registered tcp transport module.
  127. [ 1.008874] RPC: Registered tcp NFSv4.1 backchannel transport module.
  128. [ 1.015523] _regulator_get: etb supply vcore not found, using dummy regulator
  129. [ 1.023157] _regulator_get: etm.0 supply vcore not found, using dummy regulator
  130. [ 1.030557] _regulator_get: etm.1 supply vcore not found, using dummy regulator
  131. [ 1.038236] Static Power Management for Freescale i.MX6
  132. [ 1.043512] wait mode is disabled for i.MX6
  133. [ 1.047877] cpaddr = ea820000 suspend_iram_base=ea8b0000
  134. [ 1.053296] PM driver module loaded
  135. [ 1.773223] link up failed, DB_R0:0x00357f00, DB_R1:0x08200000!
  136. [ 1.779161] IMX PCIe port: link down!
  137. [ 1.783211] IMX usb wakeup probe
  138. [ 1.787053] IMX usb wakeup probe
  139. [ 1.790530] cpu regulator mode:ldo_enable
  140. [ 1.794737] i.MXC CPU frequency driver
  141. [ 1.808587] highmem bounce pool size: 64 pages
  142. [ 1.826763] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  143. [ 1.833546] msgmni has been set to 1152
  144. [ 1.838903] alg: No test for stdrng (krng)
  145. [ 1.843177] io scheduler noop registered
  146. [ 1.847114] io scheduler deadline registered
  147. [ 1.851491] io scheduler cfq registered (default)
  148. [ 1.856994] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
  149. [ 1.863503] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1
  150. [ 1.902090] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
  151. [ 1.980215] Console: switching to colour frame buffer device 240x67
  152. [ 2.021852] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
  153. [ 2.028257] _regulator_get: get() with no identifier
  154. [ 2.037267] imx-sdma imx-sdma: loaded firmware 1.1
  155. [ 2.046175] imx-sdma imx-sdma: initialized
  156. [ 2.185652] Serial: IMX driver
  157. [ 2.188818] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  158. [ 2.195315] console [ttymxc0] enabled, bootconsole disabled
  159. [ 2.195315] console [ttymxc0] enabled, bootconsole disabled
  160. [ 2.207111] imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
  161. [ 2.217843] loop: module loaded
  162. [ 2.221619] FEC Ethernet Driver
  163. [ 2.226629] fec_enet_mii_bus: probed
  164. [ 2.231048] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  165. [ 2.237703] add wake up source irq 75
  166. [ 2.243804] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  167. [ 2.250509] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  168. [ 2.282037] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
  169. [ 2.302058] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  170. [ 2.308412] hub 1-0:1.0: USB hub found
  171. [ 2.312187] hub 1-0:1.0: 1 port detected
  172. [ 2.316309] add wake up source irq 72
  173. [ 2.320011] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  174. [ 2.326659] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  175. [ 2.362033] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
  176. [ 2.382030] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  177. [ 2.388251] hub 2-0:1.0: USB hub found
  178. [ 2.392032] hub 2-0:1.0: 1 port detected
  179. [ 2.396282] Initializing USB Mass Storage driver...
  180. [ 2.401316] usbcore: registered new interface driver usb-storage
  181. [ 2.407338] USB Mass Storage support registered.
  182. [ 2.412218] ARC USBOTG Device Controller driver (1 August 2005)
  183. [ 2.418184] udc: request mem region for fsl-usb2-udc failed
  184. [ 2.423864] fsl-usb2-udc: probe of fsl-usb2-udc failed with error -16
  185. [ 2.430700] mousedev: PS/2 mouse device common for all mice
  186. [ 2.436839] input: prism_st as /devices/virtual/input/input0
  187. [ 2.443032] prism : creating workqueue e23195a0
  188. [ 2.447580] prism : request irq : 0
  189. [ 2.451232] prism : read complete : 0
  190. [ 2.454905] prism : probe succesful
  191. [ 2.458623] i2c /dev entries driver
  192. [ 2.462924] Linux video capture interface: v2.00
  193. [ 2.467928] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
  194. [ 2.475571] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
  195. [ 2.483198] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
  196. [ 2.490879] Bluetooth: HCI UART driver ver 2.2
  197. [ 2.495364] Bluetooth: HCI H4 protocol initialized
  198. [ 2.500289] sdhci: Secure Digital Host Controller Interface driver
  199. [ 2.506503] sdhci: Copyright(c) Pierre Ossman
  200. [ 2.510980] _regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dummy regulator
  201. [ 2.519511] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
  202. [ 2.527512] _regulator_get: sdhci-esdhc-imx.1 supply vmmc not found, using dummy regulator
  203. [ 2.540852] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA
  204. [ 2.548047] sdhci sdhci-esdhc-imx.0: no write-protect pin available!
  205. [ 2.561708] _regulator_get: sdhci-esdhc-imx.0 supply vmmc not found, using dummy regulator
  206. [ 2.582276] mmc2: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
  207. [ 2.591252] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  208. [ 2.601953] VPU initialized
  209. [ 2.605780] mxc_asrc registered
  210. [ 2.612227] Galcore version 4.6.9.6622
  211. [ 2.628565] Thermal calibration data is 0x59c5305f
  212. [ 2.633387] Thermal sensor with ratio = 186
  213. [ 2.652040] Anatop Thermal registered as thermal_zone0
  214. [ 2.657322] anatop_thermal_probe: default cooling device is cpufreq!
  215. [ 2.664436] usbcore: registered new interface driver usbhid
  216. [ 2.670011] usbhid: USB HID core driver
  217. [ 2.674383] usbcore: registered new interface driver snd-usb-audio
  218. [ 2.681106] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
  219. [ 2.686505] mxc_spdif mxc_spdif.0: MXC SPDIF Audio
  220. [ 2.693484] _regulator_get: 1-000a supply VDDD not found, using dummy regulator
  221. [ 2.703398] sgtl5000 1-000a: sgtl5000 revision 17
  222. [ 2.708338] print_constraints: 1-000a: 850 <--> 1600 mV at 1200 mV normal
  223. [ 2.736847] mmc0: new high speed SDHC card at address 1234
  224. [ 2.742884] mmcblk0: mmc0:1234 SA16G 14.8 GiB
  225. [ 2.752383] mmcblk0: p1 p2
  226. [ 2.758304] asoc: sgtl5000 <-> imx-ssi.1 mapping ok
  227. [ 2.765603] asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok
  228. [ 2.776181] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
  229. [ 2.783007] ALSA device list:
  230. [ 2.785978] #0: sgtl5000-audio
  231. [ 2.789206] #1: imx-spdif
  232. [ 2.792002] #2: imx-hdmi-soc
  233. [ 2.795574] TCP cubic registered
  234. [ 2.798806] NET: Registered protocol family 17
  235. [ 2.803361] Bluetooth: RFCOMM socket layer initialized
  236. [ 2.810157] Bluetooth: RFCOMM ver 1.11
  237. [ 2.815568] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  238. [ 2.820884] Bluetooth: BNEP filters: multicast
  239. [ 2.825388] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  240. [ 2.831837] lib80211: common routines for IEEE802.11 drivers
  241. [ 2.839176] Registering the dns_resolver key type
  242. [ 2.846309] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  243. [ 2.854022] ThumbEE CPU extension supported.
  244. [ 2.858687] Bus freq driver module loaded
  245. [ 2.862721] Bus freq driver Enabled
  246. [ 2.868140] mxc_dvfs_core_probe
  247. [ 2.871530] DVFS driver module loaded
  248. [ 2.876305] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  249. [ 2.912408] EXT3-fs: barriers not enabled
  250. [ 2.926507] kjournald starting. Commit interval 5 seconds
  251. [ 2.938179] EXT3-fs (mmcblk0p2): using internal journal
  252. [ 2.943425] EXT3-fs (mmcblk0p2): recovery complete
  253. [ 2.948225] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
  254. [ 2.955316] VFS: Mounted root (ext3 filesystem) on device 179:2.
  255. [ 2.981665] devtmpfs: mounted
  256. [ 2.984709] Freeing init memory: 180K
  257. [ 3.056668] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
  258. [ 3.069147] [<c0041f3c>] (unwind_backtrace+0x0/0xf4) from [<c04aff04>] (panic+0x84/0x198)
  259. [ 3.077347] [<c04aff04>] (panic+0x84/0x198) from [<c04af89c>] (cpu_has_aliasing_icache.part.3+0x0/0x3c)
  260. [ 3.086812] CPU0: stopping
  261. [ 3.089538] [<c0041f3c>] (unwind_backtrace+0x0/0xf4) from [<c0035338>] (do_IPI+0x144/0x154)
  262. [ 3.097903] [<c0035338>] (do_IPI+0x144/0x154) from [<c003a9cc>] (__irq_svc+0x4c/0xe8)
  263. [ 3.105734] Exception stack(0xe2057d70 to 0xe2057db8)
  264. [ 3.110789] 7d60: e2603b08 20000013 000025ed 00000000
  265. [ 3.118970] 7d80: e2603800 e26039fc e2603ae0 e2603b08 20000013 00000000 00000000 00000000
  266. [ 3.127150] 7da0: c034a6e4 e2057db8 c03483dc c04b62f8 40000013 ffffffff
  267. [ 3.133780] [<c003a9cc>] (__irq_svc+0x4c/0xe8) from [<c04b62f8>] (_raw_spin_unlock_irqrestore+0x18/0x4c)
  268. [ 3.143273] [<c04b62f8>] (_raw_spin_unlock_irqrestore+0x18/0x4c) from [<c03483dc>] (sdhci_set_ios+0x298/0x5ec)
  269. [ 3.153288] [<c03483dc>] (sdhci_set_ios+0x298/0x5ec) from [<c0337cfc>] (__mmc_set_clock+0x50/0x68)
  270. [ 3.162256] [<c0337cfc>] (__mmc_set_clock+0x50/0x68) from [<c03396f4>] (mmc_host_clk_hold+0x40/0x6c)
  271. [ 3.171406] [<c03396f4>] (mmc_host_clk_hold+0x40/0x6c) from [<c0336888>] (__mmc_start_req+0xd0/0x12c)
  272. [ 3.180632] [<c0336888>] (__mmc_start_req+0xd0/0x12c) from [<c0336a98>] (mmc_wait_for_cmd+0x74/0xa0)
  273. [ 3.189771] [<c0336a98>] (mmc_wait_for_cmd+0x74/0xa0) from [<c033f3d4>] (mmc_io_rw_direct_host+0xa0/0x150)
  274. [ 3.199431] [<c033f3d4>] (mmc_io_rw_direct_host+0xa0/0x150) from [<c0340124>] (sdio_read_cis+0x168/0x288)
  275. [ 3.209008] [<c0340124>] (sdio_read_cis+0x168/0x288) from [<c033e9a4>] (mmc_sdio_init_card+0x25c/0x5e0)
  276. [ 3.218407] [<c033e9a4>] (mmc_sdio_init_card+0x25c/0x5e0) from [<c033f01c>] (mmc_attach_sdio+0x8c/0x3a4)
  277. [ 3.227893] [<c033f01c>] (mmc_attach_sdio+0x8c/0x3a4) from [<c0338b7c>] (mmc_rescan+0x1f0/0x254)
  278. [ 3.236690] [<c0338b7c>] (mmc_rescan+0x1f0/0x254) from [<c0082838>] (process_one_work+0x10c/0x3c4)
  279. [ 3.245657] [<c0082838>] (process_one_work+0x10c/0x3c4) from [<c0082e40>] (worker_thread+0x15c/0x3b0)
  280. [ 3.254884] [<c0082e40>] (worker_thread+0x15c/0x3b0) from [<c0087364>] (kthread+0x84/0x88)
  281. [ 3.263155] [<c0087364>] (kthread+0x84/0x88) from [<c003ba7c>] (kernel_thread_exit+0x0/0x8)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!