Guest User

Untitled

a guest
Aug 16th, 2012
80
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. [ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Mon Aug 6 18:26:34 CEST 2012
  2. [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
  3. [ 0.000000] CPU frequency is 320 MHz
  4. [ 0.000000] 64MB of RAM installed
  5. [ 0.000000] registering 32 GPIOs
  6. [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
  7. [ 0.000000] board_bcm963xx: Boot address 0xb8000000
  8. [ 0.000000] board_bcm963xx: CFE version: 1.0.37-110.11
  9. [ 0.000000] bootconsole [early0] enabled
  10. [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
  11. [ 0.000000] board_bcm963xx: board name: 96328A-1441N1
  12. [ 0.000000] Determined physical RAM map:
  13. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  14. [ 0.000000] Initrd not found or empty - disabling initrd
  15. [ 0.000000] Zone PFN ranges:
  16. [ 0.000000] Normal 0x00000000 -> 0x00004000
  17. [ 0.000000] Movable zone start PFN for each node
  18. [ 0.000000] Early memory PFN ranges
  19. [ 0.000000] 0: 0x00000000 -> 0x00004000
  20. [ 0.000000] On node 0 totalpages: 16384
  21. [ 0.000000] free_area_init_node: node 0, pgdat 802ace90, node_mem_map 81000000
  22. [ 0.000000] Normal zone: 128 pages used for memmap
  23. [ 0.000000] Normal zone: 0 pages reserved
  24. [ 0.000000] Normal zone: 16256 pages, LIFO batch:3
  25. [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
  26. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  27. [ 0.000000] pcpu-alloc: [0] 0
  28. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  29. [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  30. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  31. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  32. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  33. [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
  34. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  35. [ 0.000000] Memory: 61808k/65536k available (2261k kernel code, 3728k reserved, 415k data, 204k init, 0k highmem)
  36. [ 0.000000] NR_IRQS:128
  37. [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
  38. [ 0.036000] pid_max: default: 32768 minimum: 301
  39. [ 0.040000] Mount-cache hash table entries: 512
  40. [ 0.048000] NET: Registered protocol family 16
  41. [ 0.276000] registering PCI controller with io_map_base unset
  42. [ 0.288000] bio: create slab <bio-0> at 0
  43. [ 0.292000] PCI host bridge to bus 0000:00
  44. [ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
  45. [ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  46. [ 0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604
  47. [ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot
  48. [ 0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280
  49. [ 0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
  50. [ 0.304000] pci 0000:01:00.0: supports D1 D2
  51. [ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
  52. [ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
  53. [ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
  54. [ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
  55. [ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  56. [ 0.324000] Switching to clocksource MIPS
  57. [ 0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
  58. [ 0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
  59. [ 0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
  60. [ 0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
  61. [ 0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
  62. [ 0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606)
  63. [ 0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9
  64. [ 0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9
  65. [ 0.408000] bcma: bus0: SPROM offset 0x800
  66. [ 0.448000] bcma: Reading SPROM failed. Trying fallback SPROM...
  67. [ 0.448000] bcm63xx_sprom_bcma: filled BCMA SPROM for chip id 0xa8d9
  68. [ 0.452000] bcma: bus0: Using SPROM revision 8 provided by platform.
  69. [ 0.452000] bcma: bus0: Bus registered
  70. [ 0.456000] NET: Registered protocol family 2
  71. [ 0.464000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  72. [ 0.472000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  73. [ 0.476000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
  74. [ 0.484000] TCP: Hash tables configured (established 2048 bind 2048)
  75. [ 0.492000] TCP reno registered
  76. [ 0.496000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  77. [ 0.500000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  78. [ 0.508000] NET: Registered protocol family 1
  79. [ 0.512000] PCI: CLS 0 bytes, default 16
  80. [ 0.516000] audit: initializing netlink socket (disabled)
  81. [ 0.520000] type=2000 audit(0.520:1): initialized
  82. [ 0.528000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  83. [ 0.532000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  84. [ 0.544000] msgmni has been set to 120
  85. [ 0.548000] io scheduler noop registered
  86. [ 0.552000] io scheduler deadline registered (default)
  87. [ 0.560000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
  88. [ 0.568000] console [ttyS0] enabled, bootconsole disabled
  89. [ 0.584000] m25p80 spi0.0: found mx25l12805d, expected m25p80
  90. [ 0.592000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
  91. [ 0.596000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1441N1
  92. [ 0.604000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
  93. [ 0.612000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00
  94. [ 0.620000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000
  95. [ 0.624000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
  96. [ 0.632000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
  97. [ 0.640000] bcm63xxpart: Spare partition is offset 310004 and length cdfffc
  98. [ 0.648000] 5 bcm63xxpart partitions found on MTD device spi0.0
  99. [ 0.652000] Creating 5 MTD partitions on "spi0.0":
  100. [ 0.660000] 0x000000000000-0x000000010000 : "CFE"
  101. [ 0.664000] 0x000000010100-0x000000100000 : "kernel"
  102. [ 0.672000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  103. [ 0.688000] 0x000000100000-0x000000ff0000 : "rootfs"
  104. [ 0.696000] mtd: partition "rootfs" set to be root filesystem
  105. [ 0.700000] mtd: partition "rootfs_data" created automatically, ofs=310000, len=CE0000
  106. [ 0.708000] 0x000000310000-0x000000ff0000 : "rootfs_data"
  107. [ 0.716000] 0x000000ff0000-0x000001000000 : "nvram"
  108. [ 0.724000] 0x000000010000-0x000000ff0000 : "linux"
  109. [ 0.768000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
  110. [ 0.776000] Registered led device: 96328A-1441N1:green:power
  111. [ 0.776000] Registered led device: 96328A-1441N1:red:power
  112. [ 0.776000] Registered led device: 96328A-1441N1:green:inet
  113. [ 0.776000] Registered led device: 96328A-1441N1:red:inet
  114. [ 0.780000] Registered led device: 96328A-1441N1:green:dsl
  115. [ 0.780000] TCP cubic registered
  116. [ 0.784000] NET: Registered protocol family 17
  117. [ 0.788000] 8021q: 802.1Q VLAN Support v1.8
  118. [ 0.800000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  119. [ 0.808000] Freeing unused kernel memory: 204k freed
  120. [ 3.448000] roboswitch: Probing device eth0:
  121. [ 3.452000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external
  122. [ 3.460000] No Robo switch in managed mode found, phy_id = 0xffffffff
  123. [ 3.468000] roboswitch: Probing device eth1: No such device
  124. [ 3.472000] roboswitch: Probing device eth2: No such device
  125. [ 3.480000] roboswitch: Probing device eth3: No such device
  126. [ 5.972000] Button Hotplug driver version 0.4.1
  127. [ 9.892000] JFFS2 notice: (349) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
  128. [ 12.768000] Compat-wireless backport release: compat-wireless-2012-07-13
  129. [ 12.776000] Backport based on wireless-testing.git master-2012-07-16
  130. [ 12.780000] compat.git: wireless-testing.git
  131. [ 12.840000] cfg80211: Calling CRDA to update world regulatory domain
  132. [ 12.844000] cfg80211: World regulatory domain updated:
  133. [ 12.848000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  134. [ 12.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  135. [ 12.868000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  136. [ 12.876000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  137. [ 12.884000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  138. [ 12.892000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  139. [ 13.284000] NET: Registered protocol family 10
  140. [ 13.704000] SCSI subsystem initialized
  141. [ 13.752000] There is already a switch registered on the device 'eth0'
  142. [ 13.760000] roboswitch: Probing device eth1: No such device
  143. [ 13.764000] roboswitch: Probing device eth2: No such device
  144. [ 13.768000] roboswitch: Probing device eth3: No such device
  145. [ 14.044000] usbcore: registered new interface driver usbfs
  146. [ 14.048000] usbcore: registered new interface driver hub
  147. [ 14.056000] usbcore: registered new device driver usb
  148. [ 14.740000] PPP generic driver version 2.4.2
  149. [ 15.180000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31
  150. [ 15.528000] bcma: bus0: Switched to core: 0x812
  151. [ 15.532000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  152. [ 15.676000] ip_tables: (C) 2000-2006 Netfilter Core Team
  153. [ 16.148000] NET: Registered protocol family 24
  154. [ 16.456000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  155. [ 16.568000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
  156. [ 16.572000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
  157. [ 16.604000] bcm63xx_ehci bcm63xx_ehci.0: irq 50, io mem 0xb0002500
  158. [ 16.620000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
  159. [ 16.628000] hub 1-0:1.0: USB hub found
  160. [ 16.632000] hub 1-0:1.0: 1 port detected
  161. [ 16.672000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
  162. [ 17.568000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  163. [ 17.876000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  164. [ 17.988000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
  165. [ 17.992000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
  166. [ 18.000000] bcm63xx_ohci bcm63xx_ohci.0: irq 49, io mem 0xb0002600
  167. [ 18.068000] hub 2-0:1.0: USB hub found
  168. [ 18.072000] hub 2-0:1.0: 1 port detected
  169. [ 18.116000] Initializing USB Mass Storage driver...
  170. [ 18.120000] usbcore: registered new interface driver usb-storage
  171. [ 18.128000] USB Mass Storage support registered.
  172. [ 18.292000] usbcore: registered new interface driver ums-alauda
  173. [ 18.320000] usbcore: registered new interface driver ums-cypress
  174. [ 18.352000] usbcore: registered new interface driver ums-datafab
  175. [ 18.380000] usbcore: registered new interface driver ums-freecom
  176. [ 18.408000] usbcore: registered new interface driver ums-isd200
  177. [ 18.436000] usbcore: registered new interface driver ums-jumpshot
  178. [ 18.468000] usbcore: registered new interface driver ums-karma
  179. [ 18.496000] usbcore: registered new interface driver ums-sddr09
  180. [ 18.528000] usbcore: registered new interface driver ums-sddr55
  181. [ 18.696000] usbcore: registered new interface driver ums-usbat
  182. [ 18.728000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
  183. [ 22.552000] device eth0 entered promiscuous mode
  184. [ 22.560000] br-lan: port 1(eth0) entered forwarding state
  185. [ 22.564000] br-lan: port 1(eth0) entered forwarding state
  186. [ 24.508000] cfg80211: Calling CRDA for country: ES
  187. [ 24.512000] cfg80211: Regulatory domain changed to country: ES
  188. [ 24.520000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  189. [ 24.528000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  190. [ 24.536000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  191. [ 24.544000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  192. [ 24.552000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
  193. [ 24.568000] br-lan: port 1(eth0) entered forwarding state
  194. [ 26.848000] dummy
  195. [ 26.848000] dummy
  196. [ 26.852000] dummy
  197. [ 26.852000] dummy
  198. [ 26.856000] dummy
  199. [ 26.856000] dummy
  200. [ 26.860000] dummy
  201. [ 26.860000] dummy
  202. [ 26.864000] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
  203. [ 26.872000] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
  204. [ 26.892000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
  205. [ 111.552000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
RAW Paste Data