SHARE
TWEET

Yocto Dora QT5 Kernel Panic (First Boot)

a guest Jan 19th, 2014 98 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot 2013.10 (Jan 05 2014 - 03:40:30)
  2.  
  3. CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
  4. Reset cause: POR
  5. Board: Wandboard
  6. DRAM:  1 GiB
  7. MMC:   FSL_SDHC: 0, FSL_SDHC: 1
  8. *** Warning - bad CRC, using default environment
  9.  
  10. In:    serial
  11. Out:   serial
  12. Err:   serial
  13. Net:   FEC [PRIME]
  14. Hit any key to stop autoboot:  0
  15. mmc0 is current device
  16. reading boot.scr
  17. ** Unable to read file boot.scr **
  18. reading uImage
  19. 3449028 bytes read in 163 ms (20.2 MiB/s)
  20. Booting from mmc ...
  21. reading imx6dl-wandboard.dtb
  22. ** Unable to read file imx6dl-wandboard.dtb **
  23. ## Booting kernel from Legacy Image at 12000000 ...
  24.    Image Name:   Linux-3.0.35-4.0.0-wandboard+gd3
  25.    Image Type:   ARM Linux Kernel Image (uncompressed)
  26.    Data Size:    3448964 Bytes = 3.3 MiB
  27.    Load Address: 10008000
  28.    Entry Point:  10008000
  29.    Verifying Checksum ... OK
  30.    Loading Kernel Image ... OK
  31.  
  32. Starting kernel ...
  33.  
  34. [    0.000000] Linux version 3.0.35-4.0.0-wandboard+gd35902c (jay@ubuntron) (gcc version 4.8.1 (GCC) ) #1 SMP PREEMPT Sun Jan 5 03:21:08 EST 2014
  35. [    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  36. [    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  37. [    0.000000] Machine: Wandboard
  38. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
  39. [    0.000000] CPU identified as i.MX6DL/SOLO, silicon rev 1.1
  40. [    0.000000] PERCPU: Embedded 7 pages/cpu @cc008000 s5248 r8192 d15232 u32768
  41. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 215040
  42. [    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
  43. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  44. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  45. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  46. [    0.000000] Memory: 592MB 256MB = 848MB total
  47. [    0.000000] Memory: 852236k/852236k available, 196340k reserved, 262144K highmem
  48. [    0.000000] Virtual kernel memory layout:
  49. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  50. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  51. [    0.000000]     DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)
  52. [    0.000000]     vmalloc : 0xea800000 - 0xf2000000   ( 120 MB)
  53. [    0.000000]     lowmem  : 0xc0000000 - 0xea000000   ( 672 MB)
  54. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  55. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  56. [    0.000000]       .init : 0xc0008000 - 0xc0035000   ( 180 kB)
  57. [    0.000000]       .text : 0xc0035000 - 0xc064c1ec   (6237 kB)
  58. [    0.000000]       .data : 0xc064e000 - 0xc069d720   ( 318 kB)
  59. [    0.000000]        .bss : 0xc069d744 - 0xc06dfafc   ( 265 kB)
  60. [    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  61. [    0.000000] Preemptible hierarchical RCU implementation.
  62. [    0.000000] NR_IRQS:624
  63. [    0.000000] MXC GPIO hardware
  64. [    0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  65. [    0.000000] Set periph_clk's parent to pll2_pfd_400M!
  66. [    0.000000] arm_max_freq=1GHz
  67. [    0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200')
  68. [    0.000000] bootconsole [ttymxc0] enabled
  69. [    0.000000] Console: colour dummy device 80x30
  70. [    0.213450] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  71. [    0.301756] pid_max: default: 32768 minimum: 301
  72. [    0.306726] Mount-cache hash table entries: 512
  73. [    0.312071] CPU: Testing write buffer coherency: ok
  74. [    0.317233] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  75. [    0.417854] CPU1: Booted secondary processor
  76. [    0.457269] Brought up 2 CPUs
  77. [    0.464527] SMP: Total of 2 processors activated (3162.11 BogoMIPS).
  78. [    0.471384] devtmpfs: initialized
  79. [    0.492080] print_constraints: dummy:
  80. [    0.496095] NET: Registered protocol family 16
  81. [    0.504750] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
  82. [    0.512328] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
  83. [    0.520065] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
  84. [    0.527752] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
  85. [    0.535495] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
  86. [    0.543150] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
  87. [    0.631601] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
  88. [    0.638435] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
  89. [    0.645779] hw-breakpoint: maximum watchpoint size is 4 bytes.
  90. [    0.651668] L310 cache controller enabled
  91. [    0.655696] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B
  92. [    0.736466] bio: create slab <bio-0> at 0
  93. [    0.741336] print_constraints: VDDA: 2500 mV
  94. [    0.745904] print_constraints: VDDIO: 3300 mV
  95. [    0.750822] vgaarb: loaded
  96. [    0.754241] SCSI subsystem initialized
  97. [    0.758681] spi_imx imx6q-ecspi.0: probed
  98. [    0.762942] spi_imx imx6q-ecspi.1: probed
  99. [    0.768349] usbcore: registered new interface driver usbfs
  100. [    0.773991] usbcore: registered new interface driver hub
  101. [    0.779481] usbcore: registered new device driver usb
  102. [    0.797265] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  103. [    0.805375] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
  104. [    0.811851] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
  105. [    0.819572] MIPI CSI2 driver module loaded
  106. [    0.823811] Advanced Linux Sound Architecture Driver Version 1.0.24.
  107. [    0.831043] Bluetooth: Core ver 2.16
  108. [    0.834743] NET: Registered protocol family 31
  109. [    0.839212] Bluetooth: HCI device and connection manager initialized
  110. [    0.845586] Bluetooth: HCI socket layer initialized
  111. [    0.850484] Bluetooth: L2CAP socket layer initialized
  112. [    0.855610] Bluetooth: SCO socket layer initialized
  113. [    0.860943] cfg80211: Calling CRDA to update world regulatory domain
  114. [    0.867391] Switching to clocksource mxc_timer1
  115. [    0.886679] NET: Registered protocol family 2
  116. [    0.891267] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  117. [    0.899068] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  118. [    0.908393] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  119. [    0.916373] TCP: Hash tables configured (established 131072 bind 65536)
  120. [    0.923015] TCP reno registered
  121. [    0.926174] UDP hash table entries: 512 (order: 2, 16384 bytes)
  122. [    0.932147] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  123. [    0.938942] NET: Registered protocol family 1
  124. [    0.943620] RPC: Registered named UNIX socket transport module.
  125. [    0.949559] RPC: Registered udp transport module.
  126. [    0.954292] RPC: Registered tcp transport module.
  127. [    0.959009] RPC: Registered tcp NFSv4.1 backchannel transport module.
  128. [    0.965663] _regulator_get: etb supply vcore not found, using dummy regulator
  129. [    0.973288] _regulator_get: etm.0 supply vcore not found, using dummy regulator
  130. [    0.980687] _regulator_get: etm.1 supply vcore not found, using dummy regulator
  131. [    0.988367] Static Power Management for Freescale i.MX6
  132. [    0.993644] wait mode is disabled for i.MX6
  133. [    0.998008] cpaddr = ea820000 suspend_iram_base=ea8b0000
  134. [    1.003428] PM driver module loaded
  135. [    1.723162] link up failed, DB_R0:0x00f54800, DB_R1:0x08200000!
  136. [    1.729100] IMX PCIe port: link down!
  137. [    1.733156] IMX usb wakeup probe
  138. [    1.736986] IMX usb wakeup probe
  139. [    1.740462] cpu regulator mode:ldo_enable
  140. [    1.744667] i.MXC CPU frequency driver
  141. [    1.758503] highmem bounce pool size: 64 pages
  142. [    1.776729] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  143. [    1.783512] msgmni has been set to 1152
  144. [    1.788852] alg: No test for stdrng (krng)
  145. [    1.793130] io scheduler noop registered
  146. [    1.797066] io scheduler deadline registered
  147. [    1.801444] io scheduler cfq registered (default)
  148. [    1.806942] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
  149. [    1.813451] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1
  150. [    1.852036] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
  151. [    1.930153] Console: switching to colour frame buffer device 240x67
  152. [    1.971824] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
  153. [    1.978229] _regulator_get: get() with no identifier
  154. [    1.987252] imx-sdma imx-sdma: loaded firmware 1.1
  155. [    1.996149] imx-sdma imx-sdma: initialized
  156. [    2.135428] Serial: IMX driver
  157. [    2.138593] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  158. [    2.145087] console [ttymxc0] enabled, bootconsole disabled
  159. [    2.145087] console [ttymxc0] enabled, bootconsole disabled
  160. [    2.156829] imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
  161. [    2.167530] loop: module loaded
  162. [    2.171302] FEC Ethernet Driver
  163. [    2.176304] fec_enet_mii_bus: probed
  164. [    2.180724] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  165. [    2.187385] add wake up source irq 75
  166. [    2.193485] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  167. [    2.200187] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  168. [    2.231982] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
  169. [    2.252002] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  170. [    2.258354] hub 1-0:1.0: USB hub found
  171. [    2.262129] hub 1-0:1.0: 1 port detected
  172. [    2.266254] add wake up source irq 72
  173. [    2.269956] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  174. [    2.276602] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  175. [    2.311985] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
  176. [    2.331976] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  177. [    2.338185] hub 2-0:1.0: USB hub found
  178. [    2.341947] hub 2-0:1.0: 1 port detected
  179. [    2.346213] Initializing USB Mass Storage driver...
  180. [    2.351248] usbcore: registered new interface driver usb-storage
  181. [    2.357266] USB Mass Storage support registered.
  182. [    2.362154] ARC USBOTG Device Controller driver (1 August 2005)
  183. [    2.368123] udc: request mem region for fsl-usb2-udc failed
  184. [    2.373800] fsl-usb2-udc: probe of fsl-usb2-udc failed with error -16
  185. [    2.380643] mousedev: PS/2 mouse device common for all mice
  186. [    2.386774] input: prism_st as /devices/virtual/input/input0
  187. [    2.392972] prism : creating workqueue e26705a0
  188. [    2.397520] prism : request irq : 0
  189. [    2.401171] prism : read complete : 0
  190. [    2.404842] prism : probe succesful
  191. [    2.408554] i2c /dev entries driver
  192. [    2.412842] Linux video capture interface: v2.00
  193. [    2.417840] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
  194. [    2.425479] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
  195. [    2.433111] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
  196. [    2.440787] Bluetooth: HCI UART driver ver 2.2
  197. [    2.445272] Bluetooth: HCI H4 protocol initialized
  198. [    2.450202] sdhci: Secure Digital Host Controller Interface driver
  199. [    2.456416] sdhci: Copyright(c) Pierre Ossman
  200. [    2.460894] _regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dummy regulator
  201. [    2.469423] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
  202. [    2.477425] _regulator_get: sdhci-esdhc-imx.1 supply vmmc not found, using dummy regulator
  203. [    2.490759] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA
  204. [    2.497955] sdhci sdhci-esdhc-imx.0: no write-protect pin available!
  205. [    2.511613] _regulator_get: sdhci-esdhc-imx.0 supply vmmc not found, using dummy regulator
  206. [    2.532193] mmc2: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
  207. [    2.541169] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  208. [    2.551863] VPU initialized
  209. [    2.555692] mxc_asrc registered
  210. [    2.562177] Galcore version 4.6.9.6622
  211. [    2.579428] Thermal calibration data is 0x59c5305f
  212. [    2.584245] Thermal sensor with ratio = 186
  213. [    2.601986] Anatop Thermal registered as thermal_zone0
  214. [    2.607270] anatop_thermal_probe: default cooling device is cpufreq!
  215. [    2.614386] usbcore: registered new interface driver usbhid
  216. [    2.619960] usbhid: USB HID core driver
  217. [    2.624349] usbcore: registered new interface driver snd-usb-audio
  218. [    2.631095] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
  219. [    2.636494] mxc_spdif mxc_spdif.0: MXC SPDIF Audio
  220. [    2.643480] _regulator_get: 1-000a supply VDDD not found, using dummy regulator
  221. [    2.653340] sgtl5000 1-000a: sgtl5000 revision 17
  222. [    2.658289] print_constraints: 1-000a: 850 <--> 1600 mV at 1200 mV normal
  223. [    2.686801] mmc0: new high speed SDHC card at address 1234
  224. [    2.692843] mmcblk0: mmc0:1234 SA16G 14.8 GiB
  225. [    2.702353]  mmcblk0: p1 p2
  226. [    2.708919] asoc: sgtl5000 <-> imx-ssi.1 mapping ok
  227. [    2.716208] asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok
  228. [    2.726630] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
  229. [    2.733418] ALSA device list:
  230. [    2.736389]   #0: sgtl5000-audio
  231. [    2.739616]   #1: imx-spdif
  232. [    2.742428]   #2: imx-hdmi-soc
  233. [    2.745975] TCP cubic registered
  234. [    2.749205] NET: Registered protocol family 17
  235. [    2.755395] Bluetooth: RFCOMM socket layer initialized
  236. [    2.762187] Bluetooth: RFCOMM ver 1.11
  237. [    2.765937] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  238. [    2.771298] Bluetooth: BNEP filters: multicast
  239. [    2.775754] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  240. [    2.781832] lib80211: common routines for IEEE802.11 drivers
  241. [    2.789154] Registering the dns_resolver key type
  242. [    2.796287] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  243. [    2.804011] ThumbEE CPU extension supported.
  244. [    2.814005] Bus freq driver module loaded
  245. [    2.818041] Bus freq driver Enabled
  246. [    2.823487] mxc_dvfs_core_probe
  247. [    2.826887] DVFS driver module loaded
  248. [    2.831638] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  249. [    2.867387] EXT3-fs: barriers not enabled
  250. [    2.881442] kjournald starting.  Commit interval 5 seconds
  251. [    3.005994] mmc1: queuing unknown CIS tuple 0x80 (50 bytes)
  252. [    3.121617] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
  253. [    3.153501] mmc1: queuing unknown CIS tuple 0x80 (4 bytes)
  254. [    3.171902] EXT3-fs (mmcblk0p2): using internal journal
  255. [    3.177153] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
  256. [    3.185518] VFS: Mounted root (ext3 filesystem) on device 179:2.
  257. [    3.207443] devtmpfs: mounted
  258. [    3.210464] Freeing init memory: 180K
  259. [    3.282522] Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
  260. [    3.295054] [<c0041f3c>] (unwind_backtrace+0x0/0xf4) from [<c04aff04>] (panic+0x84/0x198)
  261. [    3.303266] [<c04aff04>] (panic+0x84/0x198) from [<c04af89c>] (cpu_has_aliasing_icache.part.3+0x0/0x3c)
  262. [    3.312686] CPU1: stopping
  263. [    3.315412] [<c0041f3c>] (unwind_backtrace+0x0/0xf4) from [<c0035338>] (do_IPI+0x144/0x154)
  264. [    3.323777] [<c0035338>] (do_IPI+0x144/0x154) from [<c003a9cc>] (__irq_svc+0x4c/0xe8)
  265. [    3.331609] Exception stack(0xe2061f68 to 0xe2061fb0)
  266. [    3.336664] 1f60:                   00000000 a0000093 00000001 00000001 00000000 00000000
  267. [    3.344845] 1f80: b95ed580 00000000 cc010568 c06a4cb8 00000000 00000000 00000020 e2061fb0
  268. [    3.353025] 1fa0: c008b5d0 c0097e9c 20000013 ffffffff
  269. [    3.358086] [<c003a9cc>] (__irq_svc+0x4c/0xe8) from [<c0097e9c>] (tick_nohz_restart_sched_tick+0x1d8/0x1e8)
  270. [    3.367834] [<c0097e9c>] (tick_nohz_restart_sched_tick+0x1d8/0x1e8) from [<c003bcd8>] (cpu_idle+0xc0/0x104)
  271. [    3.377592] [<c003bcd8>] (cpu_idle+0xc0/0x104) from [<104ac994>] (0x104ac994)
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top