Guest User

Armbian kernel in panic on loboris OS image :)

a guest
Jun 12th, 2016
196
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. HELLO! BOOT0 is starting!
  2. boot0 version : 4.0.0
  3. fel_flag = 0x00000000
  4. rtc[0] value = 0x00000000
  5. rtc[1] value = 0x00000000
  6. rtc[2] value = 0x00000000
  7. rtc[3] value = 0x00000000
  8. rtc[4] value = 0x00000000
  9. rtc[5] value = 0x00000000
  10. rtc[6] value = 0x00000000
  11. rtc[7] value = 0x00000000
  12. DRAM DRIVE INFO: V0.8
  13. DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
  14. DRAM CLK = 672 MHz
  15. DRAM zq value: 003b3bfb
  16. READ DQS LCDL = 001e1e1f
  17. DRAM SIZE =1024 M
  18. odt delay
  19. dram size =1024
  20. card boot number = 0
  21. card no is 0
  22. sdcard 0 line count 4
  23. [mmc]: mmc driver ver 2014-12-10 21:20:39
  24. [mmc]: ***Try SD card 0***
  25. [mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  26. [mmc]: vendor: Man 00035344 Snr 437635a9
  27. [mmc]: product: SL08G
  28. [mmc]: revision: 8.0
  29. [mmc]: ***SD/MMC 0 init OK!!!***
  30. sdcard 0 init ok
  31. The size of uboot is 000dc000.
  32. sum=ede66ee7
  33. src_sum=ede66ee7
  34. Succeed in loading uboot from sdmmc flash.
  35. Ready to disable icache.
  36. Jump to secend Boot.
  37. SUNXI_NORMAL_MODE
  38. [ 0.374]e mode
  39.  
  40. U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology
  41.  
  42. [ 0.382]version: 1.1.0
  43. normal mode
  44. [ 0.389]pmbus: ready
  45. not set main pmu id
  46. axp_probe error
  47. [ 0.404]PMU: pll1 1200 Mhz,PLL6=600 Mhz
  48. AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
  49. sid read already
  50. fel key new mode
  51. run key detect
  52. no key found
  53. no key input
  54. dram_para_set start
  55. dram_para_set end
  56. normal mode
  57. [ 0.434]DRAM: 1 GiB
  58. relocation Offset is: 35af9000
  59. [box standby] read rtc = 0x0
  60. [box_start_os] mag be start_type no use
  61. user_gpio config
  62. user_gpio ok
  63. gic: normal or no secure os mode
  64. workmode = 0
  65. MMC: 0
  66. [ 0.509][mmc]: mmc driver ver 2014-12-10 9:23:00
  67. [ 0.514][mmc]: get sdc_phy_wipe fail.
  68. [ 0.518][mmc]: get sdc0 sdc_erase fail.
  69. [ 0.522][mmc]: get sdc_f_max fail,use default 50000000Hz
  70. [ 0.527][mmc]: get sdc_ex_dly_used fail,use default dly
  71. [ 0.533][mmc]: SUNXI SD/MMC: 0
  72. [ 0.546][mmc]: *Try SD card 0*
  73. [ 0.595][mmc]: CID 0x3534453 0x4c303847 0x80437635 0xa900f78f
  74. [ 0.600][mmc]: mmc clk 50000000
  75. [ 0.604][mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  76. [ 0.608][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
  77. [ 0.614][mmc]: ***SD/MMC 0 init OK!!!***
  78. [ 0.618][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
  79. [ 0.624][mmc]: secure_feature 0x0
  80. [ 0.627][mmc]: secure_removal_type 0x0
  81. [ 0.631]sunxi flash init ok
  82. script config pll_de to 864 Mhz
  83. Not Found clk pll_video1 in script
  84. script config pll_video to 297 Mhz
  85. [boot]disp_init_tv
  86. [DISP_TV] disp_init_tv enter g_tv_used
  87. screen 0 do not support TV TYPE!
  88. [BOOOT_DISP_TV] disp tv device_registered
  89. unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
  90. enable power vcc-hdmi-18, ret=-1
  91. DRV_DISP_Init end
  92. boot_disp.auto_hpd=1
  93. auto hpd check has 0 times!
  94. [disk_read_fs] no the partition
  95. error: open disp_rsl.fex, maybe it is not exist
  96. not support this mode[4], use inline mode[4]
  97. attched ok, mgr0<-->device0, type=4, mode=4----
  98. ready to set mode
  99. [ 1.241]finally, output_type=0x4, output_mode=0x4, screen_id=0x0, disp_para=0x404
  100. fail to find part named env
  101. Using default environment
  102.  
  103. In: serial
  104. Out: serial
  105. Err: serial
  106. --------fastboot partitions--------
  107. mbr not exist
  108. base bootcmd=run setargs_mmc boot_normal
  109. bootcmd set setargs_mmc
  110. key 0
  111. cant find rcvy value
  112. cant find fstbt value
  113. no misc partition is found
  114. to be run cmd=run setargs_mmc boot_normal
  115. [ 1.279][mmc]: MMC Device 2 not found
  116. [ 1.282][mmc]: Can not find mmc dev
  117. [ 1.286][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
  118. sunxi_secstorage_read fail
  119. get secure storage map err
  120. the private part isn't exist
  121. WORK_MODE_BOOT
  122. adver not need show
  123. sunxi_bmp_logo_display
  124. [disk_read_fs] no the partition
  125. error: open bootlogo.bmp, maybe it is not exist
  126. sunxi bmp info error : unable to open logo file bootlogo.bmp
  127. [ 1.319]Hit any key to stop autoboot: 0
  128. [ 4.588][mmc]: blkcnt should not be 0
  129. [ 4.813][mmc]: blkcnt should not be 0
  130. ## Booting kernel from Legacy Image at 40007800 ...
  131. Image Name: Armbian sun8i-3.4.112
  132. Image Type: ARM Linux Kernel Image (uncompressed)
  133. Data Size: 5064800 Bytes = 4.8 MiB
  134. Load Address: 40008000
  135. Entry Point: 40008000
  136. Verifying Checksum ... OK
  137. Loading Kernel Image ... OK
  138. OK
  139. [ 4.918][mmc]: MMC Device 2 not found
  140. [ 4.922][mmc]: mmc not find,so not exit
  141. [ 4.926]
  142. Starting kernel ...
  143.  
  144. [sun8i_fixup]: From boot, get meminfo:
  145. Start: 0x40000000
  146. Size: 1024MB
  147. ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
  148. ion_reserve_select: ion chipid [0x2c00081!
  149. ion_reserve_common: ion reserve: [0x50000000, 0x60000000]!
  150. [ 0.000000] Booting Linux on physical CPU 0
  151. [ 0.000000] Initializing cgroup subsys cpuset
  152. [ 0.000000] Initializing cgroup subsys cpu
  153. [ 0.000000] Linux version 3.4.112-sun8i (root@armbian) (gcc version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #8 SMP PREEMPT Sat Jun6
  154. [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  155. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  156. [ 0.000000] Machine: sun8i
  157. [ 0.000000] cma: CMA: reserved 256 MiB at 50000000
  158. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  159. [ 0.000000] On node 0 totalpages: 262144
  160. [ 0.000000] free_area_init_node: node 0, pgdat c0a35380, node_mem_map c0b76000
  161. [ 0.000000] Normal zone: 1710 pages used for memmap
  162. [ 0.000000] Normal zone: 0 pages reserved
  163. [ 0.000000] Normal zone: 192850 pages, LIFO batch:31
  164. [ 0.000000] HighMem zone: 594 pages used for memmap
  165. [ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
  166. [ 0.000000] script_init enter!
  167. [ 0.000000] script_init exit!
  168. [ 0.000000] PERCPU: Embedded 8 pages/cpu @c1491000 s11968 r8192 d12608 u32768
  169. [ 0.000000] pcpu-alloc: s11968 r8192 d12608 u32768 alloc=8*4096
  170. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  171. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259840
  172. [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 init=/init loglevel=8 partitions=
  173. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  174. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  175. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  176. [ 0.000000] allocated 2097152 bytes of page_cgroup
  177. [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
  178. [ 0.000000] Memory: 1024MB = 1024MB total
  179. [ 0.000000] Memory: 761632k/761632k available, 286944k reserved, 270336K highmem
  180. [ 0.000000] Virtual kernel memory layout:
  181. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  182. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  183. [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
  184. [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
  185. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  186. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  187. [ 0.000000] .text : 0xc0008000 - 0xc096bf2c (9616 kB)
  188. [ 0.000000] .init : 0xc096c000 - 0xc09beec0 ( 332 kB)
  189. [ 0.000000] .data : 0xc09c0000 - 0xc0a3a1d0 ( 489 kB)
  190. [ 0.000000] .bss : 0xc0a3a984 - 0xc0b75bd0 (1261 kB)
  191. [ 0.000000] Preemptible hierarchical RCU implementation.
  192. [ 0.000000] Additional per-CPU info printed with stalls.
  193. [ 0.000000] NR_IRQS:544
  194. [ 0.000000] Architected local timer running at 24.00MHz.
  195. [ 0.000000] Switching to timer-based delay loop
  196. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  197. [ 0.000000] Console: colour dummy device 80x30
  198. [ 0.000181] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
  199. [ 0.000202] pid_max: default: 32768 minimum: 301
  200. [ 0.000485] Mount-cache hash table entries: 512
  201. [ 0.001305] Initializing cgroup subsys cpuacct
  202. [ 0.001318] Initializing cgroup subsys memory
  203. [ 0.001357] Initializing cgroup subsys devices
  204. [ 0.001368] Initializing cgroup subsys freezer
  205. [ 0.001377] Initializing cgroup subsys blkio
  206. [ 0.001397] Initializing cgroup subsys perf_event
  207. [ 0.001467] CPU: Testing write buffer coherency: ok
  208. [ 0.001505] ftrace: allocating 25980 entries in 77 pages
  209. [ 0.030265] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  210. [ 0.030280] [sunxi_smp_prepare_cpus] enter
  211. [ 0.030316] Setting up static identity map for 0x4069fa60 - 0x4069fab8
  212. [ 0.031138] CPU1: Booted secondary processor
  213. [ 0.031138] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  214. [ 0.031269] CPU2: Booted secondary processor
  215. [ 0.031269] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
  216. [ 0.040152] CPU3: Booted secondary processor
  217. [ 0.040152] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
  218. [ 0.040269] Brought up 4 CPUs
  219. [ 0.040269] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
  220. [ 0.040778] devtmpfs: initialized
  221. [ 0.043023] wakeup src cnt is : 1.
  222. [ 0.043034] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
  223. [ 0.043043] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
  224. [ 0.043053] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
  225. [ 0.043062] sunxi pm init
  226. [ 0.043178] pinctrl core: initialized pinctrl subsystem
  227. [ 0.056953] NET: Registered protocol family 16
  228. [ 0.057557] DMA: preallocated 2048 KiB pool for atomic coherent allocations
  229. [ 0.057557] script_sysfs_init success
  230. [ 0.057557] sunxi_dump_init success
  231. [ 0.057557] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
  232. [ 0.057557] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
  233. [ 0.057557] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  234. [ 0.057557] hw-breakpoint: maximum watchpoint size is 8 bytes.
  235. [ 0.057557] script config pll_video to 297 Mhz
  236. [ 0.057557] script config pll_de to 864 Mhz
  237. [ 0.057557] script config pll_ve to 402 Mhz
  238. [ 0.057557] sunxi_default_clk_init
  239. [ 0.057557] try to set pll6ahb1 to 200000000
  240. [ 0.057557] try to set ahb clk source to pll6ahb1
  241. [ 0.057557] set ahb clk source to pll6ahb1
  242. [ 0.057557] try to set ahb1 to 200000000
  243. [ 0.057557] try to set apb1 to 100000000
  244. [ 0.061051] bio: create slab <bio-0> at 0
  245. [ 0.061051] [ARISC] :sunxi-arisc driver v1.04
  246. [ 0.074557] [ARISC] :arisc version: [v0.1.58]
  247. [ 0.158719] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
  248. [ 0.160380] SCSI subsystem initialized
  249. [ 0.160550] usbcore: registered new interface driver usbfs
  250. [ 0.160612] usbcore: registered new interface driver hub
  251. [ 0.170037] usbcore: registered new device driver usb
  252. [ 0.170130] twi_chan_cfg()340 - [twi0] has no twi_regulator.
  253. [ 0.170140] twi_chan_cfg()340 - [twi1] has no twi_regulator.
  254. [ 0.170150] twi_chan_cfg()340 - [twi2] has no twi_regulator.
  255. [ 0.170717] Linux video capture interface: v2.00
  256. [ 0.170905] Advanced Linux Sound Architecture Driver Version 1.0.25.
  257. [ 0.171536] cfg80211: Calling CRDA to update world regulatory domain
  258. [ 0.171584] Switching to clocksource arch_sys_counter
  259. [ 0.182017] FS-Cache: Loaded
  260. [ 0.182268] CacheFiles: Loaded
  261. [ 0.191696] NET: Registered protocol family 2
  262. [ 0.201233] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  263. [ 0.201738] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  264. [ 0.203218] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  265. [ 0.204105] TCP: Hash tables configured (established 131072 bind 65536)
  266. [ 0.204114] TCP: reno registered
  267. [ 0.204126] UDP hash table entries: 512 (order: 2, 16384 bytes)
  268. [ 0.204157] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  269. [ 0.204452] NET: Registered protocol family 1
  270. [ 0.204792] RPC: Registered named UNIX socket transport module.
  271. [ 0.204802] RPC: Registered udp transport module.
  272. [ 0.204809] RPC: Registered tcp transport module.
  273. [ 0.204816] RPC: Registered tcp NFSv4.1 backchannel transport module.
  274. [ 0.205169] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
  275. [ 0.205261] sunxi_reg_init enter
  276. [ 0.205931] audit: initializing netlink socket (disabled)
  277. [ 0.205964] type=2000 audit(0.200:1): initialized
  278. [ 0.206883] highmem bounce pool size: 64 pages
  279. [ 0.207642] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  280. [ 0.207808] misc fatfs initialized
  281. [ 0.208411] NFS: Registering the id_resolver key type
  282. [ 0.208741] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  283. [ 0.208752] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  284. [ 0.209410] NTFS driver 2.1.30 [Flags: R/W].
  285. [ 0.209666] fuse init (API version 7.18)
  286. [ 0.210381] Btrfs loaded
  287. [ 0.210404] msgmni has been set to 1471
  288. [ 0.211626] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  289. [ 0.211642] io scheduler noop registered
  290. [ 0.211650] io scheduler deadline registered
  291. [ 0.211709] io scheduler cfq registered (default)
  292. [ 0.212083] [DISP]disp_module_init
  293. [ 0.212349] cmdline,init_disp=
  294. [ 0.212375] cmdline,disp=
  295. [ 0.225274] [DISP] Fb_map_kernel_logo,line:932:Fb_map_kernel_logo failed!
  296. [ 0.255421] Console: switching to colour frame buffer device 240x67
  297. [ 0.286246] [DISP]disp_module_init finish
  298. [ 0.286446] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
  299. [ 0.286462] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
  300. [ 0.286473] sw_uart_get_devinfo()1503 - uart3 has no uart_regulator.
  301. [ 0.286925] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
  302. [ 0.286936] sw_uart_pm()890 - uart0 clk is already enable
  303. [ 0.286951] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
  304. [ 0.382533] console [ttyS0] enabled
  305. [ 1.147047] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
  306. [ 1.147373] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI
  307. [ 1.147851] sunxi_cmatest_init enter
  308. [ 1.147890] sunxi_cmatest_init success
  309. [ 1.151570] brd: module loaded
  310. [ 1.154900] loop: module loaded
  311. [ 1.193783] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
  312. [ 1.229095] sunxi_spi_chan_cfg()1376 - [spi-1] has no spi_regulator.
  313. [ 1.236714] spi spi0: master is unqueued, this is deprecated
  314. [ 1.243290] tun: Universal TUN/TAP device driver, 1.6
  315. [ 1.248889] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  316. [ 1.256590] PPP generic driver version 2.4.2
  317. [ 1.261494] PPP BSD Compression module registered
  318. [ 1.266708] PPP Deflate Compression module registered
  319. [ 1.273012] PPP MPPE Compression module registered
  320. [ 1.278329] NET: Registered protocol family 24
  321. [ 1.283320] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  322. [ 1.310630] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  323. [ 1.319524] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
  324. [ 1.328446] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
  325. [ 1.350026] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
  326. [ 1.357091] hub 1-0:1.0: USB hub found
  327. [ 1.361282] hub 1-0:1.0: 1 port detected
  328. [ 1.385947] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  329. [ 1.394849] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
  330. [ 1.403672] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
  331. [ 1.430025] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
  332. [ 1.437043] hub 2-0:1.0: USB hub found
  333. [ 1.441224] hub 2-0:1.0: 1 port detected
  334. [ 1.445874] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  335. [ 1.472783] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  336. [ 1.481299] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 3
  337. [ 1.489712] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
  338. [ 1.554450] hub 3-0:1.0: USB hub found
  339. [ 1.558617] hub 3-0:1.0: 1 port detected
  340. [ 1.583273] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
  341. [ 1.591786] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 4
  342. [ 1.600215] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
  343. [ 1.664490] hub 4-0:1.0: USB hub found
  344. [ 1.668654] hub 4-0:1.0: 1 port detected
  345. [ 1.673322] Initializing USB Mass Storage driver...
  346. [ 1.678857] usbcore: registered new interface driver usb-storage
  347. [ 1.685533] USB Mass Storage support registered.
  348. [ 1.690704] usbcore: registered new interface driver ums-alauda
  349. [ 1.697297] usbcore: registered new interface driver ums-cypress
  350. [ 1.704001] usbcore: registered new interface driver ums-datafab
  351. [ 1.710703] usbcore: registered new interface driver ums_eneub6250
  352. [ 1.717584] usbcore: registered new interface driver ums-freecom
  353. [ 1.724291] usbcore: registered new interface driver ums-isd200
  354. [ 1.730905] usbcore: registered new interface driver ums-jumpshot
  355. [ 1.737692] usbcore: registered new interface driver ums-karma
  356. [ 1.744205] usbcore: registered new interface driver ums-onetouch
  357. [ 1.751019] usbcore: registered new interface driver ums-realtek
  358. [ 1.757710] usbcore: registered new interface driver ums-sddr09
  359. [ 1.764319] usbcore: registered new interface driver ums-sddr55
  360. [ 1.770975] usbcore: registered new interface driver ums-usbat
  361. [ 1.777711] file system registered
  362. [ 1.783041] android_usb gadget: Mass Storage Function, version: 2009/09/11
  363. [ 1.790694] android_usb gadget: Number of LUNs=3
  364. [ 1.795813] lun0: LUN: removable file: (no medium)
  365. [ 1.801232] lun1: LUN: removable file: (no medium)
  366. [ 1.806639] lun2: LUN: removable file: (no medium)
  367. [ 1.812351] android_usb gadget: android_usb ready
  368. [ 1.817747] uinput result 0 , vmouse_init
  369. [ 1.822894] mousedev: PS/2 mouse device common for all mice
  370. [ 1.829260] sunxikbd_init failed.
  371. [ 1.833465] ls_fetch_sysconfig_para: type err device_used = -1073060236.
  372. [ 1.841114] =========script_get_err============
  373. [ 1.846134] ltr_init: ls_fetch_sysconfig_para err.
  374. [ 1.851739] [RTC] WARNING: Rtc time will be wrong!!
  375. [ 1.857145] [RTC] WARNING: use *internal OSC* as clock source
  376. [ 1.863763] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
  377. [ 1.871148] i2c /dev entries driver
  378. [ 1.875344] IR RC5(x) protocol handler initialized
  379. [ 1.880777] sunxi cedar version 0.1
  380. [ 1.884763] [cedar]: install start!!!
  381. [ 1.888981] [cedar]: install end!!!
  382. [ 1.893083] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
  383. [ 1.902428] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
  384. [ 1.911761] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1a)
  385. [ 1.921093] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
  386. [ 1.930424] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2a)
  387. [ 1.939742] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2b)
  388. [ 1.949073] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
  389. [ 1.958404] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4d)
  390. [ 1.967735] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4e)
  391. [ 1.977097] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x18)
  392. [ 1.986456] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x19)
  393. [ 1.995814] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x1a)
  394. [ 2.005179] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x29)
  395. [ 2.014538] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2a)
  396. [ 2.023896] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2b)
  397. [ 2.033254] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4c)
  398. [ 2.042639] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4d)
  399. [ 2.051996] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4e)
  400. [ 2.061177] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
  401. [ 2.068257] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
  402. [ 2.079383] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
  403. [ 2.086833] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
  404. [ 2.093023] timeout_to_interv, line 167
  405. [ 2.097271] interv_to_timeout, line 189
  406. [ 2.101533] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
  407. [ 2.110959] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
  408. [ 2.120410] calibrat: max_cpufreq 1200Mhz Type 0!
  409. [ 2.125960] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.111 2015-4-13 15:24) Compiled in Jun 11 2016 at 16:43:20
  410. [ 2.137380] [mmc]: get mmc0's sdc_power is null!
  411. [ 2.142527] [mmc]: get mmc1's sdc_power is null!
  412. [ 2.147644] [mmc]: get mmc1's 2xmode ok, val = 1
  413. [ 2.152777] [mmc]: get mmc1's ddrmode ok, val = 1
  414. [ 2.157997] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
  415. [ 2.166024] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  416. [ 2.179024] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  417. [ 2.191542] no blue_led, ignore it!
  418. [ 2.195587] Registered led device: red_led
  419. [ 2.200243] Registered led device: green_led
  420. [ 2.204981] no led_0, ignore it!
  421. [ 2.208555] no led_1, ignore it!
  422. [ 2.212144] no led_2, ignore it!
  423. [ 2.215718] no led_3, ignore it!
  424. [ 2.219291] no led_4, ignore it!
  425. [ 2.222897] no led_5, ignore it!
  426. [ 2.226470] no led_6, ignore it!
  427. [ 2.230057] no led_7, ignore it!
  428. [ 2.234276] usbcore: registered new interface driver usbhid
  429. [ 2.240477] usbhid: USB HID core driver
  430. [ 2.247842] asoc: sndcodec <-> sunxi-codec mapping ok
  431. [ 2.254204] [DAUDIO]sunxi-daudio cannot find any using configuration for controllers, return directly!
  432. [ 2.264709] [I2S]snddaudio cannot find any using configuration for controllers, return directly!
  433. [ 2.274471] [DAUDIO0] driver not init,just return.
  434. [ 2.282330] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
  435. [ 2.289188] oprofile: using arm/armv7-ca7
  436. [ 2.293811] u32 classifier
  437. [ 2.296809] Actions configured
  438. [ 2.300746] IPv4 over IPv4 tunneling driver
  439. [ 2.305870] TCP: bic registered
  440. [ 2.309352] TCP: cubic registered
  441. [ 2.313048] TCP: westwood registered
  442. [ 2.317009] TCP: highspeed registered
  443. [ 2.321078] TCP: hybla registered
  444. [ 2.324749] TCP: htcp registered
  445. [ 2.328323] TCP: vegas registered
  446. [ 2.332013] TCP: veno registered
  447. [ 2.335588] TCP: scalable registered
  448. [ 2.339548] TCP: lp registered
  449. [ 2.342941] TCP: yeah registered
  450. [ 2.346515] TCP: illinois registered
  451. [ 2.350486] Initializing XFRM netlink socket
  452. [ 2.355393] NET: Registered protocol family 10
  453. [ 2.361270] NET: Registered protocol family 17
  454. [ 2.366214] NET: Registered protocol family 15
  455. [ 2.371198] Registering the dns_resolver key type
  456. [ 2.376564] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  457. [ 2.385087] ThumbEE CPU extension supported.
  458. [ 2.389831] Registering SWP/SWPB emulation handler
  459. [ 2.395629] registered taskstats version 1
  460. [ 2.400571] cmdline,disp=
  461. [ 2.403502] [HDMI] power vcc-hdmi-18
  462. [ 2.438147] ths_fetch_sysconfig_para: type err device_used = 1.
  463. [ 2.446125] CPU Budget:Register notifier
  464. [ 2.450540] CPU Budget:register Success
  465. [ 2.454796] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
  466. [ 2.467340] [rf_pm]: module power0 name vcc-wifi-33
  467. [ 2.472792] [rf_pm]: Did not config module_power1 in sys_config
  468. [ 2.479349] [rf_pm]: Did not config module_power2 in sys_config
  469. [ 2.485944] [rf_pm]: Did not config module_power3 in sys_config
  470. [ 2.492521] [rf_pm]: mod has no chip_en gpio
  471. [ 2.497253] [rf_pm]: failed to fetch lpo_use_apclk
  472. [ 2.502574] [rf_pm]: regulator on.
  473. [ 2.506579] [wifi_pm]: wifi gpio init is OK !!
  474. [ 2.511565] [rfkill]: init no bt used in configuration
  475. [ 2.517263] ALSA device list:
  476. [ 2.520563] #0: audiocodec
  477. [ 2.523752] #1: sndhdmi
  478. [ 2.527178] VFS: Cannot open root device "mmcblk0p2" or unknown-block(0,0): error -6
  479. [ 2.535810] Please append a correct "root=" boot option; here are the available partitions:
  480. [ 2.545131] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  481. [ 2.554304] CPU1: stopping
  482. [ 2.557333] [<c0016a20>] (unwind_backtrace+0x0/0xe8) from [<c0695ad0>] (dump_stack+0x20/0x24)
  483. [ 2.564301] [<c0695ad0>] (dump_stack+0x20/0x24) from [<c0014170>] (handle_IPI+0x114/0x298)
  484. [ 2.564301] [<c0014170>] (handle_IPI+0x114/0x298) from [<c0008554>] (gic_handle_irq+0x64/0x6c)
  485. [ 2.564301] [<c0008554>] (gic_handle_irq+0x64/0x6c) from [<c000db40>] (__irq_svc+0x40/0x74)
  486. [ 2.564301] Exception stack(0xef0c1f68 to 0xef0c1fb0)
  487. [ 2.564301] 1f60: c1499b38 c09e224c 0000000f 00000000 ef0c0000 00000001
  488. [ 2.564301] 1f80: ef0c0000 c0a3ad24 4000406a 410fc075 00000000 ef0c1fbc ef0c1fc0 ef0c1fb0
  489. [ 2.564301] 1fa0: c000f2d8 c000f2dc 60000013 ffffffff
  490. [ 2.564301] [<c000db40>] (__irq_svc+0x40/0x74) from [<c000f2dc>] (default_idle+0x34/0x3c)
  491. [ 2.564301] [<c000f2dc>] (default_idle+0x34/0x3c) from [<c000f694>] (cpu_idle+0xa8/0xf4)
  492. [ 2.564301] [<c000f694>] (cpu_idle+0xa8/0xf4) from [<c06929dc>] (secondary_start_kernel+0x108/0x12c)
  493. [ 2.564301] [<c06929dc>] (secondary_start_kernel+0x108/0x12c) from [<40691ff4>] (0x40691ff4)
  494. [ 2.564301] CPU3: stopping
  495. [ 2.564301] [<c0016a20>] (unwind_backtrace+0x0/0xe8) from [<c0695ad0>] (dump_stack+0x20/0x24)
  496. [ 2.564301] [<c0695ad0>] (dump_stack+0x20/0x24) from [<c0014170>] (handle_IPI+0x114/0x298)
  497. [ 2.564301] [<c0014170>] (handle_IPI+0x114/0x298) from [<c0008554>] (gic_handle_irq+0x64/0x6c)
  498. [ 2.564301] [<c0008554>] (gic_handle_irq+0x64/0x6c) from [<c000db40>] (__irq_svc+0x40/0x74)
  499. [ 2.564301] Exception stack(0xef0fff68 to 0xef0fffb0)
  500. [ 2.564301] ff60: c14a9b38 c09e224c 0000000f 00000000 ef0fe000 00000003
  501. [ 2.564301] ff80: ef0fe000 c0a3ad24 4000406a 410fc075 00000000 ef0fffbc ef0fffc0 ef0fffb0
  502. [ 2.564301] ffa0: c000f2d8 c000f2dc 60000013 ffffffff
  503. [ 2.564301] [<c000db40>] (__irq_svc+0x40/0x74) from [<c000f2dc>] (default_idle+0x34/0x3c)
  504. [ 2.564301] [<c000f2dc>] (default_idle+0x34/0x3c) from [<c000f694>] (cpu_idle+0xa8/0xf4)
  505. [ 2.564301] [<c000f694>] (cpu_idle+0xa8/0xf4) from [<c06929dc>] (secondary_start_kernel+0x108/0x12c)
  506. [ 2.564301] [<c06929dc>] (secondary_start_kernel+0x108/0x12c) from [<40691ff4>] (0x40691ff4)
  507. [ 2.564300] CPU0: stopping
  508. [ 2.564300] [<c0016a20>] (unwind_backtrace+0x0/0xe8) from [<c0695ad0>] (dump_stack+0x20/0x24)
  509. [ 2.564300] [<c0695ad0>] (dump_stack+0x20/0x24) from [<c0014170>] (handle_IPI+0x114/0x298)
  510. [ 2.564300] [<c0014170>] (handle_IPI+0x114/0x298) from [<c0008554>] (gic_handle_irq+0x64/0x6c)
  511. [ 2.564300] [<c0008554>] (gic_handle_irq+0x64/0x6c) from [<c000db40>] (__irq_svc+0x40/0x74)
  512. [ 2.564300] Exception stack(0xc09c1f20 to 0xc09c1f68)
  513. [ 2.564300] 1f20: c1491b38 c09e224c 0000000f 00000000 c09c0000 c0a5d4c8 00000001 ffffffff
  514. [ 2.564300] 1f40: c148e240 c099b58c 00000000 c09c1f74 c09c1f78 c09c1f68 c000f2d8 c000f2dc
  515. [ 2.564300] 1f60: 60000013 ffffffff
  516. [ 2.564300] [<c000db40>] (__irq_svc+0x40/0x74) from [<c000f2dc>] (default_idle+0x34/0x3c)
  517. [ 2.564300] [<c000f2dc>] (default_idle+0x34/0x3c) from [<c000f694>] (cpu_idle+0xa8/0xf4)
  518. [ 2.564300] [<c000f694>] (cpu_idle+0xa8/0xf4) from [<c068d608>] (rest_init+0x9c/0xb8)
  519. [ 2.564300] [<c068d608>] (rest_init+0x9c/0xb8) from [<c096c8a8>] (start_kernel+0x2f4/0x354)
  520. [ 2.564300] [<c096c8a8>] (start_kernel+0x2f4/0x354) from [<40008044>] (0x40008044)
  521. [ 2.555079] [hotplug]: cpu(2) try to kill cpu(0)
  522. [ 2.555079] [hotplug]: try to kill cpu:0 failed!
  523. [ 2.555079] [hotplug]: cpu(2) try to kill cpu(1)
  524. [ 2.555079] [hotplug]: try to kill cpu:1 failed!
  525. [ 2.555079] [hotplug]: cpu(2) try to kill cpu(3)
  526. [ 2.555079] [hotplug]: try to kill cpu:3 failed!
  527. [ 24.030010] ------------[ cut here ]------------
  528. [ 24.035137] WARNING: at kernel/watchdog.c:255 watchdog_timer_fn+0xf8/0x2a8()
  529. [ 24.040004] Watchdog detected hard LOCKUP on cpu 3
  530. [ 24.040004] Modules linked in:
  531. [ 24.040004] [<c0016a20>] (unwind_backtrace+0x0/0xe8) from [<c0695ad0>] (dump_stack+0x20/0x24)
  532. [ 24.040004] [<c0695ad0>] (dump_stack+0x20/0x24) from [<c0029720>] (warn_slowpath_common+0x5c/0x74)
  533. [ 24.040004] [<c0029720>] (warn_slowpath_common+0x5c/0x74) from [<c0029778>] (warn_slowpath_fmt+0x40/0x48)
  534. [ 24.040004] [<c0029778>] (warn_slowpath_fmt+0x40/0x48) from [<c00a2378>] (watchdog_timer_fn+0xf8/0x2a8)
  535. [ 24.040004] [<c00a2378>] (watchdog_timer_fn+0xf8/0x2a8) from [<c004de1c>] (__run_hrtimer+0xe4/0x260)
  536. [ 24.040004] [<c004de1c>] (__run_hrtimer+0xe4/0x260) from [<c004e98c>] (hrtimer_interrupt+0x14c/0x2a0)
  537. [ 24.040004] [<c004e98c>] (hrtimer_interrupt+0x14c/0x2a0) from [<c0014a14>] (arch_timer_handler+0x38/0x48)
  538. [ 24.040004] [<c0014a14>] (arch_timer_handler+0x38/0x48) from [<c00a61a4>] (handle_percpu_devid_irq+0xb4/0x180)
  539. [ 24.040004] [<c00a61a4>] (handle_percpu_devid_irq+0xb4/0x180) from [<c00a276c>] (generic_handle_irq+0x30/0x40)
  540. [ 24.040004] [<c00a276c>] (generic_handle_irq+0x30/+-----------------------------------+x8c/0xbc)
  541. [ 24.040004] [<c000ef54>] (handle_IRQ+0x8c/0xbc) fr| |0x6c)
  542. [ 24.040004] [<c000853c>] (gic_handle_irq+0x4c/0x6c| Cannot open /dev/cu.usbserial! |x74)
  543. [ 24.040004] Exception stack(0xef083e60 to 0xef083e| |
  544. [ 24.040004] 3e60: 00000000 00000000 fd640800 00000+-----------------------------------+18
  545. [ 24.040004] 3e80: 00000054 c0a0100c 066665b0 ef083ec4 ef083e90 ef083ea8 c037fbb4 c037fc04
  546. [ 24.040004] 3ea0: a0000113 ffffffff
  547. [ 24.040004] [<c000db40>] (__irq_svc+0x40/0x74) from [<c037fc04>] (__timer_delay+0x38/0x5c)
  548. [ 24.040004] [<c037fc04>] (__timer_delay+0x38/0x5c) from [<c037fc54>] (__timer_const_udelay+0x2c/0x34)
  549. [ 24.040004] [<c037fc54>] (__timer_const_udelay+0x2c/0x34) from [<c0695eb0>] (panic+0x19c/0x1c8)
  550. [ 24.040004] [<c0695eb0>] (panic+0x19c/0x1c8) from [<c096cf1c>] (mount_block_root+0x1d8/0x214)
  551. [ 24.040004] [<c096cf1c>] (mount_block_root+0x1d8/0x214) from [<c096d130>] (mount_root+0xf0/0x114)
  552. [ 24.040004] [<c096d130>] (mount_root+0xf0/0x114) from [<c096d2b4>] (prepare_namespace+0x160/0x1c0)
  553. [ 24.040004] [<c096d2b4>] (prepare_namespace+0x160/0x1c0) from [<c096cb10>] (kernel_init+0x208/0x254)
  554. [ 24.040004] [<c096cb10>] (kernel_init+0x208/0x254) from [<c000f1b0>] (kernel_thread_exit+0x0/0x8)
  555. [ 24.040004] ---[ end trace 74b6a862d3a3d5d8 ]---
RAW Paste Data

Adblocker detected! Please consider disabling it...

We've detected AdBlock Plus or some other adblocking software preventing Pastebin.com from fully loading.

We don't have any obnoxious sound, or popup ads, we actively block these annoying types of ads!

Please add Pastebin.com to your ad blocker whitelist or disable your adblocking software.

×