API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Dec 2nd, 2015
208
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 38.90 KB | None | 0 0
raw download clone embed print report
  1. TE: 34830
  2. sdio debug board detected
  3.  
  4. BL2 Built : 15:24:17, Oct 28 2015.
  5. gxb g5d0d038 - xiaobo.gu@droid05
  6.  
  7. Board ID = 1
  8. set vcck to 1100 mv
  9. set vddee to 1000 mv
  10. CPU clk: 1536MHz
  11. DDR channel setting: DDR0 Rank0+1 same
  12. DDR0: 1024MB(auto) @ 912MHz(2T)-13
  13. DataBus test pass!
  14. AddrBus test pass!
  15. NAND init
  16. Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x000000b0
  17. Load bl30 from NAND, src: 0x00010000, des: 0x01000000, size: 0x00009ef0
  18. Sending bl30........................................OK.
  19. Run bl30...
  20. Load bl301 from NAND, src: 0x0001c000, des: 0x01000000, size: 0x00001b20
  21. Wait bl30...Done
  22. Sending bl301.......OK.
  23. Run bl301...
  24. Load bl31 from NAND, src
  25. 0x00020000, des: 0x10100000, size: 0x00011130
  26.  
  27.  
  28.  
  29. --- UART initialized after reboot ---
  30.  
  31. [Reset cause: unknown]
  32.  
  33. [Image: unknown, amlogic_v1.1.3046-00db630 2015-10-28 15:24:31 xiaobo.gu@droid05]
  34.  
  35. bl30: cheLoad bl33 from NAND, src: 0x00034000, des: 0x01000000, size: 0x0009e250
  36. ck_permit, count is 1
  37.  
  38.  
  39. bl30: check_permit: ok!
  40.  
  41.  
  42. chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
  43.  
  44. [0.147870 Inits done]
  45.  
  46. secure task start!
  47. high task start!
  48. low task start!
  49. NOTICE: BL3-1: v1.0(debug):4d2e34d
  50. NOTICE: BL3-1: Built : 17:08:35, Oct 29 2015
  51. INFO: BL3-1: Initializing runtime services
  52. INFO: BL3-1: Preparing for EL3 exit to normal world
  53. INFO: BL3-1: Next image address = 0x1000000
  54. INFO: BL3-1: Next image spsr = 0x3c9
  55.  
  56.  
  57. U-Boot 2015.01-g190b6f8-dirty (Nov 05 2015 - 14:46:36)
  58.  
  59. DRAM: 1 GiB
  60. Relocation Offset is: 36ed5000
  61. register usb cfg[0][1] = 0000000037f627c0
  62. register usb cfg[0][2] = 0000000037f627e0
  63. register usb cfg[2][0] = 0000000037f62800
  64. vpu detect type: 5
  65. vpu clk_level = 7
  66. set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
  67. boot_device_flag : 1
  68. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
  69. init bus_cycle=6, bus_timing=8, system=5.0ns
  70. NAND device id: ad de 14 a7 42 4a ad de
  71. detect NAND device: E revision 1Ynm NAND 8GiB H27UCG8T2E
  72. new oob mode
  73. bus_c=6,bus_t=8,sys=4.0ns,T_REA=16,T_RHOH=15
  74. show_phydev_list
  75. 0: nfboot
  76. detect new nand here and new_type:6
  77. get def value at blk:8,page:2048
  78. outside dtb: 0000000000000000
  79. using dtb on nand
  80. amlnf_dtb_init_partitions: probe.
  81. NAND CKECK:arg ndtb: valid=1, blk=10, page=36
  82. start dts,buffer=0000000033ef3640,dt_addr=0000000033ef3640
  83. parts: 11
  84. 00: logo 0000000002000000 1
  85. 01: recovery 0000000002000000 1
  86. 02: rsv 0000000000800000 1
  87. 03: tee 0000000000800000 1
  88. 04: crypt 0000000002000000 1
  89. 05: misc 0000000002000000 1
  90. 06: instaboot 0000000020000000 1
  91. 07: boot 0000000002000000 1
  92. 08: system 0000000040000000 1
  93. 09: cache 0000000020000000 2
  94. 10: data ffffffffffffffff 4
  95. NAND CKECK:arg nbbt: valid=1, blk=4, page=0
  96. NAND CKECK:arg fbbt: valid=1, blk=5, page=0
  97. total_blk:52
  98. NAND CKECK:arg ncnf: valid=1, blk=7, page=0
  99. aml_key_init probe.
  100. total_blk:52
  101. NAND CKECK:arg nkey: valid=1, blk=6, page=54
  102. boot_device_flag 1
  103. total_blk:52
  104. NAND CKECK:arg nenv: valid=1, blk=11, page=108
  105. nfboot : 0x000000000000-0x000001000000 :partn=0:single_chip single_plane
  106. nfcache : 0x00000d000000-0x000026000000 :partn=1:single_chip multi_plane
  107. nfcode : 0x000033000000-0x000078000000 :partn=9:single_chip multi_plane
  108. nfdata : 0x0000ab000000-0x000155000000 :partn=1:single_chip multi_plane
  109. (nfboot) bad blks 0
  110. (nfcache) bad blks 0
  111. (nfcode) bad blks 0
  112. (nfdata) bad blks 0
  113. amlnf_logic_init() start
  114. (nfcache), size:26000000
  115. nftl version 1.01.001
  116. nftl start: size 76, free 12
  117. -blks(76), total_blocks(64)
  118. (nfcode), size:78000000
  119. nftl version 1.01.001
  120. nftl start: size 240, free 26
  121. -blks(240), total_blocks(214)
  122. all block full!!
  123. current block: 118
  124. amlnf_logic_init() done
  125. MMC: aml_priv->desc_buf = 0x0000000033f23590
  126. aml_priv->desc_buf = 0x0000000033f25720
  127. SDIO Port B: 0, SDIO Port C: 1
  128. uboot env amlnf_env_read : ####
  129. In: serial
  130. Out: serial
  131. Err: serial
  132. [store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
  133. cmd dtb_read:
  134. amlnf_dtb_read: ####
  135. 262144 bytes dtd_read : OK
  136. Net: Meson_Ethernet
  137. wipe_data=successful
  138. wipe_cache=successful
  139. upgrade_step=2
  140. reboot_mode=cold_boot
  141. hpd_state=1
  142. [CANVAS]addr=0x3f800000 width=3840, height=2160
  143.  
  144. [1080p50hz] is invalid for cvbs.
  145. set hdmitx VIC = 31
  146. config HPLL = 2970
  147. HPLL: 0xc800023d
  148. config HPLL done
  149. set_hpll_od3_clk_div[216] div = 6
  150. j = 9 vid_clk_div = 1
  151. hdmitx phy setting done
  152. hdmitx: set enc for VIC: 31
  153. enc_vpu_bridge_reset[977]
  154. amlkey_init() enter!
  155. [EFUSE_MSG]keynum is 4
  156. [KM]Error:f[key_manage_query_size]L504:key[usid] not programed yet
  157. [KM]Error:f[key_manage_query_size]L504:key[deviceid] not programed yet
  158. saradc - saradc sub-system
  159.  
  160. Usage:
  161. saradc saradc open <channel> - open a SARADC channel
  162. saradc close - close the SARADC
  163. saradc getval - get the value in current channel
  164. saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
  165.  
  166. key1 = ba45ff00
  167. key2 = f807fe01
  168. time_out = 2625a0
  169. ir init
  170. irkey - irkey key_value1 key_value2 time_value
  171.  
  172. Usage:
  173. irkey
  174. Enter USB burn
  175. Try connect time out 701, 700, 3830
  176. Hit any key to stop autoboot: 1  0
  177. ret = 1 .sdio debug board detected, sd card with 1bit mode
  178. [mmc_init] mmc init success
  179. Device: SDIO Port B
  180. Manufacturer ID: 74
  181. OEM: 4a60
  182. Name: USD
  183. Tran Speed: 25000000
  184. Rd Block Len: 512
  185. SD version 3.0
  186. High Capacity: Yes
  187. Capacity: 7.5 GiB
  188. Bus Width: 1-bit
  189. reading kernel.img
  190. 13395968 bytes read in 4359 ms (2.9 MiB/s)
  191. reading dtb.img
  192. 31763 bytes read in 15 ms (2 MiB/s)
  193. sd dtb.img loaded
  194. ee_gate_off ...
  195. ## Booting Android Image at 0x01080000 ...
  196. load dtb from 0x1000000 ......
  197. Loading Kernel Image ... OK
  198. kernel loaded at 0x01080000, end = 0x019eaad0
  199. Loading Ramdisk to 33b70000, end 33ec2b70 ... OK
  200. Loading Device Tree to 000000001fff5000, end 000000001ffffc12 ... OK
  201. signature:
  202. fdt_instaboot: get header err
  203.  
  204. Starting kernel ...
  205.  
  206. uboot time: 9943871 us
  207. [ 0.000000@0] Linux version 3.14.29 (amlinux@runorm.info) (gcc version 5.2.0 (Buildroot 2016.02-git-gc377240-dirty) ) #1 SMP Wed Dec 2 21:20:49 MSK 2015
  208. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  209. [ 0.000000@0] bootconsole [earlycon0] enabled
  210. [ 0.000000@0] secmon: share mem setup
  211. [ 0.000000@0] Reserved memory: initialized node linux,secmon, compatible id aml_secmon_memory
  212. [ 0.000000@0] __reserved_mem_alloc_size: linux,meson-fb
  213. [ 0.000000@0] fb: Reserved memory: created fb at 0x000000003e000000, size 32 MiB
  214. [ 0.000000@0] Reserved memory: initialized node linux,meson-fb, compatible id amlogic, fb-memory
  215. [ 0.000000@0] __reserved_mem_alloc_size: linux,di
  216. [ 0.000000@0] DI reserved memory: created CMA memory pool at 0x000000003c200000, size 30 MiB
  217. [ 0.000000@0] Reserved memory: initialized node linux,di, compatible id amlogic, di-mem
  218. [ 0.000000@0] __reserved_mem_alloc_size: linux,ion-dev
  219. [ 0.000000@0] ppmgr share mem setup
  220. [ 0.000000@0] linux,ion-dev add multi user:ffffffc0019da1d8
  221. [ 0.000000@0] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
  222. [ 0.000000@0] __reserved_mem_alloc_size: linux,codec_mm_cma
  223. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000027800000, size 192 MiB
  224. [ 0.000000@0] Reserved memory: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
  225. [ 0.000000@0] __reserved_mem_alloc_size: linux,picdec
  226. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000037000000, size 48 MiB
  227. [ 0.000000@0] Reserved memory: initialized node linux,picdec, compatible id shared-dma-pool
  228. [ 0.000000@0] __reserved_mem_alloc_size: linux,codec_mm_reserved
  229. [ 0.000000@0] codec_mm:vdec: reserved mem setup
  230. [ 0.000000@0] Reserved memory: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
  231. [ 0.000000@0] cma: Reserved 8 MiB at 36800000
  232. [ 0.000000@0] psci: probing function IDs from device-tree
  233. [ 0.000000@0] PERCPU: Embedded 11 pages/cpu @ffffffc03a1b0000 s13632 r8192 d23232 u45056
  234. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 244696
  235. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.mem_address=0x20000000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3f800000,1080p60hz hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= androidboot.firstboot=1 boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 BOOT_IMAGE=kernel.img mac=D0:76:58:01:AF:75 console=tty0 consoleblank=0 systemd.show_status=auto ssh
  236. [ 0.000000@0] logo: osd1
  237. [ 0.000000@0] logo: loaded
  238. [ 0.000000@0] logo: 0x3f800000
  239. [ 0.000000@0] logo: 1080p60hz
  240. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  241. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  242. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  243. [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
  244. [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
  245. [ 0.000000@0] Memory: 574408K/996352K available (6429K kernel code, 454K rwdata, 2220K rodata, 529K init, 2471K bss, 421944K reserved)
  246. [ 0.000000@0] Virtual kernel memory layout:
  247. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  248. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8041180000 ( 17 MB)
  249. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  250. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc03e000000 ( 992 MB)
  251. [ 0.000000@0] .init : 0xffffffc0018f4000 - 0xffffffc001978540 ( 530 kB)
  252. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc0018f3444 ( 8654 kB)
  253. [ 0.000000@0] .data : 0xffffffc001979000 - 0xffffffc0019eaac0 ( 455 kB)
  254. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
  255. [ 0.000000@0] Hierarchical RCU implementation.
  256. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  257. [ 0.000000@0] CONFIG_RCU_FANOUT set to non-default value of 32
  258. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  259. [ 0.000005@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483648000ns
  260. [ 0.007537@0] mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff8000008994
  261. [ 0.014385@0] local timer MESON TIMER-G mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000a998
  262. [ 0.023463@0] local timer MESON TIMER-H mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000c99c
  263. [ 0.032564@0] local timer MESON TIMER-I mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000e9a0
  264. [ 0.041656@0] Switching to timer-based delay loop
  265. [ 0.046578@0] Console: colour dummy device 80x25
  266. [ 0.051016@0] console [tty0] enabled
  267. [ 0.054605@0] bootconsole [earlycon0] disabled
  268. [ 0.000000@0] Linux version 3.14.29 (amlinux@runorm.info) (gcc version 5.2.0 (Buildroot 2016.02-git-gc377240-dirty) ) #1 SMP Wed Dec 2 21:20:49 MSK 2015
  269. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  270. [ 0.000000@0] bootconsole [earlycon0] enabled
  271. [ 0.000000@0] secmon: share mem setup
  272. [ 0.000000@0] Reserved memory: initialized node linux,secmon, compatible id aml_secmon_memory
  273. [ 0.000000@0] __reserved_mem_alloc_size: linux,meson-fb
  274. [ 0.000000@0] fb: Reserved memory: created fb at 0x000000003e000000, size 32 MiB
  275. [ 0.000000@0] Reserved memory: initialized node linux,meson-fb, compatible id amlogic, fb-memory
  276. [ 0.000000@0] __reserved_mem_alloc_size: linux,di
  277. [ 0.000000@0] DI reserved memory: created CMA memory pool at 0x000000003c200000, size 30 MiB
  278. [ 0.000000@0] Reserved memory: initialized node linux,di, compatible id amlogic, di-mem
  279. [ 0.000000@0] __reserved_mem_alloc_size: linux,ion-dev
  280. [ 0.000000@0] ppmgr share mem setup
  281. [ 0.000000@0] linux,ion-dev add multi user:ffffffc0019da1d8
  282. [ 0.000000@0] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
  283. [ 0.000000@0] __reserved_mem_alloc_size: linux,codec_mm_cma
  284. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000027800000, size 192 MiB
  285. [ 0.000000@0] Reserved memory: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
  286. [ 0.000000@0] __reserved_mem_alloc_size: linux,picdec
  287. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000037000000, size 48 MiB
  288. [ 0.000000@0] Reserved memory: initialized node linux,picdec, compatible id shared-dma-pool
  289. [ 0.000000@0] __reserved_mem_alloc_size: linux,codec_mm_reserved
  290. [ 0.000000@0] codec_mm:vdec: reserved mem setup
  291. [ 0.000000@0] Reserved memory: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
  292. [ 0.000000@0] cma: Reserved 8 MiB at 36800000
  293. [ 0.000000@0] psci: probing function IDs from device-tree
  294. [ 0.000000@0] PERCPU: Embedded 11 pages/cpu @ffffffc03a1b0000 s13632 r8192 d23232 u45056
  295. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 244696
  296. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.mem_address=0x20000000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3f800000,1080p60hz hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= androidboot.firstboot=1 boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 BOOT_IMAGE=kernel.img mac=D0:76:58:01:AF:75 console=tty0 consoleblank=0 systemd.show_status=auto ssh
  297. [ 0.000000@0] logo: osd1
  298. [ 0.000000@0] logo: loaded
  299. [ 0.000000@0] logo: 0x3f800000
  300. [ 0.000000@0] logo: 1080p60hz
  301. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  302. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  303. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  304. [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
  305. [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
  306. [ 0.000000@0] Memory: 574408K/996352K available (6429K kernel code, 454K rwdata, 2220K rodata, 529K init, 2471K bss, 421944K reserved)
  307. [ 0.000000@0] Virtual kernel memory layout:
  308. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  309. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8041180000 ( 17 MB)
  310. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  311. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc03e000000 ( 992 MB)
  312. [ 0.000000@0] .init : 0xffffffc0018f4000 - 0xffffffc001978540 ( 530 kB)
  313. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc0018f3444 ( 8654 kB)
  314. [ 0.000000@0] .data : 0xffffffc001979000 - 0xffffffc0019eaac0 ( 455 kB)
  315. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
  316. [ 0.000000@0] Hierarchical RCU implementation.
  317. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  318. [ 0.000000@0] CONFIG_RCU_FANOUT set to non-default value of 32
  319. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  320. [ 0.000005@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483648000ns
  321. [ 0.007537@0] mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff8000008994
  322. [ 0.014385@0] local timer MESON TIMER-G mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000a998
  323. [ 0.023463@0] local timer MESON TIMER-H mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000c99c
  324. [ 0.032564@0] local timer MESON TIMER-I mclk->mux_reg =ffffff8000004990,mclk->reg =ffffff800000e9a0
  325. [ 0.041656@0] Switching to timer-based delay loop
  326. [ 0.046578@0] Console: colour dummy device 80x25
  327. [ 0.051016@0] console [tty0] enabled
  328. [ 0.054605@0] bootconsole [earlycon0] disabled
  329. [ 0.059072@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
  330. [ 0.059082@0] pid_max: default: 32768 minimum: 301
  331. [ 0.059169@0] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
  332. [ 0.059176@0] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
  333. [ 0.060463@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
  334. [ 0.060474@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
  335. [ 0.060482@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
  336. [ 0.060490@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
  337. [ 0.062077@0] /cpus/cpu@0: Missing clock-frequency property
  338. [ 0.062086@0] /cpus/cpu@1: Missing clock-frequency property
  339. [ 0.062094@0] /cpus/cpu@2: Missing clock-frequency property
  340. [ 0.062102@0] /cpus/cpu@3: Missing clock-frequency property
  341. [ 0.062434@0] Meson chip version = RevB (1F:B - 0:0)
  342. [ 0.063193@1] CPU1: Booted secondary processor
  343. [ 0.063953@2] CPU2: Booted secondary processor
  344. [ 0.064691@3] CPU3: Booted secondary processor
  345. [ 0.064737@0] Brought up 4 CPUs
  346. [ 0.064752@0] SMP: Total of 4 processors activated.
  347. [ 0.065070@0] devtmpfs: initialized
  348. [ 0.074354@0] pinctrl core: initialized pinctrl subsystem
  349. [ 0.074832@0] regulator-dummy: no parameters
  350. [ 0.075286@0] NET: Registered protocol family 16
  351. [ 0.076470@0] register canvas platform driver
  352. [ 0.076480@0] codec:ignore bus ops for cpu=25
  353. [ 0.076486@0] codec:ignore bus ops for cpu=29
  354. [ 0.076492@0] codec:register amports ops for bus[0]
  355. [ 0.076498@0] codec:register amports ops for bus[4]
  356. [ 0.076503@0] codec:register amports ops for bus[3]
  357. [ 0.076508@0] codec:register amports ops for bus[2]
  358. [ 0.076514@0] codec:register amports ops for bus[1]
  359. [ 0.076519@0] codec:register amports ops for bus[13]
  360. [ 0.076524@0] codec:register amports ops for bus[2]
  361. [ 0.076530@0] codec:register amports ops for bus[14]
  362. [ 0.076577@0] register rdma platform driver
  363. [ 0.077109@0] vdso: 2 pages (1 code, 1 data) at base ffffffc001982000
  364. [ 0.077548@0] DMA: preallocated 256 KiB pool for atomic allocations
  365. [ 0.078742@0] software IO TLB [mem 0x34c00000-0x35000000] (4MB) mapped at [ffffffc034c00000-ffffffc034ffffff]
  366. [ 0.078853@0] hdmitx: system: amhdmitx_init
  367. [ 0.078859@0] hdmitx: system: Ver: 2014May6
  368. [ 0.078908@0] aml_i2c version: 20140813
  369. [ 0.078966@0] tv_vout: tv_init_module
  370. [ 0.078983@0] tv_vout: major number 254 for disp
  371. [ 0.078989@0] vout_notify: vout_register_server
  372. [ 0.078996@0] tv_vout: register tv module server ok
  373. [ 0.079051@0] codec_mm:codec_mm_module_init
  374. [ 0.079204@0] gxbb clk HIU base is 0xffffff8000058000
  375. [ 0.079211@0] gxbb clk ao base is 0xffffff800005a000
  376. [ 0.079245@0] register mpll_clk_out0 success done
  377. [ 0.079254@0] register mpll_clk_out1 success done
  378. [ 0.079263@0] register mpll_clk_out2 success done
  379. [ 0.079415@0] register sys pll success done
  380. [ 0.079449@0] clkrate [ xtal ] : 24000000Hz
  381. [ 0.079456@0] clkrate [ 32Khz ] : 32000Hz
  382. [ 0.079462@0] clkrate [ clk81 ] : 166666666Hz
  383. [ 0.079468@0] clkrate [ fixed_pll ] : 2000000000Hz
  384. [ 0.079474@0] clkrate [ fclk_div2 ] : 1000000000Hz
  385. [ 0.079480@0] clkrate [ fclk_div3 ] : 666666666Hz
  386. [ 0.079486@0] clkrate [ fclk_div4 ] : 500000000Hz
  387. [ 0.079492@0] clkrate [ fclk_div5 ] : 400000000Hz
  388. [ 0.079498@0] clkrate [ fclk_div7 ] : 285714285Hz
  389. [ 0.079522@0] gxbb clock initialization complete
  390. [ 0.079606@0] msr_clk_reg0=ffffff800005c75c,msr_clk_reg2=ffffff800005e764
  391. [ 0.080800@0] amlogic iomap probe done
  392. [ 0.081045@0] Init pinux probe!
  393. [ 0.081573@0] pinmux-gxbb c1109880.pinmux: Probed amlogic pinctrl driver
  394. [ 0.081794@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  395. [ 0.081809@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  396. [ 0.081905@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  397. [ 0.081920@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  398. [ 0.082834@0] codec:codec map io source 0x00000000c1100000,size=1048576 to 0xffffff8000680000
  399. [ 0.082852@0] codec:codec map io source 0x00000000c8820000,size=65536 to 0xffffff80000a0000
  400. [ 0.082868@0] codec:codec map io source 0x00000000c883c000,size=8192 to 0xffffff8000094000
  401. [ 0.082893@0] codec:codec map io source 0x00000000c8100000,size=1048576 to 0xffffff8000800000
  402. [ 0.082907@0] codec:codec map io source 0x00000000d0100000,size=262144 to 0xffffff8000980000
  403. [ 0.082920@0] codec:codec map io source 0x00000000c8838000,size=1024 to 0xffffff800007e000
  404. [ 0.083010@0] codec_mm has 2 memory regions
  405. [ 0.083026@0] codec_mm codec_mm.15: assigned reserved memory node linux,codec_mm_cma ok
  406. [ 0.083038@0] codec_mm:codec_mm_reserved_init 0000000023700000->0000000027800000
  407. [ 0.083047@0] codec_mm codec_mm.15: assigned reserved memory node linux,codec_mm_reserved ok
  408. [ 0.083055@0] codec_mm:codec_mm_probe mem init done
  409. [ 0.083064@0] codec_mm:add reserve memory 0000000023700000(aligned 0000000023700000) size=4100000(aligned 4100000)
  410. [ 0.083116@0] codec_mm has 2 memory regions
  411. [ 0.083127@0] codec_mm codec_mm.15: assigned reserved memory node linux,codec_mm_cma ok
  412. [ 0.083137@0] codec_mm:codec_mm_reserved_init 0000000023700000->0000000027800000
  413. [ 0.083146@0] codec_mm codec_mm.15: assigned reserved memory node linux,codec_mm_reserved ok
  414. [ 0.083154@0] codec_mm:codec_mm reserved memory probed done
  415. [ 0.083159@0] codec_mm:codec_mm_probe ok
  416. [ 0.084127@0] VPU driver version: v01
  417. [ 0.084137@0] vpu driver detect cpu type: gxbaby
  418. [ 0.084150@0] load vpu_clk in dts: 666667000Hz(7)
  419. [ 0.084202@0] vpu_probe OK
  420. [ 0.084816@0] hdmitx: system: amhdmitx_probe
  421. [ 0.084989@0] ------------[ cut here ]------------
  422. [ 0.085005@0] WARNING: CPU: 0 PID: 1 at drivers/base/core.c:552 device_create_file+0xa4/0xb0()
  423. [ 0.085014@0] Attribute phy: read permission without 'show'
  424. [ 0.085020@0] Modules linked in:
  425. [ 0.085029@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.29 #1
  426. [ 0.085037@0] Call trace:
  427. [ 0.085047@0] [<ffffffc0010875b0>] dump_backtrace+0x0/0x120
  428. [ 0.085056@0] [<ffffffc0010876e0>] show_stack+0x10/0x20
  429. [ 0.085066@0] [<ffffffc0016b7a40>] dump_stack+0x78/0x94
  430. [ 0.085075@0] [<ffffffc001092eb8>] warn_slowpath_common+0x88/0xb8
  431. [ 0.085083@0] [<ffffffc001092f24>] warn_slowpath_fmt+0x3c/0x48
  432. [ 0.085090@0] [<ffffffc00138f718>] device_create_file+0xa0/0xb0
  433. [ 0.085102@0] [<ffffffc0014f2154>] amhdmitx_probe+0x1ac/0x978
  434. [ 0.085111@0] [<ffffffc001395a20>] platform_drv_probe+0x20/0x60
  435. [ 0.085120@0] [<ffffffc001393ea4>] driver_probe_device+0x7c/0x248
  436. [ 0.085128@0] [<ffffffc0013940b8>] __device_attach+0x48/0x58
  437. [ 0.085136@0] [<ffffffc001392324>] bus_for_each_drv+0x54/0x98
  438. [ 0.085144@0] [<ffffffc001393dc4>] device_attach+0x9c/0xe0
  439. [ 0.085152@0] [<ffffffc001393310>] bus_probe_device+0x90/0xb8
  440. [ 0.085160@0] [<ffffffc001391300>] device_add+0x370/0x518
  441. [ 0.085170@0] [<ffffffc0014a0e24>] of_device_add+0x4c/0x88
  442. [ 0.085178@0] [<ffffffc0014a161c>] of_platform_device_create_pdata+0x64/0xb0
  443. [ 0.085186@0] [<ffffffc0014a1744>] of_platform_bus_create+0xbc/0x2a0
  444. [ 0.085194@0] [<ffffffc0014a1a50>] of_platform_populate+0x48/0xb8
  445. [ 0.085204@0] [<ffffffc0018f6144>] arm64_device_init+0x24/0x34
  446. [ 0.085212@0] [<ffffffc001081620>] do_one_initcall+0xd0/0x138
  447. [ 0.085220@0] [<ffffffc0018f4928>] kernel_init_freeable+0x138/0x214
  448. [ 0.085228@0] [<ffffffc0016b4b98>] kernel_init+0x10/0xd8
  449. [ 0.085244@0] ---[ end trace c88777cc5c3eebc4 ]---
  450. [ 0.085260@0] ------------[ cut here ]------------
  451. [ 0.085268@0] WARNING: CPU: 0 PID: 1 at drivers/base/core.c:552 device_create_file+0xa4/0xb0()
  452. [ 0.085276@0] Attribute hdcp_ctrl: read permission without 'show'
  453. [ 0.085282@0] Modules linked in:
  454. [ 0.085289@0] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.14.29 #1
  455. [ 0.085295@0] Call trace:
  456. [ 0.085302@0] [<ffffffc0010875b0>] dump_backtrace+0x0/0x120
  457. [ 0.085309@0] [<ffffffc0010876e0>] show_stack+0x10/0x20
  458. [ 0.085317@0] [<ffffffc0016b7a40>] dump_stack+0x78/0x94
  459. [ 0.085326@0] [<ffffffc001092eb8>] warn_slowpath_common+0x88/0xb8
  460. [ 0.085334@0] [<ffffffc001092f24>] warn_slowpath_fmt+0x3c/0x48
  461. [ 0.085341@0] [<ffffffc00138f718>] device_create_file+0xa0/0xb0
  462. [ 0.085349@0] [<ffffffc0014f219c>] amhdmitx_probe+0x1f4/0x978
  463. [ 0.085357@0] [<ffffffc001395a20>] platform_drv_probe+0x20/0x60
  464. [ 0.085365@0] [<ffffffc001393ea4>] driver_probe_device+0x7c/0x248
  465. [ 0.085373@0] [<ffffffc0013940b8>] __device_attach+0x48/0x58
  466. [ 0.085381@0] [<ffffffc001392324>] bus_for_each_drv+0x54/0x98
  467. [ 0.085389@0] [<ffffffc001393dc4>] device_attach+0x9c/0xe0
  468. [ 0.085396@0] [<ffffffc001393310>] bus_probe_device+0x90/0xb8
  469. [ 0.085404@0] [<ffffffc001391300>] device_add+0x370/0x518
  470. [ 0.085412@0] [<ffffffc0014a0e24>] of_device_add+0x4c/0x88
  471. [ 0.085420@0] [<ffffffc0014a161c>] of_platform_device_create_pdata+0x64/0xb0
  472. [ 0.085428@0] [<ffffffc0014a1744>] of_platform_bus_create+0xbc/0x2a0
  473. [ 0.085436@0] [<ffffffc0014a1a50>] of_platform_populate+0x48/0xb8
  474. [ 0.085444@0] [<ffffffc0018f6144>] arm64_device_init+0x24/0x34
  475. [ 0.085452@0] [<ffffffc001081620>] do_one_initcall+0xd0/0x138
  476. [ 0.085459@0] [<ffffffc0018f4928>] kernel_init_freeable+0x138/0x214
  477. [ 0.085467@0] [<ffffffc0016b4b98>] kernel_init+0x10/0xd8
  478. [ 0.085473@0] ---[ end trace c88777cc5c3eebc5 ]---
  479. [ 0.085606@0] hdmitx: system: not find match pwr-ctl
  480. [ 0.085614@0] hdmitx hpd irq = 89
  481. [ 0.085926@0] hdmitx20: Mapped PHY: 0xc0800000
  482. [ 0.085936@0] hdmitx20: Mapped PHY: 0xc1104400
  483. [ 0.085955@0] hdmitx20: Mapped PHY: 0xc8100000
  484. [ 0.085962@0] hdmitx20: Mapped PHY: 0xc8834000
  485. [ 0.085969@0] hdmitx20: Mapped PHY: 0xc883a000
  486. [ 0.085976@0] hdmitx20: Mapped PHY: 0xc883c000
  487. [ 0.085989@0] hdmitx20: Mapped PHY: 0xd0100000
  488. [ 0.085996@0] hdmitx20: Mapped PHY: 0xda83a000
  489. [ 0.086009@0] hdmitx: alread display in uboot 0x1f
  490. [ 0.086030@0] avmute set to 1
  491. [ 0.086489@0] canvas_probe reg=00000000c8838000,size=400
  492. [ 0.086504@0] canvas maped reg_base =ffffff80000b2000
  493. [ 0.089213@0] rdma_probe
  494. [ 0.092957@0] hdmitx: system: irq 80000002
  495. [ 0.126809@0] bio: create slab <bio-0> at 0
  496. [ 0.127352@0] SCSI subsystem initialized
  497. [ 0.127667@0] usbcore: registered new interface driver usbfs
  498. [ 0.127729@0] usbcore: registered new interface driver hub
  499. [ 0.127800@0] usbcore: registered new device driver usb
  500. [ 0.128308@0] i2c-gpio i2c_gpio.29: using pins 153 (SDA) and 154 (SCL)
  501. [ 0.128466@0] pps_core: LinuxPPS API ver. 1 registered
  502. [ 0.128473@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  503. [ 0.128521@0] PTP clock support registered
  504. [ 0.128785@0] logo: logo_init
  505. [ 0.128796@0] tv_vout: tv_set_current_vmode[672]fps_target_mode=12
  506. [ 0.128805@0] tv_vout: mode is 12,sync_duration_den=1,sync_duration_num=60
  507. [ 0.128815@0] switch_vpu_mem_pd: vencp ON
  508. [ 0.128822@0] tv_vout: TV mode 1080p60hz selected.
  509. [ 0.128828@0] tv_vout: already display in uboot
  510. [ 0.128834@0] tv_vout: new mode =1080p60hz set ok
  511. [ 0.128840@0] vout_serve: vinfo mode is: 1080p60hz
  512. [ 0.128846@0] logo: set vmode: 1080p60hz
  513. [ 0.128854@0] switch_vpu_mem_pd: viu_osd1 ON
  514. [ 0.128860@0] switch_vpu_mem_pd: viu_osd2 ON
  515. [ 0.128866@0] switch_vpu_mem_pd: viu_osd_scale ON
  516. [ 0.129017@0] osd_rdma: osd_rdma_init: rmda_table p=0x36841000,op=0x36841000 , v=0xffffff80000d1000
  517. [ 0.129094@0] Advanced Linux Sound Architecture Driver Initialized.
  518. [ 0.130072@0] Switched to clocksource Timer-E
  519. [ 0.137352@0] NET: Registered protocol family 2
  520. [ 0.137720@0] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  521. [ 0.137788@0] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
  522. [ 0.137897@0] TCP: Hash tables configured (established 8192 bind 8192)
  523. [ 0.137964@0] TCP: reno registered
  524. [ 0.137973@0] UDP hash table entries: 512 (order: 2, 16384 bytes)
  525. [ 0.137995@0] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  526. [ 0.138123@0] NET: Registered protocol family 1
  527. [ 0.138268@0] RPC: Registered named UNIX socket transport module.
  528. [ 0.138275@0] RPC: Registered udp transport module.
  529. [ 0.138281@0] RPC: Registered tcp transport module.
  530. [ 0.138287@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
  531. [ 0.138392@0] [wifi_dev_probe] wifi_dev_probe
  532. [ 0.138401@0] [wifi_dev_probe] wifi_dt : interrupt_pin=
  533. [ 0.138429@0] [wifi_dev_probe] wifi_dt : irq_num=null
  534. [ 0.138436@0] [wifi_dev_probe] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
  535. [ 0.138443@0] [wifi_dev_probe] wifi_dt : power_on_pin=
  536. [ 0.138451@0] [wifi_dev_probe] wifi_dt : power_on_pin2=
  537. [ 0.138459@0] [wifi_dev_probe] set pwm as 32k output
  538. [ 0.138500@0] [wifi_dev_probe] interrupt_pin=235
  539. [ 0.138508@0] [wifi_dev_probe] irq_num=100, irq_trigger_type=0
  540. [ 0.138514@0] [wifi_dev_probe] power_on_pin=234
  541. [ 0.138520@0] [wifi_dev_probe] clock_32k_pin=0
  542. [ 0.138679@0] Unpacking initramfs...
  543. [ 0.244070@0] Freeing initrd memory: 3400K (ffffffc033b70000 - ffffffc033ec2000)
  544. [ 0.246251@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
  545. [ 0.256333@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  546. [ 0.257862@0] NFS: Registering the id_resolver key type
  547. [ 0.257894@0] Key type id_resolver registered
  548. [ 0.257901@0] Key type id_legacy registered
  549. [ 0.257912@0] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  550. [ 0.258988@0] msgmni has been set to 1624
  551. [ 0.259892@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
  552. [ 0.259914@0] io scheduler noop registered (default)
  553. [ 0.259921@0] io scheduler deadline registered
  554. [ 0.260125@0] io scheduler cfq registered
  555. [ 0.264303@0] loop: module loaded
  556. [ 0.264844@0] zram: Created 1 device(s) ...
  557. [ 0.264860@0] Loading iSCSI transport class v2.0-870.
  558. [ 0.265730@0] iscsi: registered transport (tcp)
  559. [ 0.267301@0] tun: Universal TUN/TAP device driver, 1.6
  560. [ 0.267318@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  561. [ 0.271564@0] libphy: stmmac: probed
  562. [ 0.271582@0] eth0: PHY ID 02430c54 at 0 IRQ POLL (stmmac-0:00) active
  563. [ 0.271960@0] PPP generic driver version 2.4.2
  564. [ 0.272220@0] NET: Registered protocol family 24
  565. [ 0.272351@0] usbcore: registered new interface driver smsc95xx
  566. [ 0.272567@0] usbcore: registered new interface driver usb-storage
  567. [ 0.272905@0] usbcore: registered new interface driver usbserial
  568. [ 0.273008@0] usbcore: registered new interface driver usbserial_generic
  569. [ 0.273108@0] usbserial: USB Serial support registered for generic
  570. [ 0.273210@0] usbcore: registered new interface driver pl2303
  571. [ 0.273305@0] usbserial: USB Serial support registered for pl2303
  572. [ 0.273534@1] mousedev: PS/2 mouse device common for all mice
  573. [ 0.273689@1] i2c /dev entries driver
  574. [ 0.274490@1] ledtrig-cpu: registered to indicate activity on CPUs
  575. [ 0.274712@1] hidraw: raw HID events driver (C) Jiri Kosina
  576. [ 0.277743@0] usbcore: registered new interface driver usbhid
  577. [ 0.277762@0] usbhid: USB HID core driver
  578. [ 0.278207@1] ashmem: initialized
  579. [ 0.278391@1] logger: created 256K log 'log_main'
  580. [ 0.278562@1] logger: created 256K log 'log_events'
  581. [ 0.278739@1] logger: created 256K log 'log_radio'
  582. [ 0.278904@1] logger: created 256K log 'log_system'
  583. [ 0.279188@1] ==uart0 reg addr = ffffff80000f44c0
  584. [ 0.279214@1] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  585. [ 0.279230@1] ttyS0 use xtal 24000000 change 0 to 115200
  586. [ 0.420180@0] hdmitx: plugin
  587. [ 0.420803@0] hdmitx: system: [edid_tx_segaddr] err = -6
  588. [ 0.420805@0] hdmitx: system: [gpio_read_edid] setptr = 0
  589. [ 0.510648@0] hdmitx: system: [edid_tx_segaddr] err = -6
  590. [ 0.510649@0] hdmitx: system: [gpio_read_edid] setptr = 0
  591. [ 0.551081@0] hdmitx: edid: check sum valid
  592. [ 0.551082@0] hdmitx: edid: check sum valid
  593. [ 0.551085@0] hdmitx: edid: blk0 raw data
  594. [ 0.551117@0] 00ffffffffffff001e6d0100010101010118010380a05a780aee91a3544c9926
  595. [ 0.551117@0] 0f5054a1080031404540614071408180010101010101023a801871382d40582c
  596. [ 0.551117@0] 450040846300001e662150b051001b304070360040846300001e000000fd003a
  597. [ 0.551117@0] 3e1e5310000a202020202020000000fc004c472054560a2020202020202001e7
  598. [ 0.551117@0]
  599. [ 0.551117@0]
  600. [ 0.551119@0] hdmitx: edid: blk1 raw data
  601. [ 0.551148@0] 02033cf154109f0413051403021220212215015d5e5f626364293d06c0150750
  602. [ 0.551148@0] 0957076e030c001000b83c20008001020304e3050301e50e60616566011d8018
  603. [ 0.551148@0] 711c1620582c250040846300009e011d007251d01e206e28550040846300001e
  604. [ 0.551148@0] 000000000000000000000000000000000000000000000000000000000000002d
  605. [ 0.551148@0]
  606. [ 0.551148@0]
  607. [ 0.551152@0] EDID Parser:
  608. [ 0.552216@0] hdmitx: edid: find IEEEOUT
  609. [ 0.552266@0]
  610. [ 0.552280@0] hdmitx: video: get current mode: 1080p60hz
  611. [ 0.552313@0] hdmitx: system: already init VIC = 0 Now VIC = 16
  612. [ 0.552317@0] hdmitx: rx no SCDC present indicator
  613. [ 0.554323@0] hdmitx: ddc rd8b error 0x54 0x01
  614. [ 0.556331@0] hdmitx: ddc rd8b error 0x54 0x01
  615. [ 0.556334@0] hdmirx version is 1.4 or below
  616. [ 0.556337@0] hdmitx: system: set mode VIC 16 (cd0,cs0,pm1,vd0,1)
  617. [ 0.556338@0] hdmitx: system: set pll
  618. [ 0.556339@0] hdmitx: system: param->VIC:16
  619. [ 0.556396@0] hdmitx: set clk of VIC = 16 done
  620. [ 0.556401@0] hdmitx: set enc for VIC: 16
  621. [ 0.556417@0] hdmitx_set_hw[4216] set VIC = 16
  622. [ 0.692073@0] hdmitx: system: phy setting done
  623. [ 0.692083@0] hdmitx: system: irq 80000001
  624. [ 0.695143@0] Start = 0x10000100 End = 0x100001ff
  625. [ 0.695149@0] [0x10000104]: 0x00000001
  626. [ 0.695259@0] [0x10000180]: 0x000000ff
  627. [ 0.695261@0] [0x10000181]: 0x000000ff
  628. [ 0.695263@0] [0x10000182]: 0x00000003
  629. [ 0.695265@0] [0x10000183]: 0x00000007
  630. [ 0.695267@0] [0x10000184]: 0x0000003f
  631. [ 0.695270@0] [0x10000185]: 0x00000002
  632. [ 0.695273@0] [0x10000187]: 0x000000ff
  633. [ 0.695275@0] [0x10000188]: 0x00000003
  634. [ 0.731077@0] Sink is HDMI device
  635. [ 0.731080@0] Source reading EDID
  636. [ 0.760074@0] hdmtix: set audio
  637. [ 0.760081@0] hdmitx tx_aud_src = 0
  638. [ 0.760103@0] hdmitx aud_n_para = 24576
  639. [ 0.760117@0] hdmitx set channel status
  640. [ 0.760166@0] hdmtix: set audio
  641. [ 0.760172@0] hdmitx tx_aud_src = 0
  642. [ 0.760194@0] hdmitx aud_n_para = 24576
  643. [ 0.760208@0] hdmitx set channel status
  644. [ 2.332104@0] console [ttyS0] enabled
  645. [ 2.336087@0] ==uart1 reg addr = ffffff80000f64c0
  646. [ 2.340753@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  647. [ 2.350275@0] dwc_otg: usb1: type: 1 speed: 0, config: 0, dma: 0, id: 1, phy: c0000020, ctrl: 0
  648. [ 2.860981@3] dwc_otg: Core Release: 3.10a
  649. [ 2.861007@3] dwc_otg: Setting default values for core params
  650. [ 2.865144@3] dwc_otg: curmode: 1, host_only: 1
  651. [ 2.881931@0] dwc_otg: Using Buffer DMA mode
  652. [ 2.881954@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
  653. [ 2.885828@0] dwc_otg: Working on port type = HOST
  654. [ 2.890788@0] dwc_otg dwc2_b: DWC OTG Controller
  655. [ 2.895161@0] dwc_otg dwc2_b: new USB bus registered, assigned bus number 1
  656. [ 2.902066@0] dwc_otg dwc2_b: irq 63, io mem 0x00000000
  657. [ 2.907218@0] dwc_otg: -------hcd->flags.d32 = 0
  658. [ 2.911812@0] dwc_otg: Init: Port Power? op_state=1
  659. [ 2.916618@0] dwc_otg: Init1: Power Port (0)
  660. [ 2.920961@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  661. [ 2.927750@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  662. [ 2.935083@0] usb usb1: Product: DWC OTG Controller
  663. [ 2.939907@0] usb usb1: Manufacturer: Linux 3.14.29 dwc_otg_hcd
  664. [ 2.945801@0] usb usb1: SerialNumber: dwc2_b
  665. [ 2.950513@0] hub 1-0:1.0: USB hub found
  666. [ 2.953895@0] hub 1-0:1.0: 1 port detected
  667. [ 2.958138@0] dwc_otg: usb0: type: 1 speed: 0, config: 0, dma: 0, id: 1, phy: c0000000, ctrl: 0
  668. [ 2.979153@0] dwc_otg: Core Release: 3.10a
  669. [ 2.979174@0] dwc_otg: Setting default values for core params
  670. [ 2.983322@0] dwc_otg: curmode: 1, host_only: 1
  671. [ 3.000073@0] dwc_otg: Using Buffer DMA mode
  672. [ 3.000097@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
  673. [ 3.003964@0] dwc_otg: Working on port type = HOST
  674. [ 3.008825@0] dwc_otg dwc2_a: DWC OTG Controller
  675. [ 3.013301@0] dwc_otg dwc2_a: new USB bus registered, assigned bus number 2
  676. [ 3.020202@0] dwc_otg dwc2_a: irq 62, io mem 0x00000000
  677. [ 3.025354@0] dwc_otg: -------hcd->flags.d32 = 0
  678. [ 3.029944@0] dwc_otg: Init: Port Power? op_state=1
  679. [ 3.034759@0] dwc_otg: Init1: Power Port (0)
  680. [ 3.038985@0] DEBUG:set_usb_vbus_power:: set usb port power on (board gpio 1)!
  681. [ 3.038985@0]
  682. [ 3.047904@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  683. [ 3.054690@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  684. [ 3.062020@0] usb usb2: Product: DWC OTG Controller
  685. [ 3.066842@0] usb usb2: Manufacturer: Linux 3.14.29 dwc_otg_hcd
  686. [ 3.072712@0] usb usb2: SerialNumber: dwc2_a
  687. [ 3.077422@0] hub 2-0:1.0: USB hub found
  688. [ 3.080838@0] hub 2-0:1.0: 1 port detected
  689. [ 3.085271@0] ESM HLD: Initializing...
  690. [ 3.088576@0] ESM HLD: Registering device range 'esm'...
  691. [ 3.093863@0] ESM HLD: Device range 'esm' has been registered.
  692. [ 3.099616@0] ESM HLD: Creating class /sys/class/elliptic...
  693. [ 3.105320@0] ESM HLD: The class /sys/class/elliptic has been created.
  694. [ 3.111703@0] ESM HLD: Creating device 'esm'...
  695. [ 3.116339@0] ESM HLD: Device 'esm' has been created.
  696. [ 3.121185@0] ESM HLD: Done initializing the HLD driver.
  697. INFO: HDCP22 key read fail!
  698. INFO: p1d 0
  699. INFO: pd1 0
  700. [ 3.146836@0] aml_vrtc rtc.25: rtc core: registered aml_vrtc as rtc0
  701. [ 3.147742@0] secmon has 1 memory regions
  702. [ 3.151545@0] secmon: share in base: 0xffffff800026a000, share out base: 0xffffff800026c000
  703. [ 3.159803@0] secmon secmon.3: assigned reserved memory node linux,secmon ok
  704. [ 3.166783@0] secmon: probe done
  705. [ 3.170144@0] dwc_otg: Indeed it is in host mode hprt0 = 00021501
  706. [ 3.180231@0] storage: storage in base: 0xffffff8001780000
  707. [ 3.181440@0] storage: storage out base: 0xffffff8001800000
  708. [ 3.186960@0] storage: storage block base: 0xffffff8001880000
  709. [ 3.192658@0] storage: probe done!
  710. [ 3.196639@0] aml_sd_emmc_probe: line 3121
  711. [ 3.200089@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
  712. [ 3.210331@0] aml_sd_emmc_reg_init 796
  713. [ 3.213277@0] pdata->caps 7
  714. [ 3.215942@0] pdata->caps2 0
  715. [ 3.218788@0] get property: port, value:0x00000001
  716. [ 3.225262@0] get property: ocr_avail, value:0x00200080
  717. [ 3.231734@0] get property: f_min, value:0x00061a80
  718. [ 3.238203@0] get property: f_max, value:0x05f5e100
  719. [ 3.244670@0] get property: max_req_size, value:0x00020000
  720. [ 3.251135@0] get property: irq_in, value:0x00000003
  721. [ 3.257600@0] get property: irq_out, value:0x00000005
  722. [ 3.264084@0] get property: gpio_cd, str:
  723. [ 3.269503@0] get property: pinname, str:sd
  724. [ 3.275113@0] get property: jtag_pin, str:
  725. [ 3.280549@0] get property: card_type, value:0x00000005
  726. [ 3.287011@0] get property: gpio_dat3, str
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!