SHOW:
|
|
- or go back to the newest paste.
| 1 | CPU-Z Readme file | |
| 2 | ------------------ | |
| 3 | ||
| 4 | Version 1.81.1 | |
| 5 | October 2017 | |
| 6 | Contact : cpuz@cpuid.com | |
| 7 | Web page: http://www.cpuid.com/softwares/cpu-z.html | |
| 8 | Validation page : http://valid.x86.fr/ | |
| 9 | Hall of Fame : http://valid.x86.fr/records.php | |
| 10 | CPUID SDK : http://www.cpuid-pro.com/products-services.php | |
| 11 | ||
| 12 | ||
| 13 | Configuration file (cpuz.ini) | |
| 14 | ------------------------------ | |
| 15 | ||
| 16 | The configuration file must be named cpuz.ini and be present at the same directory level | |
| 17 | as cpuz.exe. It contains the following : | |
| 18 | ||
| 19 | [CPU-Z] | |
| 20 | VERSION=x.x.x.x | |
| 21 | TextFontName= | |
| 22 | TextFontSize=14 | |
| 23 | TextFontColor=000080 | |
| 24 | LabelFontName= | |
| 25 | LabelFontSize=14 | |
| 26 | ACPI=1 | |
| 27 | PCI=1 | |
| 28 | MaxPCIBus=256 | |
| 29 | DMI=1 | |
| 30 | Sensor=1 | |
| 31 | SMBus=1 | |
| 32 | Display=1 | |
| 33 | UseDisplayAPI=1 | |
| 34 | BusClock=1 | |
| 35 | Chipset=1 | |
| 36 | SPD=1 | |
| 37 | XOC=0 | |
| 38 | CheckUpdates=1 | |
| 39 | ||
| 40 | ||
| 41 | - TextFontName : Font used for the information boxes. | |
| 42 | - TextFontSize : Size of the font used for the information boxes. | |
| 43 | - TextFontColor : Color of the font used for the information boxes. Value is expressed in hexadecimal, and consists in a classic Red/Green/Blue color code : RRGGBB | |
| 44 | - LabelFontName : Font used for the label boxes. | |
| 45 | - LabelFontSize : Size of the font used for the label boxes. | |
| 46 | - Sensor : Set to OFF (or 0) disables sensor chip detection and voltages measurement. 1 to enable. | |
| 47 | - PCI : Set to OFF (or 0) disables the PCI information. This disables chipset, SPD and, depending on the hardware, sensoring information. 1 to enable. | |
| 48 | - MaxPCIBus : Sets the maximum PCI bus to scan. Default value is 256. | |
| 49 | - DMI : Set to OFF (or 0) disables the DMI (Desktop Management Interface) information. This concerns BIOS vendor and version, motherboard vendor and revision. 1 to enable. | |
| 50 | - SMBus : Set to OFF (or 0) disables SMBus information : SPD, and, depending on the hardware, sensoring information. 1 to enable. | |
| 51 | - Display : Set to OFF (or 0) disables the video card information reported in the validator. 1 to enable. | |
| 52 | - UseDisplayAPI : Set to 1, uses the display driver to read the display adapters information. | |
| 53 | - BusClock : Set to 1, uses the bus clock as primary clock source. Set to 0 to use an alternate method. | |
| 54 | - Chipset : set to OFF (or 0) disables the memory controller and southbridge information. 1 to enable. | |
| 55 | - SPD : set to 0 to disable SPD reading. 1 to enable. | |
| 56 | - XOC : eXtreme Overclock Mode : runs CPU-Z with as little system load as possible. Your system won't be fully validated before it is manually checked. Requires to restart CPU-Z. | |
| 57 | - CheckUpdates : set to 0 to disable the new version checker at startup. 1 to enable. | |
| 58 | ||
| 59 | Parameters | |
| 60 | ---------- | |
| 61 | ||
| 62 | -txt=filename : Launch CPU-Z in ghost mode (no interface appears) and generates the register dump file (.txt) | |
| 63 | in the same directory as the exe file. | |
| 64 | ||
| 65 | -html=filename : Same as "-txt" except it generates the html report. | |
| 66 | ||
| 67 | -core=id : Displays clock speed of core #id (id can be set from 0 to Number of cores minus one). | |
| 68 | ||
| 69 | ||
| 70 | Keys | |
| 71 | ---- | |
| 72 | ||
| 73 | F5 : save the current tab in a bmp file | |
| 74 | - | F6 : save the current tab in the clipboard |
| 74 | + | F6 : save the current tab in the clipboard |
| 75 | ||
| 76 | https://pastebin.com/V6A1Eg2J |
