Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb)
- [0000.164] Processing in cold boot mode Bootloader 2
- [0000.169] A02 Bootrom Patch rev = 1023
- [0000.173] Power-up reason: software reset
- [0000.176] No Battery Present
- [0000.179] pmic max77620 reset reason
- [0000.182] pmic max77620 NVERC : 0x0
- [0000.186] RamCode = 0
- [0000.188] Platform has DDR4 type RAM
- [0000.191] max77620 disabling SD1 Remote Sense
- [0000.195] Setting DDR voltage to 1125mv
- [0000.199] Serial Number of Pmic Max77663: 0x1329e1
- [0000.207] Entering ramdump check
- [0000.210] Get RamDumpCarveOut = 0x0
- [0000.213] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
- [0000.219] Last reboot was clean, booting normally!
- [0000.223] Sdram initialization is successful
- [0000.227] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
- [0000.233] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
- [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
- [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
- [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
- [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
- [0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
- [0000.268] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
- [0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
- [0000.291] Platform-DebugCarveout: 0
- [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
- [0000.300] Non secure mode, and RB not enabled.
- [0000.304] BoardID = 3448, SKU = 0x0
- [0000.307] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.311] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.317] Read GPT from (4:0)
- [0000.371] Csd NumOfBlocks=121602048
- [0000.376] Set High speed to 1
- [0000.384] Using GPT Primary to query partitions
- [0000.389] NvTbootFailControlDoFailover: No failover; Continuing ...
- [0000.395] Read PT from (2:0)
- [0000.411] Skip crc32 and magic check
- [0000.414] Using BFS PT to query partitions
- [0000.420] Loading Tboot-CPU binary
- [0000.448] Verifying TBC in OdmNonSecureSBK mode
- [0000.458] Bootloader load address is 0xa0000000, entry address is 0xa0000258
- [0000.465] Bootloader downloaded successfully.
- [0000.469] Downloaded Tboot-CPU binary to 0xa0000258
- [0000.474] MAX77620_GPIO5 configured
- [0000.477] CPU power rail is up
- [0000.480] CPU clock enabled
- [0000.484] Performing RAM repair
- [0000.487] Updating A64 Warmreset Address to 0xa00002e9
- [0000.492] BoardID = 3448, SKU = 0x0
- [0000.495] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.499] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.505] Loading NvTbootBootloaderDTB
- [0000.523] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
- [0000.600] Bootloader DTB Load Address: 0x83000000
- [0000.605] BoardID = 3448, SKU = 0x0
- [0000.608] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.612] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.617] Loading NvTbootKernelDTB
- [0000.636] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
- [0000.712] Kernel DTB Load Address: 0x83100000
- [0000.717] BoardID = 3448, SKU = 0x0
- [0000.720] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.724] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.730] Loading cboot binary
- [0000.759] Verifying EBT in OdmNonSecureSBK mode
- [0000.801] Bootloader load address is 0x92c00000, entry address is 0x92c00258
- [0000.808] Bootloader downloaded successfully.
- [0000.812] BoardID = 3448, SKU = 0x0
- [0000.815] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.819] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.825] NvTbootFailControlDoFailover: No failover; Continuing ...
- [0000.831] PT: Partition NCT NOT found !
- [0000.835] Warning: Find Partition via PT Failed
- [0000.839] Next binary entry address: 0x92c00258
- [0000.844] BoardId: 3448
- [0000.848] Overriding pmu board id with proc board id
- [0000.853] Display board id is not available
- [0000.857] BoardID = 3448, SKU = 0x0
- [0000.861] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0000.865] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0000.870] NvTbootFailControlDoFailover: No failover; Continuing ...
- [0001.680] Bpmp Firmware header magic Id mismatch
- [0001.684] No Bpmp FW loaded
- [0001.687] Not loading WB0 as no bpmp/sc7entry fw
- [0001.691] Set NvDecSticky Bits
- [0001.695] GSC2 address ff53fffc value c0edbbcc
- [0001.701] GSC MC Settings done
- [0001.704] BoardID = 3448, SKU = 0x0
- [0001.707] QSPI-ONLY: SkipQspiOnlyFlag = 1
- [0001.711] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
- [0001.717] TOS Image length 53680
- [0001.720] Monitor size 53680
- [0001.723] OS size 0
- [0001.731] Secure Os AES-CMAC Verification Success!
- [0001.735] TOS image cipher info: plaintext
- [0001.739] Loading and Validation of Secure OS Successful
- [0001.755] NvTbootPackSdramParams: start.
- [0001.760] NvTbootPackSdramParams: done.
- [0001.764] Tegraboot started after 86993 us
- [0001.768] Basic modules init took 811169 us
- [0001.772] Sec Bootdevice Read Time = 822 ms, Read Size = 4194 KB
- [0001.777] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
- [0001.783] Storage Device Read Time = 64 ms, Read Size = 1318 KB
- [0001.789] Storage Device Write Time = 0 ms, Write Size = 0 KB
- [0001.794] Next stage binary read took 822696 us
- [0001.799] Carveout took -853911 us
- [0001.802] CPU initialization took 939542 us
- [0001.806] Total time taken by TegraBoot 1719496 us
- [0001.811] Starting CPU & Halting co-processor
- 64NOTICE: BL31: v1.3(release):b5eeb33
- NOTICE: BL31: Built : 08:56:32, Feb 19 2022
- ERROR: Error initializing runtime service trusty_fast
- [0001.934] RamCode = 0
- [0001.938] LPDDR4 Training: Read DT: Number of tables = 2
- [0001.943] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
- [0001.956] EMC Training Successful
- [0001.959] 408000 not found in DVFS table
- [0001.966] RamCode = 0
- [0001.970] DT Write: emc-table@204000 succeeded
- [0001.975] DT Write: emc-table@1600000 succeeded
- [0001.980] LPDDR4 Training: Write DT: Number of tables = 2
- [0002.036]
- [0002.037] Debug Init done
- [0002.040] Marked DTB cacheable
- [0002.042] Bootloader DTB loaded at 0x83000000
- [0002.047] Marked DTB cacheable
- [0002.050] Kernel DTB loaded at 0x83100000
- [0002.054] DeviceTree Init done
- [0002.067] Pinmux applied successfully
- [0002.072] gicd_base: 0x50041000
- [0002.075] gicc_base: 0x50042000
- [0002.078] Interrupts Init done
- [0002.082] Using base:0x60005090 & irq:208 for tick-timer
- [0002.087] Using base:0x60005098 for delay-timer
- [0002.092] platform_init_timer: DONE
- [0002.095] Timer(tick) Init done
- [0002.099] osc freq = 38400 khz
- [0002.103]
- [0002.104] Welcome to L4T Cboot
- [0002.107]
- [0002.109] Cboot Version: 00.00.2018.01-t210-a2f2e4b8
- [0002.113] calling constructors
- [0002.116] initializing heap
- [0002.119] initializing threads
- [0002.122] initializing timers
- [0002.125] creating bootstrap completion thread
- [0002.129] top of bootstrap2()
- [0002.132] CPU: ARM Cortex A57
- [0002.135] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
- [0002.140] initializing platform
- [0002.149] Manufacturer: MF = 0xc2, ID MSB = 0x25
- [0002.154] ID LSB = 0x36, ID-CFI len = 194 bytes
- [0002.158] Macronix QSPI chip present
- [0002.162] SPI device register
- [0002.165] init boot device
- [0002.167] allocating memory for boot device(SPI)
- [0002.172] registering boot device
- [0002.182] sdmmc node status = okay
- [0002.185] sdcard instance = 0
- [0002.188] sdmmc cd-inverted
- [0002.190] sdcard gpio handle 0x46
- [0002.194] sdcard gpio pin 0xc9
- [0002.197] sdcard gpio flags 0x0
- [0002.200] vmmc-supply 0xaf
- [0002.202] Instance: 0
- [0002.204] Allocating memory for context
- [0002.208] enabling clock
- [0002.211] sd card init
- [0002.213] Check card present and stable
- [0002.217] Send command 0
- [0002.233] Send command 3
- [0002.237] Set RCA for the card
- [0002.240] Query card specific data by command 9
- [0002.247] Parse CSD data
- [0002.249] Send command 7
- [0002.260] Calling sd device register
- [0002.263] Init sdcard
- [0002.265] Allocating memory for boot device
- [0002.269] Registering user device
- [0002.282] Enable APE clock
- [0002.285] Un-powergate APE partition
- [0002.288] of_register: registering tegra_udc to of_hal
- [0002.294] of_register: registering inv20628-driver to of_hal
- [0002.299] of_register: registering ads1015-driver to of_hal
- [0002.305] of_register: registering lp8557-bl-driver to of_hal
- [0002.310] of_register: registering bq2419x_charger to of_hal
- [0002.316] of_register: registering bq27441_fuel_gauge to of_hal
- [0002.330] gpio framework initialized
- [0002.333] of_register: registering tca9539_gpio to of_hal
- [0002.339] of_register: registering tca9539_gpio to of_hal
- [0002.344] of_register: registering i2c_bus_driver to of_hal
- [0002.350] of_register: registering i2c_bus_driver to of_hal
- [0002.355] of_register: registering i2c_bus_driver to of_hal
- [0002.361] pmic framework initialized
- [0002.364] of_register: registering max77620_pmic to of_hal
- [0002.370] regulator framework initialized
- [0002.374] of_register: registering tps65132_bl_driver to of_hal
- [0002.379] initializing target
- [0002.385] gpio_driver_register: register 'tegra_gpio_driver' driver
- [0002.393] board ID = D78, board SKU = 0
- [0002.397] Skipping Z3!
- [0002.403] fixed regulator driver initialized
- [0002.426] initializing OF layer
- [0002.429] NCK carveout not present
- [0002.433] Skipping dts_overrides
- [0002.437] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.456] I2C Bus Init done
- [0002.459] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.471] I2C Bus Init done
- [0002.473] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.485] I2C Bus Init done
- [0002.488] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.499] I2C Bus Init done
- [0002.502] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.514] I2C Bus Init done
- [0002.516] of_children_init: Ops found for compatible string maxim,max77620
- [0002.528] max77620_init using irq 118
- [0002.533] register 'maxim,max77620' pmic
- [0002.537] gpio_driver_register: register 'max77620-gpio' driver
- [0002.543] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
- [0002.555] I2C Bus Init done
- [0002.559] NCK carveout not present
- [0002.571] Find /i2c@7000c000's alias i2c0
- [0002.575] get eeprom at 1-a0, size 256, type 0
- [0002.585] Find /i2c@7000c500's alias i2c2
- [0002.589] get eeprom at 3-a0, size 256, type 0
- [0002.593] get eeprom at 3-ae, size 256, type 0
- [0002.598] pm_ids_update: Updating 1,a0, size 256, type 0
- [0002.603] I2C slave not started
- [0002.606] I2C write failed
- [0002.609] Writing offset failed
- [0002.612] eeprom_init: EEPROM read failed
- [0002.616] pm_ids_update: eeprom init failed
- [0002.620] pm_ids_update: Updating 3,a0, size 256, type 0
- [0002.650] pm_ids_update: The pm board id is 3448-0000-200
- [0002.657] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
- [0002.665] pm_ids_update: pm id update successful
- [0002.670] pm_ids_update: Updating 3,ae, size 256, type 0
- [0002.700] pm_ids_update: The pm board id is 3449-0000-200
- [0002.706] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
- [0002.714] pm_ids_update: pm id update successful
- [0002.745] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
- [0002.751] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
- [0002.759] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
- [0002.765] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
- [0002.774] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:20:d6
- [0002.780] Plugin Manager: Parse ODM data 0x00094800
- [0002.793] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7
- [0002.815] Find /i2c@7000c000's alias i2c0
- [0002.819] get eeprom at 1-a0, size 256, type 0
- [0002.830] Find /i2c@7000c500's alias i2c2
- [0002.833] get eeprom at 3-a0, size 256, type 0
- [0002.838] get eeprom at 3-ae, size 256, type 0
- [0002.842] pm_ids_update: Updating 1,a0, size 256, type 0
- [0002.848] I2C slave not started
- [0002.851] I2C write failed
- [0002.853] Writing offset failed
- [0002.856] eeprom_init: EEPROM read failed
- [0002.860] pm_ids_update: eeprom init failed
- [0002.864] pm_ids_update: Updating 3,a0, size 256, type 0
- [0002.894] pm_ids_update: The pm board id is 3448-0000-200
- [0002.901] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
- [0002.908] pm_ids_update: pm id update successful
- [0002.912] pm_ids_update: Updating 3,ae, size 256, type 0
- [0002.943] pm_ids_update: The pm board id is 3449-0000-200
- [0002.949] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
- [0002.956] pm_ids_update: pm id update successful
- [0002.987] Add serial number:1421919051032 as DT property
- [0002.995] Applying platform configs
- [0003.002] platform-init is not present. Skipping
- [0003.007] calling apps_init()
- [0003.032] Found 16 GPT partitions in "sd0"
- [0003.036] Proceeding to Cold Boot
- [0003.039] starting app android_boot_app
- [0003.043] Device state: unlocked
- [0003.046] display console init
- [0003.057] could not find regulator
- [0003.060] hdmi cable connected
- [0003.076] edid read success
- [0003.089] DT entry for leds-pwm not found
- [0003.095] edid read success
- [0003.098] width = 640, height = 480, frequency = 25174825
- [0003.103] width = 640, height = 480, frequency = 25174825
- [0003.109] width = 2560, height = 1080, frequency = 181250000
- [0003.114] width = 1920, height = 1080, frequency = 148500000
- [0003.120] width = 2560, height = 1080, frequency = 228250000
- [0003.126] width = 1920, height = 1080, frequency = 148351648
- [0003.131] width = 1280, height = 720, frequency = 74175824
- [0003.137] width = 720, height = 480, frequency = 26973026
- [0003.142] width = 640, height = 480, frequency = 25174825
- [0003.148] width = 1920, height = 1080, frequency = 148351648
- [0003.153] width = 1280, height = 720, frequency = 74175824
- [0003.159] width = 720, height = 576, frequency = 26973026
- [0003.164] width = 3840, height = 2160, frequency = 296703296
- [0003.170] width = 3840, height = 2160, frequency = 296703296
- [0003.175] width = 3840, height = 2160, frequency = 296703296
- [0003.181] width = 3840, height = 2160, frequency = 296703296
- [0003.187] Best mode Width = 1920, Height = 1080, freq = 148351648
- [0003.195] tmds-config node not found
- [0003.200] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageps
- [0003.214] setting 'vdd-1v8' regulator to 1800000 micro volts
- [0003.222] could not find regulator
- [0003.225] could not find regulator
- [0003.228] could not find regulator
- [0003.257] using default cmu settings
- [0003.260] dc_hdmi_enable, starting HDMI initialisation
- [0003.267] dc_hdmi_enable, HDMI initialisation complete
- [0003.272] list and configure display window
- [0003.280] display console init completed
- [0003.292] subnode volume_up is not found !
- [0003.296] subnode back is not found !
- [0003.300] subnode volume_down is not found !
- [0003.304] subnode menu is not found !
- [0003.308] Gpio keyboard init success
- [0007.513] decompressor handler not found
- [0007.517] load_bmp_blob: panelresolution=1080 type=3
- [0007.522] -------> se_aes_verify_sbk_clear: 747
- [0007.526] se_aes_verify_sbk_clear: Error
- [0007.530] SE operation failed
- [0007.533] bl_battery_charging: connected to external power supply
- [0007.582] blob_init: USP partition does not have valid Blob
- [0007.588] kfs_getpartname: name = LNX
- [0007.591] Loading kernel from LNX
- [0011.074] load kernel from storage
- [0011.087] found decompressor handler: zlib
- [0012.223] decompressing kernel...
- [0012.227] kernel_source addr:0x95e42000; size:11638261
- [0012.233] kernel_laddr addr:0x80080000; max kernel size:49807360
- [0013.785] Successfully loaded kernel and ramdisk images
- [0013.790] board ID = D78, board SKU = 0
- [0013.795] sdmmc node status = okay
- [0013.798] sdcard instance = 0
- [0013.801] sdmmc cd-inverted
- [0013.804] sdcard gpio handle 0x46
- [0013.807] sdcard gpio pin 0xc9
- [0013.810] sdcard gpio flags 0x0
- [0013.813] vmmc-supply 0xaf
- [0013.816] cd_gpio_pin = 201
- [0013.819] pin_state = 0
- [0013.821] Found sdcard
- [0013.823] SD-card IS present ...
- [0013.826] load_and_boot_kernel: SD card detected OK
- [0013.832] load_bmp_blob: panelresolution=1080 type=3
- [0014.327] display bmp image done
- [0014.330] NCK carveout not present
- [0014.333] Skipping dts_overrides
- [0014.336] NCK carveout not present
- [0014.348] Find /i2c@7000c000's alias i2c0
- [0014.352] get eeprom at 1-a0, size 256, type 0
- [0014.362] Find /i2c@7000c500's alias i2c2
- [0014.366] get eeprom at 3-a0, size 256, type 0
- [0014.371] get eeprom at 3-ae, size 256, type 0
- [0014.375] pm_ids_update: Updating 1,a0, size 256, type 0
- [0014.380] I2C slave not started
- [0014.383] I2C write failed
- [0014.386] Writing offset failed
- [0014.389] eeprom_init: EEPROM read failed
- [0014.393] pm_ids_update: eeprom init failed
- [0014.397] pm_ids_update: Updating 3,a0, size 256, type 0
- [0014.427] pm_ids_update: The pm board id is 3448-0000-200
- [0014.434] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
- [0014.443] pm_ids_update: pm id update successful
- [0014.447] pm_ids_update: Updating 3,ae, size 256, type 0
- [0014.477] pm_ids_update: The pm board id is 3449-0000-200
- [0014.484] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
- [0014.492] pm_ids_update: pm id update successful
- [0014.522] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
- [0014.528] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
- [0014.536] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
- [0014.542] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
- [0014.551] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:20:d6
- [0014.557] Plugin Manager: Parse ODM data 0x00094800
- [0014.570] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7
- [0014.584] Add serial number:1421919051032 as DT property
- [0014.593] Updated bpmp info to DTB
- [0014.598] Updated initrd info to DTB
- [0014.601] "proc-board" doesn't exist, creating
- [0014.608] Updated board info to DTB
- [0014.611] "pmu-board" doesn't exist, creating
- [0014.617] Updated board info to DTB
- [0014.620] "display-board" doesn't exist, creating
- [0014.626] Updated board info to DTB
- [0014.630] "reset" doesn't exist, creating
- [0014.634] Updated reset info to DTB
- [0014.638] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype
- [0014.677] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 root=/dev/sda1 root
- [0014.689] boot image cmdline: sdhci_tegra.en_boot_part_access=1 buildvariant=ug
- [0014.697] Updated bootarg info to DTB
- [0014.701] Adding uuid 000000016441f8081c00000019ff8340 to DT
- [0014.707] Adding eks info 0 to DT
- [0014.713] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
- [0014.719] Updated memory info to DTB
- [0014.727] set vdd_core voltage to 1075 mv
- [0014.731] setting 'vdd-core' regulator to 1075000 micro volts
- [0014.737] Found secure-pmc; disable BPMP
- <6>[ 0.000000] Booting Linux on physical CPU 0x0
- <5>[ 0.000000] Linux version 4.9.141-g4e8759c3f182-dirty (nobody@android-bui2
- <6>[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
- <6>[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,
- <6>[ 0.000000] OF: fdt: - 80000000 , 7ee00000
- <6>[ 0.000000] OF: fdt: - 100000000 , 7f200000
- <6>[ 0.000000] Found tegra_fbmem: 00800000@92cb4000
- <6>[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
- <6>[ 0.000000] bootconsole [uart8250] enabled
- <6>[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fB
- <6>[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fB
- <6>[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fB
- <6>[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fB
- <6>[ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible it
- <6>[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatibs
- <6>[ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
- <6>[ 0.000000] psci: probing for conduit method from DT.
- <6>[ 0.000000] psci: PSCIv1.0 detected in firmware.
- <6>[ 0.000000] psci: Using standard PSCI v0.2 function IDs
- <6>[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- <6>[ 0.000000] psci: SMC Calling Convention v1.1
- <6>[ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc0fef91000 s53592 r8192 8
- <6>[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
- <6>[ 0.000000] Speculative Store Bypass Disable mitigation not required
- <6>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total4
- <5>[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M s
- <6>[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
- <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 b)
- <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 byt)
- <6>[ 0.000000] Memory: 3559808K/4159488K available (15934K kernel code, 2804)
- <5>[ 0.000000] Virtual kernel memory layout:
- <5>[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 1)
- <5>[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 2)
- <5>[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8009010000 ( 159)
- <5>[ 0.000000] .rodata : 0xffffff8009010000 - 0xffffff8009620000 ( 62)
- <5>[ 0.000000] .init : 0xffffff8009620000 - 0xffffff8009de0000 ( 79)
- <5>[ 0.000000] .data : 0xffffff8009de0000 - 0xffffff800a09d008 ( 28)
- <5>[ 0.000000] .bss : 0xffffff800a09d008 - 0xffffff800a140c5c ( 6)
- <5>[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 41)
- <5>[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( )
- <5>[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( )
- <5>[ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( )
- <5>[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 40)
- <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- <6>[ 0.000000] Preemptible hierarchical RCU implementation.
- <6>[ 0.000000] Build-time adjustment of leaf fanout to 64.
- <6>[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
- <6>[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
- <4>[ 0.000000] **********************************************************
- <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
- <4>[ 0.000000] ** **
- <4>[ 0.000000] ** trace_printk() being used. Allocating extra memory. **
- <4>[ 0.000000] ** **
- <4>[ 0.000000] ** This means that this is a DEBUG kernel and it is **
- <4>[ 0.000000] ** unsafe for production use. **
- <4>[ 0.000000] ** **
- <4>[ 0.000000] ** If you see this message and you are not debugging **
- <4>[ 0.000000] ** the kernel, report this immediately to your vendor! **
- <4>[ 0.000000] ** **
- <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
- <4>[ 0.000000] **********************************************************
- <6>[ 0.000000] NR_IRQS:64 nr_irqs:64 0
- <6>[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /r
- <6>[ 0.000000] t210 clock and reset probe
- <6>[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
- <6>[ 0.000000] clk_cbus_recalc_rate: no gbus parent
- <6>[ 0.000000] clk_cbus_recalc_rate: no gbus parent
- <6>[ 0.000000] clk_cbus_recalc_rate: no gbus parent
- <6>[ 0.000000] clk_cbus_recalc_rate: no gbus parent
- <6>[ 0.000000] clk_cbus_recalc_rate: no gbus parent
- <6>[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz.
- <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycs
- <6>[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4s
- <6>[ 0.010449] kmemleak: Kernel memory leak detector disabled
- <6>[ 0.016463] Calibrating delay loop (skipped), value calculated using time)
- <6>[ 0.027310] pid_max: default: 32768 minimum: 301
- <6>[ 0.032809] Security Framework initialized
- <6>[ 0.037315] SELinux: Initializing.
- <6>[ 0.041629] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
- <6>[ 0.048809] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 by)
- <6>[ 0.057670] ftrace: allocating 48498 entries in 190 pages
- <6>[ 0.248058] ASID allocator initialised with 32768 entries
- <6>[ 0.291787] DTS File Name: /media/usb0/home/succhenrica/lineage-porg/lines
- <6>[ 0.314670] DTB Build time: Apr 19 2022 19:17:33
- <6>[ 0.321847] tegra-id: chipid=22117.
- <6>[ 0.325722] tegra-id: opt_subrevision=0.
- <6>[ 0.330046] Tegra Speedo/IDDQ fuse revision 4
- <6>[ 0.334804] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
- <6>[ 0.341617] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
- <6>[ 0.348698] Tegra: CPU Speedo Value 2101, SoC Speedo Value 2009, GPU Spee2
- <6>[ 0.357126] Tegra: CPU IDDQ Value 2656, SoC IDDQ Value 2932, GPU IDDQ Val0
- <6>[ 0.365030] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
- <6>[ 0.372122] DTS File Name: /media/usb0/home/succhenrica/lineage-porg/lines
- <6>[ 0.394951] DTB Build time: Apr 19 2022 19:17:33
- <6>[ 0.449607] CPU1: Booted secondary processor [411fd071]
- <6>[ 0.481505] CPU2: Booted secondary processor [411fd071]
- <6>[ 0.513519] CPU3: Booted secondary processor [411fd071]
- <6>[ 0.513614] Brought up 4 CPUs
- <6>[ 0.533918] SMP: Total of 4 processors activated.
- <6>[ 0.539036] CPU features: detected feature: 32-bit EL0 Support
- <6>[ 0.545313] CPU features: detected feature: Kernel page table isolation ()
- <6>[ 0.676025] CPU: All CPU(s) started at EL2
- <6>[ 0.680538] alternatives: patching kernel code
- <6>[ 0.694415] devtmpfs: initialized
- <6>[ 0.743835] Initilizing CustomIPI irq domain
- <6>[ 0.749012] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffffs
- <6>[ 0.759354] futex hash table entries: 1024 (order: 4, 65536 bytes)
- <6>[ 0.766175] cma: strict cma policy: off
- <6>[ 0.781832] pinctrl core: initialized pinctrl subsystem
- <6>[ 0.788069] OS set in device tree is not L4T.
- <6>[ 0.793315] regulator-dummy: no parameters
- <6>[ 0.798116] Initializing plugin-manager
- <6>[ 0.802495] Plugin module not found
- <6>[ 0.806479] node /plugin-manager/fragement@0 match with board >=3448-00000
- <6>[ 0.814788] node /plugin-manager/fragment@1 match with board >=3448-0000-1
- <6>[ 0.822821] node /plugin-manager/fragment@5 match with board 3449-0000-200
- <6>[ 0.830536] node /plugin-manager/fragement@6 match with odm-data enable-tt
- <6>[ 0.838766] node /plugin-manager/fragement@8 match with odm-data enable-tt
- <6>[ 0.846964] node /plugin-manager/fragement@9 match with board <3448-0000-0
- <6>[ 0.858260] NET: Registered protocol family 16
- <6>[ 0.863912] schedtune: init normalization constants...
- <6>[ 0.869499] schedtune: no energy model data
- <4>[ 0.874084] schedtune: disabled!
- <5>[ 0.893521] random: fast init done
- <6>[ 0.894358] pstore: using zlib compression
- <6>[ 0.902562] console [pstore-1] enabled
- <6>[ 0.906986] pstore: Registered ramoops as persistent store backend
- <6>[ 0.913648] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
- <6>[ 0.932746] cpuidle: using governor menu
- <6>[ 0.941094] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
- <6>[ 0.949974] vdso: 2 pages (1 code @ ffffff8009017000, 1 data @ ffffff8009)
- <6>[ 0.957916] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- <6>[ 0.969262] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for as
- <6>[ 0.980618] tegra_bpmp_of_clk_init: EMC proxy not found.
- <6>[ 0.987370] tegra_powergate_init: DONE
- <6>[ 0.991545] DTS File Name: /media/usb0/home/succhenrica/lineage-porg/lines
- <6>[ 1.014405] DTB Build time: Apr 19 2022 19:17:33
- <6>[ 1.021759] Tegra reboot handler registered.
- <6>[ 1.031239] iommu: Adding device tegra-carveouts to group 0
- <6>[ 1.037432] platform tegra-carveouts: domain=ffffffc0f90e13d8 allocates a8
- <6>[ 1.046674] platform tegra-carveouts: domain=ffffffc0f90e13d8 allocates a0
- <6>[ 1.055898] platform tegra-carveouts: domain=ffffffc0f90e13d8 allocates a8
- <6>[ 1.065485] iommu: Adding device smmu_test to group 1
- <6>[ 1.071048] platform smmu_test: domain=ffffffc0f90e1618 allocates as[0]=f0
- <6>[ 1.079761] platform smmu_test: domain=ffffffc0f90e1618 allocates as[1]=f8
- <6>[ 1.088446] platform smmu_test: domain=ffffffc0f90e1618 allocates as[2]=f0
- <6>[ 1.098150] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
- <6>[ 1.105161] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
- <6>[ 1.112173] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
- <6>[ 1.119115] nv-tegra-mc 70019000.mc: No mssnvlink node
- <6>[ 1.124731] mc-err: mcerr ops are set to t21x
- <6>[ 1.140104] iommu: Adding device 70090000.xusb to group 2
- <6>[ 1.146308] iommu: Adding device 70006000.serial to group 3
- <6>[ 1.152414] platform 70006000.serial: domain=ffffffc0f910ad98 allocates a8
- <6>[ 1.162063] iommu: Adding device 70006040.serial to group 4
- <6>[ 1.168388] iommu: Adding device 70006200.serial to group 5
- <6>[ 1.174622] iommu: Adding device sound to group 6
- <6>[ 1.179820] platform sound: domain=ffffffc0f916a318 allocates as[0]=fffff0
- <6>[ 1.188683] iommu: Adding device 7000d400.spi to group 7
- <6>[ 1.194736] iommu: Adding device 7000d600.spi to group 8
- <6>[ 1.200797] iommu: Adding device 70410000.spi to group 9
- <6>[ 1.206889] iommu: Adding device 50000000.host1x to group 10
- <6>[ 1.213319] iommu: Adding device 54080000.vi to group 11
- <6>[ 1.219517] iommu: Adding device 54600000.isp to group 12
- <6>[ 1.225731] iommu: Adding device 54680000.isp to group 13
- <6>[ 1.231911] iommu: Adding device tegradc.0 to group 14
- <6>[ 1.237573] platform tegradc.0: domain=ffffffc0f91b8258 allocates as[0]=f8
- <6>[ 1.250573] platform tegradc.0: IOVA linear map 0x0000000092cb4000(800000)
- <6>[ 1.258308] iommu: Adding device tegradc.1 to group 15
- <6>[ 1.263962] platform tegradc.1: domain=ffffffc0f91b8498 allocates as[0]=f0
- <6>[ 1.276963] platform tegradc.1: IOVA linear map 0x0000000092cb4000(800000)
- <6>[ 1.284671] iommu: Adding device 54340000.vic to group 16
- <6>[ 1.290795] iommu: Adding device 544c0000.nvenc to group 17
- <6>[ 1.297061] iommu: Adding device 54500000.tsec to group 18
- <6>[ 1.303240] iommu: Adding device 54100000.tsecb to group 19
- <6>[ 1.309501] iommu: Adding device 54480000.nvdec to group 20
- <6>[ 1.315788] iommu: Adding device 54380000.nvjpg to group 21
- <6>[ 1.322927] iommu: Adding device 546c0000.i2c to group 22
- <6>[ 1.329154] iommu: Adding device 57000000.gpu to group 23
- <6>[ 1.335080] platform 57000000.gpu: domain=ffffffc0f91cb498 allocates as[08
- <6>[ 1.344056] platform 57000000.gpu: domain=ffffffc0f91cb498 allocates as[10
- <6>[ 1.353020] platform 57000000.gpu: domain=ffffffc0f91cb498 allocates as[28
- <6>[ 1.361967] platform 57000000.gpu: domain=ffffffc0f91cb498 allocates as[30
- <4>[ 1.371935] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergen.
- <6>[ 1.381589] tegra-pmc 7000e400.pmc: scratch reg offset dts data not preset
- <6>[ 1.389078] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET
- <6>[ 1.395658] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
- <6>[ 1.402326] tegra-pmc: ### PMC reset status reg: 0x3
- <6>[ 1.456892] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl regisd
- <6>[ 1.464648] tegra-pmc: Clear bootloader IO dpd settings
- <6>[ 1.470348] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
- <6>[ 1.476987] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom rs
- <6>[ 1.485752] iommu: Adding device 70012000.se to group 24
- <6>[ 1.492133] iommu: Adding device 1003000.pcie to group 25
- <6>[ 1.498068] platform 1003000.pcie: domain=ffffffc0f91cbc18 allocates as[08
- <6>[ 1.507017] platform 1003000.pcie: domain=ffffffc0f91cbc18 allocates as[10
- <6>[ 1.515978] platform 1003000.pcie: domain=ffffffc0f91cbc18 allocates as[28
- <6>[ 1.525369] iommu: Adding device 7000c000.i2c to group 26
- <6>[ 1.531530] iommu: Adding device 7000c400.i2c to group 27
- <6>[ 1.537704] iommu: Adding device 7000c500.i2c to group 28
- <6>[ 1.543827] iommu: Adding device 7000c700.i2c to group 29
- <6>[ 1.549945] iommu: Adding device 7000d000.i2c to group 30
- <6>[ 1.556073] iommu: Adding device 7000d100.i2c to group 31
- <6>[ 1.562239] iommu: Adding device sdhci-tegra.0 to group 32
- <6>[ 1.568254] platform sdhci-tegra.0: domain=ffffffc0f91de798 allocates as[0
- <6>[ 1.577294] platform sdhci-tegra.0: domain=ffffffc0f91de798 allocates as[8
- <6>[ 1.586333] platform sdhci-tegra.0: domain=ffffffc0f91de798 allocates as[0
- <6>[ 1.596234] iommu: Adding device 700d0000.xudc to group 33
- <6>[ 1.605685] vdd-ac-bat: 5000 mV
- <6>[ 1.609679] vdd-5v0-sys: 5000 mV
- <6>[ 1.614795] vdd-5v0-hdmi: supplied by vdd-5v0-sys
- <6>[ 1.620029] vdd-5v0-hdmi: 5000 mV
- <6>[ 1.624275] vdd-1v8-sys: 1800 mV
- <6>[ 1.628424] vdd-fan: supplied by vdd-5v0-sys
- <6>[ 1.633156] vdd-fan: 5000 mV
- <6>[ 1.636929] vdd-usb-vbus: supplied by vdd-5v0-sys
- <6>[ 1.642158] vdd-usb-vbus: 5000 mV
- <6>[ 1.646638] vdd-usb-vbus2: 5000 mV
- <6>[ 1.685665] HugeTLB registered 2 MB page size, pre-allocated 0 pages
- <6>[ 1.698350] gpio gpiochip0: gpio-line-names specifies 240 line names but p
- <6>[ 1.709632] GPIO line 151 (camera-control-output-low) hogged as output/low
- <6>[ 1.717411] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpio)
- <6>[ 1.735003] eventlib_kernel: keventlib is initialized, test id: 0
- <5>[ 1.741994] SCSI subsystem initialized
- <6>[ 1.746777] usbcore: registered new interface driver usbfs
- <6>[ 1.752800] usbcore: registered new interface driver hub
- <6>[ 1.758662] usbcore: registered new device driver usb
- <6>[ 1.768476] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
- <6>[ 1.781641] vdd-core: 600 <--> 1162 mV at 1075 mV
- <6>[ 1.787929] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
- <6>[ 1.797634] vdd-ddr-1v1: 1150 mV
- <6>[ 1.805625] vdd-pre-reg-1v35: 1350 mV
- <6>[ 1.813629] vdd-1v8: 1800 mV
- <6>[ 1.820737] avdd-sys-1v2: 1200 mV
- <6>[ 1.828734] vdd-pex-1v0: 1050 mV
- <6>[ 1.833182] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV
- <6>[ 1.839657] max77620-ldo3: at 3100 mV
- <6>[ 1.844738] vdd-rtc: 850 <--> 1100 mV at 1000 mV
- <6>[ 1.850482] max77620-ldo5: at 3100 mV
- <6>[ 1.855259] max77620-ldo6: at 2800 mV
- <6>[ 1.860736] avdd-1v05-pll: 1050 mV
- <6>[ 1.868737] avdd-io-hdmi-dp: 1050 mV
- <6>[ 1.874064] GPIO line 505 (spmic-default-output-high) hogged as output/hih
- <6>[ 1.881838] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gp)
- <6>[ 1.892888] max77620 4-003c: max77620 probe successful
- <6>[ 1.901899] media: Linux media interface: v0.10
- <6>[ 1.906923] Linux video capture interface: v2.00
- <6>[ 1.913120] pps_core: LinuxPPS API ver. 1 registered
- <6>[ 1.918553] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo G>
- <6>[ 1.928290] PTP clock support registered
- <6>[ 1.937389] tegra_fiq_debugger_init: found FIQ source (IRQ 99)
- <6>[ 1.947149] tegra210-emc 7001b000.external-memory-controller: validated Ee
- <6>[ 1.956475] Advanced Linux Sound Architecture Driver Initialized.
- <6>[ 1.963751] Bluetooth: Core ver 2.22
- <6>[ 1.967798] NET: Registered protocol family 31
- <6>[ 1.972677] Bluetooth: HCI device and connection manager initialized
- <6>[ 1.979530] Bluetooth: HCI socket layer initialized
- <6>[ 1.984860] Bluetooth: L2CAP socket layer initialized
- <6>[ 1.990383] Bluetooth: SCO socket layer initialized
- <6>[ 1.997603] tegra210_dvfs: no clock found for sdmmc2_ddr
- <6>[ 2.003411] tegra210_dvfs: no clock found for sdmmc4_ddr
- <6>[ 2.009224] tegra210_dvfs: no clock found for sdmmc1_ddr
- <6>[ 2.015001] tegra210_dvfs: no clock found for sdmmc3_ddr
- <6>[ 2.024420] tegra_dvfs: Unable to get vdd-cpu rail for step info, deferine
- <6>[ 2.033804] vdd-3v3-sys: supplied by vdd-5v0-sys
- <6>[ 2.038975] vdd-3v3-sys: 3300 mV
- <6>[ 2.042989] vdd-1v8-sys: supplied by vdd-3v3-sys
- <6>[ 2.048820] vdd-usb-vbus2: supplied by vdd-3v3-sys
- <6>[ 2.054577] vdd-3v3-sd: supplied by vdd-3v3-sys
- <6>[ 2.059583] vdd-3v3-sd: 3300 mV
- <6>[ 2.064153] avdd-io-edp-1v05: supplied by avdd-1v05-pll
- <6>[ 2.069885] avdd-io-edp-1v05: 1050 mV
- <6>[ 2.074575] vdd-usb-hub-en: supplied by vdd-1v8-sys
- <6>[ 2.079937] vdd-usb-hub-en: 5000 mV
- <6>[ 2.085361] camchar: rtcpu character device driver loaded
- <6>[ 2.091966] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
- <6>[ 2.100994] clocksource: Switched to clocksource arch_sys_counter
- <5>[ 2.156623] VFS: Disk quotas dquot_6.6.0
- <6>[ 2.161168] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- <5>[ 2.168815] FS-Cache: Loaded
- <6>[ 2.172360] nvmap_heap_init: nvmap_heap_init: created heap block cache
- <6>[ 2.179844] dma_declare_coherent_resizable_cma_memory:331: resizable heap0
- <6>[ 2.183316] thermal thermal_zone0: Registering thermal zone thermal_zone0m
- <6>[ 2.183866] thermal thermal_zone1: Registering thermal zone thermal_zone1m
- <6>[ 2.184287] thermal thermal_zone2: Registering thermal zone thermal_zone2m
- <6>[ 2.184610] thermal thermal_zone3: Registering thermal zone thermal_zone3m
- <6>[ 2.184812] thermal thermal_zone4: Registering thermal zone thermal_zone4e
- <6>[ 2.185185] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
- <6>[ 2.185187] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
- <6>[ 2.185659] NET: Registered protocol family 2
- <6>[ 2.186706] TCP established hash table entries: 32768 (order: 6, 262144 b)
- <6>[ 2.186920] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
- <6>[ 2.187477] TCP: Hash tables configured (established 32768 bind 32768)
- <6>[ 2.187635] UDP hash table entries: 2048 (order: 4, 65536 bytes)
- <6>[ 2.187719] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
- <6>[ 2.188184] NET: Registered protocol family 1
- <6>[ 2.188711] Trying to unpack rootfs image as initramfs...
- <6>[ 2.299644] dma-vpr: heap size is not multiple of cma_chunk_size heap_in)
- <6>[ 2.311350] cma: enabled page replacement for spfn=d7000, epfn=f0000
- <6>[ 2.318234] dma_declare_coherent_resizable_cma_memory:380: resizable cma t
- <6>[ 2.336379] nvmap_page_pool_init: Total RAM pages: 1008736
- <6>[ 2.342359] nvmap_page_pool_init: nvmap page pool size: 126092 pages (492)
- <6>[ 2.350195] nvmap_background_zero_thread: PP zeroing thread starting.
- <6>[ 2.350579] misc nvmap: created heap vpr base 0x00000000d7000000 size (40)
- <6>[ 2.527936] Freeing initrd memory: 7936K
- <6>[ 2.545305] host1x 50000000.host1x: initialized
- <6>[ 2.553403] falcon 54340000.vic: initialized
- <6>[ 2.559668] falcon 544c0000.nvenc: initialized
- <6>[ 2.565899] falcon 54380000.nvjpg: initialized
- <6>[ 2.572810] nvdec 54480000.nvdec: initialized
- <6>[ 2.578716] tsec 54500000.tsec: initialized
- <6>[ 2.584229] tsec 54100000.tsecb: initialized
- <6>[ 2.590181] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 countere
- <6>[ 2.601354] audit: initializing netlink subsys (disabled)
- <5>[ 2.607322] audit: type=2000 audit(1.883:1): initialized
- <6>[ 2.613912] workingset: timestamp_bits=46 max_order=20 bucket_order=0
- <6>[ 2.632372] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- <6>[ 2.639115] Registering sdcardfs 0.1
- <6>[ 2.644567] ntfs: driver 2.1.32 [Flags: R/W].
- <6>[ 2.650566] fuse init (API version 7.26)
- <6>[ 2.658013] tlk_driver_misc_init: tlk not enabled on this device
- <6>[ 2.667656] NET: Registered protocol family 38
- <5>[ 2.672556] Key type asymmetric registered
- <5>[ 2.677141] Asymmetric key parser 'x509' registered
- <6>[ 2.682810] Block layer SCSI generic (bsg) driver version 0.4 loaded (maj)
- <6>[ 2.690758] io scheduler noop registered
- <6>[ 2.695097] io scheduler deadline registered
- <6>[ 2.700096] io scheduler cfq registered (default)
- <6>[ 2.708092] gic 702f9000.agic: GIC IRQ controller registered
- <6>[ 2.717345] iommu: Adding device 702ef000.adsp to group 34
- <6>[ 2.730557] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registerd
- <6>[ 2.738631] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0
- <6>[ 2.747106] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_4
- <6>[ 2.757514] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lanb
- <6>[ 2.767355] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lanb
- <6>[ 2.777169] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lanb
- <6>[ 2.787071] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lan1
- <6>[ 2.797154] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lan4
- <6>[ 2.807224] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lan4
- <6>[ 2.817289] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lan4
- <6>[ 2.827365] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lan4
- <6>[ 2.837433] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lanb
- <6>[ 2.847242] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lanb
- <6>[ 2.863386] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
- <6>[ 2.871579] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
- <6>[ 2.880263] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
- <6>[ 2.887606] tegra-pcie 1003000.pcie: PCIE: Enable power rails
- <6>[ 2.890138] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_0
- <6>[ 2.895144] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x7008
- <6>[ 2.895151] tegra_cec 70015000.tegra_cec: Unpowergated DISP
- <6>[ 2.895199] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
- <5>[ 2.895385] tegra_cec 70015000.tegra_cec: tegra_cec_init started
- <6>[ 2.895437] tegradc tegradc.0: disp0 connected to head0->/host1x@500000001
- <6>[ 2.895518] display board info: id 0x0, fab 0x0
- <6>[ 2.895602] generic_infoframe_type: 0x87
- <6>[ 2.895641] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
- <5>[ 2.895645] tegra_cec 70015000.tegra_cec: probed
- <6>[ 2.895761] tegradc tegradc.0: DT parsed successfully
- <6>[ 2.895811] tegradc tegradc.0: Display dc.ffffff800ab00000 registered wit0
- <6>[ 2.896418] tegradc tegradc.0: Bootloader disp_param detected. Detected m1
- <6>[ 2.900619] tegradc tegradc.0: probed
- <6>[ 2.906374] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32s
- <6>[ 2.908387] kfuse 7000fc00.kfuse: initialized
- <6>[ 2.910052] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit ched
- <6>[ 2.910057] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver id
- <6>[ 2.912310] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-se
- <6>[ 2.913722] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
- <6>[ 2.915194] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available w
- <6>[ 2.915210] vdd-cpu: 708 <--> 1322 mV at 708 mV
- <6>[ 2.915770] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator rd
- <6>[ 2.917719] vdd-gpu: applied init 1000000uV constraint
- <6>[ 2.917727] vdd-gpu: 708 <--> 1323 mV at 997 mV
- <6>[ 2.918225] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator rd
- <6>[ 2.918933] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
- <6>[ 2.919071] No Device Node present for smmu client: serial8250 !!
- <5>[ 2.919082] platform serial8250: No iommus property found in DT node, got)
- <6>[ 2.919147] iommu: Adding device serial8250 to group 35
- <6>[ 2.943755] console [ttyS0] disabled
- <6>[ 3.109479] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baua
- <6>[ 3.109890] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
- <6>[ 3.112023] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
- <6>[ 3.132342] tegradc tegradc.0: fb registered
- <6>[ 3.132342] tegradc tegradc.0: fb registered
- <6>[ 3.132357] console [ttyS0] enabled
- <6>[ 3.132357] console [ttyS0] enabled
- <6>[ 3.132361] bootconsole [uart8250] disabled
- <6>[ 3.132361] bootconsole [uart8250] disabled
- <6>[ 3.159990] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_bT
- <6>[ 3.161920] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_.
- <6>[ 3.161952] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_m
- <6>[ 3.162406] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by.
- <6>[ 3.162415] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by.
- <6>[ 3.194426] extcon-disp-state extcon:disp-state: cable 47 state 1
- <6>[ 3.194430] Extcon AUX1(HDMI) enable
- <6>[ 3.195423] tegradc tegradc.1: disp1 connected to head1->/host1x@50000000r
- <6>[ 3.195509] tegradc tegradc.1: No lt-data, using default setting
- <6>[ 3.195534] tegradc tegradc.1: No hpd-gpio in DT
- <6>[ 3.195562] tegradc tegradc.1: DT parsed successfully
- <6>[ 3.195610] tegradc tegradc.1: Display dc.ffffff800f480000 registered wit1
- <3>[ 3.197090] tegradc tegradc.1: dpd enable lookup fail:-19
- <6>[ 3.201604] tegradc tegradc.1: probed
- <6>[ 3.234167] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 di4
- <6>[ 3.285836] tegradc tegradc.1: fb registered
- <6>[ 3.286094] serial-tegra 70006200.serial: RX in PIO mode
- <6>[ 3.286196] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_bT
- <6>[ 3.311574] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_e1
- <6>[ 3.319014] hpd: switching from state 7 (Takeover from bootloader) to sta)
- <6>[ 3.330355] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
- <6>[ 3.336136] extcon-disp-state extcon:disp-state: cable 44 state 0 already.
- <6>[ 3.337259] brd: module loaded
- <6>[ 3.347177] Extcon DP: HPD disabled
- <6>[ 3.351009] extcon-disp-state extcon:disp-state: cable 53 state 1
- <6>[ 3.353240] loop: module loaded
- <6>[ 3.355519] nbd: registered device at major 43
- <6>[ 3.365573] hpd: hpd_switch 0
- <6>[ 3.365578] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
- <6>[ 3.370705] zram: Added device: zram0
- <6>[ 3.371355] tegra_profiler: version: 1.146, samples/io: 49/28
- <6>[ 3.371458] tegra_profiler: auth: init
- <6>[ 3.372276] hisi_sas: driver version v1.6
- <6>[ 3.383088] tegra-qspi 70410000.spi: Prod settings list not found
- <6>[ 3.385803] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
- <6>[ 3.385810] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x4000000
- <6>[ 3.387831] libphy: Fixed MDIO Bus: probed
- <6>[ 3.388442] tun: Universal TUN/TAP device driver, 1.6
- <6>[ 3.388444] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- <6>[ 3.389149] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
- <6>[ 3.389150] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
- <6>[ 3.389194] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0k
- <6>[ 3.389195] igb: Copyright (c) 2007-2014 Intel Corporation.
- <6>[ 3.389242] igbvf: Intel(R) Gigabit Virtual Function Network Driver - verk
- <6>[ 3.389243] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
- <6>[ 3.389285] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.64
- <6>[ 3.389287] Copyright(c) 1999 - 2017 Intel Corporation.
- <6>[ 3.389403] sky2: driver version 1.30
- <6>[ 3.390016] PPP generic driver version 2.4.2
- <6>[ 3.390141] PPP BSD Compression module registered
- <6>[ 3.390143] PPP Deflate Compression module registered
- <6>[ 3.390160] PPP MPPE Compression module registered
- <6>[ 3.390164] NET: Registered protocol family 24
- <6>[ 3.390169] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernetr
- <6>[ 3.390223] usbcore: registered new interface driver pegasus
- <6>[ 3.390258] usbcore: registered new interface driver rtl8150
- <6>[ 3.390304] usbcore: registered new interface driver asix
- <6>[ 3.390338] usbcore: registered new interface driver ax88179_178a
- <6>[ 3.390375] usbcore: registered new interface driver cdc_ether
- <6>[ 3.390409] usbcore: registered new interface driver dm9601
- <6>[ 3.390453] usbcore: registered new interface driver CoreChips
- <6>[ 3.390497] usbcore: registered new interface driver smsc75xx
- <6>[ 3.390539] usbcore: registered new interface driver smsc95xx
- <6>[ 3.390573] usbcore: registered new interface driver net1080
- <6>[ 3.390608] usbcore: registered new interface driver plusb
- <6>[ 3.390645] usbcore: registered new interface driver cdc_subset
- <6>[ 3.390679] usbcore: registered new interface driver zaurus
- <6>[ 3.390714] usbcore: registered new interface driver MOSCHIP usb-ethernetr
- <6>[ 3.390758] usbcore: registered new interface driver cdc_ncm
- <6>[ 3.390792] usbcore: registered new interface driver r8152
- <6>[ 3.390926] VFIO - User Level meta-driver version: 0.3
- <6>[ 3.391905] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- <6>[ 3.391916] ehci-pci: EHCI PCI platform driver
- <6>[ 3.391961] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- <6>[ 3.391968] ohci-pci: OHCI PCI platform driver
- <6>[ 3.392008] ohci-platform: OHCI generic platform driver
- <6>[ 3.393685] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
- <6>[ 3.393769] tegra-xusb 70090000.xusb: enable external cdp 1
- <6>[ 3.393775] tegra-xusb 70090000.xusb: enable external cdp 2
- <6>[ 3.393780] tegra-xusb 70090000.xusb: enable external cdp 3
- <6>[ 3.394258] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI p0
- <6>[ 3.395347] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f8962000 id
- <6>[ 3.397041] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 16:0e
- <6>[ 3.397076] tegra-xusb 70090000.xusb: xHCI Host Controller
- <6>[ 3.397094] tegra-xusb 70090000.xusb: new USB bus registered, assigned bu1
- <6>[ 3.397830] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 00
- <6>[ 3.397868] tegra-xusb 70090000.xusb: irq 62, io mem 0x70090000
- <6>[ 3.398202] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- <6>[ 3.398208] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNum1
- <6>[ 3.398211] usb usb1: Product: xHCI Host Controller
- <6>[ 3.398214] usb usb1: Manufacturer: Linux 4.9.141-g4e8759c3f182-dirty xhcd
- <6>[ 3.398218] usb usb1: SerialNumber: 70090000.xusb
- <6>[ 3.398538] usbcore: registered new interface driver usb-storage
- <6>[ 3.398584] usbcore: registered new interface driver usb_ehset_test
- <6>[ 3.398893] hub 1-0:1.0: USB hub found
- <6>[ 3.398930] hub 1-0:1.0: 5 ports detected
- <6>[ 3.399433] tegra-xusb 70090000.xusb: xHCI Host Controller
- <6>[ 3.399444] tegra-xusb 70090000.xusb: new USB bus registered, assigned bu2
- <6>[ 3.399531] usb usb2: We don't know the algorithms for LPM for this host,.
- <6>[ 3.399666] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
- <6>[ 3.399670] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNum1
- <6>[ 3.399674] usb usb2: Product: xHCI Host Controller
- <6>[ 3.399677] usb usb2: Manufacturer: Linux 4.9.141-g4e8759c3f182-dirty xhcd
- <6>[ 3.399680] usb usb2: SerialNumber: 70090000.xusb
- <6>[ 3.400127] hub 2-0:1.0: USB hub found
- <6>[ 3.400159] hub 2-0:1.0: 4 ports detected
- <6>[ 3.400848] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
- <6>[ 3.400853] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
- <6>[ 3.402068] tegra-xudc-new 700d0000.xudc: device count: 1
- <6>[ 3.403105] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
- <6>[ 3.403112] tegra-xudc-new 700d0000.xudc: vbus state: 1
- <6>[ 3.403121] tegra-xudc-new 700d0000.xudc: device mode on: 0
- <6>[ 3.403128] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
- <6>[ 3.403149] tegra-xudc-new 700d0000.xudc: active: 0 => 1
- <6>[ 3.403634] mousedev: PS/2 mouse device common for all mice
- <6>[ 3.403952] usbcore: registered new interface driver xpad
- <6>[ 3.403996] usbcore: registered new interface driver usb_acecad
- <6>[ 3.404035] usbcore: registered new interface driver aiptek
- <6>[ 3.404073] usbcore: registered new interface driver gtco
- <6>[ 3.404113] usbcore: registered new interface driver hanwang
- <6>[ 3.404150] usbcore: registered new interface driver kbtab
- <6>[ 3.499541] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc 0
- <6>[ 3.501664] rtc rtc1: alarm rtc device
- <6>[ 3.501679] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as 1
- <5>[ 3.501702] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
- <6>[ 3.502038] usb usb2: usb_suspend_both: status 0
- <6>[ 3.502129] i2c /dev entries driver
- <6>[ 3.503255] IR NEC protocol handler initialized
- <6>[ 3.503721] usbcore: registered new interface driver uvcvideo
- <6>[ 3.503723] USB Video Class driver (1.1.1)
- <6>[ 3.503957] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
- <6>[ 3.506058] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, mi2
- <6>[ 3.506062] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min4
- <6>[ 3.506438] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.506450] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down wC
- <6>[ 3.506458] tegra_soctherm 700e2000.soctherm: throttrip: will throttle whC
- <6>[ 3.506621] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.506631] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down wC
- <6>[ 3.506638] tegra_soctherm 700e2000.soctherm: throttrip: will throttle whC
- <6>[ 3.506827] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.506835] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down wC
- <6>[ 3.506839] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hote
- <6>[ 3.507109] tegra_soctherm 700e2000.soctherm: failed to register sensor: 9
- <6>[ 3.507720] tegra_aotag tegra-aotag: Registering sensor 0
- <6>[ 3.507779] tegra_aotag tegra-aotag: Invalid temp readout
- <6>[ 3.507801] tegra_aotag tegra-aotag: Invalid temp readout
- <6>[ 3.507819] tegra_aotag tegra-aotag: Bound to TZ : ID 0
- <6>[ 3.507827] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
- <6>[ 3.508723] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.508738] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling devid
- <6>[ 3.508898] tegra_aotag tegra-aotag: Invalid temp readout
- <6>[ 3.508923] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling d
- <6>[ 3.509353] parse_throttle_dt_data: Num cap clks = 5
- <6>[ 3.509357] parse_throttle_dt_data: clk=cclk_g type=2
- <6>[ 3.509364] parse_throttle_dt_data: clk=gpu type=4
- <6>[ 3.509383] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
- <6>[ 3.509398] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
- <6>[ 3.509416] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
- <6>[ 3.509714] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.509797] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.509910] tegra_throttle_probe: probe successful. #cdevs=4
- <6>[ 3.511040] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, )
- <6>[ 3.511824] device-mapper: uevent: version 1.0.3
- <6>[ 3.512271] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: m
- <6>[ 3.512347] device-mapper: verity-avb: AVB error handler initialized with
- <6>[ 3.512351] Bluetooth: HCI UART driver ver 2.3
- <6>[ 3.512355] Bluetooth: HCI UART protocol LL registered
- <6>[ 3.515410] tegra210-cpufreq cpufreq: probe()...completed
- <6>[ 3.516349] sdhci: Secure Digital Host Controller Interface driver
- <6>[ 3.516350] sdhci: Copyright(c) Pierre Ossman
- <6>[ 3.516402] sdhci-pltfm: SDHCI platform and OF driver helper
- <6>[ 3.516951] sdhci-tegra sdhci-tegra.0: Got CD GPIO
- <6>[ 3.517402] sdhci-tegra sdhci-tegra.0: Client registration for eMC Succesl
- <6>[ 3.517537] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 301
- <6>[ 3.520357] hidraw: raw HID events driver (C) Jiri Kosina
- <6>[ 3.522181] usbcore: registered new interface driver usbhid
- <6>[ 3.522182] usbhid: USB HID core driver
- <6>[ 3.522529] ashmem: initialized
- <6>[ 3.523587] tegra21x_actmon 6000c800.actmon: in actmon_register()...
- <6>[ 3.523653] tegra21x_actmon 6000c800.actmon: bwmgr_disable = 0
- <6>[ 3.523769] tegra21x_actmon 6000c800.actmon: initialization Completed forl
- <6>[ 3.526484] tegra_hv: get_hvd: not initialized yet
- <6>[ 3.526488] user_ivc_mempool: hypervisor not present
- <6>[ 3.526703] usbcore: registered new interface driver snd-usb-audio
- <6>[ 3.526759] No Device Node present for smmu client: snd-soc-dummy !!
- <5>[ 3.526764] platform snd-soc-dummy: No iommus property found in DT node, )
- <6>[ 3.526780] iommu: Adding device snd-soc-dummy to group 36
- <6>[ 3.527886] sch_tegra_init
- <6>[ 3.527888] u32 classifier
- <6>[ 3.527889] Actions configured
- <6>[ 3.527893] Netfilter messages via NETLINK v0.30.
- <6>[ 3.528115] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- <6>[ 3.528267] ctnetlink v0.93: registering with nfnetlink.
- <6>[ 3.528598] xt_time: kernel timezone is -0000
- <6>[ 3.528670] IPv4 over IPsec tunneling driver
- <6>[ 3.546658] ip_tables: (C) 2000-2006 Netfilter Core Team
- <6>[ 3.546774] arp_tables: arp_tables: (C) 2002 David S. Miller
- <6>[ 3.558517] Initializing XFRM netlink socket
- <6>[ 3.559274] NET: Registered protocol family 10
- <6>[ 3.560061] mip6: Mobile IPv6
- <6>[ 3.560073] ip6_tables: (C) 2000-2006 Netfilter Core Team
- <6>[ 3.562534] tegra-pcie 1003000.pcie: link 0 down, retrying
- <6>[ 3.571063] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
- <6>[ 3.571617] NET: Registered protocol family 17
- <6>[ 3.571630] NET: Registered protocol family 15
- <6>[ 3.571708] bridge: filtering via arp/ip/ip6tables is no longer available.
- <6>[ 3.571711] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- <6>[ 3.571717] Bluetooth: HIDP socket layer initialized
- <6>[ 3.571718] 8021q: 802.1Q VLAN Support v1.8
- <5>[ 3.571738] Key type dns_resolver registered
- <6>[ 3.573124] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] usingr
- <5>[ 3.576618] Registered cp15_barrier emulation handler
- <5>[ 3.576626] Registered setend emulation handler
- <6>[ 3.578926] registered taskstats version 1
- <6>[ 3.581585] isp 54600000.isp: initialized
- <6>[ 3.582603] isp 54680000.isp: initialized
- <6>[ 3.595022] last reset is due to software reset
- <6>[ 3.595024] KERNEL: PMC reset status reg: 0x3
- <6>[ 3.595074] BL: PMC reset status reg: 0x3
- <6>[ 3.595075] BL: PMIC poweroff Event Recorder: 0x0
- <6>[ 3.595626] vdd-wlreg_on: 1800 mV
- <6>[ 3.597312] clk_cbus_recalc_rate: no gbus parent
- <6>[ 3.597316] clk_cbus_round_rate: no gbus parent
- <6>[ 3.597318] clk_cbus_round_rate: no gbus parent
- <6>[ 3.597324] clk_cbus_recalc_rate: no gbus parent
- <6>[ 3.597421] clk_cbus_recalc_rate: no gbus parent
- <6>[ 3.597424] clk_cbus_round_rate: no gbus parent
- <6>[ 3.597425] clk_cbus_round_rate: no gbus parent
- <6>[ 3.597428] clk_cbus_recalc_rate: no gbus parent
- <6>[ 3.598109] tegra_dvfs: GPU-cap: registered
- <6>[ 3.598167] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19d
- <6>[ 3.598169] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 1d
- <6>[ 3.598171] tegra dvfs: vdd-gpu: nominal 1048mV, offset 708000uV, step 10d
- <6>[ 3.599624] tegra_dvfs: vdd-gpu-vts: registered
- <6>[ 3.600359] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'flood
- <6>[ 3.601125] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cod
- <6>[ 3.601609] input: gpio-keys as /devices/gpio-keys/input/input0
- <6>[ 3.609238] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
- <6>[ 3.636535] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-10 01)
- <6>[ 3.637712] vi 54080000.vi: vi_probe: ++
- <6>[ 3.641509] vi 54080000.vi: initialized
- <6>[ 3.644525] vi 54080000.vi: subdev nvcsi--1 bound
- <6>[ 3.645743] Disable partitions left on by BL
- <6>[ 3.645746] disb
- <6>[ 3.645912] bwmgr: missing cdev-type property
- <6>[ 3.646255] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 0
- <6>[ 3.646261] DRAM derating cdev registered.
- <6>[ 3.647164] hvc_sysfs: hypervisor is not present
- <6>[ 3.647668] vdd-fan: disabling
- <6>[ 3.647671] vdd-usb-vbus: disabling
- <6>[ 3.647672] vdd-usb-vbus2: disabling
- <6>[ 3.647682] avdd-io-edp-1v05: disabling
- <6>[ 3.647788] ALSA device list:
- <6>[ 3.647790] No soundcards found.
- <6>[ 3.729052] usb 1-2: new high-speed USB device number 2 using tegra-xusb
- <6>[ 3.765559] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
- <6>[ 3.765562] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumb0
- <6>[ 3.765565] usb 1-2: Product: 4-Port USB 2.1 Hub
- <6>[ 3.765567] usb 1-2: Manufacturer: Generic
- <6>[ 3.767256] hub 1-2:1.0: USB hub found
- <6>[ 3.768100] mmc0: hw tuning done ...
- <6>[ 3.768148] mmc0: new ultra high speed SDR104 SDXC card at address 1234
- <6>[ 3.768346] hub 1-2:1.0: 4 ports detected
- <6>[ 3.768496] mmcblk0: mmc0:1234 SA64G 58.0 GiB
- <6>[ 3.772862] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 6
- <6>[ 3.877865] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
- <6>[ 3.912309] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
- <6>[ 3.912313] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumb0
- <6>[ 3.912315] usb 2-1: Product: 4-Port USB 3.1 Hub
- <6>[ 3.912317] usb 2-1: Manufacturer: Generic
- <6>[ 3.917709] hub 2-1:1.0: USB hub found
- <6>[ 3.919233] hub 2-1:1.0: 4 ports detected
- <6>[ 3.922365] tegra_cec 70015000.tegra_cec: physical address: 10:00.
- <6>[ 3.973485] tegra-pcie 1003000.pcie: link 0 down, retrying
- <5>[ 3.990293] tegra_cec 70015000.tegra_cec: Sent <Text View On> res: -113.
- <5>[ 3.990296] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
- <6>[ 4.057050] usb 1-2.4: new low-speed USB device number 3 using tegra-xusb
- <6>[ 4.083974] usb 1-2.4: New USB device found, idVendor=046d, idProduct=c317
- <6>[ 4.083977] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNu0
- <6>[ 4.083980] usb 1-2.4: Product: USB Multimedia Keyboard
- <6>[ 4.083982] usb 1-2.4: Manufacturer: Logitech
- <6>[ 4.088337] input: Logitech USB Multimedia Keyboard as /devices/70090000.1
- <6>[ 4.145459] hid-generic 0003:046D:C317.0001: input,hidraw0: USB HID v1.100
- <6>[ 4.151481] input: Logitech USB Multimedia Keyboard as /devices/70090000.2
- <6>[ 4.151631] hid-generic 0003:046D:C317.0002: input,hidraw1: USB HID v1.101
- <6>[ 4.217297] usb 2-1.1: new SuperSpeed USB device number 3 using tegra-xusb
- <6>[ 4.238200] usb 2-1.1: New USB device found, idVendor=152d, idProduct=0562
- <6>[ 4.238203] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNu3
- <6>[ 4.238206] usb 2-1.1: Product: External
- <6>[ 4.238208] usb 2-1.1: Manufacturer: JMicron
- <6>[ 4.238210] usb 2-1.1: SerialNumber: DD56419883893
- <6>[ 4.239015] usb-storage 2-1.1:1.0: USB Mass Storage device detected
- <6>[ 4.239235] scsi host0: usb-storage 2-1.1:1.0
- <6>[ 4.382008] tegra-pcie 1003000.pcie: link 0 down, retrying
- <6>[ 4.384075] tegra-pcie 1003000.pcie: link 0 down, ignoring
- <6>[ 4.488492] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
- <6>[ 4.488496] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
- <6>[ 4.488499] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
- <6>[ 4.488501] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff]
- <6>[ 4.488504] pci_bus 0000:00: root bus resource [bus 00-ff]
- <6>[ 4.488727] iommu: Adding device 0000:00:02.0 to group 37
- <6>[ 4.488814] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]),g
- <6>[ 4.489301] iommu: Adding device 0000:01:00.0 to group 38
- <6>[ 4.497151] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
- <6>[ 4.497154] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
- <6>[ 4.497160] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff ]
- <6>[ 4.497177] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff ]
- <6>[ 4.497193] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
- <6>[ 4.497200] pci 0000:00:02.0: PCI bridge to [bus 01]
- <6>[ 4.497203] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
- <6>[ 4.497207] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
- <6>[ 4.497439] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrut
- <6>[ 4.497442] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
- <6>[ 5.118602] Extcon HDMI: HPD enabled
- <6>[ 5.118626] tegradc tegradc.0: hdmi: plugged
- <6>[ 5.118645] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
- <6>[ 5.118649] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
- <6>[ 5.143364] Freeing unused kernel memory: 7936K
- <14>[ 5.178110] init: init first stage started!
- <14>[ 5.182753] init: Unable to open /lib/modules, skipping module loading.
- <14>[ 5.189746] init: First stage mount skipped (recovery mode)
- <14>[ 5.196494] init: Using Android DT directory /proc/device-tree/firmware//
- <14>[ 5.204351] init: Skipped setting INIT_AVB_VERSION (not vbmeta compatibl)
- <5>[ 5.212915] random: init: uninitialized urandom read (40 bytes read)
- <5>[ 5.229667] random: init: uninitialized urandom read (40 bytes read)
- <5>[ 5.236415] random: init: uninitialized urandom read (4 bytes read)
- <11>[ 5.253773] init: Could not find mount entry for /system
- <14>[ 5.259505] init: Loading SELinux policy
- <5>[ 5.265822] scsi 0:0:0:0: Direct-Access JMicron Tech 0206
- <5>[ 5.274919] sd 0:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB)
- <5>[ 5.283345] sd 0:0:0:0: [sda] Write Protect is off
- <5>[ 5.288917] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, A
- <5>[ 5.373128] audit: type=1403 audit(947468280.235:2): policy loaded auid=45
- <14>[ 5.382450] selinux: SELinux: Loaded policy from /sepolicy
- <14>[ 5.388303] selinux:
- <5>[ 5.391230] audit: type=1404 audit(947468280.255:3): enforcing=1 old_enfo5
- <14>[ 5.424389] selinux: SELinux: Loaded file_contexts
- <14>[ 5.429557] selinux:
- <14>[ 5.456069] init: init second stage started!
- <14>[ 5.494975] init: Using Android DT directory /proc/device-tree/firmware//
- <12>[ 5.503934] init: Couldn't load property file '/system/etc/prop.default'y
- <12>[ 5.520767] init: Couldn't load property file '/system/build.prop': openy
- <12>[ 5.533374] init: Couldn't load property file '/system_ext/build.prop': y
- <12>[ 5.546267] init: Couldn't load property file '/vendor/default.prop': opy
- <12>[ 5.558996] init: Couldn't load property file '/vendor/build.prop': openy
- <12>[ 5.571569] init: Couldn't load property file '/odm/etc/build.prop': opey
- <12>[ 5.584203] init: Couldn't load property file '/product/build.prop': opey
- <12>[ 5.596829] init: Couldn't load property file '/factory/factory.prop': oy
- <5>[ 5.632274] audit: type=1400 audit(947468280.491:4): avc: denied { read0
- <5>[ 5.676026] audit: type=1400 audit(947468280.535:5): avc: denied { sys_0
- <14>[ 5.694492] ueventd: ueventd started!
- <14>[ 5.701863] selinux: SELinux: Loaded file_contexts
- <14>[ 5.707027] selinux:
- <14>[ 5.709750] ueventd: Parsing file /system/etc/ueventd.rc...
- <14>[ 5.716001] ueventd: Parsing file /vendor/ueventd.rc...
- <14>[ 5.721614] ueventd: Unable to read config file '/vendor/ueventd.rc': opy
- <14>[ 5.731987] ueventd: Parsing file /odm/ueventd.rc...
- <14>[ 5.737329] ueventd: Unable to read config file '/odm/ueventd.rc': open(y
- <14>[ 5.747428] ueventd: Parsing file /ueventd.porg_sd.rc...
- <14>[ 5.753116] ueventd: Unable to read config file '/ueventd.porg_sd.rc': oy
- <4>[ 7.275332] GPT:Primary header thinks Alt. header is not at the end of th.
- <4>[ 7.283003] GPT:121602047 != 1000215215
- <4>[ 7.287097] GPT:Alternate GPT header not at the end of the disk.
- <4>[ 7.293360] GPT:121602047 != 1000215215
- <4>[ 7.297456] GPT: Use GNU Parted to correct GPT errors.
- <6>[ 7.302880] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda16
- <5>[ 7.315690] sd 0:0:0:0: [sda] Attached SCSI disk
- <6>[ 7.553286] file system registered
- <12>[ 7.576653] charger: Charger uses system defaults.
- <12>[ 7.582092] healthd: No battery devices found
- <5>[ 7.586958] audit: type=1400 audit(947468282.451:6): avc: denied { wake0
- <5>[ 7.597932] audit: type=1400 audit(947468282.451:7): avc: denied { sear1
- <5>[ 7.597959] audit: type=1400 audit(947468282.451:8): avc: denied { read1
- <5>[ 7.597979] audit: type=1400 audit(947468282.451:9): avc: denied { open1
- <11>[ 7.668053] HealthLoop: wakealarm_init: timerfd_create failed
- <12>[ 7.674319] healthd: battery none chg=
- <6>[ 8.653169] EXT4-fs (sda10): mounted filesystem with ordered data mode. Oc
- <5>[ 8.664488] audit: type=1107 audit(947468283.523:10): pid=1 uid=0 auid=42'
- <6>[ 8.796184] tegradc tegradc.0: blank - powerdown
- <6>[ 8.846184] extcon-disp-state extcon:disp-state: cable 47 state 0
- <6>[ 8.846185] Extcon AUX1(HDMI) disable
- <6>[ 8.881680] tegradc tegradc.0: unblank
- <6>[ 8.907370] tegradc tegradc.0: nominal-pclk:148351648 parent:148350000 di4
- <6>[ 8.907424] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_m
- <6>[ 8.908357] tegradc tegradc.0: hdmi: get RGB quant from EDID.
- <6>[ 8.908363] tegradc tegradc.0: hdmi: get YCC quant from EDID.
- <6>[ 8.911654] extcon-disp-state extcon:disp-state: cable 47 state 1
- <6>[ 8.911656] Extcon AUX1(HDMI) enable
- <6>[ 8.978678] tegradc tegradc.0: nominal-pclk:148351648 parent:148350000 di4
- <4>[ 9.117722] EXT4-fs (sda16): Ignoring removed nomblk_io_submit option
- <6>[ 9.131782] EXT4-fs (sda16): mounted filesystem with ordered data mode. Ot
- <5>[ 9.162140] audit: type=1107 audit(947468284.023:11): pid=1 uid=0 auid=42'
- <6>[ 9.199274] EXT4-fs (sda16): mounted filesystem with ordered data mode. Oc
- <5>[ 9.234812] audit: type=1107 audit(947468284.095:12): pid=1 uid=0 auid=42'
- <6>[ 9.295426] read descriptors
- <6>[ 9.298615] read strings
- <6>[ 9.303214] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled
- <6>[ 9.326032] EXT4-fs (sda16): mounted filesystem with ordered data mode. Oc
- <5>[ 9.366630] audit: type=1400 audit(947468284.227:13): avc: denied { rea1
- <5>[ 9.386878] audit: type=1400 audit(947468284.247:14): avc: denied { ope1
- <5>[ 9.407817] audit: type=1400 audit(947468284.271:15): avc: denied { rea1
- <5>[ 9.428797] audit: type=1400 audit(947468284.291:16): avc: denied { ope1
- <5>[ 9.452113] audit: type=1400 audit(947468284.311:17): avc: denied { wri1
- <5>[ 9.473326] audit: type=1400 audit(947468284.335:18): avc: denied { ope1
- <5>[ 9.500474] audit: type=1400 audit(947468284.359:19): avc: denied { rea1
- <5>[ 18.210196] random: crng init done
- <5>[ 18.213855] random: 7 urandom warning(s) missed due to ratelimiting
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement