Advertisement
Guest User

Goldie Lin

a guest
Jul 15th, 2010
146
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 14.68 KB | None | 0 0
  1. 40W
  2.  
  3. Texas Instruments X-Loader 1.41
  4. Starting on with MMC
  5. Reading boot sector
  6.  
  7. 200488 Bytes Read from MMC
  8. Starting OS Bootloader from MMC...
  9.  
  10.  
  11. U-Boot 2010.06 (Jun 30 2010 - 17:35:57)
  12.  
  13. OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
  14. OMAP3 DevKit8000 + LPDDR/NAND
  15. I2C: ready
  16. DRAM: 256 MiB
  17. NAND: 256 MiB
  18. *** Warning - bad CRC or NAND, using default environment
  19.  
  20. In: serial
  21. Out: serial
  22. Err: serial
  23. ethaddr not set, using Die ID
  24. Die ID #0614000400000000040364320e01301a
  25. Net: dm9000
  26. Hit any key to stop autoboot: 0
  27. mmc0 is available
  28. reading boot.scr
  29.  
  30. 294 bytes read
  31. Running bootscript from mmc ...
  32. ## Executing script at 82000000
  33. mmc0 is available
  34. reading uImage
  35.  
  36. 2290168 bytes read
  37. ## Booting kernel from Legacy Image at 80300000 ...
  38. Image Name: Linux-2.6.35-rc3-g85fd48a-dirty
  39. Image Type: ARM Linux Kernel Image (uncompressed)
  40. Data Size: 2290104 Bytes = 2.2 MiB
  41. Load Address: 80008000
  42. Entry Point: 80008000
  43. Verifying Checksum ... OK
  44. Loading Kernel Image ... OK
  45. OK
  46.  
  47. Starting kernel ...
  48.  
  49. [ 0.000000] Linux version 2.6.35-rc3-g85fd48a-dirty (cvlsi@cvgr) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 Thu Jul 8 17:27:03 CST 2010
  50. [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
  51. [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  52. [ 0.000000] Machine: OMAP3 Devkit8000
  53. [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
  54. [ 0.000000] Memory policy: ECC disabled, Data cache writeback
  55. [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
  56. [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
  57. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
  58. [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rootfstype=ext3 rw rootwait vram=12M omapdss.def_disp=lcd omapfb.mode=lcd:800x480
  59. [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  60. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  61. [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  62. [ 0.000000] Memory: 128MB 128MB = 256MB total
  63. [ 0.000000] Memory: 242960k/242960k available, 19184k reserved, 0K highmem
  64. [ 0.000000] Virtual kernel memory layout:
  65. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  66. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  67. [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
  68. [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
  69. [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
  70. [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
  71. [ 0.000000] .init : 0xc0008000 - 0xc0031000 ( 164 kB)
  72. [ 0.000000] .text : 0xc0031000 - 0xc0413000 (3976 kB)
  73. [ 0.000000] .data : 0xc0432000 - 0xc0466940 ( 211 kB)
  74. [ 0.000000] Hierarchical RCU implementation.
  75. [ 0.000000] RCU-based detection of stalled CPUs is disabled.
  76. [ 0.000000] Verbose stalled-CPUs detection is disabled.
  77. [ 0.000000] NR_IRQS:402
  78. [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/266/500 MHz
  79. [ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
  80. [ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
  81. [ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
  82. [ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
  83. [ 0.000000] Reprogramming SDRC clock to 266000000 Hz
  84. [ 0.000000] dpll3_m2_clk rate change failed: -22
  85. [ 0.000000] GPMC revision 5.0
  86. [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
  87. [ 0.000000] Total of 96 interrupts on 1 active controller
  88. [ 0.000000] OMAP GPIO hardware version 2.5
  89. [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
  90. [ 0.000000] Console: colour dummy device 80x30
  91. [ 0.000000] Calibrating delay loop... 492.62 BogoMIPS (lpj=1925120)
  92. [ 0.000000] pid_max: default: 32768 minimum: 301
  93. [ 0.000000] Mount-cache hash table entries: 512
  94. [ 0.000000] CPU: Testing write buffer coherency: ok
  95. [ 0.000000] devtmpfs: initialized
  96. [ 0.000000] regulator: core version 0.5
  97. [ 0.000000] NET: Registered protocol family 16
  98. [ 0.000000] Found NAND on CS0
  99. [ 0.000000] Registering NAND on CS0
  100. [ 10.608673] OMAP DMA hardware revision 4.0
  101. [ 10.626495] bio: create slab <bio-0> at 0
  102. [ 10.629241] SCSI subsystem initialized
  103. [ 10.631683] usbcore: registered new interface driver usbfs
  104. [ 10.631927] usbcore: registered new interface driver hub
  105. [ 10.632202] usbcore: registered new device driver usb
  106. [ 10.633087] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
  107. [ 10.636657] twl4030: PIH (irq 7) chaining IRQs 368..375
  108. [ 10.636688] twl4030: power (irq 373) chaining IRQs 376..383
  109. [ 10.637298] twl4030: gpio (irq 368) chaining IRQs 384..401
  110. [ 10.640869] regulator: VUSB1V5: 1500 mV normal standby
  111. [ 10.641510] regulator: VUSB1V8: 1800 mV normal standby
  112. [ 10.642150] regulator: VUSB3V1: 3100 mV normal standby
  113. [ 10.644073] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
  114. [ 10.645446] regulator: VPLL1: 1800 mV normal standby
  115. [ 10.647308] regulator: VIO: 1800 mV normal standby
  116. [ 10.648071] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
  117. [ 10.648712] regulator: VDAC: 1800 mV normal standby
  118. [ 10.648956] i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
  119. [ 10.650817] Advanced Linux Sound Architecture Driver Version 1.0.23.
  120. [ 10.651702] Switching to clocksource 32k_counter
  121. [ 10.654327] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
  122. [ 10.657165] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
  123. [ 10.657714] NET: Registered protocol family 2
  124. [ 10.657928] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  125. [ 10.658996] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  126. [ 10.659271] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
  127. [ 10.659454] TCP: Hash tables configured (established 8192 bind 8192)
  128. [ 10.659484] TCP reno registered
  129. [ 10.659484] UDP hash table entries: 256 (order: 0, 4096 bytes)
  130. [ 10.659545] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  131. [ 10.659820] NET: Registered protocol family 1
  132. [ 10.660247] RPC: Registered udp transport module.
  133. [ 10.660247] RPC: Registered tcp transport module.
  134. [ 10.660278] RPC: Registered tcp NFSv4.1 backchannel transport module.
  135. [ 10.661071] PMU: registered new PMU device of type 0
  136. [ 10.661315] NetWinder Floating Point Emulator V0.97 (double precision)
  137. [ 10.663238] VFS: Disk quotas dquot_6.5.2
  138. [ 10.663330] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  139. [ 10.664611] JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc.
  140. [ 10.665222] msgmni has been set to 474
  141. [ 10.669067] alg: No test for stdrng (krng)
  142. [ 10.669189] io scheduler noop registered
  143. [ 10.669219] io scheduler deadline registered
  144. [ 10.669372] io scheduler cfq registered (default)
  145. [ 10.730194] OMAP DSS rev 2.0
  146. [ 10.730316] OMAP DISPC rev 3.0
  147. [ 10.730346] OMAP VENC rev 2
  148. [ 11.081298] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  149. [ 11.103729] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
  150. [ 11.124572] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
  151. [ 11.145233] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
  152. [ 11.707489] console [ttyS2] enabled
  153. [ 11.724060] brd: module loaded
  154. [ 11.733886] loop: module loaded
  155. [ 11.739562] omap2-nand driver initializing
  156. [ 11.743957] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
  157. [ 11.753051] cmdlinepart partition parsing not available
  158. [ 11.758392] Creating 5 MTD partitions on "omap2-nand.0":
  159. [ 11.763763] 0x000000000000-0x000000080000 : "X-Loader"
  160. [ 11.771087] 0x000000080000-0x000000260000 : "U-Boot"
  161. [ 11.778656] 0x000000260000-0x000000280000 : "U-Boot Env"
  162. [ 11.785888] 0x000000280000-0x000000680000 : "Kernel"
  163. [ 11.794281] 0x000000680000-0x000010000000 : "File System"
  164. [ 11.903991] dm9000 Ethernet Driver, V1.31
  165. [ 11.996459] eth0: dm9000a at d08c0000,d08c4400 IRQ 185 MAC: 02:32:0e:01:30:1a (platform data)
  166. [ 12.005371] usbmon: debugfs is not available
  167. [ 12.009643] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  168. [ 12.016723] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
  169. [ 12.022521] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
  170. [ 12.030181] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
  171. [ 12.050231] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
  172. [ 12.056182] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  173. [ 12.063049] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  174. [ 12.070343] usb usb1: Product: OMAP-EHCI Host Controller
  175. [ 12.075714] usb usb1: Manufacturer: Linux 2.6.35-rc3-g85fd48a-dirty ehci_hcd
  176. [ 12.082824] usb usb1: SerialNumber: ehci-omap.0
  177. [ 12.088592] hub 1-0:1.0: USB hub found
  178. [ 12.092437] hub 1-0:1.0: 3 ports detected
  179. [ 12.120849] g_ether gadget: using random self ethernet address
  180. [ 12.126739] g_ether gadget: using random host ethernet address
  181. [ 12.133361] usb0: MAC 8e:2a:52:6f:33:49
  182. [ 12.137298] usb0: HOST MAC 2e:44:36:7a:4d:2e
  183. [ 12.141754] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
  184. [ 12.148468] g_ether gadget: g_ether ready
  185. [ 12.152526] musb_hdrc musb_hdrc: MUSB HDRC host driver
  186. [ 12.157745] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
  187. [ 12.165191] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  188. [ 12.172058] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  189. [ 12.179351] usb usb2: Product: MUSB HDRC host driver
  190. [ 12.184356] usb usb2: Manufacturer: Linux 2.6.35-rc3-g85fd48a-dirty musb-hcd
  191. [ 12.191497] usb usb2: SerialNumber: musb_hdrc
  192. [ 12.197143] hub 2-0:1.0: USB hub found
  193. [ 12.201019] hub 2-0:1.0: 1 port detected
  194. [ 12.206726] input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0
  195. [ 12.218505] ads7846 spi2.0: touchscreen, irq 187
  196. [ 12.224060] input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.2/spi2.0/input/input1
  197. [ 12.233856] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
  198. [ 12.240173] twl_rtc twl_rtc: Power up reset detected.
  199. [ 12.245727] twl_rtc twl_rtc: Enabling TWL-RTC.
  200. [ 12.250732] i2c /dev entries driver
  201. [ 12.255798] sdhci: Secure Digital Host Controller Interface driver
  202. [ 12.262084] sdhci: Copyright(c) Pierre Ossman
  203. [ 12.271972] usbcore: registered new interface driver usbhid
  204. [ 12.277679] usbhid: USB HID core driver
  205. [ 12.370513] No device for DAI omap-mcbsp-dai-0
  206. [ 12.375030] No device for DAI omap-mcbsp-dai-1
  207. [ 12.379547] No device for DAI omap-mcbsp-dai-2
  208. [ 12.384033] No device for DAI omap-mcbsp-dai-3
  209. [ 12.388519] No device for DAI omap-mcbsp-dai-4
  210. [ 12.392974] OMAP3 Beagle/Devkit8000 SoC init
  211. [ 12.399383] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
  212. [ 12.408782] ALSA device list:
  213. [ 12.411865] #0: omap3beagle (twl4030)
  214. [ 12.415985] TCP cubic registered
  215. [ 12.419311] NET: Registered protocol family 17
  216. [ 12.423858] NET: Registered protocol family 15
  217. [ 12.428405] ThumbEE CPU extension supported.
  218. [ 12.433319] Power Management for TI OMAP3.
  219. [ 12.437744] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
  220. [ 12.445648] usb 1-1: new high speed USB device using ehci-omap and address 2
  221. [ 12.480773] Console: switching to colour frame buffer device 100x30
  222. [ 12.502960] regulator_init_complete: incomplete constraints, leaving VDAC on
  223. [ 12.510772] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
  224. [ 12.535003] Waiting for root device /dev/mmcblk0p2...
  225. [ 12.573394] mmc0: new high speed SDHC card at address b368
  226. [ 12.579589] mmcblk0: mmc0:b368 SDC 3.84 GiB
  227. [ 12.584503] mmcblk0: p1 p2 p3
  228. [ 12.630279] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
  229. [ 12.637054] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
  230. [ 12.644287] usb 1-1: Product: USB2.0 Hub
  231. [ 12.650390] hub 1-1:1.0: USB hub found
  232. [ 12.654632] hub 1-1:1.0: 4 ports detected
  233. [ 12.661285] EXT3-fs: barriers not enabled
  234. [ 12.667205] kjournald starting. Commit interval 5 seconds
  235. [ 12.676361] EXT3-fs (mmcblk0p2): using internal journal
  236. [ 12.681640] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
  237. [ 12.688842] VFS: Mounted root (ext3 filesystem) on device 179:2.
  238. [ 12.697784] devtmpfs: mounted
  239. [ 12.700866] Freeing init memory: 164K
  240. [ 12.949157] usb 1-1.3: new low speed USB device using ehci-omap and address 3
  241. [ 13.092803] usb 1-1.3: New USB device found, idVendor=046e, idProduct=5540
  242. [ 13.099792] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  243. [ 13.107238] usb 1-1.3: Product: USB Multimedia Keyboard
  244. [ 13.112518] usb 1-1.3: Manufacturer: BTC
  245. [ 13.140045] input: BTC USB Multimedia Keyboard as /devices/platform/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input2
  246. [ 13.152893] generic-usb 0003:046E:5540.0001: input: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-ehci-omap.0-1.3/input0
  247. [ 13.196014] input: BTC USB Multimedia Keyboard as /devices/platform/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.1/input/input3
  248. [ 13.208221] generic-usb 0003:046E:5540.0002: input: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-ehci-omap.0-1.3/input1
  249. [ 13.301116] usb 1-1.4: new low speed USB device using ehci-omap and address 4
  250. [ 13.430999] usb 1-1.4: New USB device found, idVendor=04b3, idProduct=310c
  251. [ 13.438049] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
  252. [ 13.445556] usb 1-1.4: Product: USB Optical Mouse
  253. [ 13.460510] input: USB Optical Mouse as /devices/platform/ehci-omap.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input4
  254. [ 13.472808] generic-usb 0003:04B3:310C.0003: input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-ehci-omap.0-1.4/input0
  255. init: ureadahead main process (485) terminated with status 5
  256. init: procps main process (520) terminated with status 255
  257. Starting PVR
  258. FATAL: Error inserting omaplfb (/lib/modules/2.6.35-rc3-g85fd48a-dirty/kernel/drivers/staging/omap3-sgx/services4/3rdparty/dc_omap3430_linux/omaplfb.ko): Invalid module format
  259. FATAL: Error inserting bufferclass_ti (/lib/modules/2.6.35-rc3-g85fd48a-dirty/kernel/drivers/staging/omap3-sgx/services4/3rdparty/bufferclass_ti/bufferclass_ti.ko): Invalid module format
  260. mknod: missing operand after `0'
  261. Try `mknod --help' for more information.
  262. chmod: cannot access `/dev/pvrsrvkm': No such file or directory
  263. mknod: missing operand after `0'
  264. Try `mknod --help' for more information.
  265. chmod: cannot access `/dev/bc_cat': No such file or directory
  266.  
  267. Ubuntu 10.04.1 LTS SBC8100 ttyS2
  268.  
  269. SBC8100 login:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement