Guest User

Untitled

a guest
Jul 21st, 2013
125
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. [ 0.000000] Linux version 3.9.8 (pepe@debian) (gcc version 4.8.1 (OpenWrt/Linaro GCC 4.8-2013.04 r37180) ) #2 SMP Sun Jul 21 13:34:40 CEST 2013
  2. [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
  3. [ 0.000000] CPU frequency is 400 MHz
  4. [ 0.000000] 64MB of RAM installed
  5. [ 0.000000] registering 38 GPIOs
  6. [ 0.000000] board_bcm963xx: Boot address 0xb8000000
  7. [ 0.000000] board_bcm963xx: CFE version: 1.0.37-110.11-1
  8. [ 0.000000] bootconsole [early0] enabled
  9. [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
  10. [ 0.000000] board_bcm963xx: board name: 96368M-1541N
  11. [ 0.000000] Determined physical RAM map:
  12. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  13. [ 0.000000] Initrd not found or empty - disabling initrd
  14. [ 0.000000] Zone ranges:
  15. [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
  16. [ 0.000000] Movable zone start for each node
  17. [ 0.000000] Early memory node ranges
  18. [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
  19. [ 0.000000] On node 0 totalpages: 16384
  20. [ 0.000000] free_area_init_node: node 0, pgdat 80314a20, node_mem_map 81000000
  21. [ 0.000000] Normal zone: 128 pages used for memmap
  22. [ 0.000000] Normal zone: 0 pages reserved
  23. [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
  24. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
  25. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  26. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6496 r8192 d13984 u32768
  27. [ 0.000000] pcpu-alloc: s6496 r8192 d13984 u32768 alloc=8*4096
  28. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
  29. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  30. [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  31. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  32. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  33. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  34. [ 0.000000] __ex_table already sorted, skipping sort
  35. [ 0.000000] Memory: 61144k/65536k available (2541k kernel code, 4392k reserved, 628k data, 284k init, 0k highmem)
  36. [ 0.000000] Hierarchical RCU implementation.
  37. [ 0.000000] NR_IRQS:128
  38. [ 0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
  39. [ 0.032000] pid_max: default: 32768 minimum: 301
  40. [ 0.036000] Mount-cache hash table entries: 512
  41. [ 0.044000] SMP: Booting CPU1...
  42. [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
  43. [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
  44. [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  45. [ 0.080000] SMP: CPU1 is running
  46. [ 0.080000] Brought up 2 CPUs
  47. [ 0.116000] NET: Registered protocol family 16
  48. [ 0.128000] registering PCI controller with io_map_base unset
  49. [ 0.144000] bio: create slab <bio-0> at 0
  50. [ 0.148000] PCI host bridge to bus 0000:00
  51. [ 0.152000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
  52. [ 0.156000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
  53. [ 0.160000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  54. [ 0.164000] pci 0000:00:01.0: [14e4:a8d6] type 00 class 0x028000
  55. [ 0.164000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff]
  56. [ 0.176000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
  57. [ 0.176000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
  58. [ 0.180000] Switching to clocksource MIPS
  59. [ 0.192000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
  60. [ 0.200000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
  61. [ 0.220000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
  62. [ 0.228000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243)
  63. [ 0.228000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
  64. [ 0.228000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
  65. [ 0.284000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
  66. [ 0.292000] NET: Registered protocol family 2
  67. [ 0.300000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
  68. [ 0.308000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
  69. [ 0.312000] TCP: Hash tables configured (established 512 bind 512)
  70. [ 0.320000] TCP: reno registered
  71. [ 0.324000] UDP hash table entries: 256 (order: 1, 8192 bytes)
  72. [ 0.328000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  73. [ 0.336000] NET: Registered protocol family 1
  74. [ 0.340000] PCI: CLS 0 bytes, default 16
  75. [ 0.344000] audit: initializing netlink socket (disabled)
  76. [ 0.352000] type=2000 audit(0.348:1): initialized
  77. [ 0.356000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  78. [ 0.364000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  79. [ 0.372000] msgmni has been set to 119
  80. [ 0.376000] io scheduler noop registered
  81. [ 0.380000] io scheduler deadline registered (default)
  82. [ 0.388000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
  83. [ 0.396000] console [ttyS0] enabled, bootconsole disabled
  84. [ 0.412000] bcm63xx-rng bcm63xx-rng: registered RNG driver
  85. [ 0.420000] physmap platform flash device: 08000000 at 18000000
  86. [ 0.428000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
  87. [ 0.436000] Amd/Fujitsu Extended Query Table at 0x0040
  88. [ 0.440000] Amd/Fujitsu Extended Query version 1.3.
  89. [ 0.448000] number of CFI chips: 1
  90. [ 0.452000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1541N
  91. [ 0.460000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
  92. [ 0.464000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
  93. [ 0.472000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 1ea0000
  94. [ 0.480000] bcm63xxpart: Partition 3 is nvram offset 1fe0000 and length 20000
  95. [ 0.488000] bcm63xxpart: Partition 4 is linux offset 20000 and length 1fc0000
  96. [ 0.496000] bcm63xxpart: Spare partition is offset 4a0004 and length 1b3fffc
  97. [ 0.504000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
  98. [ 0.508000] Creating 5 MTD partitions on "physmap-flash.0":
  99. [ 0.516000] 0x000000000000-0x000000020000 : "CFE"
  100. [ 0.524000] 0x000000020100-0x000000140000 : "kernel"
  101. [ 0.528000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  102. [ 0.544000] 0x000000140000-0x000001fe0000 : "rootfs"
  103. [ 0.552000] mtd: partition "rootfs" set to be root filesystem
  104. [ 0.560000] mtd: partition "rootfs_data" created automatically, ofs=4A0000, len=1B40000
  105. [ 0.568000] 0x0000004a0000-0x000001fe0000 : "rootfs_data"
  106. [ 0.576000] 0x000001fe0000-0x000002000000 : "nvram"
  107. [ 0.584000] 0x000000020000-0x000001fe0000 : "linux"
  108. [ 0.592000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
  109. [ 0.640000] b53_common: found switch: BCM63xx, rev 0
  110. [ 0.648000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
  111. [ 0.660000] TCP: cubic registered
  112. [ 0.660000] NET: Registered protocol family 17
  113. [ 0.668000] 8021q: 802.1Q VLAN Support v1.8
  114. [ 0.680000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  115. [ 0.692000] Freeing unused kernel memory: 284k freed
  116. [ 2.860000] SCSI subsystem initialized
  117. [ 3.012000] usbcore: registered new interface driver usbfs
  118. [ 3.020000] usbcore: registered new interface driver hub
  119. [ 3.024000] usbcore: registered new device driver usb
  120. [ 3.112000] Button Hotplug driver version 0.4.1
  121. [ 3.852000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  122. [ 3.864000] ehci-platform: EHCI generic platform driver
  123. [ 3.972000] ehci-platform ehci-platform: EHCI Host Controller
  124. [ 3.976000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  125. [ 3.984000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
  126. [ 4.004000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
  127. [ 4.012000] hub 1-0:1.0: USB hub found
  128. [ 4.016000] hub 1-0:1.0: 2 ports detected
  129. [ 4.132000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  130. [ 4.140000] ohci-platform ohci-platform: Generic Platform OHCI Controller
  131. [ 4.148000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
  132. [ 4.156000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
  133. [ 4.224000] hub 2-0:1.0: USB hub found
  134. [ 4.228000] hub 2-0:1.0: 1 port detected
  135. [ 4.364000] Initializing USB Mass Storage driver...
  136. [ 4.368000] usbcore: registered new interface driver usb-storage
  137. [ 4.376000] USB Mass Storage support registered.
  138. [ 4.384000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
  139. [ 10.784000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
  140. [ 10.792000] Backport generated by backports.git backports-20130617-4-ge3220f5
  141. [ 10.836000] cfg80211: Calling CRDA to update world regulatory domain
  142. [ 10.848000] cfg80211: World regulatory domain updated:
  143. [ 10.852000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  144. [ 10.864000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  145. [ 10.872000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  146. [ 10.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  147. [ 10.888000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  148. [ 10.896000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  149. [ 11.164000] NET: Registered protocol family 10
  150. [ 13.144000] wl: module license 'unspecified' taints kernel.
  151. [ 13.152000] Disabling lock debugging due to kernel taint
  152. [ 13.264000] SSB/BCMA glue driver successfully attached
  153. [ 13.620000] PPP generic driver version 2.4.2
  154. [ 14.024000] ip_tables: (C) 2000-2006 Netfilter Core Team
  155. [ 14.056000] xt_time: kernel timezone is -0000
  156. [ 14.188000] NET: Registered protocol family 24
  157. [ 14.416000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
  158. [ 18.624000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
  159. [ 20.048000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
  160. [ 20.064000] device eth0.1 entered promiscuous mode
  161. [ 20.072000] device eth0 entered promiscuous mode
  162. [ 20.080000] br-lan: port 1(eth0.1) entered forwarding state
  163. [ 20.084000] br-lan: port 1(eth0.1) entered forwarding state
  164. [ 21.044000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
  165. [ 22.088000] br-lan: port 1(eth0.1) entered forwarding state
  166. [ 27.592000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
  167. [ 27.600000] jffs2_build_filesystem(): unlocking the mtd device... done.
  168. [ 27.604000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
  169. [ 184.624000] jffs2: notice: (768) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  170. [ 214.056000] br-lan: port 1(eth0.1) entered disabled state
  171. [ 214.064000] device eth0.1 left promiscuous mode
  172. [ 214.068000] device eth0 left promiscuous mode
  173. [ 214.072000] br-lan: port 1(eth0.1) entered disabled state
  174. [ 214.204000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
  175. [ 214.240000] device eth0.1 entered promiscuous mode
  176. [ 214.244000] device eth0 entered promiscuous mode
  177. [ 214.268000] br-lan: port 1(eth0.1) entered forwarding state
  178. [ 214.272000] br-lan: port 1(eth0.1) entered forwarding state
  179. [ 215.064000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
  180. [ 216.276000] br-lan: port 1(eth0.1) entered forwarding state
RAW Paste Data