ejo60

caffieine g code customized

May 14th, 2015
369
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. ; generated by Slic3r 1.1.7 on 2015-05-10 at 08:10:00
  2.  
  3. ; Profile for high quallity print with 40% infill and 0.1 mm z step concentric fill in
  4. ;
  5. ; Materia 101
  6.  
  7. ; perimeters extrusion width = 0.35mm
  8. ; infill extrusion width = 0.98mm
  9. ; solid infill extrusion width = 0.59mm
  10. ; top infill extrusion width = 0.59mm
  11.  
  12. G21 ; set units to millimeters
  13. M107
  14. G28 ;Home all axis
  15. T0
  16. M106 S0 ;EXTRUDER FAN ON
  17. G1 Z10 F1000
  18. G1 X100 Y100 F3000
  19. M104 S210
  20. M109 S210
  21. G92 E0
  22. G90 ; use absolute coordinates
  23. G92 E0
  24. M82 ; use absolute distances for extrusion
  25. G1 F1500.000 E-2.00000
  26. G1 Z0.500 F7200.000
  27. G92 E0
  28. G1 X22.153 Y8.336 F7200.000
  29. G1 Z0.300 F7200.000
  30. G1 E2.00000 F1500.000
  31.  
  32. ... skipped all plot instructions ...
  33.  
  34. ; filament used = 6234.4mm (15.0cm3)
  35.  
  36. ; avoid_crossing_perimeters = 1
  37. ; bed_size = 140,100
  38. ; bed_temperature = 0
  39. ; bridge_acceleration = 0
  40. ; bridge_fan_speed = 50
  41. ; bridge_flow_ratio = 1.2
  42. ; brim_width = 0
  43. ; complete_objects = 0
  44. ; cooling = 1
  45. ; default_acceleration = 0
  46. ; disable_fan_first_layers = 1
  47. ; duplicate_distance = 6
  48. ; end_gcode = M104 S0\nM190 S0\nG1 Z100 F1000\nG1 X100 Y100 F3000\nM84
  49. ; external_perimeters_first = 0
  50. ; extruder_clearance_height = 20
  51. ; extruder_clearance_radius = 20
  52. ; extruder_offset = 0x0
  53. ; extrusion_axis = E
  54. ; extrusion_multiplier = 1,1,1
  55. ; fan_always_on = 1
  56. ; fan_below_layer_time = 60
  57. ; filament_diameter = 1.75
  58. ; first_layer_acceleration = 0
  59. ; first_layer_bed_temperature = 0
  60. ; first_layer_extrusion_width = 200%
  61. ; first_layer_speed = 30
  62. ; first_layer_temperature = 210
  63. ; g0 = 0
  64. ; gcode_arcs = 0
  65. ; gcode_comments = 0
  66. ; gcode_flavor = reprap
  67. ; infill_acceleration = 0
  68. ; infill_first = 0
  69. ; layer_gcode =
  70. ; max_fan_speed = 100
  71. ; min_fan_speed = 100
  72. ; min_print_speed = 20
  73. ; min_skirt_length = 0
  74. ; notes = Profile for high quallity print with 40% infill and 0.1 mm z step concentric fill in\n\nMateria 101
  75. ; nozzle_diameter = 0.35
  76. ; only_retract_when_crossing_perimeters = 1
  77. ; ooze_prevention = 0
  78. ; output_filename_format = [input_filename_base].gcode
  79. ; perimeter_acceleration = 0
  80. ; post_process =
  81. ; print_center = 70,50
  82. ; resolution = 0.05
  83. ; retract_before_travel = 0
  84. ; retract_layer_change = 1
  85. ; retract_length = 2
  86. ; retract_length_toolchange = 10
  87. ; retract_lift = 0.2
  88. ; retract_restart_extra = 0
  89. ; retract_restart_extra_toolchange = 0
  90. ; retract_speed = 25
  91. ; skirt_distance = 4
  92. ; skirt_height = 1
  93. ; skirts = 4
  94. ; slowdown_below_layer_time = 5
  95. ; spiral_vase = 0
  96. ; standby_temperature_delta = -5
  97. ; start_gcode = G28 ;Home all axis\nT0\nM106 S0 ;EXTRUDER FAN ON\nG1 Z10 F1000\nG1 X100 Y100 F3000\nM104 S[first_layer_temperature] \nM109 S[first_layer_temperature]\nG92 E0
  98. ; temperature = 205
  99. ; threads = 2
  100. ; toolchange_gcode =
  101. ; travel_speed = 120
  102. ; use_firmware_retraction = 0
  103. ; use_relative_e_distances = 0
  104. ; vibration_limit = 0
  105. ; wipe = 0
  106. ; z_offset = 0
  107. ; dont_support_bridges = 1
  108. ; extrusion_width = 0
  109. ; first_layer_height = 0.3
  110. ; infill_only_where_needed = 0
  111. ; interface_shells = 0
  112. ; layer_height = 0.1
  113. ; raft_layers = 0
  114. ; seam_position = aligned
  115. ; support_material = 0
  116. ; support_material_angle = 45
  117. ; support_material_enforce_layers = 0
  118. ; support_material_extruder = 1
  119. ; support_material_extrusion_width = 70%
  120. ; support_material_interface_extruder = 1
  121. ; support_material_interface_layers = 0
  122. ; support_material_interface_spacing = 0
  123. ; support_material_interface_speed = 100%
  124. ; support_material_pattern = pillars
  125. ; support_material_spacing = 3
  126. ; support_material_speed = 60
  127. ; support_material_threshold = 45
  128. ; bottom_solid_layers = 10
  129. ; bridge_speed = 60
  130. ; external_perimeter_speed = 45
  131. ; extra_perimeters = 0
  132. ; fill_angle = 45
  133. ; fill_density = 40%
  134. ; fill_pattern = concentric
  135. ; gap_fill_speed = 40
  136. ; infill_every_layers = 1
  137. ; infill_extruder = 1
  138. ; infill_extrusion_width = 0
  139. ; infill_speed = 70
  140. ; overhangs = 0
  141. ; perimeter_extruder = 1
  142. ; perimeter_extrusion_width = 0
  143. ; perimeter_speed = 70
  144. ; perimeters = 2
  145. ; small_perimeter_speed = 40
  146. ; solid_fill_pattern = concentric
  147. ; solid_infill_below_area = 70
  148. ; solid_infill_every_layers = 0
  149. ; solid_infill_extrusion_width = 0
  150. ; solid_infill_speed = 45
  151. ; thin_walls = 1
  152. ; top_infill_extrusion_width = 0
  153. ; top_solid_infill_speed = 40
  154. ; top_solid_layers = 10
RAW Paste Data