Guest User

Armbian boot S912

a guest
Oct 9th, 2016
789
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. TE: 231343
  2.  
  3. BL2 Built : 19:41:49, Jun 20 2016.
  4. gxl ge299011 - xiaobo.gu@droid05
  5.  
  6. set vdd cpu_a to 1120 mv
  7. set vdd cpu_b to 1050 mv
  8. set vddee to 1000 mv
  9. Board ID = 1
  10. CPU clk: 1200MHz
  11. DDR3 chl: Rank0+1 @ 912MHz - PASS
  12. DQS-corr enabled
  13. DDR scramble enabled
  14. Rank0: 1024MB(auto)-2T-13
  15. Rank1: 1024MB(auto)-2T-13
  16. DataBus test pass!
  17. AddrBus test pass!
  18. -s
  19. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  20. New fip structure!
  21. Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  22. Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00014400
  23. Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a7e00
  24. NOTICE: BL3-1: v1.0(debug):c813a61
  25. NOTICE: BL3-1: Built : 14:39:44, Jun 16 2016
  26. aml log : bl31 normal boot !
  27. [Image: gxl_v1.1.3137-2517a7a 2016-06-24 11:31:11 xing.xu@droid05]
  28. OPS=0x82
  29. fd c2 23 4a 9e 82 98 d1 8e f0 e1 16 [0.473889 Inits done]
  30. secure task start!
  31. high task start!
  32. low task start!
  33. INFO: BL3-1: Initializing runtime services
  34. WARNING: No OPTEE provided by BL2 boot loader
  35. ERROR: Error initializing runtime service opteed_fast
  36. INFO: BL3-1: Preparing for EL3 exit to normal world
  37. INFO: BL3-1: Next image address = 0x1000000
  38. INFO: BL3-1: Next image spsr = 0x3c9
  39.  
  40.  
  41. U-Boot 2015.01-g75c8ac3 (Sep 30 2016 - 10:53:55)
  42.  
  43. DRAM: 2 GiB
  44. Relocation Offset is: 76ecb000
  45. register usb cfg[0][1] = 0000000077f5f850
  46. vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
  47. vpu: clk_level = 7
  48. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  49. vpp: vpp_init
  50. boot_device_flag : 1
  51. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
  52. init bus_cycle=6, bus_timing=7, system=5.0ns
  53. reset failed
  54. get_chip_type and ret:fffffffe
  55. get_chip_type and ret:fffffffe
  56. chip detect failed and ret:fffffffe
  57. nandphy_init failed and ret=0xfffffff1
  58. MMC: aml_priv->desc_buf = 0x0000000073ecb6b0
  59. aml_priv->desc_buf = 0x0000000073ecd9d0
  60. SDIO Port B: 0, SDIO Port C: 1
  61. emmc/sd response timeout, cmd8, status=0x3ff2800
  62. emmc/sd response timeout, cmd55, status=0x3ff2800
  63. [mmc_startup] mmc refix success
  64. [mmc_init] mmc init success
  65. mmc read lba=0x14000, blocks=0x400
  66. Amlogic multi-dtb tool
  67. Multi dtb detected
  68. Multi dtb tool version: v2 .
  69. Support 2 dtbs.
  70. aml_dt soc: gxm platform: q201 variant: 2g
  71. dtb 0 soc: gxm plat: q201 vari: 1g
  72. dtb 1 soc: gxm plat: q201 vari: 2g
  73. Find match dtb: 1
  74. start dts,buffer=0000000073ed0270,dt_addr=0000000073edaa70
  75. parts: 11
  76. 00: logo 0000000002000000 1
  77. 01: recovery 0000000002000000 1
  78. 02: rsv 0000000000800000 1
  79. 03: tee 0000000000800000 1
  80. 04: crypt 0000000002000000 1
  81. 05: misc 0000000002000000 1
  82. 06: instaboot 0000000020000000 1
  83. 07: boot 0000000002000000 1
  84. 08: system 0000000080000000 1
  85. 09: cache 0000000020000000 2
  86. 10: data ffffffffffffffff 4
  87. get_dtb_struct: Get emmc dtb OK!
  88. overide_emmc_partition_table: overide cache
  89. [mmc_get_partition_table] skip partition cache.
  90. Partition table get from SPL is :
  91. name offset size flag
  92. ===================================================================================
  93. 0: bootloader 0 400000 0
  94. 1: reserved 2400000 4000000 0
  95. 2: cache 6c00000 20000000 2
  96. 3: env 27400000 800000 0
  97. 4: logo 28400000 2000000 1
  98. 5: recovery 2ac00000 2000000 1
  99. 6: rsv 2d400000 800000 1
  100. 7: tee 2e400000 800000 1
  101. 8: crypt 2f400000 2000000 1
  102. 9: misc 31c00000 2000000 1
  103. 10: instaboot 34400000 20000000 1
  104. 11: boot 54c00000 2000000 1
  105. 12: system 57400000 80000000 1
  106. 13: data d7c00000 2c5400000 4
  107. mmc read lba=0x12000, blocks=0x2
  108. mmc read lba=0x12002, blocks=0x2
  109. mmc_read_partition_tbl: mmc read partition OK!
  110. eMMC/TSD partition table have been checked OK!
  111. mmc env offset: 0x27400000
  112. In: serial
  113. Out: serial
  114. Err: serial
  115. reboot_mode=cold_boot
  116. hpd_state=1
  117. [1080p60hz] is invalid for cvbs.
  118. set hdmitx VIC = 16
  119. config HPLL = 2970
  120. HPLL: 0xc000027b
  121. config HPLL done
  122. j = 4 vid_clk_div = 1
  123. hdmitx phy setting done
  124. hdmitx: set enc for VIC: 16
  125. enc_vpu_bridge_reset[1183]
  126. rx version is 1.4 or below div=10
  127. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  128. read emmc dtb
  129. Amlogic multi-dtb tool
  130. Multi dtb detected
  131. Multi dtb tool version: v2 .
  132. Support 2 dtbs.
  133. aml_dt soc: gxm platform: q201 variant: 2g
  134. dtb 0 soc: gxm plat: q201 vari: 1g
  135. dtb 1 soc: gxm plat: q201 vari: 2g
  136. Find match dtb: 1
  137. Net: dwmac.c9410000
  138. wipe_data=successful
  139. wipe_cache=successful
  140. upgrade_step=0
  141. [OSD]load fb addr from dts
  142. [OSD]fb_addr for logo: 0x3d851000
  143. [OSD]load fb addr from dts
  144. [OSD]fb_addr for logo: 0x3d851000
  145. [CANVAS]addr=0x3d851000 width=5760, height=2160
  146.  
  147. amlkey_init() enter!
  148. [EFUSE_MSG]keynum is 4
  149. [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
  150. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  151. get_cpu_id flag_12bit=1
  152. SARADC open channel(0).
  153. SARADC channel(0) is 0x3cc, Out of range(0x0~0x50)!
  154. saradc - saradc sub-system
  155.  
  156. Usage:
  157. saradc saradc open <channel> - open a SARADC channel
  158. saradc close - close the SARADC
  159. saradc getval - get the value in current channel
  160. saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
  161.  
  162. get_cpu_id flag_12bit=1
  163. InUsbBurn
  164. noSof
  165. Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
  166. (Re)start USB...
  167. USB0: USB3.0 XHCI init start
  168. Register 3000140 NbrPorts 3
  169. Starting the controller
  170. USB XHCI 1.00
  171. scanning bus 0 for devices... 1 USB Device(s) found
  172. scanning usb for storage devices... 0 Storage Device(s) found
  173. ** Bad device usb 0 **
  174. card in
  175. [mmc_init] mmc init success
  176. Device: SDIO Port B
  177. Manufacturer ID: 3
  178. OEM: 5344
  179. Name: SL08G
  180. Tran Speed: 50000000
  181. Rd Block Len: 512
  182. SD version 3.0
  183. High Capacity: Yes
  184. Capacity: 7.4 GiB
  185. mmc clock: 40000000
  186. Bus Width: 4-bit
  187. reading s912_autoscript
  188. 929 bytes read in 4 ms (226.6 KiB/s)
  189. ## Executing script at 01020000
  190. ** Bad device usb 0 **
  191. reading uInitrd
  192. 3146047 bytes read in 179 ms (16.8 MiB/s)
  193. reading zImage
  194. 16455168 bytes read in 903 ms (17.4 MiB/s)
  195. reading dtb.img
  196. 40538 bytes read in 6 ms (6.4 MiB/s)
  197. ## Loading init Ramdisk from Legacy Image at 13000000 ...
  198. Image Name: uInitrd
  199. Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
  200. Data Size: 3145983 Bytes = 3 MiB
  201. Load Address: 00000000
  202. Entry Point: 00000000
  203. Verifying Checksum ... OK
  204. Amlogic multi-dtb tool
  205. Single dtb detected
  206. load dtb from 0x1000000 ......
  207. ## Flattened Device Tree blob at 01000000
  208. Booting using the fdt blob at 0x1000000
  209. Loading Ramdisk to 73bb8000, end 73eb80ff ... OK
  210. Loading Device Tree to 000000001fff3000, end 000000001ffffe59 ... OK
  211. signature:
  212. fdt_instaboot: no instaboot image
  213.  
  214. Starting kernel ...
  215.  
  216. uboot time: 5182715 us
  217. [ 0.000000@0] Initializing cgroup subsys cpu
  218. [ 0.000000@0] Initializing cgroup subsys cpuacct
  219. [ 0.000000@0] Linux version 3.14.29-beelinkgt1-g069e204-dirty (root@server) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #3 SMP PREEMPT Sun Oct 9 14:46:44 EEST 2016
  220. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  221. [ 0.000000@0] no prop version_code
  222. [ 0.000000@0] fdt Reserved memory table:
  223. [ 0.000000@0] linux,di: 0x000000007e200000 - 0x0000000080000000 (30 MiB)
  224. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007e200000, size 30 MiB
  225. [ 0.000000@0] linux,ion-dev: 0x000000007a200000 - 0x000000007e200000 (64 MiB)
  226. [ 0.000000@0] linux,ppmgr: 0x0000000078200000 - 0x000000007a200000 (32 MiB)
  227. [ 0.000000@0] linux,codec_mm_cma: 0x0000000066800000 - 0x0000000073800000 (208 MiB)
  228. [ 0.000000@0] linux,picdec: 0x0000000078200000 - 0x0000000078200000 (0 MiB)
  229. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  230. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000074100000 - 0x0000000078200000 (65 MiB)
  231. [ 0.000000@0] fdt Reserved memory total: 402 MiB
  232. [ 0.000000@0] cma: Reserved 8 MiB at 66000000
  233. [ 0.000000@0] psci: probing function IDs from device-tree
  234. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07406e000 s19392 r8192 d21568 u49152
  235. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
  236. [ 0.000000@0] Kernel command line: root=LABEL=ROOTFS rootwait rootflags=data=writeback rw console=ttyS0,115200n8 console=tty0 consoleblank=0 no_console_suspend hdmimode=1080p60hz m_bpp=24 fsck.repair=yes net.ifnames=0
  237. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  238. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  239. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  240. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  241. [ 0.000000@0] Memory: 1593252K/2077696K available (10140K kernel code, 1065K rwdata, 3684K rodata, 1170K init, 5861K bss, 484444K reserved)
  242. [ 0.000000@0] Virtual kernel memory layout:
  243. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  244. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042410000 ( 36 MB)
  245. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  246. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB)
  247. [ 0.000000@0] .init : 0xffffffc001e02000 - 0xffffffc001f26bc0 ( 1171 kB)
  248. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001e012b4 ( 13829 kB)
  249. [ 0.000000@0] .data : 0xffffffc001f27000 - 0xffffffc002031600 ( 1066 kB)
  250. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01e00fff]
  251. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
  252. [ 0.000000@0] arch_multi_cluster:1
  253. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  254. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  255. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  256. [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  257. [ 0.000265@0] Console: colour dummy device 80x25
  258. [ 0.000760@0] console [tty0] enabled
  259. [ 0.000781@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  260. [ 0.000806@0] pid_max: default: 32768 minimum: 301
  261. [ 0.000904@0] Security Framework initialized
  262. [ 0.000925@0] SELinux: Initializing.
  263. [ 0.001009@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  264. [ 0.001025@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  265. [ 0.003720@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
  266. [ 0.003752@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
  267. [ 0.003771@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
  268. [ 0.003788@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
  269. [ 0.007024@0] Initializing cgroup subsys debug
  270. [ 0.007046@0] Initializing cgroup subsys freezer
  271. [ 0.007093@0] ftrace: allocating 35151 entries in 138 pages
  272. [ 0.052622@0] /cpus/cpu@0: Missing clock-frequency property
  273. [ 0.052655@0] /cpus/cpu@1: Missing clock-frequency property
  274. [ 0.052671@0] /cpus/cpu@2: Missing clock-frequency property
  275. [ 0.052688@0] /cpus/cpu@3: Missing clock-frequency property
  276. [ 0.052705@0] /cpus/cpu@100: Missing clock-frequency property
  277. [ 0.052724@0] /cpus/cpu@101: Missing clock-frequency property
  278. [ 0.052743@0] /cpus/cpu@102: Missing clock-frequency property
  279. [ 0.052762@0] /cpus/cpu@103: Missing clock-frequency property
  280. [ 0.052780@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
  281. [ 0.094090@0] Meson chip version = RevA (22:A - 82:0)
  282. [ 0.112503@1] CPU1: Booted secondary processor
  283. [ 0.132487@2] CPU2: Booted secondary processor
  284. [ 0.152485@3] CPU3: Booted secondary processor
  285. [ 0.172524@4] CPU4: Booted secondary processor
  286. [ 0.192514@5] CPU5: Booted secondary processor
  287. [ 0.212531@6] CPU6: Booted secondary processor
  288. [ 0.232551@7] CPU7: Booted secondary processor
  289. [ 0.232646@0] Brought up 8 CPUs
  290. [ 0.232729@0] SMP: Total of 8 processors activated.
  291. [ 0.239396@2] sched: registering cpufreq notifiers for scale-invariant loads
  292. [ 0.239446@2] instabooting: 0
  293. [ 0.248714@2] pinctrl core: initialized pinctrl subsystem
  294. [ 0.249400@2] regulator-dummy: no parameters
  295. [ 0.250205@2] NET: Registered protocol family 16
  296. [ 0.252625@3] aml_vdac_init: module init
  297. [ 0.252830@3] register canvas platform driver
  298. [ 0.252928@3] register rdma platform driver
  299. [ 0.253924@3] vdso: 2 pages (1 code, 1 data) at base ffffffc001f30000
  300. [ 0.253984@3] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  301. [ 0.254748@3] DMA: preallocated 256 KiB pool for atomic allocations
  302. [ 0.255721@3] software IO TLB [mem 0x62400000-0x62800000] (4MB) mapped at [ffffffc062400000-ffffffc0627fffff]
  303. [ 0.255742@3] Serial: AMBA PL011 UART driver
  304. [ 0.256363@2] aml_i2c version: 20140813
  305. [ 0.256640@3] i2c-core: driver [pmu4] using legacy resume method
  306. [ 0.256838@2] codec_mm:codec_mm_module_init
  307. [ 0.257080@3] aml_watch_point_probe, in
  308. [ 0.257549@2] gxbb_mpll_clk: register mpll_clk_out0 success done
  309. [ 0.257573@2] gxbb_mpll_clk: register mpll_clk_out1 success done
  310. [ 0.257589@2] gxbb_mpll_clk: register mpll_clk_out2 success done
  311. [ 0.257774@2] clk_sys: register PLL sys_pll success done
  312. [ 0.257795@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
  313. [ 0.257807@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
  314. [ 0.257820@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
  315. [ 0.257832@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
  316. [ 0.257845@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
  317. [ 0.257857@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
  318. [ 0.257869@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
  319. [ 0.257881@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
  320. [ 0.257893@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
  321. [ 0.257928@2] gxl_clk: clock initialization complete
  322. [ 0.258125@2] clkmsr: Gxl msr_clk_reg0=ffffff800006075c,msr_clk_reg2=ffffff8000062764
  323. [ 0.260539@2] aml_iomap: amlogic iomap probe done
  324. [ 0.261225@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
  325. [ 0.262189@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
  326. [ 0.262769@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  327. [ 0.262807@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  328. [ 0.263012@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  329. [ 0.263042@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  330. [ 0.265695@3] codec_mm has 2 memory regions
  331. [ 0.265750@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  332. [ 0.265773@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  333. [ 0.265901@2] codec_mm has 2 memory regions
  334. [ 0.265929@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  335. [ 0.265952@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  336. [ 0.267949@2] vpu: driver version: v02
  337. [ 0.267995@2] vpu: load vpu_clk: 666667000Hz(7)
  338. [ 0.268111@3] vpu: vpu_probe OK
  339. [ 0.269756@2] tv_vout: tvout_probe
  340. [ 0.269784@2] tv_vout: major number 254 for disp
  341. [ 0.269795@2] vout_notify: vout_register_server
  342. [ 0.269806@2] tv_vout: register tv module server ok
  343. [ 0.269917@3] tv_vout: tvout_probe OK
  344. [ 0.270520@3] canvas_probe reg=00000000c8838000,size=400
  345. [ 0.270562@3] canvas maped reg_base =ffffff8000184000
  346. [ 0.274740@2] rdma_probe
  347. [ 0.585156@0] bio: create slab <bio-0> at 0
  348. [ 0.586323@0] SCSI subsystem initialized
  349. [ 0.586915@0] usbcore: registered new interface driver usbfs
  350. [ 0.587043@1] usbcore: registered new interface driver hub
  351. [ 0.587206@0] usbcore: registered new device driver usb
  352. [ 0.588196@0] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
  353. [ 0.588350@1] Linux video capture interface: v2.00
  354. [ 0.588588@1] pps_core: LinuxPPS API ver. 1 registered
  355. [ 0.588604@1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  356. [ 0.588692@0] PTP clock support registered
  357. [ 0.589381@1] hdmitx: system: amhdmitx_init
  358. [ 0.589401@1] hdmitx: system: Ver: 2014May6
  359. [ 0.589578@1] hdmitx: system: amhdmitx_probe
  360. [ 0.589898@2] hdmitx: system: not find match init-data
  361. [ 0.589915@2] hdmitx: system: not find match pwr-ctl
  362. [ 0.589927@2] hdmitx hpd irq = 89
  363. [ 0.590386@2] hdmitx20: Mapped PHY: 0xc0800000
  364. [ 0.590409@2] hdmitx20: Mapped PHY: 0xc1104400
  365. [ 0.590435@2] hdmitx20: Mapped PHY: 0xc8100000
  366. [ 0.590448@2] hdmitx20: Mapped PHY: 0xc8834000
  367. [ 0.590460@2] hdmitx20: Mapped PHY: 0xc883a000
  368. [ 0.590473@2] hdmitx20: Mapped PHY: 0xc883c000
  369. [ 0.590488@2] hdmitx20: Mapped PHY: 0xd0100000
  370. [ 0.590500@2] hdmitx20: Mapped PHY: 0xda83a000
  371. [ 0.590519@2] hdmitx: alread display in uboot 0x10
  372. [ 0.590548@2] avmute set to 1
  373. [ 0.590933@1] vout_serve: vout_init_module
  374. [ 0.591075@1] vout_serve: no matched vout_init mode
  375. [ 0.591186@0] vinfo: error: invalid vinfo. current vmode is not supported
  376. [ 0.591202@0] vout_serve: create vout attribute OK
  377. [ 0.591213@0] vout_serve: meson_vout_probe OK
  378. [ 0.591408@0] logo: logo_init
  379. [ 0.591742@0] Advanced Linux Sound Architecture Driver Initialized.
  380. [ 0.592406@0] Bluetooth: Core ver 2.18
  381. [ 0.592538@1] NET: Registered protocol family 31
  382. [ 0.592552@1] Bluetooth: HCI device and connection manager initialized
  383. [ 0.592574@1] Bluetooth: HCI socket layer initialized
  384. [ 0.592589@1] Bluetooth: L2CAP socket layer initialized
  385. [ 0.592624@1] Bluetooth: SCO socket layer initialized
  386. [ 0.592641@1] NetLabel: Initializing
  387. [ 0.592651@1] NetLabel: domain hash size = 128
  388. [ 0.592661@1] NetLabel: protocols = UNLABELED CIPSOv4
  389. [ 0.592714@1] NetLabel: unlabeled traffic allowed by default
  390. [ 0.594689@0] Switched to clocksource arch_sys_counter
  391. [ 0.597636@0] hdmitx: system: irq 80000002
  392. [ 0.635631@0] [amlatvdemod..]aml_atvdemod_init.
  393. [ 0.635746@0] NET: Registered protocol family 2
  394. [ 0.636308@0] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  395. [ 0.636443@0] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  396. [ 0.636674@0] TCP: Hash tables configured (established 16384 bind 16384)
  397. [ 0.636753@0] TCP: reno registered
  398. [ 0.636771@0] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  399. [ 0.636824@0] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  400. [ 0.637071@0] NET: Registered protocol family 1
  401. [ 0.637345@0] RPC: Registered named UNIX socket transport module.
  402. [ 0.637364@0] RPC: Registered udp transport module.
  403. [ 0.637375@0] RPC: Registered tcp transport module.
  404. [ 0.637386@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
  405. [ 0.637609@0] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
  406. [ 0.637625@0] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
  407. [ 0.637685@0] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
  408. [ 0.637753@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
  409. [ 0.637771@0] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
  410. [ 0.637786@0] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
  411. [ 0.637803@0] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
  412. [ 0.637816@0] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
  413. [ 0.638134@0] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
  414. [ 0.638182@0] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
  415. [ 0.638206@0] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
  416. [ 0.638566@0] Unpacking initramfs...
  417. [ 0.757710@0] Freeing initrd memory: 3072K (ffffffc073bb8000 - ffffffc073eb8000)
  418. [ 0.761910@0] futex hash table entries: 2048 (order: 5, 131072 bytes)
  419. [ 0.762025@0] audit: initializing netlink subsys (disabled)
  420. [ 0.762081@0] audit: type=2000 audit(0.730:1): initialized
  421. [ 0.762979@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
  422. [ 0.770586@0] VFS: Disk quotas dquot_6.5.2
  423. [ 0.770872@0] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  424. [ 0.776113@0] NFS: Registering the id_resolver key type
  425. [ 0.776163@0] Key type id_resolver registered
  426. [ 0.776175@0] Key type id_legacy registered
  427. [ 0.776207@0] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  428. [ 0.777033@1] fuse init (API version 7.22)
  429. [ 0.777699@0] msgmni has been set to 3549
  430. [ 0.779261@0] NET: Registered protocol family 38
  431. [ 0.779658@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  432. [ 0.779689@0] io scheduler noop registered
  433. [ 0.779699@0] io scheduler deadline registered
  434. [ 0.779907@0] io scheduler cfq registered (default)
  435. [ 0.831510@1] meson-rng c8834000.rng: hwrng registered
  436. [ 0.836014@1] loop: module loaded
  437. [ 0.836659@1] zram: Created 1 device(s) ...
  438. [ 0.837700@2] mtdoops: mtd device (mtddev=name/number) must be supplied
  439. [ 0.838522@1] tun: Universal TUN/TAP device driver, 1.6
  440. [ 0.838546@1] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  441. [ 0.924859@0] hdmitx: plugin
  442. [ 0.968408@3] libphy: stmmac: probed
  443. [ 0.968437@3] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
  444. [ 0.968451@3] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
  445. [ 0.968951@3] PPP generic driver version 2.4.2
  446. [ 0.969184@3] PPP BSD Compression module registered
  447. [ 0.969200@3] PPP Deflate Compression module registered
  448. [ 0.969234@3] PPP MPPE Compression module registered
  449. [ 0.969246@3] NET: Registered protocol family 24
  450. [ 0.969405@3] usbcore: registered new interface driver asix
  451. [ 0.969565@3] usbcore: registered new interface driver ax88179_178a
  452. [ 0.969684@3] usbcore: registered new interface driver cdc_ether
  453. [ 0.969797@3] usbcore: registered new interface driver net1080
  454. [ 0.969911@3] usbcore: registered new interface driver cdc_subset
  455. [ 0.970022@3] usbcore: registered new interface driver zaurus
  456. [ 0.970163@3] usbcore: registered new interface driver cdc_ncm
  457. [ 0.970484@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  458. [ 0.970503@3] ehci-h20ahb: H20AHB-EHCI Host Controller driver
  459. [ 0.970748@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  460. [ 0.971126@3] usbcore: registered new interface driver cdc_acm
  461. [ 0.971143@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  462. [ 0.971277@3] usbcore: registered new interface driver usb-storage
  463. [ 0.971516@3] usbcore: registered new interface driver usbserial
  464. [ 0.972210@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80001f6000
  465. [ 0.972461@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  466. [ 0.972495@3] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80001f8080
  467. [ 0.973170@3] mousedev: PS/2 mouse device common for all mice
  468. [ 0.973765@3] usbcore: registered new interface driver xpad
  469. [ 0.973985@3] i2c /dev entries driver
  470. [ 0.974320@3] usbcore: registered new interface driver uvcvideo
  471. [ 0.974336@3] USB Video Class driver (1.1.1)
  472. [ 0.975275@3] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
  473. [ 0.975412@3] Bluetooth: HCI UART driver ver 2.2
  474. [ 0.975429@3] Bluetooth: HCI H4 protocol initialized
  475. [ 0.975517@3] cpufreq-hotplug: cpufreq_gov_dbs_init: assumes CONFIG_NO_HZ
  476. [ 0.975677@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
  477. [ 0.977887@3] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
  478. [ 0.978046@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
  479. [ 0.979015@3] @@@@@@@@@@_____2______in dia_init()
  480. [ 0.979036@3] ATVR driver - init called!
  481. [ 0.979264@3] usbcore: registered new interface driver usbhid
  482. [ 0.979279@3] usbhid: USB HID core driver
  483. [ 0.979628@3] ashmem: initialized
  484. [ 0.979788@3] logger: created 256K log 'log_main'
  485. [ 0.979920@3] logger: created 256K log 'log_events'
  486. [ 0.980053@3] logger: created 256K log 'log_radio'
  487. [ 0.980186@3] logger: created 256K log 'log_system'
  488. [ 0.981192@3] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80001fa4c0
  489. [ 0.981233@3] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  490. [ 0.981258@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
  491. [ 1.059959@0] hdmitx: edid: check sum valid
  492. [ 1.059961@0] hdmitx: edid: check sum valid
  493. [ 1.059965@0] hdmitx: edid: blk0 raw data
  494. [ 1.059998@0] 00ffffffffffff004dd902300101010101150103804728780a0dc9a057479827
  495. [ 1.059998@0] 12484c21080081800101010101010101010101010101023a801871382d40582c
  496. [ 1.059998@0] 4500c48e2100001e011d007251d01e206e285500c48e2100001e000000fc0053
  497. [ 1.059998@0] 4f4e592054560a2020202020000000fd00303e0e460f000a202020202020016d
  498. [ 1.059998@0]
  499. [ 1.059998@0]
  500. [ 1.060000@0] hdmitx: edid: blk1 raw data
  501. [ 1.060030@0] 02032ff0531f101405130420223c3e1216030711150206012609070715075083
  502. [ 1.060030@0] 01000068030c003000b82d0fe200fb023a80d072382d40102c4580c48e210000
  503. [ 1.060030@0] 1e011d00bc52d01e20b8285540c48e2100001e011d8018711c1620582c2500c4
  504. [ 1.060030@0] 8e2100009e011d80d0721c1620102c2580c48e2100009e00000000000000009c
  505. [ 1.060030@0]
  506. [ 1.060030@0]
  507. [ 1.060033@0] EDID Parser:
  508. [ 1.060080@0] hdmitx: edid: find IEEEOUT
  509. [ 1.060084@0] vinfo: error: invalid vinfo. current vmode is not supported
  510. [ 1.060086@0] hdmitx: update RX hdr info 0
  511. [ 1.062105@0] hdmitx: ddc rd8b error 0x3a 0x00 0x00
  512. [ 1.064145@0] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
  513. [ 1.064149@0] vinfo: error: invalid vinfo. current vmode is not supported
  514. [ 1.064151@0] hdmitx: video: get current mode: invalid
  515. [ 1.064152@0] hdmitx: update rx hdr info 0
  516. [ 1.064171@0] hdmitx: edid: not find mapped vic
  517. [ 1.064199@0] hdmitx: system: already init VIC = 0 Now VIC = 0
  518. [ 1.064201@0] hdmitx: system: packet: can't get vendor data
  519. [ 1.064203@0] hdmtix: set audio
  520. [ 1.064211@0] hdmitx tx_aud_src = 0
  521. [ 1.064221@0] hdmitx: system: irq 80000001
  522. [ 1.064254@0] hdmitx aud_n_para = 6144
  523. [ 1.064271@0] hdmitx set channel status
  524. [ 1.064328@0] hdmtix: set audio
  525. [ 1.064336@0] hdmitx tx_aud_src = 0
  526. [ 1.064359@0] hdmitx aud_n_para = 6144
  527. [ 1.064376@0] hdmitx set channel status
  528. [ 1.064439@0] Start = 0x10000100 End = 0x100001ff
  529. [ 1.064446@0] [0x10000103]: 0x00000008
  530. [ 1.064449@0] [0x10000104]: 0x00000001
  531. [ 1.064599@0] [0x10000170]: 0x00000010
  532. [ 1.064622@0] [0x10000180]: 0x000000ff
  533. [ 1.064625@0] [0x10000181]: 0x000000ff
  534. [ 1.064627@0] [0x10000182]: 0x00000003
  535. [ 1.064630@0] [0x10000183]: 0x00000007
  536. [ 1.064633@0] [0x10000184]: 0x0000003f
  537. [ 1.064635@0] [0x10000185]: 0x00000002
  538. [ 1.064639@0] [0x10000187]: 0x000000ff
  539. [ 1.064642@0] [0x10000188]: 0x00000003
  540. [ 2.745622@3] console [ttyS0] enabled
  541. [ 2.749609@3] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001fc4c0
  542. [ 2.756341@3] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  543. [ 2.766082@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
  544. [ 2.775569@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
  545. [ 2.783036@3] hdmitx: system: hdmitx_hdcp_init
  546. [ 2.787355@3] ESM HLD: Initializing...
  547. [ 2.790892@3] ESM HLD: Registering device range 'esm'...
  548. [ 2.796167@3] ESM HLD: Device range 'esm' has been registered.
  549. [ 2.801931@3] ESM HLD: Creating class /sys/class/elliptic...
  550. [ 2.807641@0] ESM HLD: The class /sys/class/elliptic has been created.
  551. [ 2.814006@0] ESM HLD: Creating device 'esm'...
  552. [ 2.818622@3] ESM HLD: Device 'esm' has been created.
  553. [ 2.823494@3] ESM HLD: Done initializing the HLD driver.
  554. INFO: HDCP22 key read fail!
  555. INFO: p1d 0
  556. INFO: pd1 0
  557. [ 2.844706@3] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
  558. [ 2.846108@3] secmon has 1 memory regions
  559. [ 2.849420@3] secmon: share in base: 0xffffff8000412000, share out base: 0xffffff8000414000
  560. [ 2.857707@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
  561. [ 2.864652@3] secmon: probe done
  562. [ 2.868159@0] storage: storage in base: 0xffffff8001600000
  563. [ 2.873278@0] storage: storage out base: 0xffffff8001680000
  564. [ 2.878808@0] storage: storage block base: 0xffffff8001700000
  565. [ 2.884489@0] storage: probe done!
  566. [ 2.888375@3] aml_sd_emmc_probe: line 3556
  567. [ 2.891909@3] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
  568. [ 2.901918@3] aml_sd_emmc_reg_init 1144
  569. [ 2.905189@3] get property: ocr_avail, value:0x00200080
  570. [ 2.911573@3] get property: f_min, value:400000
  571. [ 2.917702@3] get property: f_max, value:100000000
  572. [ 2.924079@3] get property: max_req_size, value:0x00020000
  573. [ 2.930553@3] get property: irq_in, value:3
  574. [ 2.936253@3] get property: irq_out, value:5
  575. [ 2.941948@3] get property: gpio_cd, str:
  576. [ 2.947373@3] get property: pinname, str:sd
  577. [ 2.952974@3] get property: jtag_pin, str:
  578. [ 2.958414@3] get property: card_type, value:5
  579. [ 2.964100@3] get property: gpio_dat3, str:
  580. [ 2.969550@3] sd:pdata->caps = 7
  581. [ 2.972724@3] sd:pdata->caps2 = 0
  582. [ 3.014864@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  583. [ 3.014907@4] [aml_is_card_insert] card IN
  584. [ 3.019144@0] aml_sd_emmc_probe: line 3556
  585. [ 3.023517@0] aml_sd_emmc_reg_init 1144
  586. [ 3.027073@0] get property: ocr_avail, value:0x00200080
  587. [ 3.033436@0] get property: f_min, value:300000
  588. [ 3.039567@0] get property: f_max, value:100000000
  589. [ 3.045948@0] get property: max_req_size, value:0x00020000
  590. [ 3.052414@0] get property: pinname, str:emmc
  591. [ 3.058197@0] get property: card_type, value:1
  592. [ 3.063891@0] get property: gpio_dat3, str:
  593. [ 3.069340@0] get property: hw_reset, str:
  594. [ 3.074782@0] emmc:pdata->caps = c0000d47
  595. [ 3.078720@0] emmc:pdata->caps2 = 18060
  596. [ 3.082521@0] storage 1, boot 1
  597. [ 3.085621@0] get_storage_dev return 1
  598. [ 3.116171@4] normal card in
  599. [ 3.124692@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  600. [ 3.124910@3] aml_sd_emmc_probe: line 3556
  601. [ 3.129312@3] aml_sd_emmc_reg_init 1144
  602. [ 3.132791@3] get property: ocr_avail, value:0x00200080
  603. [ 3.139218@3] get property: f_min, value:400000
  604. [ 3.145333@3] get property: f_max, value:200000000
  605. [ 3.151710@3] get property: max_req_size, value:0x00020000
  606. [ 3.158186@3] get property: pinname, str:sdio
  607. [ 3.163959@3] get property: card_type, value:3
  608. [ 3.169688@3] sdio:pdata->caps = 7810f
  609. [ 3.173358@3] sdio:pdata->caps2 = 0
  610. [ 3.214694@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  611. [ 3.215205@1] ion_dev has 1 memory regions
  612. [ 3.234945@1] fb: osd_init_module
  613. [ 3.235089@1] fb: viu vsync irq: 35
  614. [ 3.236091@1] fb: failed to init reserved memory
  615. [ 3.240674@1] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
  616. [ 3.246803@1] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
  617. [ 3.253602@1] tv_vout: TV mode 1080p60hz selected.
  618. [ 3.258352@1]
  619. [ 3.258352@1] vdac_enable: on:0,module_sel:8
  620. [ 3.264209@1]
  621. [ 3.264209@1] vdac_enable: on:0,module_sel:8
  622. [ 3.270078@1] tv_vout: new mode =1080p60hz set ok
  623. [ 3.274759@1] vout_serve: vinfo mode is: 1080p60hz
  624. [ 3.279641@1] osd_rdma: osd_rdma_init: rdma_table p=0x66046000,op=0x66046000 , v=0xffffff8000587000
  625. [ 3.288457@1] osd_rdma: osd rdma request irq as second interrput function!
  626. [ 3.295276@1] fb: osd_probe vinfo:ffffffc001fc58d8
  627. [ 3.300010@1] fb: init fbdev bpp is:32
  628. [ 3.344686@2] fb: osd probe OK
  629. [ 3.344931@1] ge2d: ge2d_init_module
  630. [ 3.345658@1] ge2d: ge2d_dev major:243
  631. [ 3.349717@2] ge2d: ge2d clock is 400 MHZ
  632. [ 3.353330@2] ge2d: ge2d: pdev=ffffffc063792200, irq=182, rstc=0xffffffc063749ec0, clk=ffffffc06375ef00
  633. [ 3.362689@2] ge2d: mapped phy: 0xd0160000
  634. [ 3.366705@2] ge2d: ge2d start monitor
  635. [ 3.370468@0] ge2d: ge2d workqueue monitor start
  636. [ 3.370691@1] sysled: module init
  637. [ 3.370806@1] sysled: led_gpio = 154
  638. [ 3.370807@1] sysled: active_low = 0
  639. [ 3.370958@2] sysled: module probed ok
  640. [ 3.371337@2] pwmled: module init
  641. [ 3.371418@2] codec:Amlogic A/V streaming port init
  642. [ 3.372669@2] codec:get gate demux control ok ffffffc0636f5cc0
  643. [ 3.372674@2] codec:get gate parser_top control ok ffffffc06210b200
  644. [ 3.372678@2] codec:get gate vpu_intr control ok ffffffc06210bb40
  645. [ 3.372684@2] codec:get gate vdec control ok ffffffc06210b240
  646. [ 3.373263@2] codec:[tsync_pcr_init]init success.
  647. [ 3.373265@2] codec:amvideocap_init_module
  648. [ 3.373378@2] codec:amvideocap_probe,amvideocap
  649. [ 3.373381@2] codec:use cma buf.
  650. [ 3.373383@2] codec:amvideocap_dev_register
  651. [ 3.374918@2] amvenc_avc_probe -- reserved memory config fail.
  652. [ 3.374921@2] amvenc_avc - cma memory pool size: 40 MB
  653. [ 3.374939@2] encode_wq_init.
  654. [ 3.374943@2] encode start monitor.
  655. [ 3.374993@3] encode workqueue monitor start.
  656. [ 3.375381@2] jpegenc module init
  657. [ 3.375667@2] codec:picdec_driver_probe called.
  658. [ 3.375671@2] picdec has 1 memory regions
  659. [ 3.375690@2] codec:picdec_driver_probe done.
  660. [ 3.376562@2] codec:create_ge2d_work_queue video task ok
  661. [ 3.376906@2] codec:used fix clk for vdec clk source!
  662. [ 3.376913@2] codec:register clk_set_setting cpu[34]
  663. [ 3.377217@2] vpu_init
  664. [ 3.377389@2] vpu_probe
  665. [ 3.377392@2] HevcEnc reserved memory config fail.
  666. [ 3.377396@2] HevcEnc - cma memory pool size: 64 MB
  667. [ 3.377398@2] HevcEnc - wave420l_irq: 219
  668. [ 3.377437@2] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000590000
  669. [ 3.377711@2] success to probe vpu device with video memory from cma
  670. [ 3.377857@2] DI: di_module_init ok.
  671. [ 3.377860@2] DI: di_module_init: major 236
  672. [ 3.378041@2] DI: di_probe
  673. [ 3.378141@2] deinterlace has 1 memory regions
  674. [ 3.378171@2] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
  675. [ 3.378191@2] di_irq:78,timerc_irq:38
  676. [ 3.555419@2] rdma_register, rdma_table_addr ffffff8000589000 rdma_table_addr_phy 66048000 reg_buf ffffffc061238000
  677. [ 3.565698@2] rdma_register success, handle 1 table_size 8192
  678. [ 3.571368@2] DI: di_probe allocate rdma channel 1.
  679. [ 3.576205@2] DI: DI hw version 2.
  680. [ 3.579570@2] 0x000000db:Y=db,U=0,V=0
  681. [ 3.581881@3] emmc: BKOPS_EN bit is not set
  682. [ 3.587355@2] 0x000000dc:Y=dc,U=0,V=0
  683. [ 3.590904@3] emmc: trying cali 0-th time(s)
  684. [ 3.594480@3] emmc: delay[0]= 4600 padding= 2, bidx=4
  685. [ 3.594482@3] emmc: delay[1]= 4600 padding= 2, bidx=4
  686. [ 3.594484@3] emmc: delay[2]= 4400 padding= 3, bidx=4
  687. [ 3.594486@3] emmc: delay[3]= 4800 padding= 1, bidx=4
  688. [ 3.594488@3] emmc: delay[4]= 4800 padding= 1, bidx=4
  689. [ 3.594490@3] emmc: delay[5]= 4800 padding= 1, bidx=4
  690. [ 3.594494@3] emmc: delay[7]= 4800 padding= 1, bidx=4
  691. [ 3.594496@3] emmc: calibretion result @ 0: max(4800), min(4400)
  692. [ 3.594499@3] emmc: line_delay =0x1000211, max_cal_result =4800
  693. [ 3.594500@3] emmc: base_index_max 4, base_index_min 4
  694. [ 3.594505@3] emmc: clk 100000000 SDR mode tuning start
  695. [ 3.595151@3] emmc: rx_tuning_result[0] = 10
  696. [ 3.595599@3] emmc: rx_tuning_result[1] = 10
  697. [ 3.596046@3] emmc: rx_tuning_result[2] = 10
  698. [ 3.596493@3] emmc: rx_tuning_result[3] = 10
  699. [ 3.596942@3] emmc: rx_tuning_result[4] = 10
  700. [ 3.597389@3] emmc: rx_tuning_result[5] = 10
  701. [ 3.597834@3] emmc: rx_tuning_result[6] = 10
  702. [ 3.598282@3] emmc: rx_tuning_result[7] = 10
  703. [ 3.598727@3] emmc: rx_tuning_result[8] = 10
  704. [ 3.598771@3] emmc: best_win_start =0, best_win_size =9
  705. [ 3.598774@3] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
  706. [ 3.598777@3] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
  707. [ 3.599093@3] emmc: new HS200 MMC card at address 0001
  708. [ 3.599551@1] emmc: clock 100000000, 8-bit-bus-width
  709. [ 3.599551@1]
  710. [ 3.599551@1] mmcblk0: emmc:0001 NCard 14.4 GiB
  711. [ 3.599667@1] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
  712. [ 3.599777@1] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
  713. [ 3.599887@1] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
  714. [ 3.600485@3] mmcblk0: unknown partition table
  715. [ 3.601788@3] mmcblk0boot1: unknown partition table
  716. [ 3.602583@3] mmcblk0boot0: unknown partition table
  717. [ 3.602835@1] clear_emmc_wait_flag
  718. [ 3.720035@1] sd: new high speed SDHC card at address aaaa
  719. [ 3.720430@3] sd: clock 50000000, 4-bit-bus-width
  720. [ 3.720430@3]
  721. [ 3.720430@3] mmcblk1: sd:aaaa SL08G 7.40 GiB
  722. [ 3.721494@1] mmcblk1: p1 p2
  723. [ 3.785739@2] 0x000000dd:Y=dd,U=0,V=0
  724. [ 3.789321@2] 0x000000de:Y=de,U=0,V=0
  725. [ 3.792943@2] 0x000000df:Y=df,U=0,V=0
  726. [ 3.796571@2] 0x000000e0:Y=e0,U=0,V=0
  727. [ 3.800188@2] 0x000000e1:Y=e1,U=0,V=0
  728. [ 3.803811@2] 0x000000e2:Y=e2,U=0,V=0
  729. [ 3.807462@2] 0x000000e3:Y=e3,U=0,V=0
  730. [ 3.811056@2] 0x000000f0:Y=f0,U=0,V=0
  731. [ 3.814687@2] 0x000000f1:Y=f1,U=0,V=0
  732. [ 3.818301@2] 0x000000f2:Y=f2,U=0,V=0
  733. [ 3.821923@2] 0x000000f3:Y=f3,U=0,V=0
  734. [ 3.825554@2] 0x000000f4:Y=f4,U=0,V=0
  735. [ 3.829168@2] 0x000000f5:Y=f5,U=0,V=0
  736. [ 3.832791@2] 0x000000f6:Y=f6,U=0,V=0
  737. [ 3.836427@2] 0x000000f7:Y=f7,U=0,V=0
  738. [ 3.840036@2] 0x000000f8:Y=f8,U=0,V=0
  739. [ 3.843658@2] 0x000000f9:Y=f9,U=0,V=0
  740. [ 3.847286@2] 0x000000fa:Y=fa,U=0,V=0
  741. [ 3.850903@2] 0x000000fb:Y=fb,U=0,V=0
  742. [ 3.854526@2] 0x000000fc:Y=fc,U=0,V=0
  743. [ 3.858281@2] DI: di_probe here.
  744. [ 3.861695@2] efusekeynum: 4
  745. [ 3.864193@2] efusekeyname: mac offset: 0 size: 6
  746. [ 3.870609@2] efusekeyname: mac_bt offset: 6 size: 6
  747. [ 3.876974@2] efusekeyname: mac_wifi offset: 12 size: 6
  748. [ 3.883337@2] efusekeyname: usid offset: 18 size: 16
  749. [ 3.890007@0] efuse efuse.10: probe OK!
  750. [ 3.893884@1] key unify config unifykey-num is 14
  751. [ 3.898227@1] key unify fact unifykey-num is 14
  752. [ 3.902657@1] aml_unifykeys_probe:1267=============unifykey_devno:ea00000
  753. [ 3.909636@0] 6unifykey: device unifykeys created ok
  754. [ 3.914509@1] 6aml_unifykeys_init done!
  755. [ 3.918287@1] PPMGRDRV: warn: ppmgr module init func called
  756. [ 3.923928@1] PPMGRDRV: err: ppmgr_driver_probe called
  757. [ 3.928882@1] ppmgr has 1 memory regions
  758. [ 3.932780@1] PPMGRDRV: info: ppmgr_dev major:233
  759. [ 3.937701@0] PPMGRDRV: info: ppmgr_probe done
  760. [ 3.942236@0] amlogic rfkill init
  761. [ 3.945252@0] enter bt_probe of_node
  762. [ 3.948638@0] not get gpio_en
  763. [ 3.951558@0] power on valid level is high
  764. [ 3.955797@1] Bluetooth: BlueSleep Mode Driver Ver 1.2
  765. [ 3.961156@1] ionvideo-000: V4L2 device registered as video13
  766. [ 3.966409@1] ionvid: info: Video Technology Magazine Ion Video
  767. [ 3.972257@1] ionvid: info: Capture Board ver 1.0 successfully loaded
  768. [ 3.978689@1] audio_dsp: [dsp]register dsp to char divece(257)
  769. [ 3.985146@0] amaudio: amaudio: driver amaudio succuess!
  770. [ 3.989984@0] amlvid:err: amlvideo_init called
  771. [ 3.993907@0] amlvid:err: amlvideo_create_instance called
  772. [ 3.999444@0] amlvid:err: v4l2_dev.name=:amlvideo-000
  773. [ 4.004572@1] amlvideo-000: V4L2 device registered as video10
  774. [ 4.010524@0] vdin_drv_init: major 232
  775. [ 4.014162@0] vdin_drv_init: vdin driver init done
  776. [ 4.018611@0] tvafe_drv_init: major 231
  777. [ 4.022702@1] tvafe: tvafe_init.
  778. [ 4.025910@0] [RX]-hdmirx: hdmirx_init.
  779. [ 4.029357@0] ESM HLD: Initializing...
  780. [ 4.033064@0] ESM HLD: Registering device range 'esm_rx'...
  781. [ 4.038601@0] ESM HLD: Device range 'esm_rx' has been registered.
  782. [ 4.044621@0] ESM HLD: Creating class /sys/class/elliptic_rx...
  783. [ 4.050641@1] ESM HLD: The class /sys/class/elliptic_rx has been created.
  784. [ 4.057233@1] ESM HLD: Creating device 'esm_rx'...
  785. [ 4.062097@0] ESM HLD: Device 'esm_rx' has been created.
  786. [ 4.067243@0] ESM HLD: Done initializing the HLD driver.
  787. [ 4.072481@0] [viuin..]viuin_init_module viuin module init
  788. [ 4.078406@1] [viuin..]viuin_probe probe ok.
  789. [ 4.082219@0] module init
  790. [ 4.084893@0]
  791. [ 4.084893@0] VECM probe start
  792. [ 4.089760@1] aml_vecm_probe: ok
  793. [ 4.093294@1] saradc c1108680.saradc: initialized by BL30
  794. [ 4.098062@1] saradc c1108680.saradc: calibration start:
  795. [ 4.103313@1] saradc c1108680.saradc: nominal=0, value=5
  796. [ 4.108581@1] saradc c1108680.saradc: nominal=256, value=251
  797. [ 4.114181@1] saradc c1108680.saradc: nominal=512, value=499
  798. [ 4.119817@1] saradc c1108680.saradc: nominal=768, value=748
  799. [ 4.125399@1] saradc c1108680.saradc: nominal=1023, value=996
  800. [ 4.131045@1] saradc c1108680.saradc: calibration end: coef=4219
  801. [ 4.137247@0] remote: Driver init
  802. [ 4.140372@0] remote: platform_data g_remote_ao_offset=580
  803. [ 4.145742@0] remote: platform_data irq =228
  804. [ 4.149956@0] remote: set drvdata completed
  805. [ 4.154167@0] remote: device_create_file completed
  806. [ 4.159361@0] input: aml_keypad as /devices/meson-remote.12/input/input0
  807. [ 4.166015@0] remote: input_register_device completed
  808. [ 4.170933@0] remote: set_remote_mode[74]
  809. [ 4.174894@0] remote: remote config major:228
  810. [ 4.179474@0] remote: physical address:0x6116a000
  811. [ 4.184515@0] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
  812. [ 4.190229@0] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
  813. [ 4.196984@0] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
  814. [ 4.202656@0] gpio-key gpio_keypad.48: start setup_timer
  815. [ 4.207906@0] gpio-key gpio_keypad.48: power key(116) registed.
  816. [ 4.213996@0] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
  817. [ 4.220567@1] gpio-key gpio_keypad.48: gpio keypad register input device completed.
  818. [ 4.228038@1] input input1: gpio keypad major:227
  819. [ 4.233887@0] Sensor: lsm303d_init
  820. [ 4.236281@0] Sensor: stk8313_init
  821. [ 4.239456@0] Sensor: stk831x_init
  822. [ 4.242812@1] Sensor: mxc622x_acc_init
  823. [ 4.246567@0] Sensor: mxc6255xc_acc_init
  824. [ 4.250480@1] Sensor: l3gd20_gyr_init
  825. [ 4.254940@0] aml dvb init
  826. [ 4.257077@1] Amlogic Demod DVB-T/C DebugIF Init
  827. [ 4.261383@0] Amlogic Demod DVB-T/C DebugIF Init ok----------------
  828. [ 4.268294@0] jtag: module init
  829. [ 4.270654@1] jtag: set state 4294967295
  830. efuse_pw_en: 0x3
  831. WARNING! efuse bits is disabled
  832. Enable A53 JTAG cluster 1 to EE
  833. [ 4.287510@0] jtag: module probed ok
  834. [ 4.287893@0] cpuinfo: probe done
  835. [ 4.289033@0] defendkey c8834500.defendkey: defendkey_devno:df00000
  836. [ 4.295219@0] defendkey c8834500.defendkey: defendkey: device defendkey created ok
  837. [ 4.302634@0] defendkey: driver init
  838. [ 4.306057@0] input input1: key 116 up
  839. [ 4.310461@0] input: cec_input as /devices/virtual/input/input2
  840. [ 4.315833@1] cectx aocec: aml_cec_probe(): no hdmirx reg resource
  841. [ 4.321684@1] cectx aocec: aml_cec_probe(): no hhi reg resource
  842. [ 4.327645@1] cectx aocec: aml_cec_probe(): can't find hdmirx
  843. [ 4.334371@1] cec: wake up flag:0
  844. [ 4.337147@0] aml_aes_dma c883e000.aml_aes: Aml AES_dma
  845. [ 4.342255@0] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
  846. [ 4.347864@1] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
  847. [ 4.354138@1] usbcore: registered new interface driver snd-usb-audio
  848. [ 4.361354@1] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
  849. [ 4.574925@0] aml_snd_card: headphone detection disable=1
  850. [ 4.574963@0] aml_snd_card: no spk event delay time set
  851. [ 4.580526@0] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
  852. [ 4.587991@0] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
  853. [ 4.594728@0] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
  854. [ 4.601616@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
  855. [ 4.609221@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  856. [ 4.617997@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
  857. [ 4.625585@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  858. WARNING: Unimplemented Sip Call: 0x82000035
  859. WARNING: Unimplemented Sip Call: 0x82000035
  860. [ 4.642137@0] aml_snd_card: audio use jtag pinmux as i2s output, read val =ffffffff
  861. WARNING: Unimplemented Sip Call: 0x82000036
  862. [ 4.654260@3] GACT probability NOT on
  863. [ 4.657245@3] Mirror/redirect action on
  864. [ 4.661026@3] u32 classifier
  865. [ 4.663869@3] Actions configured
  866. [ 4.667415@3] Netfilter messages via NETLINK v0.30.
  867. [ 4.672287@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  868. [ 4.678962@0] ctnetlink v0.93: registering with nfnetlink.
  869. [ 4.684380@0] xt_time: kernel timezone is -0000
  870. [ 4.688456@0] ipip: IPv4 over IPv4 tunneling driver
  871. [ 4.693936@0] ip_tables: (C) 2000-2006 Netfilter Core Team
  872. [ 4.698798@0] arp_tables: (C) 2002 David S. Miller
  873. [ 4.703438@0] TCP: cubic registered
  874. [ 4.706870@0] Initializing XFRM netlink socket
  875. [ 4.712082@3] NET: Registered protocol family 10
  876. [ 4.716871@0] mip6: Mobile IPv6
  877. [ 4.718916@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
  878. [ 4.724666@0] sit: IPv6 over IPv4 tunneling driver
  879. [ 4.730526@0] NET: Registered protocol family 17
  880. [ 4.733769@0] NET: Registered protocol family 15
  881. [ 4.738507@0] Bridge firewalling registered
  882. [ 4.742536@0] Bluetooth: RFCOMM TTY layer initialized
  883. [ 4.747487@0] Bluetooth: RFCOMM socket layer initialized
  884. [ 4.752734@0] Bluetooth: RFCOMM ver 1.11
  885. [ 4.756674@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  886. [ 4.762023@0] Bluetooth: BNEP filters: protocol multicast
  887. [ 4.767415@0] Bluetooth: BNEP socket layer initialized
  888. [ 4.772459@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  889. [ 4.778513@0] Bluetooth: HIDP socket layer initialized
  890. [ 4.783639@0] l2tp_core: L2TP core driver, V2.0
  891. [ 4.788110@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  892. [ 4.792986@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
  893. [ 4.798713@0] l2tp_netlink: L2TP netlink interface
  894. [ 4.803455@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
  895. [ 4.809488@0] l2tp_debugfs: L2TP debugfs support
  896. [ 4.814031@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
  897. [ 4.820660@0] NET: Registered protocol family 35
  898. [ 4.825227@0] Key type dns_resolver registered
  899. [ 4.830402@0] Registering SWP/SWPB emulation handler
  900. [ 4.835224@0] regulator-dummy: disabling
  901. [ 4.838759@0] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:10 UTC (1420070410)
  902. [ 4.848746@0] gxbb_pm: enter meson_pm_probe!
  903. [ 4.850893@0] gxbb_pm: meson_pm_probe done
  904. [ 4.855806@0] cpucore_cooling_register, max_cpu_core_num:4
  905. [ 4.860520@0] cpucore_cooling_register, max_cpu_core_num:4
  906. [ 4.881028@0] aml_istbt_dev_ready NULL
  907. [ 4.881089@0] ALSA device list:
  908. [ 4.882255@0] #0: AML-M8AUDIO
  909. [ 4.885974@0] Freeing unused kernel memory: 1168K (ffffffc001e02000 - ffffffc001f26000)
  910. [ 61.644732@0] random: nonblocking pool is initialized
RAW Paste Data

Adblocker detected! Please consider disabling it...

We've detected AdBlock Plus or some other adblocking software preventing Pastebin.com from fully loading.

We don't have any obnoxious sound, or popup ads, we actively block these annoying types of ads!

Please add Pastebin.com to your ad blocker whitelist or disable your adblocking software.

×