Lemuntu v1509 serial console

bus_id 0
bus_mfp 0
pmu_id 3
vddr_pmu_dcdc_cfg 5
ddr_clk 588
ddr_cap 1024
ddr_bits_width 0
rank 1
ddr_type 0
row_col 0
rdodt 1
wrodt 1
zpzq 12
uart_id 3
uart_baudrate 115200
uart_pad 0
jtag_pad 0
bootdev 34
version 1.1
scan 0
busid = 0bus_mfp = 0pmu_id = 3vddr_pmu_dcdc_cfg = 5
ddr_clk = 0x24c ddr_cap = 400 ddr_bits_width = 0 rank = 1 ddr_type = 0 row_col
consolse init :port  3, baudrate 115200 mfp 0
pmu init
busid = 0bus_mfp = 0pmu_id = 3vddr_pmu_dcdc_cfg = 5
g_current_bus = 00x51:0x8b4:0x8b4
0x39:0x325b:0x325b
0x14:0x88a
VERSION A:set val = 0x85af
0x14:0x85af:0x85af
0x62:0x0
0x15:0x6cae:0x6cae
0x16:0x334b:0x334b
ATC2609A_PMU_SYS_CTL3 = 16512
 ,s2 flag = 0
enter from s40x3f:0x1e3:0x1e3
check adfu
reg_val = 0x0ddr init
ddr_cap = 400  row_col = 0 row_col_detect = 68
DRAM init mode0,type0,1cs,x32,588MHz,0x334d.@150616_R...Ok:1024MByte Cap.
ddr size=1024MB
load app
load uboot: load address is 0x8000000, entry point is 0x8000040
in fourth
dvfs = 0xc583bb75
ddr scan = 0
dvfs maigc = 0x44564653, dvfs = 0xc583bb75

U-Boot 2015.04-g4f0c247-dirty (Sep 29 2015 - 05:56:28)Actions-Semi

DRAM:  mem-size=1024MB
1 GiB
PLL:core=0x311,dev=0x1164,bus=0x1c710000,bus1=0x2e004,display=0x164, spead=0x0
set kinfo addr = 3f700000
gpio=23,mode=0,val=0
gpio=25,mode=0,val=0
gpio=55,mode=0,val=0
pwm_init, blob 3defee08
PWM init, node 3872
not find HOSC dat = 0xffff
not find HOSC dat = 0xca
ret = 7104
owl: begin analysis pmu in device tree
node = 9464
owl: have for pmu in device tree , node =9464
pmu_config.bus_id = 0
pmu_config.dcdc_en_bm  = 14
pmu_config.dcdc_cfgs[0] = 0
pmu_config.dcdc_cfgs[1] = 11
pmu_config.dcdc_cfgs[2] = 10
pmu_config.dcdc_cfgs[3] = 5
pmu_config.ldo_en_bm  = 131
pmu_config.ldo_cfgs[0] = 1
pmu_config.ldo_cfgs[1] = 2
pmu_config.ldo_cfgs[2] = 0
pmu_config.ldo_cfgs[3] = 0
pmu_config.ldo_cfgs[4] = 0
pmu_config.ldo_cfgs[5] = 0
pmu_config.ldo_cfgs[6] = 0
pmu_config.ldo_cfgs[7] = 3
pmu_config.ldo_cfgs[8] = 0
pmu_config.ldo_cfgs[9] = 0
pmu_config.ldo_cfgs[10] = 0
pmu_config.ldo_cfgs[11] = 0
pmu_type = 2
pmu_config.pwm_config[0].pwm_val = 0x0
pmu_config.pwm_config[0].mfp.shift = 0
pmu_config.pwm_config[0].mfp.mask = 0
,pmu_config.pwm_config[0].mfp.val = 0
pmu_config.pwm_config[0].mfp.no = 0
pmu_config.pwm_config[1].pwm_val = 0x102c3f
pmu_config.pwm_config[1].mfp.shift = 38
pmu_config.pwm_config[1].mfp.mask = 7
,pmu_config.pwm_config[1].mfp.val = 3
pmu_config.pwm_config[1].mfp.no = 1
pmu_config.pwm_config[2].pwm_val = 0x10343f
pmu_config.pwm_config[2].mfp.shift = 38
pmu_config.pwm_config[2].mfp.mask = 7
,pmu_config.pwm_config[2].mfp.val = 3
pmu_config.pwm_config[2].mfp.no = 1
pwm1 val=0x102c3f
pwm2 val=0x10343f
0x51:0x8b4:0x8b4
0x39:0x325b:0x325b
dcdc_cfgs[1] = 11
0x11:0xe5cf:0xe5cf
0x12:0x2cae:0x2cae
0x13:0x334b:0x334b
0x17:0x8acf:0x8acf
0x18:0x254c:0x254c
0x19:0x338a:0x338a
pmu init finish!
begin to check power!
wall_mv=4270
----------the plug_stat is 0-NO_PLUG,1-WALL_PLUG,2-USB_PLUG:1
----------bat_voltage = 1019
bat_mv:1019
node_path[2]=/i2c@b0170000/atc2603c@65/atc260x-power
support type: both DCIN and USB
low_power_boot_choice is 0
support_minicharger:1
MMC:   error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
slot:0, error mmc_init
error:-1,owl_sd_init fail
error: SDC2 send CMD8, No rsp
error: SDC2 send CMD55, No rsp
SD0: 0, eMMC: 1 (eMMC)
Using default environment

bootmode = 0
emmc boot
** get_partition_info mmc1:6
** Partition 6 not valid on device 1 **
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
Failed to find mmc:0
bootlogo: if=mmc, dev=1
reading boot_logo.bmp.gz
reading new_gamma_data
Fail to load gamma
OWL VIDEO: power on
OWL VIDEO: wait res 998, 113301
OWL LCD: lcd init
fdtdec_get_lcd_par
fdtdec_pwm_get: fdtdec_pwm_get(3defee08, 8700, pwms, 0)
pwm_node=f20, pwm_chip.pwm_node=f20
pwm id = 0
pwm period = 50000
pwm polarity = 1
get_pwr_ctl backlight_en_gpios  0
OWL dsi: dsi init
buf->vaddr  0x3df04370 buf->paddr  0x3df04370
fdtdec_get_dsi_par0
Can't get dsi mode node
OWL dsi: fdt No dsi par
fdtdec_get_hdmi_par
fdtdec_get_hdmi_par: resolution  = 1080P60HZ
fdtdec enable lcd
get_pwr_ctl lcd_power_gpios  0
get_pwr_ctl lcd_reset_gpios  0
reset ok lcd_reset_gpios
pwm:request duty = 29296
pwm:request period_ns = 50000
open bl 1
fdtdec enable lcd ok 1
In:    serial
Out:   serial
Err:   serial
adckey: AUX0, channel=0
adckey: keynum=4
adc_val=50
Net:   owl_mac_parse_fdtdec,phy_addr 1
owl_mac_parse_fdtdec,power-gpio 43
owl_mac_parse_fdtdec,reset-gpio 127
owl_mac
Error: owl_mac address 73:00:73:65:74:65 illegal value
, usb_ether
Error: usb_ether address not set.

Hit any key to stop autoboot:  0
try boot from mmc card ...
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
** Bad device mmc 0 **
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
** Bad device mmc 0 **
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
** Bad device mmc 0 **
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
** Bad device mmc 0 **
boot from emmc card ...
reading uEnv.txt
200 bytes read in 2 ms (97.7 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading boot.scr
** Unable to read file boot.scr **
reading uImage
5657976 bytes read in 250 ms (21.6 MiB/s)
reading kernel.dtb
34464 bytes read in 5 ms (6.6 MiB/s)
## Booting kernel from Legacy Image at 00007fc0 ...
   Image Name:   Linux-3.10.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5657912 Bytes = 5.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
   Booting using the fdt blob at 0x4000000
   XIP Kernel Image ... OK
   Using Device Tree in place at 04000000, end 0400b69f
owl_boot_fdt_setup linux
devpart 1:1
boot_dev=sd2read_mi_head, line 429, magic 0x0, length 0, item num 0
read Head null
read SN failed
cmdline: console=ttyS3 earlyprintk clk_ignore_unused selinux=0 scandelay root=/2

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.37 (peter@ubuntu) (gcc version 4.7.3 201303285
[    0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie
[    0.000000] Machine: gs705a, model: Actions GS705A board

[    0.000000] bootconsole [earlycon0] enabled
[    0.530220] i2c i2c-2: of_i2c: invalid reg on /i2c@b0178000/mpu6515@68
[    0.570306] owl pinctrl: 1gpio_request_check_pinmux
[    0.575226] owl pinctrl: 1CHECK PMX:P_KS_IN2 has already been requested by gt
[    0.595828] atc260x_i2c 0-0065: icm_ohm not config, use default value
[    0.639482] atc260x-switch-ldo atc2603c-switch1.1: pmic_ver=0
[    0.659514] atc260x-pm atc2603c-pm.0: _set_s2_mode() can not get of_property
[    0.928331] owl_dss LCDC: error!lcdchw_parse_params, fail to get lcd standbyo
[    0.936043] owl pinctrl: 1gpio_request_check_pinmux
[    0.941112] owl pinctrl: 1CHECK PMX:P_LVDS_OBN has already been requested by0
[    0.952195] OWL_HDMI_ERR: cat not get vid480p_tx1
[    1.006717] no blk dev
[    1.009113] read MiscInfoHeader failed
[    1.012882] read Head failed
[    1.015780] OWL_HDMI_ERR: failed to read hdcp key from secure storage
[    1.067923] aotg_hcd b0600000.usb: can't find usbh-1 dts node
[    1.073741] aotg_hcd b0600000.usb: aotg_hub_probe: usb probe hcd  failed, er9
[    1.082255] aotg_hcd b0700000.usb: can't find usbh-1 dts node
[    1.088120] aotg_hcd b0700000.usb: aotg_hub_probe: usb probe hcd  failed, er9
[    1.113461] atc260x-rtc atc2603c-rtc.0: invalid year(0), reset to year 2011
[    1.131089] pinctrl-owl pinctrl.1: pin P_SD0_D0 already requested by b012a00c
[    1.141697] pinctrl-owl pinctrl.1: pin-74 (b0230000.mmc) status -22
[    1.148102] pinctrl-owl pinctrl.1: could not request pin 74 on device pinctr1
[    1.155475] gl520x_mmc b0230000.mmc: Error applying setting, reverse things k
[    1.171387] owl pinctrl: 1gpio_request_check_pinmux
[    1.176493] owl pinctrl: 1CHECK PMX:P_LVDS_ODP has already been requested by0
[    1.205531] [SNDRV]:[atc2603a_get_cfg] Fail to get device_node
[    1.205531]
[    1.213072] [SNDRV]:[atc2603a_init] audio get cfg failed!
[    1.213072]
[    1.220290] [SNDRV]:[atc2603c_get_cfg] get gpio[speaker_en_gpios] fail
[    1.220290]
[    1.229291] [SNDRV]:[atc2603c_platform_probe] atc2603c_platform_probe
[    1.229291]
[    1.237466] [SNDRV]:[atc2603c_platform_probe] what's my lucky draw 227
[    1.237466]
[    1.246864] [SNDRV]:[atm7059_dai_probe] it's ok 0
[    1.246864]
[    1.254355] [SNDRV]:[atm7059_link_init] atm7059_link_init
[    1.254355]
[    1.262021] [SNDRV]:[atm7059_audio_gpio_init] find earphone_detect_gpios prol
[    1.262021]
[    1.271732] [SNDRV]:[atm7059_audio_gpio_init] find speaker_en_gpios propertyl
[    1.271732]
[    1.281006] [SNDRV]:[atm7059_link_init] maybe using irq
[    1.432657] atc2603c-audio atc260x-audio: ASoC: Failed to add route AOUT FL x
[    1.474029] train_Msize:1024, train_ces:1
[    1.516152] start:0xc0008000, end:0xc0a28bc8, checksum:0x1c8991c7
[    1.634721] store_mirror_to_hdmi 1
[    1.677167] store_mirror_to_hdmi 1
[    1.681096] store_mirror_to_hdmi 1
[    1.695378] store_mirror_to_hdmi 1
[    1.709290] store_mirror_to_hdmi 1
[    1.722913] store_mirror_to_hdmi 1
[    1.736135] store_mirror_to_hdmi 1

Welcome to Debian GNU/Linux 8 (jessie)!

         Expecting device dev-ttyS3.device...
[  OK  ] Reached target Remote File Systems (Pre).
[  OK  ] Reached target Paths.
[  OK  ] Reached target Encrypted Volumes.
[  OK  ] Reached target Swap.
[  OK  ] Created slice Root Slice.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Listening on Delayed Shutdown Socket.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on udev Control Socket.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on Journal Socket.
[  OK  ] Created slice System Slice.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
         Starting Increase datagram queue length...
         Starting Create list of required static device nodes...rrent kernel...
         Starting udev Coldplug all Devices...
         Starting Load Kernel Modules...
         Mounting Debug File System...
[  OK  ] Reached target Slices.
[  OK  ] Mounted Debug File System.
[  OK  ] Started Increase datagram queue length.
[  OK  ] Started Create list of required static device nodes ...current kernel.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started udev Coldplug all Devices.
         Mounting Configuration File System...
         Mounting FUSE Control File System...
         Starting Apply Kernel Variables...
         Starting Create Static Device Nodes in /dev...
[  OK  ] Listening on Syslog Socket.
         Starting Journal Service...
[  OK  ] Started Journal Service.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Mounted Configuration File System.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Started udev Kernel Device Manager.
         Starting Copy rules generated while the root was ro...
         Starting LSB: Set preliminary keymap...
[  OK  ] Started Copy rules generated while the root was ro.
[  OK  ] Started LSB: Set preliminary keymap.
         Starting Remount Root and Kernel File Systems...
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Found device /dev/ttyS3.
[    3.421168] atc260x-irkeypad atc2603c-irkeypad.0: Get ir_ch failed ret = -22
         Starting Load/Save Random Seed...
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
[    3.504332] owl pinctrl: 1gpio_request_check_pinmux
         Starting[    3.512467] owl pinctrl: 1CHECK PMX:P_UART3_CTSB has alreada
[    3.523325] owl pinctrl: 1gpio_request_check_pinmux
nd Directories...
[    3.534357] owl pinctrl: 1CHECK PMX:P_UART3_RTSB has already been requested l
[    3.544006] [owl_camera] (ERR) line:1935--gpio_init() <isp>no config gpios
[  OK  ] Reached target Remote File Systems.
[    3.566171] read_mi_head, line 429, magic 0x0, length 0, item num 0
[    3.575982] read Head null
         Starting Trigger Flushing of Journal to Persistent Storage...
         Starting LSB: Set console font and keymap...
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started LSB: Set console font and keymap.
[  OK  ] Started Create Volatile Files and Directories.
[  OK  ] Started Trigger Flushing of Journal to Persistent Storage.
[  OK  ] Created slice system-systemd\x2drfkill.slice.
         Starting Load/Save RF Kill Switch Status of rfkill0...
[  OK  ] Reached target Sound Card.
[  OK  ] Created slice system-systemd\x2dbacklight.slice.
         Starting Load/Save Screen Backlight Brightness of ba...:backlight.2...
         Starting Update UTMP about System Boot/Shutdown...
         Starting LSB: Raise network interfaces....
[  OK  ] Started Load/Save RF Kill Switch Status of rfkill0.
[  OK  ] Started Load/Save Screen Backlight Brightness of bac...ht:backlight.2.
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started LSB: Raise network interfaces..
[  OK  ] Reached target Network.
[  OK  ] Reached target Network is Online.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Timers.
         Starting Restore Sound Card State...
[  OK  ] Reached target Basic System.
         Starting Regular background program processing daemon...
[  OK  ] Started Regular background program processing daemon.
         Starting OpenBSD Secure Shell server...
[  OK  ] Started OpenBSD Secure Shell server.
         Starting Deferred execution scheduler...
[  OK  ] Started Deferred execution scheduler.
         Starting /etc/rc.local Compatibility...
         Starting Login Service...
         Starting LSB: Start NTP daemon...
         Starting D-Bus System Message Bus...
[  OK  ] Started D-Bus System Message Bus.
         Starting System Logging Service...
         Starting Permit User Sessions...
[  OK  ] Started Restore Sound Card State.
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started LSB: Start NTP daemon.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started System Logging Service.
         Starting Light Display Manager...
         Starting Getty on tty1...
[  OK  ] Started Getty on tty1.
         Starting Serial Getty on ttyS3...
[  OK  ] Started Serial Getty on ttyS3.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Login Service.
[  OK  ] Reached target Multi-User System.
[  OK  ] Started Light Display Manager.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Debian GNU/Linux 8 Lemuntu ttyS3

Lemuntu login: