Advertisement
Guest User

Untitled

a guest
Nov 10th, 2018
233
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 8.97 KB | None | 0 0
  1.  
  2. === START OF READ SMART DATA SECTION ===
  3. SMART Status not supported: Incomplete response, ATA output registers missing
  4. SMART overall-health self-assessment test result: PASSED
  5. Warning: This result is based on an Attribute check.
  6.  
  7. General SMART Values:
  8. Offline data collection status: (0x00) Offline data collection activity
  9. was never started.
  10. Auto Offline Data Collection: Disabled.
  11. Self-test execution status: ( 0) The previous self-test routine completed
  12. without error or no self-test has ever
  13. been run.
  14. Total time to complete Offline
  15. data collection: (37140) seconds.
  16. Offline data collection
  17. capabilities: (0x7b) SMART execute Offline immediate.
  18. Auto Offline data collection on/off support.
  19. Suspend Offline collection upon new
  20. command.
  21. Offline surface scan supported.
  22. Self-test supported.
  23. Conveyance Self-test supported.
  24. Selective Self-test supported.
  25. SMART capabilities: (0x0003) Saves SMART data before entering
  26. power-saving mode.
  27. Supports SMART auto save timer.
  28. Error logging capability: (0x01) Error logging supported.
  29. General Purpose Logging supported.
  30. Short self-test routine
  31. recommended polling time: ( 2) minutes.
  32. Extended self-test routine
  33. recommended polling time: ( 410) minutes.
  34. Conveyance self-test routine
  35. recommended polling time: ( 5) minutes.
  36. SCT capabilities: (0x7035) SCT Status supported.
  37. SCT Feature Control supported.
  38. SCT Data Table supported.
  39.  
  40. SMART Attributes Data Structure revision number: 16
  41. Vendor Specific SMART Attributes with Thresholds:
  42. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  43. 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 77
  44. 3 Spin_Up_Time 0x0027 193 187 021 Pre-fail Always - 5350
  45. 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 912
  46. 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
  47. 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 1
  48. 9 Power_On_Hours 0x0032 078 078 000 Old_age Always - 16608
  49. 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  50. 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  51. 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 604
  52. 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 583
  53. 193 Load_Cycle_Count 0x0032 166 166 000 Old_age Always - 103599
  54. 194 Temperature_Celsius 0x0022 116 108 000 Old_age Always - 36
  55. 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
  56. 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 152
  57. 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
  58. 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
  59. 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
  60.  
  61. SMART Error Log Version: 1
  62. ATA Error Count: 81 (device log contains only the most recent five errors)
  63. CR = Command Register [HEX]
  64. FR = Features Register [HEX]
  65. SC = Sector Count Register [HEX]
  66. SN = Sector Number Register [HEX]
  67. CL = Cylinder Low Register [HEX]
  68. CH = Cylinder High Register [HEX]
  69. DH = Device/Head Register [HEX]
  70. DC = Device Command Register [HEX]
  71. ER = Error register [HEX]
  72. ST = Status register [HEX]
  73. Powered_Up_Time is measured from power on, and printed as
  74. DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
  75. SS=sec, and sss=millisec. It "wraps" after 49.710 days.
  76.  
  77. Error 81 occurred at disk power-on lifetime: 12825 hours (534 days + 9 hours)
  78. When the command that caused the error occurred, the device was active or idle.
  79.  
  80. After command completion occurred, registers were:
  81. ER ST SC SN CL CH DH
  82. -- -- -- -- -- -- --
  83. 04 61 00 00 00 00 00 Device Fault; Error: ABRT
  84.  
  85. Commands leading to the command that caused the error were:
  86. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  87. -- -- -- -- -- -- -- -- ---------------- --------------------
  88. ef 02 00 00 00 00 00 00 1d+16:18:16.053 SET FEATURES [Enable write cache]
  89. ef 90 06 00 00 00 00 00 1d+16:18:16.053 SET FEATURES [Disable SATA feature]
  90. e1 00 02 00 00 00 00 00 1d+16:18:16.052 IDLE IMMEDIATE
  91. ec 00 01 00 00 00 00 00 1d+16:18:16.052 IDENTIFY DEVICE
  92. e0 00 0a 00 00 00 00 00 1d+04:56:26.602 STANDBY IMMEDIATE
  93.  
  94. Error 80 occurred at disk power-on lifetime: 12825 hours (534 days + 9 hours)
  95. When the command that caused the error occurred, the device was active or idle.
  96.  
  97. After command completion occurred, registers were:
  98. ER ST SC SN CL CH DH
  99. -- -- -- -- -- -- --
  100. 04 61 06 00 00 00 00 Device Fault; Error: ABRT
  101.  
  102. Commands leading to the command that caused the error were:
  103. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  104. -- -- -- -- -- -- -- -- ---------------- --------------------
  105. ef 90 06 00 00 00 00 00 1d+16:18:16.053 SET FEATURES [Disable SATA feature]
  106. e1 00 02 00 00 00 00 00 1d+16:18:16.052 IDLE IMMEDIATE
  107. ec 00 01 00 00 00 00 00 1d+16:18:16.052 IDENTIFY DEVICE
  108. e0 00 0a 00 00 00 00 00 1d+04:56:26.602 STANDBY IMMEDIATE
  109.  
  110. Error 79 occurred at disk power-on lifetime: 12825 hours (534 days + 9 hours)
  111. When the command that caused the error occurred, the device was active or idle.
  112.  
  113. After command completion occurred, registers were:
  114. ER ST SC SN CL CH DH
  115. -- -- -- -- -- -- --
  116. 04 61 02 00 00 00 00
  117.  
  118. Commands leading to the command that caused the error were:
  119. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  120. -- -- -- -- -- -- -- -- ---------------- --------------------
  121. e1 00 02 00 00 00 00 00 1d+16:18:16.052 IDLE IMMEDIATE
  122. ec 00 01 00 00 00 00 00 1d+16:18:16.052 IDENTIFY DEVICE
  123. e0 00 0a 00 00 00 00 00 1d+04:56:26.602 STANDBY IMMEDIATE
  124. b0 d0 00 00 4f c2 00 00 1d+04:55:46.338 SMART READ DATA
  125.  
  126. Error 78 occurred at disk power-on lifetime: 12813 hours (533 days + 21 hours)
  127. When the command that caused the error occurred, the device was active or idle.
  128.  
  129. After command completion occurred, registers were:
  130. ER ST SC SN CL CH DH
  131. -- -- -- -- -- -- --
  132. 04 61 0a 00 00 00 00
  133.  
  134. Commands leading to the command that caused the error were:
  135. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  136. -- -- -- -- -- -- -- -- ---------------- --------------------
  137. e0 00 0a 00 00 00 00 00 1d+04:56:26.602 STANDBY IMMEDIATE
  138. b0 d0 00 00 4f c2 00 00 1d+04:55:46.338 SMART READ DATA
  139. b0 d0 00 00 4f c2 00 00 1d+04:51:36.707 SMART READ DATA
  140. b0 d0 00 00 4f c2 00 00 1d+04:47:27.075 SMART READ DATA
  141.  
  142. Error 77 occurred at disk power-on lifetime: 12813 hours (533 days + 21 hours)
  143. When the command that caused the error occurred, the device was active or idle.
  144.  
  145. After command completion occurred, registers were:
  146. ER ST SC SN CL CH DH
  147. -- -- -- -- -- -- --
  148. 04 61 00 00 00 00 00 Device Fault; Error: ABRT
  149.  
  150. Commands leading to the command that caused the error were:
  151. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  152. -- -- -- -- -- -- -- -- ---------------- --------------------
  153. ef 02 00 00 00 00 00 00 1d+04:30:53.758 SET FEATURES [Enable write cache]
  154. ef 90 06 00 00 00 00 00 1d+04:30:53.758 SET FEATURES [Disable SATA feature]
  155. e1 00 02 00 00 00 00 00 1d+04:30:53.757 IDLE IMMEDIATE
  156. ec 00 01 00 00 00 00 00 1d+04:30:53.757 IDENTIFY DEVICE
  157. b0 d0 00 00 4f c2 00 00 1d+04:26:38.916 SMART READ DATA
  158.  
  159. SMART Self-test log structure revision number 1
  160. No self-tests have been logged. [To run self-tests, use: smartctl -t]
  161.  
  162. SMART Selective self-test log data structure revision number 1
  163. SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
  164. 1 0 0 Not_testing
  165. 2 0 0 Not_testing
  166. 3 0 0 Not_testing
  167. 4 0 0 Not_testing
  168. 5 0 0 Not_testing
  169. Selective self-test flags (0x0):
  170. After scanning selected spans, do NOT read-scan remainder of disk.
  171. If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement