Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.4 (Jun 7 2016 - 16:58:04)
- ap151 - Dragonfly 1.0
- DRAM: 64 MB
- Top of RAM usable for U-Boot at: 84000000
- Reserving 341k for U-Boot at: 83fa8000
- Reserving 32832k for malloc() at: 81f98000
- Reserving 44 Bytes for Board Info at: 81f97fd4
- Reserving 36 Bytes for Global Data at: 81f97fb0
- Reserving 128k for boot params() at: 81f77fb0
- Stack Pointer at: 81f77f98
- Now running in RAM - U-Boot at: 83fa8000
- Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
- flash size 8MB, sector count = 128
- Flash: 8 MB
- Using default environment
- In: serial
- Out: serial
- Err: serial
- Net: ath_gmac_enet_initialize...
- No valid address in Flash. Using fixed address
- No valid address in Flash. Using fixed address
- ath_gmac_enet_initialize: reset mask:c02200
- Dragonfly----> S27 PHY *
- : cfg1 0x80000000 cfg2 0x7114
- eth0: 00:03:7f:09:0b:ad
- athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
- eth0 up
- ATHRS27: resetting s27
- ATHRS27: s27 reset done
- : cfg1 0x800c0000 cfg2 0x7214
- eth1: 00:03:7f:09:0b:ad
- athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :50
- athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :50
- athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :50
- athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :50
- eth1 up
- eth0, eth1
- Setting 0x181162c0 to 0x82
- Autobooting in 1 seconds
- ath> ?
- ? - alias for 'help'
- boot - boot default, i.e., run 'bootcmd'
- bootd - boot default, i.e., run 'bootcmd'
- bootm - boot application image from memory
- cp - memory copy
- erase - erase FLASH memory
- fwrecov - TP-Link Firmware Recovery Tools
- help - print online help
- mct - simple RAM test
- md - memory display
- mm - memory modify (auto-incrementing)
- mtest - simple RAM test
- mw - memory write (fill)
- nm - memory modify (constant address)
- ping - send ICMP ECHO_REQUEST to network host
- printenv- print environment variables
- reset - Perform RESET of the CPU
- run - run commands in an environment variable
- setenv - set environment variables
- tftpboot- boot image via network using TFTP protocol
- version - print monitor version
- ath> printenv
- bootargs=console=ttyS0,115200 board=AP151 rootfstype=squashfs init=/etc/preinit mtdparts=spi0.0:128k(u-boot)
- ,1056k(uImage),6944k(rootfs),64k@0x7f0000(ART) mem=64M
- bootcmd=bootm 0x9f020000
- bootdelay=1
- baudrate=115200
- ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
- ipaddr=192.168.0.2
- serverip=192.168.0.10
- dir=
- lu=tftp 0x80060000 ${dir}tuboot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
- lf=tftp 0x80060000 ${dir}ap151${bc}-jffs2&&erase 0x9f010000 +$filesize&&cp.b $fileaddr 0x9f010000 $filesize
- lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f300000 +$filesize&&cp.b $fileaddr 0x9f300000 $f
- ilesize
- stdin=serial
- stdout=serial
- stderr=serial
- ethact=eth0
- Environment size: 679/65532 bytes
- ath>
Add Comment
Please, Sign In to add comment