Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BUFFALO CFE Version 1.00 [DDRCLK:533]
- Memory Test start(0x07E00000) end(0x08000000) size(2097152)
- Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 533 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
- gateway not set, nameserver not set
- Startup canceled
- CFE> flash -noheader 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin nflash1.trx
- Reading 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin: Done. 24285184 bytes read
- Programming...done. 24285184 bytes written
- *** command status = 0
- CFE> flash -noheader 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin nflash1.trx
- Reading 192.168.11.2:buffalo-wzr-1750dhp-webflash.bin: Done. 24285184 bytes read
- Programming...done. 24285184 bytes written
- *** command status = 0
- CFE> nvram erase
- *** command status = 0
- CFE> reboot
- BUFFALO CFE Version 1.00 [DDRCLK:333]
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- Corrupt NVRAM found, trying embedded NVRAM next.
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 333 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- Warning: invalid DDR setting of 533 MHz ignored. DDR frequency will be set to 333 MHz.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- initializing nvram...Corrupt NVRAM found, trying embedded NVRAM next.
- done
- commiting nvram...done
- now rebooting
- BUFFALO CFE Version 1.00 [DDRCLK:333]
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- DDR clock change and Calibrate... [333->533]
- BUFFALO CFE Version 1.00 [DDRCLK:533]
- Memory Test start(0x07E00000) end(0x08000000) size(2097152)
- Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 533 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- Committing NVRAM...done
- Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
- gateway not set, nameserver not set
- check_trx: start nflash1.trx
- check_trx: exit nflash1.trx
- Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
- Loading: .. 1286104 bytes read
- Entry at 0x00008000
- Closing network.
- Starting program at 0x00008000
- Uncompressing Linux... done, booting the kernel.
- Booting Linux on physical CPU 0x0
- Linux version 3.10.30 (root@dd-wrt.buildserver) (gcc version 4.8.2 (OpenWrt/Linaro GCC 4.8-2013.10 r38451) ) #1533 SMP Wed Feb 19 05:53:26 CET 2014
- CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
- CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine: Northstar Prototype
- Ignoring unrecognised tag 0x00000000
- Memory policy: ECC disabled, Data cache writealloc
- map io
- MPCORE found at 19020000 (VIRT d9020000) 18000000 d8000000
- PERCPU: Embedded 7 pages/cpu @c1808000 s7040 r8192 d13440 u32768
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130816
- Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock3 earlyprintk=1 rootfstype=squashfs,jffs2 noinitrd init=/bin/sh
- PID hash table entries: 512 (order: -1, 2048 bytes)
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Memory: 128MB 384MB = 512MB total
- Memory: 515892k/515892k available, 8396k reserved, 393216K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
- lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
- pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- .text : 0xc0008000 - 0xc0320da4 (3172 kB)
- .init : 0xc0321000 - 0xc035ab80 ( 231 kB)
- .data : 0xc035c000 - 0xc03987fc ( 242 kB)
- .bss : 0xc03987fc - 0xc03f8e18 ( 386 kB)
- Hierarchical RCU implementation.
- CONFIG_RCU_FANOUT set to non-default value of 2
- NR_IRQS:256
- MPCORE GIC init
- External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
- MPCORE Global Timer Clock 400000000Hz on IRQ 27
- sched_clock: 32 bits at 400MHz, resolution 2ns, wraps every 10737ms
- register local timer
- smp_twd: clock not found -2
- Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- Calibrating local timer... 399.68MHz.
- 2 cores has been found
- Setting up static identity map for 0xc0012440 - 0xc0012474
- L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
- CPU1: Booted secondary processor
- CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- Brought up 2 CPUs
- SMP: Total of 2 processors activated (3188.32 BogoMIPS).
- NET: Registered protocol family 16
- DMA: preallocated 256 KiB pool for atomic coherent allocations
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- found remapped nvram on sflash
- CCA UART Clock Config: Sel=1 Ovr=1 Div=48
- CCA UART Clock rate 100000000Hz
- bio: create slab <bio-0> at 0
- Switching to clocksource mpcore_gtimer
- NET: Registered protocol family 2
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP: reno registered
- UDP hash table entries: 256 (order: 1, 8192 bytes)
- UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- NET: Registered protocol family 1
- init gpio code
- Buffalo WZR-1750DHP
- PCI: no core
- PCI: no core
- PCI: scanning bus 0
- PCI host bridge to bus 0000:00
- pci_bus 0000:00: root bus resource [io 0x0000-0xffffffff]
- pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
- pci_bus 0000:00: root bus resource [bus 00-ff]
- PCI: Fixing up bus 0
- PCIE1 link=1
- PCIE1 switching to GEN2
- PCIE1 link=1
- PCI host bridge to bus 0001:00
- pci_bus 0001:00: root bus resource [mem 0x08000000-0x0fffffff]
- pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
- PCI: Fixing up bus 0
- PCI: bus0: Fast back to back transfers disabled
- PCI: Fixing up bus 1
- PCI: bus1: Fast back to back transfers disabled
- pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
- pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
- pci 0001:00:00.0: PCI bridge to [bus 01]
- pci 0001:00:00.0: bridge window [mem 0x08000000-0x080fffff]
- PCIE2 link=1
- PCIE2 switching to GEN2
- PCIE2 link=1
- PCI host bridge to bus 0002:00
- pci_bus 0002:00: root bus resource [mem 0x40000000-0x47ffffff]
- pci_bus 0002:00: No busn resource found for root bus, will use [bus 00-ff]
- PCI: Fixing up bus 0
- PCI: bus0: Fast back to back transfers disabled
- PCI: Fixing up bus 2
- PCI: bus2: Fast back to back transfers disabled
- pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
- pci 0002:02:00.0: BAR 0: assigned [mem 0x40000000-0x40003fff 64bit]
- pci 0002:00:00.0: PCI bridge to [bus 02]
- pci 0002:00:00.0: bridge window [mem 0x40000000-0x400fffff]
- PCIE3 link=0
- Error creating gpio class
- squashfs: version 3.0 (2006/03/15) Phillip Lougher
- msgmni has been set to 239
- alg: No test for stdrng (krng)
- io scheduler noop registered (default)
- io scheduler cfq registered
- Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
- console [ttyS0] enabled
- serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
- brd: module loaded
- loop: module loaded
- Creating 5 MTD partitions on "bcmsflash":
- 0x000000000000-0x000000100000 : "boot"
- 0x000000000000-0x0000000f0000 : "linux"
- 0x000000100000-0x000000100000 : "rootfs"
- mtd: partition "rootfs" is out of reach -- disabled
- 0x0000000f0000-0x000000100000 : "nvram_cfe"
- 0x0000000e0000-0x0000000f0000 : "nvram"
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8 (8-bit)
- Device ID: 0x92 0xf1 0x80 0x95 0x40 0x7f
- Creating 1 MTD partitions on "nflash":
- 0x000000000000-0x000008000000 : "nand"
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- PPP Deflate Compression module registered
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- GACT probability NOT on
- Mirror/redirect action on
- Failed to load ipt action
- Simple TC action Loaded
- netem: version 1.3
- u32 classifier
- Performance counters on
- input device check on
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (8060 buckets, 32240 max)
- nf_conntrack_rtsp v0.6.21 loading
- xt_time: kernel timezone is -0000
- ip_set: protocol 6
- gre: GRE over IPv4 demultiplexor driver
- nf_nat_rtsp v0.6.21 loading
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP: bic registered
- TCP: cubic registered
- TCP: westwood registered
- TCP: highspeed registered
- TCP: hybla registered
- TCP: htcp registered
- TCP: vegas registered
- TCP: veno registered
- TCP: scalable registered
- TCP: lp registered
- TCP: yeah registered
- TCP: illinois registered
- NET: Registered protocol family 17
- Bridge firewalling registered
- 8021q: 802.1Q VLAN Support v1.8
- found cfe nvram
- Key type encrypted registered
- Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
- NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
- Spare area=64 eccbytes 56, ecc bytes located at:
- 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
- Available 7 bytes at (off,len):
- (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0)
- Driver must set ecc.strength when using hardware ECC
- Scanning device for bad blocks
- Options: NO_SUBPAGE_WRITE,
- Creating 1 MTD partitions on "brcmnand":
- 0x000000000000-0x000008000000 : "ddwrt"
- end_request: I/O error, dev mtdblock2, sector 0
- SQUASHFS error: sb_bread failed reading block 0x0
- VFS: Cannot open root device "1f02" or unknown-block(31,2): error -19
- Please append a correct "root=" boot option; here are the available partitions:
- 1f00 1024 mtdblock0 (driver?)
- 1f01 960 mtdblock1 (driver?)
- 1f03 64 mtdblock3 (driver?)
- 1f04 64 mtdblock4 (driver?)
- 1f05 131072 mtdblock5 (driver?)
- 1f06 131072 mtdblock6 (driver?)
- Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
- CPU1: stopping
- CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.30 #1533
- Backtrace:
- Function entered at [<c00157d8>] from [<c0015994>]
- r6:00000000 r5:00000001 r4:c0359b60 r3:00000000
- Function entered at [<c001597c>] from [<c0126e08>]
- Function entered at [<c0126de4>] from [<c001725c>]
- Function entered at [<c001717c>] from [<c00086d8>]
- r6:c7857f70 r5:c0370640 r4:f010010c r3:c001355c
- Function entered at [<c0008678>] from [<c0008860>]
- Exception stack(0xc7857f70 to 0xc7857fb8)
- 7f60: c1810778 00000000 00000ba2 00000000
- 7f80: c7856000 c7856000 c0370470 c02d5be0 c7856000 c0377b67 c0377b67 c7857fc4
- 7fa0: c7857fc8 c7857fb8 c001355c c0013560 60000113 ffffffff
- r7:c7857fa4 r6:ffffffff r5:60000113 r4:c0013560
- Function entered at [<c0013530>] from [<c005cc18>]
- Function entered at [<c005cb40>] from [<c033d1f8>]
- r7:c03991a8 r3:00000002
- Function entered at [<c033d0bc>] from [<0033c860>]
- r4:0783806a r3:c033c848
- Rebooting in 10 seconds..
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement