SHARE
TWEET

Untitled

a guest Jun 16th, 2019 93 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot 2016.03-g80540a2-dirty (Mar 15 2019 - 16:43:43 +0800)
  2.  
  3. CPU:   Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
  4. CPU:   Commercial temperature grade (0C to 105C) at 46C
  5. Reset cause: POR
  6. Board: MYS-MX6ULL 14x14
  7. I2C:   ready
  8. DRAM:  256 MiB
  9. force_idle_bus: sda=0 scl=0 sda.gp=0x1d scl.gp=0x1c
  10. force_idle_bus: failed to clear bus, sda=0 scl=0
  11. MMC:   FSL_SDHC: 0, FSL_SDHC: 1
  12. Card doesn't support part_switch
  13. MMC partition switch failed
  14. *** Warning - MMC partition switch failed, using default environment
  15.      
  16. Booting Linux on physical CPU 0x0
  17. Linux version 4.1.15+ (sacrasystems@ubuntu) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon May 20 10:11:32 IST 2019
  18. CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
  19. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  20. Machine model: Freescale i.MX6 ULL 14x14 EVK Board
  21. Reserved memory: failed to allocate memory for node 'linux,cma'
  22. Memory policy: Data cache writealloc
  23. On node 0 totalpages: 65536
  24. free_area_init_node: node 0, pgdat 80c10cc0, node_mem_map 8fdf7000
  25.   Normal zone: 512 pages used for memmap
  26.   Normal zone: 0 pages reserved
  27.   Normal zone: 65536 pages, LIFO batch:15
  28. PERCPU: Embedded 12 pages/cpu @8fdd4000 s16908 r8192 d24052 u49152
  29. pcpu-alloc: s16908 r8192 d24052 u49152 alloc=12*4096
  30. pcpu-alloc: [0] 0
  31. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
  32. Kernel command line: console=ttymxc0,115200 fstype=ext4 root=/dev/mmcblk0p2
  33. PID hash table entries: 1024 (order: 0, 4096 bytes)
  34. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  35. Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  36. Memory: 246888K/262144K available (8509K kernel code, 439K rwdata, 2948K rodata, 428K init, 450K bss, 15256K reserved, 0K cma-reserved, 0K highmem)
  37. Virtual kernel memory layout:
  38.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  39.     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
  40.     vmalloc : 0x90800000 - 0xff000000   (1768 MB)
  41.     lowmem  : 0x80000000 - 0x90000000   ( 256 MB)
  42.     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
  43.     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
  44.       .text : 0x80008000 - 0x80b386e4   (11458 kB)
  45.       .init : 0x80b39000 - 0x80ba4000   ( 428 kB)
  46.       .data : 0x80ba4000 - 0x80c11ea0   ( 440 kB)
  47.        .bss : 0x80c14000 - 0x80c84b00   ( 451 kB)
  48. SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  49. Preemptible hierarchical RCU implementation.
  50.         Additional per-CPU info printed with stalls.
  51.         RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
  52. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
  53. NR_IRQS:16 nr_irqs:16 16
  54. mxc_clocksource_init 24000000
  55. Switching to timer-based delay loop, resolution 41ns
  56. sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
  57. clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
  58. Console: colour dummy device 80x30
  59. Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  60. pid_max: default: 32768 minimum: 301
  61. Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  62. Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  63. CPU: Testing write buffer coherency: ok
  64. /cpus/cpu@0 missing clock-frequency property
  65. CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  66. Setting up static identity map for 0x80008280 - 0x800082d8
  67. Brought up 1 CPUs
  68. SMP: Total of 1 processors activated (48.00 BogoMIPS).
  69. CPU: All CPU(s) started in SVC mode.
  70. devtmpfs: initialized
  71. device-tree: Duplicate name in lcdif@021c8000, renamed to "display#1"
  72. VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  73. clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  74. pinctrl core: initialized pinctrl subsystem
  75. NET: Registered protocol family 16
  76. DMA: preallocated 256 KiB pool for atomic coherent allocations
  77. cpuidle: using governor ladder
  78. cpuidle: using governor menu
  79. hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  80. hw-breakpoint: maximum watchpoint size is 8 bytes.
  81. imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
  82. imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
  83. mxs-dma 1804000.dma-apbh: initialized
  84. SCSI subsystem initialized
  85. libata version 3.00 loaded.
  86. usbcore: registered new interface driver usbfs
  87. usbcore: registered new interface driver hub
  88. usbcore: registered new device driver usb
  89. i2c i2c-1: IMX I2C adapter registered
  90. i2c i2c-1: can't use DMA
  91. media: Linux media interface: v0.10
  92. Linux video capture interface: v2.00
  93. pps_core: LinuxPPS API ver. 1 registered
  94. pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  95. PTP clock support registered
  96. MIPI CSI2 driver module loaded
  97. Advanced Linux Sound Architecture Driver Initialized.
  98. Bluetooth: Core ver 2.20
  99. NET: Registered protocol family 31
  100. Bluetooth: HCI device and connection manager initialized
  101. Bluetooth: HCI socket layer initialized
  102. Bluetooth: L2CAP socket layer initialized
  103. Bluetooth: SCO socket layer initialized
  104. Switched to clocksource mxc_timer1
  105. NET: Registered protocol family 2
  106. TCP established hash table entries: 2048 (order: 1, 8192 bytes)
  107. TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
  108. TCP: Hash tables configured (established 2048 bind 2048)
  109. UDP hash table entries: 256 (order: 1, 8192 bytes)
  110. UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  111. NET: Registered protocol family 1
  112. RPC: Registered named UNIX socket transport module.
  113. RPC: Registered udp transport module.
  114. RPC: Registered tcp transport module.
  115. RPC: Registered tcp NFSv4.1 backchannel transport module.
  116. imx rpmsg driver is registered.
  117. Bus freq driver module loaded
  118. futex hash table entries: 256 (order: 2, 16384 bytes)
  119. VFS: Disk quotas dquot_6.6.0
  120. VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  121. NFS: Registering the id_resolver key type
  122. Key type id_resolver registered
  123. Key type id_legacy registered
  124. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  125. fuse init (API version 7.23)
  126. io scheduler noop registered
  127. io scheduler deadline registered
  128. io scheduler cfq registered (default)
  129. imx-weim 21b8000.weim: Driver registered.
  130. backlight supply power not found, using dummy regulator
  131. MIPI DSI driver module loaded
  132. MIPI DSI driver module loaded
  133. 21c8000.lcdif supply lcd not found, using dummy regulator
  134. mxsfb 21c8000.lcdif: failed to find mxc display driver
  135. Console: switching to colour frame buffer device 60x34
  136. mxsfb 21c8000.lcdif: initialized
  137. imx-sdma 20ec000.sdma: no event needs to be remapped
  138. imx-sdma 20ec000.sdma: loaded firmware 3.3
  139. imx-sdma 20ec000.sdma: initialized
  140. 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX
  141. console [ttymxc0] enabled
  142. 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 226, base_baud = 5000000) is a IMX
  143. 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 227, base_baud = 5000000) is a IMX
  144. imx-rng 2284000.rngb: iMX RNG Registered.
  145. imx sema4 driver is registered.
  146. [drm] Initialized drm 1.1.0 20060810
  147. [drm] Initialized vivante 1.0.0 20120216 on minor 0
  148. brd: module loaded
  149. loop: module loaded
  150. CAN device driver interface
  151. 2188000.ethernet supply phy not found, using dummy regulator
  152. pps pps0: new PPS source ptp0
  153. fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
  154. fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 1a:e7:44:b4:fa:22
  155. libphy: fec_enet_mii_bus: probed
  156. fec 2188000.ethernet eth0: registered PHC device 0
  157. PPP generic driver version 2.4.2
  158. PPP BSD Compression module registered
  159. PPP Deflate Compression module registered
  160. PPP MPPE Compression module registered
  161. NET: Registered protocol family 24
  162. SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
  163. CSLIP: code copyright 1989 Regents of the University of California.
  164. SLIP linefill/keepalive option.
  165. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  166. ehci-mxc: Freescale On-Chip EHCI Host driver
  167. usbcore: registered new interface driver cdc_acm
  168. cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  169. usbcore: registered new interface driver usb-storage
  170. usbcore: registered new interface driver usb_ehset_test
  171. 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
  172. 2184200.usb supply vbus not found, using dummy regulator
  173. ci_hdrc ci_hdrc.1: EHCI Host Controller
  174. ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
  175. ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
  176. hub 1-0:1.0: USB hub found
  177. hub 1-0:1.0: 1 port detected
  178. mousedev: PS/2 mouse device common for all mice
  179. input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
  180. tp reset gpio=131
  181. msg ft5x0x_i2c_rxdata i2c read error: -5
  182. ft5x0x read ID error!
  183. ft5x06_ts: probe of 1-0038 failed with error 161
  184. ft5x0x_ts_init successful
  185. input: iMX6UL TouchScreen Controller as /devices/platform/soc/2000000.aips-bus/2040000.tsc/input/input1
  186. snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
  187. i2c /dev entries driver
  188. IR NEC protocol handler initialized
  189. IR RC5(x/sz) protocol handler initialized
  190. IR RC6 protocol handler initialized
  191. IR JVC protocol handler initialized
  192. IR Sony protocol handler initialized
  193. IR SANYO protocol handler initialized
  194. IR Sharp protocol handler initialized
  195. IR MCE Keyboard/mouse protocol handler initialized
  196. IR XMP protocol handler initialized
  197. pxp-v4l2 pxp_v4l2: initialized
  198. usbcore: registered new interface driver uvcvideo
  199. USB Video Class driver (1.1.1)
  200. imx2-wdt 20bc000.wdog: use WDOG_B to reboot.
  201. imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
  202. Bluetooth: HCI UART driver ver 2.3
  203. Bluetooth: HCI UART protocol H4 registered
  204. Bluetooth: HCI UART protocol BCSP registered
  205. Bluetooth: HCI UART protocol ATH3K registered
  206. usbcore: registered new interface driver btusb
  207. usbcore: registered new interface driver ath3k
  208. sdhci: Secure Digital Host Controller Interface driver
  209. sdhci: Copyright(c) Pierre Ossman
  210. sdhci-pltfm: SDHCI platform and OF driver helper
  211. /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
  212. sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
  213. sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
  214. sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found
  215. sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
  216. mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
  217. usbcore: registered new interface driver usbhid
  218. usbhid: USB HID core driver
  219. usbcore: registered new interface driver snd-usb-audio
  220. fsl-asrc 2034000.asrc: driver registered
  221. NET: Registered protocol family 26
  222. mmc0: host does not support reading read-only switch, assuming write-enable
  223. usb 1-1: new high-speed USB device number 2 using ci_hdrc
  224. NET: Registered protocol family 10
  225. sit: IPv6 over IPv4 tunneling driver
  226. mmc0: new high speed SDHC card at address aaaa
  227. NET: Registered protocol family 17
  228. mmcblk0: mmc0:aaaa SL16G 14.8 GiB
  229. can: controller area network core (rev 20120528 abi 9)
  230. NET: Registered protocol family 29
  231.  mmcblk0: p1 p2
  232. can: raw protocol (rev 20120528)
  233. can: broadcast manager protocol (rev 20120528 t)
  234. can: netlink gateway (rev 20130117) max_hops=1
  235. Bluetooth: RFCOMM TTY layer initialized
  236. Bluetooth: RFCOMM socket layer initialized
  237. Bluetooth: RFCOMM ver 1.11
  238. Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  239. Bluetooth: BNEP filters: protocol multicast
  240. Bluetooth: BNEP socket layer initialized
  241. Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  242. Bluetooth: HIDP socket layer initialized
  243. 8021q: 802.1Q VLAN Support v1.8
  244. Key type dns_resolver registered
  245. dhd_module_init in
  246. snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 2019-05-31 05:57:49 UTC (1559282269)
  247. hub 1-1:1.0: USB hub found
  248. gpio_dvfs: disabling
  249. VSD_3V3: disabling
  250. hub 1-1:1.0: 2 ports detected
  251. can-3v3: disabling
  252. ALSA device list:
  253.   No soundcards found.
  254. EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (2c0)
  255. EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (2c0)
  256. EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
  257. VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
  258. devtmpfs: mounted
  259. Freeing unused kernel memory: 428K (80b39000 - 80ba4000)
  260. EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
  261. usb 1-1.1: new high-speed USB device number 3 using ci_hdrc
  262. devpts: called with bogus options
  263. random: dd urandom read with 9 bits of entropy available
  264. fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
  265. IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  266. fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
  267. IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  268. random: nonblocking pool is initialized
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!
 
Top