Guest User

WNDR3700v5 boot process

a guest
Apr 10th, 2015
1,877
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. ===================================================================
  2. MT7621 stage1 code 13:14:00 (ASIC)
  3. CPU=50000000 HZ BUS=16666666 HZ
  4. ==================================================================
  5. Change MPLL source from XTAL to CR...
  6. do MEMPLL setting..
  7. MEMPLL Config : 0x11100000
  8. 3PLL mode + External loopback
  9. === XTAL-40Mhz === DDR-1200Mhz ===
  10. PLL4 FB_DL: 0x10, 1/0 = 657/367 41000000
  11. PLL2 FB_DL: 0x16, 1/0 = 585/439 59000000
  12. PLL3 FB_DL: 0x16, 1/0 = 678/346 59000000
  13. do DDR setting..[00320000]
  14. Apply DDR3 Setting...(use customer AC)
  15. 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
  16. --------------------------------------------------------------------------------
  17. 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  18. 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  19. 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  20. 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  21. 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  22. 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  23. 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  24. 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  25. 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  26. 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  27. 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  28. 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  29. 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  30. 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
  31. 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1
  32. 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0
  33. 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0
  34. 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
  35. 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  36. 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  37. 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  38. 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  39. 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  40. 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  41. 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  42. 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  43. 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  44. 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  45. 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  46. 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  47. 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  48. 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  49. rank 0 coarse = 15
  50. rank 0 fine = 72
  51. B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0
  52. opt_dle value:9
  53. DRAMC_R0DELDLY[018]=00001F1F
  54. ==================================================================
  55. RX DQS perbit delay software calibration
  56. ==================================================================
  57. 1.0-15 bit dq delay value
  58. ==================================================================
  59. bit| 0 1 2 3 4 5 6 7 8 9
  60. --------------------------------------
  61. 0 | 13 10 14 13 14 11 15 9 6 11
  62. 10 | 9 13 10 14 9 13
  63. --------------------------------------
  64.  
  65. ==================================================================
  66. 2.dqs window
  67. x=pass dqs delay value (min~max)center
  68. y=0-7bit DQ of every group
  69. input delay:DQS0 =31 DQS1 = 31
  70. ==================================================================
  71. bit DQS0 bit DQS1
  72. 0 (1~60)30 8 (1~58)29
  73. 1 (1~58)29 9 (1~57)29
  74. 2 (1~60)30 10 (1~60)30
  75. 3 (1~58)29 11 (1~56)28
  76. 4 (1~60)30 12 (1~58)29
  77. 5 (2~60)31 13 (1~57)29
  78. 6 (1~61)31 14 (1~61)31
  79. 7 (1~60)30 15 (1~59)30
  80. ==================================================================
  81. 3.dq delay value last
  82. ==================================================================
  83. bit| 0 1 2 3 4 5 6 7 8 9
  84. --------------------------------------
  85. 0 | 14 12 15 15 15 11 15 10 8 13
  86. 10 | 10 15 12 15 9 14
  87. ==================================================================
  88. ==================================================================
  89. TX perbyte calibration
  90. ==================================================================
  91. DQS loop = 15, cmp_err_1 = ffff0800
  92. dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
  93. DQS loop = 14, cmp_err_1 = ffff0000
  94. dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2
  95. DQ loop=15, cmp_err_1 = ffff01a2
  96. DQ loop=14, cmp_err_1 = ffff0180
  97. DQ loop=13, cmp_err_1 = ffff0000
  98. dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=1
  99. dqs_perbyte_dly.last_dqdly_pass[1]=13, finish count=2
  100. byte:0, (DQS,DQ)=(9,8)
  101. byte:1, (DQS,DQ)=(8,8)
  102. 20,data:89
  103. [EMI] DRAMC calibration passed
  104.  
  105. ===================================================================
  106. MT7621 stage1 code done
  107. CPU=50000000 HZ BUS=16666666 HZ
  108. ===================================================================
  109.  
  110.  
  111. U-Boot 1.1.3 (Nov 17 2014 - 08:29:53)
  112.  
  113. Board: Ralink APSoC DRAM: 128 MB
  114. relocate_code Pointer at: 87fb4000
  115.  
  116. Config XHCI 40M PLL
  117. flash manufacture id: c2, device id 20 18
  118. find flash: MX25L12805D
  119. *** Warning - bad CRC, using default environment
  120.  
  121. ============================================
  122. Ralink UBoot Version: 4.2.1.0
  123. --------------------------------------------
  124. ASIC MT7621AS (MAC to MT7530 Mode)
  125. DRAM_CONF_FROM: Auto-Detection
  126. DRAM_TYPE: DDR3
  127. DRAM bus: 16 bit
  128. Xtal Mode=3 OCP Ratio=1/3
  129. Flash component: SPI Flash
  130. Date:Nov 17 2014 Time:08:29:53
  131. ============================================
  132. icache: sets:256, ways:4, linesz:32 ,total:32768
  133. dcache: sets:256, ways:4, linesz:32 ,total:32768
  134.  
  135. ##### The CPU freq = 880 MHZ ####
  136. estimate memory size =128 Mbytes
  137.  
  138. Reset switch ...
  139. #Reset_MT7530
  140. set LAN/WAN LLLLW
  141. Example expects ABI version 2
  142. Actual U-Boot ABI version 2
  143.  
  144. ******************************************
  145. Uboot StandAlone Entry
  146. ******************************************
  147. 0, cmd
  148. 1, 0x0000000D
  149. cmd : 0x0000000D
  150.  
  151.  
  152. Press Ctrl+C to Enter the Main loop...
  153. Example expects ABI version 2
  154. Actual U-Boot ABI version 2
  155.  
  156. ******************************************
  157. Uboot StandAlone Entry
  158. ******************************************
  159. 0, cmd
  160. 1, 0x0000000F
  161. cmd : 0x0000000F
  162. Enter NMRP_main
  163. Flash Sector Number : 256.
  164.  
  165. NetTxPacket = 0x87FE4300
  166.  
  167. KSEG1ADDR(NetTxPacket) = 0xA7FE4300
  168.  
  169. NetLoop,call eth_halt !
  170.  
  171. NetLoop,call eth_init !
  172. Trying Eth0 (10/100-M)
  173.  
  174. Waitting for RX_DMA_BUSY status Start... done
  175.  
  176.  
  177. ETH_STATE_ACTIVE!!
  178. NMRP_FLASH_SIZE_buffer --> a1000000.
  179. NMRP:LISTENING
  180. ### No NMRP Server found ###
  181. Example expects ABI version 2
  182. Actual U-Boot ABI version 2
  183.  
  184. ******************************************
  185. Uboot StandAlone Entry
  186. ******************************************
  187. 0, boot
  188. Flash Sector Number : 256.
  189.  
  190. ***************************************************
  191. Sercomm Boot Version 1.13.0
  192.  
  193. ***************************************************
  194. Entering Firmware : Everything is OK.
  195.  
  196. flash base: 0xbfc00000, kernel addr :0xbfc50000, bootloader size: 0x30000, config size 0x10000, fac size : 0x10000
  197. kernel addr :0xbfc50000
  198.  
  199. System Boot system code via Flash.
  200. ## Booting image at bfc50000 ...
  201. Image Name: Linux Kernel Image
  202. Image Type: MIPS Linux Kernel Image (lzma compressed)
  203. Data Size: 2404943 Bytes = 2.3 MB
  204. Load Address: 80001000
  205. Entry Point: 8000f500
  206. Verifying Checksum ... OK
  207. Uncompressing Kernel Image ... OK
  208.  
  209.  
  210.  
  211. commandline in boot is : <NULL> !!!!
  212.  
  213.  
  214.  
  215. No initrd
  216. ## Transferring control to Linux (at address 8000f500) ...
  217. ## Giving linux memsize in MB, 128
  218.  
  219. Starting kernel ...
  220.  
  221.  
  222. LINUX started...
  223.  
  224. THIS IS ASIC
  225. Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Nov 18 18:47:38 CST 2014
  226.  
  227. The CPU feqenuce set to 880 MHz
  228. GCMP present
  229. CPU revision is: 0001992f (MIPS 1004Kc)
  230. Software DMA cache coherency
  231. Determined physical RAM map:
  232. memory: 08000000 @ 00000000 (usable)
  233. Zone PFN ranges:
  234. Normal 0x00000000 -> 0x00008000
  235. Movable zone start PFN for each node
  236. early_node_map[1] active PFN ranges
  237. 0: 0x00000000 -> 0x00008000
  238. avail: cpu2 is not ready
  239. avail: cpu3 is not ready
  240. Detected 1 available secondary CPU(s)
  241. PERCPU: Embedded 7 pages/cpu @81103000 s7104 r8192 d13376 u65536
  242. pcpu-alloc: s7104 r8192 d13376 u65536 alloc=16*4096
  243. pcpu-alloc: [0] 0 [0] 1
  244. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  245. Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 console=ttyS0
  246. PID hash table entries: 512 (order: -1, 2048 bytes)
  247. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  248. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  249. Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
  250. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  251. MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  252. Writing ErrCtl register=00049021
  253. Readback ErrCtl register=00049021
  254. Memory: 122600k/131072k available (5108k kernel code, 8472k reserved, 1643k data, 212k init, 0k highmem)
  255. Hierarchical RCU implementation.
  256. Verbose stalled-CPUs detection is disabled.
  257. NR_IRQS:128
  258. Trying to install interrupt handler for IRQ24
  259. Trying to install interrupt handler for IRQ25
  260. Trying to install interrupt handler for IRQ22
  261. Trying to install interrupt handler for IRQ9
  262. Trying to install interrupt handler for IRQ10
  263. Trying to install interrupt handler for IRQ11
  264. Trying to install interrupt handler for IRQ12
  265. Trying to install interrupt handler for IRQ13
  266. Trying to install interrupt handler for IRQ14
  267. Trying to install interrupt handler for IRQ16
  268. Trying to install interrupt handler for IRQ17
  269. Trying to install interrupt handler for IRQ18
  270. Trying to install interrupt handler for IRQ19
  271. Trying to install interrupt handler for IRQ20
  272. Trying to install interrupt handler for IRQ21
  273. Trying to install interrupt handler for IRQ23
  274. Trying to install interrupt handler for IRQ26
  275. Trying to install interrupt handler for IRQ27
  276. Trying to install interrupt handler for IRQ28
  277. Trying to install interrupt handler for IRQ15
  278. Trying to install interrupt handler for IRQ8
  279. Trying to install interrupt handler for IRQ29
  280. Trying to install interrupt handler for IRQ30
  281. Trying to install interrupt handler for IRQ31
  282. console [ttyS1] enabled
  283. Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168)
  284. pid_max: default: 32768 minimum: 301
  285. Mount-cache hash table entries: 512
  286. launch: starting cpu1
  287. launch: cpu1 gone!
  288. CPU revision is: 0001992f (MIPS 1004Kc)
  289. Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
  290. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  291. MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  292. Brought up 2 CPUs
  293. Synchronize counters across 2 CPUs: done.
  294. NET: Registered protocol family 16
  295. release PCIe RST: RALINK_RSTCTRL = 7000000
  296. PCIE PHY initialize
  297. ***** Xtal 40MHz *****
  298. start MT7621 PCIe register access
  299. RALINK_RSTCTRL = 7000000
  300. RALINK_CLKCFG1 = 77ffeff8
  301.  
  302. *************** MT7621 PCIe RC mode *************
  303. PCIE1 no card, disable it(RST&CLK)
  304. pcie_link status = 0x5
  305. RALINK_RSTCTRL= 5000000
  306. *** Configure Device number setting of Virtual PCI-PCI bridge ***
  307. RALINK_PCI_PCICFG_ADDR = 21007f2 -> 12007f2
  308. PCIE0 enabled
  309. PCIE2 enabled
  310. interrupt enable status: 500000
  311. Port 1 N_FTS = 1b105000
  312. Port 0 N_FTS = 1b105000
  313. config reg done
  314. init_rt2880pci done
  315. bio: create slab <bio-0> at 0
  316. vgaarb: loaded
  317. SCSI subsystem initialized
  318. usbcore: registered new interface driver usbfs
  319. usbcore: registered new interface driver hub
  320. usbcore: registered new device driver usb
  321. pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
  322. pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
  323. pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
  324. pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
  325. pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
  326. pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
  327. pci 0000:00:00.0: BAR 1: set to [mem 0x60300000-0x6030ffff] (PCI address [0x60300000-0x6030ffff]
  328. pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
  329. pci 0000:00:01.0: BAR 1: set to [mem 0x60310000-0x6031ffff] (PCI address [0x60310000-0x6031ffff]
  330. pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
  331. pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff]
  332. pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
  333. pci 0000:00:00.0: PCI bridge to [bus 01-01]
  334. pci 0000:00:00.0: bridge window [io disabled]
  335. pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
  336. pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
  337. pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
  338. pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff] (PCI address [0x60200000-0x602fffff]
  339. pci 0000:00:01.0: PCI bridge to [bus 02-02]
  340. pci 0000:00:01.0: bridge window [io disabled]
  341. pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
  342. pci 0000:00:01.0: bridge window [mem pref disabled]
  343. PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
  344. PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
  345. BAR0 at slot 0 = 0
  346. bus=0x0, slot = 0x0
  347. res[0]->start = 0
  348. res[0]->end = 0
  349. res[1]->start = 60300000
  350. res[1]->end = 6030ffff
  351. res[2]->start = 0
  352. res[2]->end = 0
  353. res[3]->start = 0
  354. res[3]->end = 0
  355. res[4]->start = 0
  356. res[4]->end = 0
  357. res[5]->start = 0
  358. res[5]->end = 0
  359. BAR0 at slot 1 = 0
  360. bus=0x0, slot = 0x1
  361. res[0]->start = 0
  362. res[0]->end = 0
  363. res[1]->start = 60310000
  364. res[1]->end = 6031ffff
  365. res[2]->start = 0
  366. res[2]->end = 0
  367. res[3]->start = 0
  368. res[3]->end = 0
  369. res[4]->start = 0
  370. res[4]->end = 0
  371. res[5]->start = 0
  372. res[5]->end = 0
  373. bus=0x1, slot = 0x0, irq=0x4
  374. res[0]->start = 60000000
  375. res[0]->end = 600fffff
  376. res[1]->start = 0
  377. res[1]->end = 0
  378. res[2]->start = 0
  379. res[2]->end = 0
  380. res[3]->start = 0
  381. res[3]->end = 0
  382. res[4]->start = 0
  383. res[4]->end = 0
  384. res[5]->start = 0
  385. res[5]->end = 0
  386. bus=0x2, slot = 0x1, irq=0x19
  387. res[0]->start = 60200000
  388. res[0]->end = 602fffff
  389. res[1]->start = 0
  390. res[1]->end = 0
  391. res[2]->start = 0
  392. res[2]->end = 0
  393. res[3]->start = 0
  394. res[3]->end = 0
  395. res[4]->start = 0
  396. res[4]->end = 0
  397. res[5]->start = 0
  398. res[5]->end = 0
  399. Switching to clocksource MIPS
  400. NET: Registered protocol family 2
  401. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  402. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  403. TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  404. TCP: Hash tables configured (established 4096 bind 4096)
  405. TCP reno registered
  406. UDP hash table entries: 128 (order: 0, 4096 bytes)
  407. UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
  408. NET: Registered protocol family 1
  409. 4 CPUs re-calibrate udelay(lpj = 1167360)
  410. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  411. fuse init (API version 7.15)
  412. SGI XFS with security attributes, large block/inode numbers, no debug enabled
  413. SGI XFS Quota Management subsystem
  414. msgmni has been set to 239
  415. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
  416. io scheduler noop registered (default)
  417. Ralink gpio driver initialized
  418. spidrv_major = 217
  419. i2cdrv_major = 218
  420. spdif_mod_init: start SPDIF module
  421. Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  422. serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
  423. serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
  424. brd: module loaded
  425. flash manufacture id: c2, device id 20 18
  426. MX25L12805D(c2 2018c220) (16384 Kbytes)
  427. mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
  428. Creating 20 MTD partitions on "raspi":
  429. 0x000000000000-0x000000040000 : "Bootloader"
  430. 0x000000040000-0x000000050000 : "SC PID"
  431. 0x000000050000-0x0000002d0000 : "Kernel"
  432. 0x0000002d0000-0x000000e70000 : "Rootfs"
  433. 0x000000e70000-0x000000e90000 : "English UI"
  434. 0x000000e90000-0x000000eb0000 : "ML1"
  435. 0x000000eb0000-0x000000ed0000 : "ML2"
  436. 0x000000ed0000-0x000000ef0000 : "ML3"
  437. 0x000000ef0000-0x000000f10000 : "ML4"
  438. 0x000000f10000-0x000000f30000 : "ML5"
  439. 0x000000f30000-0x000000f40000 : "Factory"
  440. 0x000000f40000-0x000000f50000 : "SC Private Data"
  441. 0x000000f50000-0x000000f60000 : "POT"
  442. 0x000000f60000-0x000000f80000 : "Traffic Meter"
  443. 0x000000f80000-0x000000f90000 : "DPF"
  444. 0x000000f90000-0x000000fa0000 : "SC Nvram"
  445. 0x000000fa0000-0x000000fb0000 : "Ralink Nvram"
  446. 0x000000fb0000-0x000000fd0000 : "Ralink Reserved"
  447. 0x000000fd0000-0x000000ff0000 : "ML6"
  448. 0x000000ff0000-0x000001000000 : "Upgrade Flag"
  449. rdm_major = 253
  450. GMAC1_MAC_ADRH -- : 0x0000000c
  451. GMAC1_MAC_ADRL -- : 0x43288021
  452. Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
  453. GMAC1_MAC_ADRH -- : 0x0000000c
  454. GMAC1_MAC_ADRL -- : 0x43288028
  455. PROC INIT OK!
  456. PPP generic driver version 2.4.2
  457. PPP MPPE Compression module registered
  458. NET: Registered protocol family 24
  459. PPTP driver version 0.8.5
  460. IMQ driver loaded successfully.
  461. Hooking IMQ before NAT on PREROUTING.
  462. Hooking IMQ after NAT on POSTROUTING.
  463. usbcore: registered new interface driver net1080
  464. register mt_drv
  465.  
  466.  
  467. === pAd = c0182000, size = 586072 ===
  468.  
  469. <-- RTMPAllocTxRxRingMemory, Status=0
  470. <-- RTMPAllocAdapterBlock, Status=0
  471. pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
  472. device_id =0x7603
  473. RtmpChipOpsHook(502): Not support for HIF_MT yet!
  474. mt7603_init()-->
  475. mt_bcn_buf_init(224): Not support for HIF_MT yet!
  476. <--mt7603_init()
  477. FM_OUT value: u4FmOut = 0(0x00000000)
  478. FM_OUT value: u4FmOut = 0(0x00000000)
  479. FM_OUT value: u4FmOut = 0(0x00000000)
  480. FM_OUT value: u4FmOut = 0(0x00000000)
  481. FM_OUT value: u4FmOut = 0(0x00000000)
  482. FM_OUT value: u4FmOut = 0(0x00000000)
  483. FM_OUT value: u4FmOut = 0(0x00000000)
  484. FM_OUT value: u4FmOut = 0(0x00000000)
  485. FM_OUT value: u4FmOut = 0(0x00000000)
  486. FM_OUT value: u4FmOut = 0(0x00000000)
  487. FM_OUT value: u4FmOut = 0(0x00000000)
  488. FM_OUT value: u4FmOut = 0(0x00000000)
  489. FM_OUT value: u4FmOut = 0(0x00000000)
  490. FM_OUT value: u4FmOut = 0(0x00000000)
  491. FM_OUT value: u4FmOut = 0(0x00000000)
  492. FM_OUT value: u4FmOut = 0(0x00000000)
  493. FM_OUT value: u4FmOut = 0(0x00000000)
  494. FM_OUT value: u4FmOut = 0(0x00000000)
  495. FM_OUT value: u4FmOut = 0(0x00000000)
  496. FM_OUT value: u4FmOut = 0(0x00000000)
  497. xhc_mtk xhc_mtk: xHCI Host Controller
  498. xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
  499. xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
  500. hub 1-0:1.0: USB hub found
  501. hub 1-0:1.0: 2 ports detected
  502. xhc_mtk xhc_mtk: xHCI Host Controller
  503. xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
  504. hub 2-0:1.0: USB hub found
  505. hub 2-0:1.0: 1 port detected
  506. Netfilter messages via NETLINK v0.30.
  507. nf_conntrack version 0.5.0 (1915 buckets, 7660 max)
  508. nf_conntrack_rtsp v0.6.21 loading
  509. IPVS: Registered protocols ()
  510. IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
  511. IPVS: ipvs loaded.
  512. GRE over IPv4 demultiplexor driver
  513. gre: can't add protocol
  514. nf_nat_rtsp v0.6.21 loading
  515. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
  516. TCP cubic registered
  517. NET: Registered protocol family 10
  518. NOTIFY
  519. NOTIFY
  520. NOTIFY
  521. NOTIFY
  522. NOTIFY
  523. ip6_tables: (C) 2000-2006 Netfilter Core Team
  524. IPv6 over IPv4 tunneling driver
  525. NOTIFY
  526. NOTIFY
  527. NOTIFY
  528. NOTIFY
  529. NET: Registered protocol family 17
  530. L2TP core driver, V2.0
  531. PPPoL2TP kernel driver, V2.0
  532. L2TP IP encapsulation support (L2TPv3)
  533. L2TP netlink interface
  534. L2TP ethernet pseudowire support (L2TPv3)
  535. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  536. All bugs added by David S. Miller <davem@redhat.com>
  537. VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
  538. Freeing unused kernel memory: 212k freed
  539. init started: BusyBox v1.12.1 (2014-11-18 18:59:14 CST)
  540. starting pid 58, tty '': '/usr/etc/rcS'
  541. Algorithmics/MIPS FPU Emulator v1.5
  542. mount: mounting none on /dev/pts failed: No such file or directory
  543. Welcome to
  544. _______ _______ ___ __ ____ _ _ ___
  545. | ___ \| __ || | |__|| \ | || | / /
  546. | |___| || |__| || |__ __ | \| || |/ /
  547. | _ /| _ || || || |\ || \
  548. |__| \__\|__| |__||______||__||_| \____||_|\___\
  549.  
  550. =System Architecture Department=
  551.  
  552. [rc debug]/sbin/rc reg_init
  553. [rc.c::configure_mt7621_register():1011] set from jtag to gpio mode
  554. [SYSTEM]/sbin/reg s 0
  555. switch register base addr to system register 0xbe000000
  556. [SYSTEM]/sbin/reg r0x405a9
  557. 0x60
  558. [SYSTEM]/sbin/reg write offset 0x60, value 0x405a8
  559. w 0x60 0x405a8
  560. [SYSTEM]/sb0x405a8
  561. in/reg r 0x60
  562. [SYSTEM]/bin/echo 1 > /NOTIFY
  563. prNOTIFY
  564. ocNOTIFY
  565. /NOTIFY
  566. sNOTIFY
  567. ysNOTIFY
  568. /NOTIFY
  569. net/ipv6/conf/all/disable_ipv6
  570. led_pb_api: module license 'Sercomm' taints kernel.
  571. Disabling lock debugging due to kernel taint
  572. Register LED ID <75>
  573. Register LED ID <70>
  574. Register LED ID <20>
  575. Register LED ID <40>
  576. Register LED ID <45>
  577. Register LED ID <60>
  578. Register LED ID <61>
  579. Register LED ID <62>
  580. Register LED ID <90>
  581. Register LED ID <91>
  582. Register LED ID <92>
  583. insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko': No such file or directory
  584. insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/ext4/ext4.ko': No such file or directory
  585. netfilter dnshj choose interested dns queries module loaded !
  586. insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory
  587. init common module successful
  588. insert firewall block module success
  589. fake source dos protect modules is inserted
  590. netfilter PSD and TCP/UDP Echo/Chargen Attack loaded
  591. netfilter tcp syn flood module loaded
  592. netfilter clamp total session for one src ip module loaded
  593. netfilter other dos module loaded
  594. insmod finish
  595. NOTIFY
  596. NOTIFY
  597. NOTIFY
  598. Raeth v3.1 (Tasklet,SkbRecycle)
  599.  
  600. phy_tx_ring = 0x06de8000, tx_ring = 0xa6de8000
  601.  
  602. phy_rx_ring0 = 0x06dea000, rx_ring0 = 0xa6dea000
  603. change HW-TRAP to 0x15c8f
  604. set LAN/WAN LLLLW
  605. GMAC1_MAC_ADRH -- : 0x0000000c
  606. GMAC1_MAC_ADRL -- : 0x43288028
  607. GDMA2_MAC_ADRH -- : 0x0000000c
  608. GDMA2_MAC_ADRL -- : 0x43288045
  609. NOTIFY
  610. NOTIFY
  611. eth3: ===> VirtualIF_open
  612. CDMA_CSG_CFG = 81000000
  613. GDMA1_FWD_CFG = 20710000
  614. GDMA2_FWD_CFG = 20710000
  615. NOTIFY
  616. NOTIFY
  617. NOTIFY
  618. insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko': No such file or directory
  619. register rt2860
  620.  
  621.  
  622. === pAd = c0902000, size = 1348584 ===
  623.  
  624. <-- RTMPAllocTxRxRingMemory, Status=0
  625. <-- RTMPAllocAdapterBlock, Status=0
  626. pAd->CSRBaseAddress =0xc0800000, csr_addr=0xc0800000!
  627. device_id =0x7662
  628. ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
  629. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
  630. RtmpEepromGetDefault::e2p_dafault=2
  631. NVM is FLASH mode
  632. NOTIFY
  633. NOTIFY
  634. [rc debug]/usr/sbin/rc init
  635. [SYSTEM]/sbin/ifconfig NOTIFY
  636. br0 NOTIFY
  637. doNOTIFY
  638. wn hw ether A4:2B:8C:58:FA:38 up
  639. [SYSTEM]/sbin/ifconfig eth2.1 down
  640. ifconfig: SIOCGIFFLAGS: No such device
  641. [SYSTEM]/sbinNOTIFY
  642. /ifconfig eth2.2 down
  643. ifconfig: ra2880stop()...SDone
  644. IOeth3: ===> VirtualIF_close
  645. CGIFFFree TX/RX Ring Memory!
  646. LAGS:NOTIFY
  647. No such device
  648. [SYSTEM]/sbin/ifconfig eth2 down
  649. [SYSTEM]/sbin/vconfig rem eth2.1
  650. vconfig: ioctl error for rem: No sucNOTIFY
  651. hRaeth v3.1 ( dTasklete,SkbRecyclev)
  652. ice
  653. phy_tx_ring = 0x06590000, tx_ring = 0xa6590000
  654.  
  655.  
  656. phy_rx_ring0 = 0x065ac000, rx_ring0 = 0xa65ac000
  657. [SYSTEM]/sbin/vconfig rem eth2.2
  658. vconfig: ioctl error for rem: Nochange HW-TRAP to 0x15c8f
  659. such deviceset LAN/WAN LLLLW
  660.  
  661. [SYSTEM]/sbiGMAC1_MAC_ADRH -- : 0x0000000c
  662. nGMAC1_MAC_ADRL -- : 0x43288028
  663. /ieth3: ===> VirtualIF_open
  664. fCDMA_CSG_CFG = 81000000
  665. cGDMA1_FWD_CFG = 20710000
  666. oGDMA2_FWD_CFG = 20710000
  667. nfigNOTIFY
  668. eth2 up
  669. [SYSTEM]/sbin/ifconfiNOTIFY
  670. g eth2 down
  671. ra2880stop()...Done
  672. eth3: ===> VirtualIF_close
  673. Free TX/RX Ring Memory!
  674. NOTIFY
  675. [SYSTEM]/sbin/ifconfig eNOTIFY
  676. NOTIFY ether A4:2B:8C:58:FA:38
  677.  
  678. Raeth v3.1 (asklet3,SkbRecycle2)
  679. m[S
  680. phy_tx_ring = 0x06590000, tx_ring = 0xa6590000
  681. YSTEM]/
  682. phy_rx_ring0 = 0x06594000, rx_ring0 = 0xa6594000
  683. sbin/ifconfig eth2 up
  684. change HW-TRAP to 0x15c8f
  685. set LAN/WAN LLLLW
  686. GMAC1_MAC_ADRH -- : 0x0000a42b
  687. GMAC1_MAC_ADRL -- : 0x8c58fa38
  688. eth3: ===> VirtualIF_open
  689. CDMA_CSG_CFG = 81000000
  690. GDMA1_FWD_CFG = 20710000
  691. GDMA2_FWD_CFG = 20710000
  692. NOTIFY
  693. [SYSTEM]/usr/sbin/config-vlan.sh 3 0
  694. restore GSW to dump switch mode
  695. switch reg write offset=2004, value=ff0000
  696. switch reg write offset=2104, value=ff0000
  697. switch reg write offset=2204, value=ff0000
  698. switch reg write offset=2304, value=ff0000
  699. switch reg write offset=2404, value=ff0000
  700. switch reg write offset=2504, value=ff0000
  701. device eth2 entered promiscuous modeff0000
  702.  
  703. sbr0: port 1(eth2) entering learning state
  704. wibr0: port 1(eth2) entering learning state
  705. tch reg write offset=2704, value=ffNOTIFY
  706. 0eth3: ===> VirtualIF_open
  707. 00NOTIFY
  708. 0
  709. switch reg write offset=2010, value=810000c0
  710. switch reg write offset=2110, value=810000c0
  711. switch reg write offset=2210, value=810000c0
  712. switch reg write offset=2310, value=810000c0
  713. switch reg write offset=2410, value=810000c0
  714. switch reg write offset=2510, value=810000c0
  715. switch reg write offset=2610, value=810000c0
  716. switch reg write offset=2710, value=810000c0
  717. REG_ESW_WT_MAC_ATC is 0x7ff0002
  718. done.
  719. [SYSTEM]/sbin/brctl addif br0 eth2
  720. [SYSTEM]/sbin/ifconfig eth3 up
  721. RC: wifi_init()
  722. rules = <>, timeout = 20
  723. [SYSTEM]/usr/bin/killall access_logd
  724. killall: access_logd: no process killed
  725. [SYSTEM]/usr/sbin/rc access_log start
  726. [rc debug]/usr/sbin/rc access_log start
  727. ap_name=access_log action=start
  728. [rc.c::rc_action():803] rc_action before add access_log - start
  729. rc action <access_log @ start> before file_lock.
  730. rc action <access_log @ start lock = 3> after file_lock.
  731. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
  732. rc action < unlock = 3> after file_lock.
  733. [rc.c::rc_action():811] rc_action after add access_log - start
  734. unlink running file </var/run/rc.access_log.run>
  735. [rc.c::rc_action():803] rc_action before add access_log - start
  736. rc action <access_log @ start> before file_lock.
  737. rc action <access_log @ start lock = 3> after file_lock.
  738. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
  739. rc action < unlock = 3> after file_lock.
  740. [rc.c::rc_action():811] rc_action after add access_log - start
  741. unlink running file </var/run/rc.access_log.run>
  742. can't find this application
  743. [rc.c::rc_action():803] rc_action before add access_log - start
  744. rc action <access_log @ start> before file_lock.
  745. rc action <access_log @ start lock = 3> after file_lock.
  746. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
  747. rc action < unlock = 3> after file_lock.
  748. [rc.c::rc_action():811] rc_action after add access_log - start
  749. [rc.c::rc_start():706] Calling Start function of access_log
  750. killall: access_logd: no process killed
  751. Access Control log start.
  752. Access Control socket create
  753. unlink running file </var/run/rc.access_log.run>
  754. [SYSTEM]/usr/sbin/rc access_dev start
  755. [rc debug]/usr/sbin/rc access_dev start
  756. ap_name=access_dev action=start
  757. [rc.c::rc_action():803] rc_action before add access_dev - start
  758. rc action <access_dev @ start> before file_lock.
  759. rc action <access_dev @ start lock = 3> after file_lock.
  760. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
  761. rc action < unlock = 3> after file_lock.
  762. [rc.c::rc_action():811] rc_action after add access_dev - start
  763. unlink running file </var/run/rc.access_dev.run>
  764. [rc.c::rc_action():803] rc_action before add access_dev - start
  765. rc action <access_dev @ start> before file_lock.
  766. rc action <access_dev @ start lock = 3> after file_lock.
  767. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
  768. rc action < unlock = 3> after file_lock.
  769. [rc.c::rc_action():811] rc_action after add access_dev - start
  770. unlink running file </var/run/rc.access_dev.run>
  771. can't find this application
  772. [rc.c::rc_action():803] rc_action before add access_dev - start
  773. rc action <access_dev @ start> before file_lock.
  774. rc action <access_dev @ start lock = 3> after file_lock.
  775. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
  776. rc action < unlock = 3> after file_lock.
  777. [rc.c::rc_action():811] rc_action after add access_dev - start
  778. [rc.c::rc_start():706] Calling Start function of access_dev
  779. killall: access_devinfo: no process killed
  780. Access Control socket create
  781. unlink running file </var/run/rc.access_dev.run>
  782. [modelinfo_product_id.c::modelinfo_map_index():74] 0x30 0x32, 0x3032.
  783. [modelinfo_product_id.c::modelinfo_map_index():118] find index 1 for modelinfo_get_product_name
  784. [modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():185] autoupg_fileinfo_in_nv is wndr3700v5_fileinfo.txt
  785. [SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko
  786. ufsd:: trace mask set to 0000000f
  787. ufsd: driver (lke_9.0.0 lke_9.0.0_r237695_b2, LBD=ON, ioctl, bdi, sd2(0), wb, bz, tr) loaded at c0b02000
  788. NTFS support included
  789. optimized: speed
  790. Build_for__Netgear_R6220_k2.6.36_2014-10-22_lke_9.0.0_r237695_b2
  791.  
  792. =============rc start
  793. [rc debug]/usr/sbin/rc lan start
  794. ap_name=lan action=start
  795. [rc.c::rc_action():803] rc_action before add lan - start
  796. rc action <lan @ start> before file_lock.
  797. rc action <lan @ start lock = 3> after file_lock.
  798. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run
  799. rc action < unlock = 3> after file_lock.
  800. [rc.c::rc_action():811] rc_action after add lan - start
  801. [rc.c::rc_start():706] Calling Start function of lan
  802. [SYSTEM]/usr/sbin/brctl setfd br0 1
  803. [SYSTEM]/sbin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255
  804. [SYSTEM]/usr/sbin/brctl stp br0 off
  805. [SYSTEM]/usr/sbin/brctl stp br0 off
  806. sh: cannot create /proc/http_file/getLanIp: nonexistent directory
  807. unlink running file </var/run/rc.lan.run>
  808. [rc debug]/usr/sbin/rc wlan start
  809. ap_name=wlan action=start
  810. [rc.c::rc_action():803] rc_action before add wlan - start
  811. rc action <wlan @ start> before file_lock.
  812. rc action <wlan @ start lock = 3> after file_lock.
  813. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
  814. rc action < unlock = 3> after file_lock.
  815. [rc.c::rc_action():811] rc_action after add wlan - start
  816. [rc.c::rc_start():706] Calling Start function of wlan
  817. [wifi_mtk/wifi.c::sync_wireless_nvram():1495] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100
  818. [modelinfo_product_id.c::modelinfo_map_index():74] 0x30 0x32, 0x3032.
  819. [modelinfo_product_id.c::modelinfo_map_index():118] find index 1 for modelinfo_get_product_name
  820. [wifi_mtk/wifi.c::start_wireless():1525] SC 5G support level: 11n
  821. [SYSTEM]mkdir -p /etc/Wireless/RT2860
  822. [flash.c::sc_check_remotescfgmgrmagic():794] buf:ff, ff, ff, ff
  823. [flash.c::sc_check_remotescfgmgrmagic():796] magic:31, 3e, c5, 8d
  824. scfgmgr for local
  825. [SYSTEM]mkdir -p /etc/Wireless/iNIC
  826. region flag in flash:00 00 00 02
  827. [SYSTEM]/bin/mkdir -p /etc/Wireless/RT2860AP/
  828. [SYSTEM]/bin/mkdir -p /etc_ro/Wireless/RT2860AP/
  829. region is PR:0
  830. [SYSTEM]/bin/cp -f /etc_ro/wlan/MT7612E_EEPROM.bin.11n /etc_ro/wlan/MT7612E_EEPROM.bin
  831. [wifi_mtk/wifi.c::map_singleskutmp_by_region():1251] all region singlesku.dat exist
  832. [SYSTEM]/bin/rm /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1
  833. rm: cannot remove '/etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620': No such file or directory
  834. [SYSTEM]/bin/rm /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1
  835. rm: cannot remove '/etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E': No such file or directory
  836. [wifi_mtk/wifi.c::map_singleskutmp_by_region():1268] wifi gui region is Europe, 2g CE, 5g CE
  837. [wifi_mtk/wifi.c::map_singleskutmp_by_region():1306] region NOT PR or RU
  838. [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-2.4.txt /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1
  839. [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-5G.txt /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1
  840. [SYSTEM]/bin/mv /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 /etc/Wireless/RT2860AP/SingleSKU.dat
  841. [SYSTEM]/bin/mv /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E /etc_ro/Wireless/iNIC/SingleSKU.dat
  842. CHIP: 7603 - current MAC: XX:XX:XX:XX:XX:XX
  843. Assign MAC: XX:XX:XX:XX:XX:XX
  844. no update!
  845. CHIP: 7662 - current MAC: XX:XX:XX:XX:XX:XX
  846. Assign MAC: XX:XX:XX:XX:XX:XX
  847. no update!
  848. [SYSTEM]/sbin/iwpriv rai0 set RadioOn=1
  849. Interface doesn't accept private ioctl...
  850. set (8BE2): Network is down
  851. [SYSTEM]echo 1 > /tmp/wifi_mac_setNOTIFY
  852.  
  853. X_BCN DESC a7f94000 size = 320
  854. [3RX[0] DESC a7f96000 size = 2048
  855. 2m[SYSTEM]/sbiRX[1] DESC a7f97000 size = 2048
  856. n/ifconfig ra0 up
  857. cfg_mode=9
  858. cfg_mode=9
  859. wmode_band_equal(): Band Equal!
  860. APSDCapable[0]=0
  861. APSDCapable[1]=0
  862. APSDCapable[2]=0
  863. APSDCapable[3]=0
  864. APSDCapable[4]=0
  865. APSDCapable[5]=0
  866. APSDCapable[6]=0
  867. APSDCapable[7]=0
  868. APSDCapable[8]=0
  869. APSDCapable[9]=0
  870. APSDCapable[10]=0
  871. APSDCapable[11]=0
  872. APSDCapable[12]=0
  873. APSDCapable[13]=0
  874. APSDCapable[14]=0
  875. APSDCapable[15]=0
  876. Key1Str is Invalid key length(0) or Type(0)
  877. Key1Str is Invalid key length(0) or Type(0)
  878. Key1Str is Invalid key length(0) or Type(0)
  879. Key1Str is Invalid key length(0) or Type(0)
  880. Key2Str is Invalid key length(0) or Type(0)
  881. Key2Str is Invalid key length(0) or Type(0)
  882. Key2Str is Invalid key length(0) or Type(0)
  883. Key2Str is Invalid key length(0) or Type(0)
  884. Key3Str is Invalid key length(0) or Type(0)
  885. Key3Str is Invalid key length(0) or Type(0)
  886. Key3Str is Invalid key length(0) or Type(0)
  887. Key3Str is Invalid key length(0) or Type(0)
  888. Key4Str is Invalid key length(0) or Type(0)
  889. Key4Str is Invalid key length(0) or Type(0)
  890. Key4Str is Invalid key length(0) or Type(0)
  891. Key4Str is Invalid key length(0) or Type(0)
  892. 20140814CmdAddressLenReq:(ret = 0)
  893. CmdFwStartReq: override = 1, address = 1048576
  894. CmdStartDLRsp: WiFI FW Download Success
  895. AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
  896. CmdPsRetrieveRsp Disable FW PS Supportstatus:1 !!!!!
  897. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
  898. efuse_probe: efuse = 10000002
  899. RtmpEepromGetDefault::e2p_dafault=1
  900. RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
  901. NVM is FLASH mode
  902. 1. Phy Mode = 14
  903. Country Region from e2p = ffff
  904. tssi_1_target_pwr_g_band = 35
  905. 2. Phy Mode = 14
  906. 3. Phy Mode = 14
  907. NICInitPwrPinCfg(13): Not support for HIF_MT yet!
  908. NICInitializeAsic(586): Not support rtmp_mac_sys_reset () for HIF_MT yet!
  909. mt_mac_init()-->
  910. mt7603_init_mac_cr()-->
  911. AsicSetMacMaxLen(1561): Set the Max RxPktLen=1024!
  912. <--mt_mac_init()
  913. WTBL Segment 1 info:
  914. MemBaseAddr/FID:0x28000/0
  915. EntrySize/Cnt:32/128
  916. WTBL Segment 2 info:
  917. MemBaseAddr/FID:0x40000/0
  918. EntrySize/Cnt:64/128
  919. WTBL Segment 3 info:
  920. MemBaseAddr/FID:0x42000/64
  921. EntrySize/Cnt:64/128
  922. WTBL Segment 4 info:
  923. MemBaseAddr/FID:0x44000/128
  924. EntrySize/Cnt:32/128
  925. AntCfgInit(2362): Not support for HIF_MT yet!
  926. AsicSendCommandToMcu(3410): Not support for HIF_MT yet!
  927. AsicSendCommandToMcu(3410): Not support for HIF_MT yet!
  928. AsicSendCommandToMcu(3410): Not support for HIF_MT yet!
  929. AsicSendCommandToMcu(3410): Not support for HIF_MT yet!
  930. RTMPSetPhyMode(): channel out of range, use first ch=0
  931. MCS Set = ff ff 00 00 01
  932. AsicSetChBusyStat(877): Not support for HIF_MT yet!
  933. CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2
  934. mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
  935. CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2
  936. mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
  937. CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2
  938. mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
  939. CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2
  940. mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
  941. CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2
  942. mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
  943. CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2
  944. mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
  945. CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2
  946. mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
  947. CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2
  948. mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
  949. CmdChannelSwitch: control_chl = 9, central_chl = 9, BW = 0, TXStream = 2, RXStream = 2
  950. mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0
  951. CmdChannelSwitch: control_chl = 10, central_chl = 10, BW = 0, TXStream = 2, RXStream = 2
  952. mt7603_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0
  953. CmdChannelSwitch: control_chl = 11, central_chl = 11, BW = 0, TXStream = 2, RXStream = 2
  954. mt7603_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0
  955. CmdChannelSwitch: control_chl = 12, central_chl = 12, BW = 0, TXStream = 2, RXStream = 2
  956. mt7603_switch_channel(): Switch to Ch#12(2T2R), BBP_BW=0
  957. CmdChannelSwitch: control_chl = 13, central_chl = 13, BW = 0, TXStream = 2, RXStream = 2
  958. mt7603_switch_channel(): Switch to Ch#13(2T2R), BBP_BW=0
  959. CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2
  960. mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
  961. SYNC - BBP R4 to 20MHz.l
  962. CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2
  963. mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
  964. SYNC - BBP R4 to 20MHz.l
  965. CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2
  966. mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
  967. SYNC - BBP R4 to 20MHz.l
  968. CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2
  969. mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
  970. SYNC - BBP R4 to 20MHz.l
  971. CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2
  972. mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
  973. SYNC - BBP R4 to 20MHz.l
  974. CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2
  975. mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
  976. SYNC - BBP R4 to 20MHz.l
  977. CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2
  978. mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
  979. SYNC - BBP R4 to 20MHz.l
  980. CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2
  981. mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
  982. SYNC - BBP R4 to 20MHz.l
  983. [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
  984. [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  985. [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
  986. [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
  987. [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
  988. AsicSetRalinkBurstMode(3724): Not support for HIF_MT yet!
  989. RTMPSetPiggyBack(797): Not support for HIF_MT yet!
  990. CmdChannelSwitch: control_chl = 1, central_chl = 3, BW = 1, TXStream = 2, RXStream = 2
  991. mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1
  992. AsicSetTxPreamble(3710): Not support for HIF_MT yet!
  993. AsicAddSharedKeyEntry(1725): Not support for HIF_MT yet!
  994. AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
  995. Main bssid = XX:XX:XX:XX:XX:XX
  996. <==== rt28xx_init, Status=0
  997. NOTIFY
  998. NOTIFY
  999. NOTIFY
  1000. NOTIFY
  1001. NOTIFY
  1002. NOTIFY
  1003. NOTIFY
  1004. NOTIFY
  1005. NOTIFY
  1006. NOTIFY
  1007. NOTIFY
  1008. NOTIFY
  1009. NOTIFY
  1010. NOTIFY
  1011. NOTIFY
  1012. [SYSTEM]/sbin/brctl addevice ra0 entered promiscuous mode
  1013. dibr0: port 2(ra0) entering learning state
  1014. f br0: port 2(ra0) entering learning state
  1015. br0 ra0
  1016. [SYSTEM]/bin/led_app on 40
  1017. [SYSTEM]/sbin/ifconfig rNOTIFY
  1018. aibuild time =
  1019. 02 0u1p4[400m8
  1020. 60640a
  1021. rom patch for E3 IC
  1022.  
  1023. platform =
  1024. ALPS
  1025. hw/sw version =
  1026. ŠŠ
  1027. patch version =
  1028.  
  1029. FW Version:0.0.00 Build:1
  1030. Build Time:201409051439____
  1031. fw for E3 IC
  1032. RX[0] DESC a6694000 size = 4096
  1033. RX[1] DESC a6695000 size = 4096
  1034. E2pAccessMode=2
  1035. cfg_mode=8
  1036. cfg_mode=8
  1037. wmode_band_equal(): Band Not Equal!
  1038. APSDCapable[0]=0
  1039. APSDCapable[1]=0
  1040. APSDCapable[2]=0
  1041. APSDCapable[3]=0
  1042. APSDCapable[4]=0
  1043. APSDCapable[5]=0
  1044. APSDCapable[6]=0
  1045. APSDCapable[7]=0
  1046. APSDCapable[8]=0
  1047. APSDCapable[9]=0
  1048. APSDCapable[10]=0
  1049. APSDCapable[11]=0
  1050. APSDCapable[12]=0
  1051. APSDCapable[13]=0
  1052. APSDCapable[14]=0
  1053. APSDCapable[15]=0
  1054. flush result = ffffff
  1055. check pse fid Q7:set_get_fid, q_idx:7 empty!!
  1056. Key1Str is Invalid key length(0) or Type(0)
  1057. Key1Str is Invalid key length(0) or Type(0)
  1058. Key1Str is Invalid key length(0) or Type(0)
  1059. Key1Str is Invalid key length(0) or Type(0)
  1060. Key2Str is Invalid key length(0) or Type(0)
  1061. Key2Str is Invalid key length(0) or Type(0)
  1062. Key2Str is Invalid key length(0) or Type(0)
  1063. Key2Str is Invalid key length(0) or Type(0)
  1064. Key3Str is Invalid key length(0) or Type(0)
  1065. Key3Str is Invalid key length(0) or Type(0)
  1066. Key3Str is Invalid key length(0) or Type(0)
  1067. Key3Str is Invalid key length(0) or Type(0)
  1068. Key4Str is Invalid key length(0) or Type(0)
  1069. Key4Str is Invalid key length(0) or Type(0)
  1070. Key4Str is Invalid key length(0) or Type(0)
  1071. Key4Str is Invalid key length(0) or Type(0)
  1072. 1. Phy Mode = 17
  1073. get_chl_grp:illegal channel (167)
  1074. get_chl_grp:illegal channel (167)
  1075. get_chl_grp:illegal channel (169)
  1076. get_chl_grp:illegal channel (169)
  1077. get_chl_grp:illegal channel (171)
  1078. get_chl_grp:illegal channel (171)
  1079. br0: port 2(ra0) entering forwarding state
  1080. get_chl_grp:illegal channel (173)
  1081. get_chl_grp:illegal channel (173)
  1082. Country Region from e2p = ffff
  1083. mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1
  1084. mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
  1085. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=13, low_temp_slope=9
  1086. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
  1087. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
  1088. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
  1089. mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
  1090. 2. Phy Mode = 17
  1091. 3. Phy Mode = 17
  1092. andes_pci_fw_init
  1093. 0x1300 = 00073200
  1094. AntCfgInit: primary/secondary ant 0/1
  1095. andes_load_cr:cr_type(2)
  1096. ChipStructAssign(): MT76x2 hook !
  1097. RTMPSetPhyMode: channel is out of range, use first channel=0
  1098. MCS Set = ff ff 00 00 01
  1099. mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe
  1100. mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a
  1101. mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe
  1102. mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a
  1103. mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe
  1104. mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a
  1105. br0: port 1(eth2) entering forwarding state
  1106. mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe
  1107. mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a
  1108. mt76x2_bbp_adjust():rf_bw=1, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=0
  1109. mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe
  1110. mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a
  1111. APStartUp(): AP Set CentralFreq at 38(Prim=40, HT-CentCh=38, VHT-CentCh=0, BBP_BW=1)
  1112. mt76x2_calibration(channel = 38)
  1113. Main bssid = XX:XX:XX:XX:XX:XX
  1114. mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
  1115. mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
  1116. mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
  1117. mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
  1118. original vga value(chain0) = 48
  1119. original vga value(chain1) = 48
  1120. <==== rt28xx_init, Status=0
  1121. NOTIFY
  1122. NOTIFY
  1123. NOTIFY
  1124. NOTIFY
  1125. NOTIFY
  1126. NOTIFY
  1127. NOTIFY
  1128. NOTIFY
  1129. NOTIFY
  1130. NOTIFY
  1131. NOTIFY
  1132. NOTIFY
  1133. NOTIFY
  1134. NOTIFY
  1135. RTMPDrvOpen(1):Check if PDMA is idle!
  1136. RTMPDrvOpen(2):Check if PDMA is idle!
  1137. NOTIFY
  1138. [SYSTEM]/sbin/brctl device rai0 entered promiscuous mode
  1139. addbr0: port 3(rai0) entering learning state
  1140. ibr0: port 3(rai0) entering learning state
  1141. f br0 rai0
  1142. [SYSTEM]/bin/led_app on 40
  1143. [libscm_wl.c::GenerateUUID():121]
  1144. GUI ASCII string: 38833092-3092-1883-b1b5-a42b8c58fa38
  1145. [libscm_wl.c::GenerateUUID():122]
  1146. GUI HEX string: 3883309230921883b1b5a42b8c58fa38
  1147. [SYSTEM]/usr/bin/killall miniupnpd_wsc
  1148. killall: miniupnpd_wsc: no process killed
  1149. [SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
  1150. [SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
  1151. + iwpriv ra0 set WscConfMode=0
  1152. + iwpriv rai0 set WscConfMode=0
  1153. + iwpriv ra0 set WscSetupLock=0
  1154. + iwpriv rai0 set WscSetupLock=0
  1155. + iwpriv ra0 set WscMaxPinAttack=3
  1156. + iwpriv rai0 set WscMaxPinAttack=3
  1157. + route add -host 239.255.255.250 dev br0
  1158. + iwpriv ra0 set WscConfMode=7
  1159. + iwpriv rai0 set WscConfMode=7
  1160. + miniupnpd_wsc -m 1 -I ra0 -P /var/Can't find DB for id==42
  1161. run/miniupnpd.ra0 -i eth3 -a 192.168.1.1 -n 7777 -u 38833092-3092-1883-b1b5-a42b8c58fa38
  1162. Unknown option: -I
  1163. Unknown option: ra0
  1164. Jan 1 00:00:26 miniupnpd[318]: WPS listening on port 7777
  1165. [SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptiRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fe88000)=60200618!
  1166. meRTMPIoctlMAC():after trim space, ptr len=8, pointer(86115000)=60200618!
  1167.  
  1168. [SYSTEM]/bin/led_app on 42
  1169. TMPIoctlMAC():wrq->u.data.length=18, pointer(7f9a36e0)=60200618=D7083F0F!
  1170. [3RTMPIoctlMAC():after trim space, ptr len=17, pointer(85daf000)=60200618=D7083F0F!
  1171. 2m[SYSTEM]/usr/sbin/led_app on 45
  1172. [wifi_mtk/wifi.c::start_wireless():1615] DISABLE EDCCA for 2G and 5G
  1173. [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340
  1174. rai0 mac:
  1175. [0x1340]:04101b3f
  1176. [wifi_mtk/wifi.c::start_wireless():1639] org:0x4101b3f. (04101b3f
  1177. )[wifi_mtk/wifi.c::start_wireless():1641] now:0x4001b3f
  1178. [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340=4001b3f
  1179. rai0 mac:
  1180. [0x1340]:04001b3f
  1181. [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340
  1182. rai0 mac:
  1183. [0x1340]:04001b3f
  1184. [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618
  1185. ra0 mac:[0x10618]:d7e87d10
  1186. [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618=D7083F0F
  1187. ra0 mac:[0x10618]:d7083f0f
  1188. unlink running file </var/run/rc.wlan.run>
  1189. [rc debug]/usr/sbin/rc printk start
  1190. ap_name=printk action=start
  1191. [rc.c::rc_action():803] rc_action before add printk - start
  1192. rc action <printk @ start> before file_lock.
  1193. rc action <printk @ start lock = 3> after file_lock.
  1194. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run
  1195. rc action < unlock = 3> after file_lock.
  1196. [rc.c::rc_action():811] rc_action after add printk - start
  1197. [rc.c::rc_start():706] Calling Start function of printk
  1198. [SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk
  1199. unlink running file </var/run/rc.printk.run>
  1200. [rc debug]/usr/sbin/rc timezone start
  1201. ap_name=timezone action=start
  1202. [rc.c::rc_action():803] rc_action before add timezone - start
  1203. rc action <timezone @ start> before file_lock.
  1204. rc action <timezone @ start lock = 3> after file_lock.
  1205. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run
  1206. rc action < unlock = 3> after file_lock.
  1207. [rc.c::rc_action():811] rc_action after add timezone - start
  1208. [rc.c::rc_start():706] Calling Start function of timezone
  1209. [SYSTEM]/bin/echo GMT+0 > /etc/TZ
  1210. unlink running file </var/run/rc.timezone.run>
  1211. [rc debug]/usr/sbin/rc syslogd start
  1212. ap_name=syslogd action=start
  1213. [rc.c::rc_action():803] rc_action before add syslogd - start
  1214. rc action <syslogd @ start> before file_lock.
  1215. rc action <syslogd @ start lock = 3> after file_lock.
  1216. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
  1217. rc action < unlock = 3> after file_lock.
  1218. [rc.c::rc_action():811] rc_action after add syslogd - start
  1219. [rc.c::rc_start():706] Calling Start function of syslogd
  1220. [SYSTEM]/sbin/syslogd -f /etc/syslog.conf
  1221. unlink running file </var/run/rc.syslogd.run>
  1222. [rc debug]/usr/sbin/rc httpd start
  1223. ap_name=httpd action=start
  1224. [rc.c::rc_action():803] rc_action before add httpd - start
  1225. rc action <httpd @ start> before file_lock.
  1226. rc action <httpd @ start lock = 3> after file_lock.
  1227. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
  1228. rc action < unlock = 3> after file_lock.
  1229. [rc.c::rc_action():811] rc_action after add httpd - start
  1230. [rc.c::rc_start():706] Calling Start function of httpd
  1231. [sc_language.c::create_language_file():426] Create link files for <French>
  1232. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU
  1233. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to DEU
  1234. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to FRA
  1235. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to NLD
  1236. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to SVE
  1237. [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to RUS
  1238. [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock6> according to its id <FRA>
  1239. [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock6>
  1240. [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WNDR3700v5|g" > /etc/block.htm
  1241. rmmod: ipt_REJECT: No such file or directory
  1242. [rc debug]/bin/rc firewall restart
  1243. ap_name=firewall action=restart
  1244. [rc.c::rc_action():803] rc_action before add firewall - restart
  1245. rc action <firewall @ restart> before file_lock.
  1246. rc action <firewall @ restart lock = 3> after file_lock.
  1247. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
  1248. rc action < unlock = 3> after file_lock.
  1249. [rc.c::rc_action():811] rc_action after add firewall - restart
  1250. unlink running file </var/run/rc.firewall.run>
  1251. [rc.c::rc_action():803] rc_action before add firewall - restart
  1252. rc action <firewall @ restart> before file_lock.
  1253. rc action <firewall @ restart lock = 3> after file_lock.
  1254. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
  1255. rc action < unlock = 3> after file_lock.
  1256. [rc.c::rc_action():811] rc_action after add firewall - restart
  1257. [rc.c::rc_stop():745] Calling Stop function of firewall
  1258. [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
  1259. [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
  1260. [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
  1261. sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
  1262. [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
  1263. sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
  1264. [rc.c::rc_start():706] Calling Start function of firewall
  1265. [SYSTEM]/usr/bin/killall -14 access_logd
  1266. [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
  1267. [rc debug]/usr/sbin/rc syslogd create
  1268. ap_name=syslogd action=create
  1269. [rc.c::rc_action():803] rc_action before add syslogd - create
  1270. rc action <syslogd @ create> before file_lock.
  1271. rc action <syslogd @ create lock = 4> after file_lock.
  1272. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
  1273. rc action < unlock = 4> after file_lock.
  1274. [rc.c::rc_action():811] rc_action after add syslogd - create
  1275. [rc.c::rc_create():787] Calling Create function of syslogd
  1276. unlink running file </var/run/rc.syslogd.run>
  1277. [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
  1278. [SYSTEM]/bin/echo clear > /proc/net/firewall_block
  1279. [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
  1280. [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
  1281. [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
  1282. [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable
  1283. [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
  1284. fw_pt
  1285. [SYSTEM]/usr/sbin/killall -9 usb_httpd
  1286. killall: usb_httpd: no process killed
  1287. [SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable
  1288. [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02
  1289. [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
  1290. [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1
  1291. [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02
  1292. [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
  1293. [SYSTEM]/bin/echo GMT+0 > /etc/TZ
  1294. [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
  1295. sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
  1296. unlink running file </var/run/rc.firewall.run>
  1297. [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WNDR3700v5" -c '**.cgi' -t 300&
  1298. unlink running file </var/run/rc.httpd.run>
  1299. [rc debug]/usr/sbin/rc remote_httpd start
  1300. ap_name=remote_httpd action=start
  1301. [rc.c::rc_action():803] rc_action before add remote_httpd - start
  1302. rc action <remote_httpd @ start> before file_lock.
  1303. rc action <remote_httpd @ start lock = 3> after file_lock.
  1304. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run
  1305. rc action < unlock = 3> after file_lock.
  1306. [rc.c::rc_action():811] rc_action after add remote_httpd - start
  1307. [rc.c::rc_start():706] Calling Start function of remote_httpd
  1308. unlink running file </var/run/rc.remote_httpd.run>
  1309. [rc debug]/usr/sbin/rc dhcpd start
  1310. ap_name=dhcpd action=start
  1311. [rc.c::rc_action():803] rc_action before add dhcpd - start
  1312. rc action <dhcpd @ start> before file_lock.
  1313. rc action <dhcpd @ start lock = 3> after file_lock.
  1314. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
  1315. rc action < unlock = 3> after file_lock.
  1316. [rc.c::rc_action():811] rc_action after add dhcpd - start
  1317. [rc.c::rc_start():706] Calling Start function of dhcpd
  1318. killall: udhcpd: no process killed
  1319. unlink running file </var/run/rc.dhcpd.run>
  1320. [rc debug]/usr/sbin/rc ntp start
  1321. ap_name=ntp action=start
  1322. [rc.c::rc_action():803] rc_action before add ntp - start
  1323. rc action <ntp @ start> before file_lock.
  1324. rc action <ntp @ start lock = 3> after file_lock.
  1325. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run
  1326. rc action < unlock = 3> after file_lock.
  1327. [rc.c::rc_action():811] rc_action after add ntp - start
  1328. [rc.c::rc_start():706] Calling Start function of ntp
  1329. [SYSTEM]/usr/sbin/netgear_ntp -z GMT+0&
  1330. [dhcpd.c::udhcpd():116] udhcp server (v0.9.7) started
  1331. [dhcpd.c::udhcpd():170] interface: br0, start : 201a8c0 end : fe01a8c0
  1332.  
  1333. unlink running file </var/run/rc.ntp.run>
  1334. [rc debug]/usr/sbin/rc route start
  1335. ap_name=route action=start
  1336. [rc.c::rc_action():803] rc_action before add route - start
  1337. rc action <route @ start> before file_lock.
  1338. rc action <route @ start lock = 3> after file_lock.
  1339. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
  1340. rc action < unlock = 3> after file_lock.
  1341. [rc.c::rc_action():811] rc_action after add route - start
  1342. [rc.c::rc_start():706] Calling Start function of route
  1343. unlink running file </var/run/rc.route.run>
  1344. [rc debug]/usr/sbin/rc ripd start
  1345. ap_name=ripd action=start
  1346. [rc.c::rc_action():803] rc_action before add ripd - start
  1347. rc action <ripd @ start> before file_lock.
  1348. rc action <ripd @ start lock = 3> after file_lock.
  1349. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run
  1350. rc action < unlock = 3> after file_lock.
  1351. [rc.c::rc_action():811] rc_action after add ripd - start
  1352. [rc.c::rc_start():706] Calling Start function of ripd
  1353. unlink running file </var/run/rc.ripd.run>
  1354. [rc debug]/usr/sbin/rc dnrd start
  1355. ap_name=dnrd action=start
  1356. [rc.c::rc_action():803] rc_action before add dnrd - start
  1357. rc action <dnrd @ start> before file_lock.
  1358. rc action <dnrd @ start lock = 3> after file_lock.
  1359. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
  1360. rc action < unlock = 3> after file_lock.
  1361. [rc.c::rc_action():811] rc_action after add dnrd - start
  1362. [rc.c::rc_start():706] Calling Start function of dnrd
  1363. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80
  1364. iptables: No chain/target/match by that name.
  1365. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1
  1366. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1
  1367. iptables: No chain/target/match by that name.
  1368. [SYSTEM]killall -9 dnrd
  1369. killall: dnrd: no process killed
  1370. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1
  1371. iptables: No chain/target/match by that name.
  1372. [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1
  1373. [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80
  1374. [SYSTEM]dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.com &
  1375. unlink running file </var/run/rc.dnrd.run>
  1376. [rc debug]/usr/sbin/rc potcounter start
  1377. ap_name=potcounter action=start
  1378. [rc.c::rc_action():803] rc_action before add potcounter - start
  1379. rc action <potcounter @ start> before file_lock.
  1380. rc action <potcounter @ start lock = 3> after file_lock.
  1381. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.potcounter.run
  1382. rc action < unlock = 3> after file_lock.
  1383. [rc.c::rc_action():811] rc_action after add potcounter - start
  1384. [rc.c::rc_start():706] Calling Start function of potcounter
  1385. unlink running file </var/run/rc.potcounter.run>
  1386. [rc debug]/usr/sbin/rc lltd start
  1387. ap_name=lltd action=start
  1388. [rc.c::rc_action():803] rc_action before add lltd - start
  1389. rc action <lltd @ start> before file_lock.
  1390. rc action <lltd @ start lock = 3> after file_lock.
  1391. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run
  1392. Notice: caching turned off
  1393. Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
  1394. rc action < unlock = 3> after file_lock.
  1395. [rc.c::rc_action():811] rc_action after add lltd - start
  1396. [rc.c::rc_start():706] Calling Start function of lltd
  1397. unlink running file </var/run/rc.lltd.run>
  1398. [rc debug]/usr/sbin/rc usb_init start
  1399. ap_name=usb_init action=start
  1400. [rc.c::rc_action():803] rc_action before add usb_init - start
  1401. rc action <usb_init @ start> before file_lock.
  1402. rc action <usb_init @ start lock = 3> after file_lock.
  1403. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_init.run
  1404. rc action < unlock = 3> after file_lock.
  1405. [rc.c::rc_action():811] rc_action after add usb_init - start
  1406. [rc.c::rc_start():706] Calling Start function of usb_init
  1407. [SYSTEM]/etc/mtk/mt7621_smp.sh wifi
  1408. [SYSTEM]/bin/rm /etc/samba/secrets.tdb
  1409. rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
  1410. [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
  1411. [SYSTEM]/usr/bin/killall -9 nmbd >/dev/null 2>&1
  1412. [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
  1413. [SYSTEM]/usr/sbin/killall -9 hd-idle
  1414. killall: hd-idle: no process killed
  1415. [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
  1416. [SYSTEM]/usr/sbin/killall -9 hd-idle
  1417. killall: hd-idle: no process killed
  1418. unlink running file </var/run/rc.usb_init.run>
  1419. [rc debug]/usr/sbin/rc debug_mode start
  1420. ap_name=debug_mode action=start
  1421. [rc.c::rc_action():803] rc_action before add debug_mode - start
  1422. rc action <debug_mode @ start> before file_lock.
  1423. rc action <debug_mode @ start lock = 3> after file_lock.
  1424. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run
  1425. rc action < unlock = 3> after file_lock.
  1426. [rc.c::rc_action():811] rc_action after add debug_mode - start
  1427. [rc.c::rc_start():706] Calling Start function of debug_mode
  1428. unlink running file </var/run/rc.debug_mode.run>
  1429. [rc debug]/usr/sbin/rc wifi_isolation start
  1430. ap_name=wifi_isolation action=start
  1431. [rc.c::rc_action():803] rc_action before add wifi_isolation - start
  1432. rc action <wifi_isolation @ start> before file_lock.
  1433. rc action <wifi_isolation @ start lock = 3> after file_lock.
  1434. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
  1435. rc action < unlock = 3> after file_lock.
  1436. [rc.c::rc_action():811] rc_action after add wifi_isolation - start
  1437. [rc.c::rc_start():706] Calling Start function of wifi_isolation
  1438. [SYSTEM]/bin/echo "lan_ip=192.168.1.1" > /proc/wifi_isolation
  1439. sh: cannot create /proc/wifi_isolation: nonexistent directory
  1440. [SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation
  1441. sh: cannot create /proc/wifi_isolation: nonexistent directory
  1442. unlink running file </var/run/rc.wifi_isolation.run>
  1443. [rc debug]/usr/sbin/rc mediaserver start
  1444. ap_name=mediaserver action=start
  1445. [rc.c::rc_action():803] rc_action before add mediaserver - start
  1446. rc action <mediaserver @ start> before file_lock.
  1447. rc action <mediaserver @ start lock = 3> after file_lock.
  1448. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.mediaserver.run
  1449. rc action < unlock = 3> after file_lock.
  1450. [rc.c::rc_action():811] rc_action after add mediaserver - start
  1451. [rc.c::rc_start():706] Calling Start function of mediaserver
  1452. #### media server is disable
  1453. unlink running file </var/run/rc.mediaserver.run>
  1454. [rc debug]/usr/sbin/rc bridge_iptv_port start
  1455. ap_name=bridge_iptv_port action=start
  1456. [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start
  1457. rc action <bridge_iptv_port @ start> before file_lock.
  1458. rc action <bridge_iptv_port @ start lock = 3> after file_lock.
  1459. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
  1460. rc action < unlock = 3> after file_lock.
  1461. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start
  1462. unlink running file </var/run/rc.bridge_iptv_port.run>
  1463. [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start
  1464. rc action <bridge_iptv_port @ start> before file_lock.
  1465. rc action <bridge_iptv_port @ start lock = 3> after file_lock.
  1466. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
  1467. rc action < unlock = 3> after file_lock.
  1468. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start
  1469. unlink running file </var/run/rc.bridge_iptv_port.run>
  1470. can't find this application
  1471. [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start
  1472. rc action <bridge_iptv_port @ start> before file_lock.
  1473. rc action <bridge_iptv_port @ start lock = 3> after file_lock.
  1474. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
  1475. rc action < unlock = 3> after file_lock.
  1476. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start
  1477. unlink running file </var/run/rc.bridge_iptv_port.run>
  1478. can't find this application
  1479. [rc debug]/usr/sbin/rc vlan start
  1480. ap_name=vlan action=start
  1481. [rc.c::rc_action():803] rc_action before add vlan - start
  1482. rc action <vlan @ start> before file_lock.
  1483. rc action <vlan @ start lock = 3> after file_lock.
  1484. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run
  1485. rc action < unlock = 3> after file_lock.
  1486. [rc.c::rc_action():811] rc_action after add vlan - start
  1487. unlink running file </var/run/rc.vlan.run>
  1488. [rc.c::rc_action():803] rc_action before add vlan - start
  1489. rc action <vlan @ start> before file_lock.
  1490. rc action <vlan @ start lock = 3> after file_lock.
  1491. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run
  1492. rc action < unlock = 3> after file_lock.
  1493. [rc.c::rc_action():811] rc_action after add vlan - start
  1494. unlink running file </var/run/rc.vlan.run>
  1495. can't find this application
  1496. [rc.c::rc_action():803] rc_action before add vlan - start
  1497. rc action <vlan @ start> before file_lock.
  1498. rc action <vlan @ start lock = 3> after file_lock.
  1499. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run
  1500. rc action < unlock = 3> after file_lock.
  1501. [rc.c::rc_action():811] rc_action after add vlan - start
  1502. unlink running file </var/run/rc.vlan.run>
  1503. can't find this application
  1504. [rc debug]/usr/sbin/rc dbus start
  1505. ap_name=dbus action=start
  1506. [rc.c::rc_action():803] rc_action before add dbus - start
  1507. rc action <dbus @ start> before file_lock.
  1508. rc action <dbus @ start lock = 3> after file_lock.
  1509. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
  1510. rc action < unlock = 3> after file_lock.
  1511. [rc.c::rc_action():811] rc_action after add dbus - start
  1512. unlink running file </var/run/rc.dbus.run>
  1513. [rc.c::rc_action():803] rc_action before add dbus - start
  1514. rc action <dbus @ start> before file_lock.
  1515. rc action <dbus @ start lock = 3> after file_lock.
  1516. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
  1517. rc action < unlock = 3> after file_lock.
  1518. [rc.c::rc_action():811] rc_action after add dbus - start
  1519. unlink running file </var/run/rc.dbus.run>
  1520. can't find this application
  1521. [rc.c::rc_action():803] rc_action before add dbus - start
  1522. rc action <dbus @ start> before file_lock.
  1523. rc action <dbus @ start lock = 3> after file_lock.
  1524. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
  1525. rc action < unlock = 3> after file_lock.
  1526. [rc.c::rc_action():811] rc_action after add dbus - start
  1527. unlink running file </var/run/rc.dbus.run>
  1528. can't find this application
  1529. =============rc finish
  1530. run smp wifi
  1531. run smp wifi done
  1532. PID USER VSZ STAT COMMAND
  1533. 1 root 1496 S init
  1534. 2 root 0 SW [kthreadd]
  1535. 3 root 0 SW [ksoftirqd/0]
  1536. 4 root 0 SW [kworker/0:0]
  1537. 5 root 0 SW [kworker/u:0]
  1538. 6 root 0 SW [migration/0]
  1539. 7 root 0 SW [migration/1]
  1540. 8 root 0 SW [kworker/1:0]
  1541. 9 root 0 SW [ksoftirqd/1]
  1542. 10 root 0 SW< [khelper]
  1543. 11 root 0 SW [kworker/1:1]
  1544. 12 root 0 SW [sync_supers]
  1545. 13 root 0 SW [bdi-default]
  1546. 14 root 0 SW< [kblockd]
  1547. 15 root 0 SW [khubd]
  1548. 16 root 0 SW [kswapd0]
  1549. 17 root 0 SW [fsnotify_mark]
  1550. 18 root 0 SW< [xfs_mru_cache]
  1551. 19 root 0 SW< [xfslogd]
  1552. 20 root 0 SW< [xfsdatad]
  1553. 21 root 0 SW< [xfsconvertd]
  1554. 22 root 0 SW< [crypto]
  1555. 29 root 0 SW [mtdblock0]
  1556. 30 root 0 SW [mtdblock1]
  1557. 31 root 0 SW [mtdblock2]
  1558. 32 root 0 SW [mtdblock3]
  1559. 33 root 0 SW [mtdblock4]
  1560. 34 root 0 SW [mtdblock5]
  1561. 35 root 0 SW [mtdblock6]
  1562. 36 root 0 SW [mtdblock7]
  1563. 37 root 0 SW [mtdblock8]
  1564. 38 root 0 SW [mtdblock9]
  1565. 39 root 0 SW [mtdblock10]
  1566. 40 root 0 SW [mtdblock11]
  1567. 41 root 0 SW [mtdblock12]
  1568. 42 root 0 SW [mtdblock13]
  1569. 43 root 0 SW [mtdblock14]
  1570. 44 root 0 SW [mtdblock15]
  1571. 45 root 0 SW [mtdblock16]
  1572. 46 root 0 SW [mtdblock17]
  1573. 47 root 0 SW [mtdblock18]
  1574. 48 root 0 SW [mtdblock19]
  1575. 49 root 0 SW [kworker/u:1]
  1576. 56 root 0 SW [kworker/0:1]
  1577. 58 root 1496 S /bin/sh /usr/etc/rcS
  1578. 146 root 1032 S /sbin/klogd
  1579. 148 root 920 S /usr/sbin/cmd_agent_ap
  1580. 218 root 1024 S /sbin/access_logd
  1581. 231 root 1136 S /sbin/access_devinfo
  1582. 255 root 1212 S /usr/sbin/scfgmgr
  1583. 286 root 0 SW [RtmpCmdQTask]
  1584. 287 root 0 SW [RtmpWscTask]
  1585. 288 root 0 SW [RtmpMlmeTask]
  1586. 295 root 0 SW [RtmpCmdQTask]
  1587. 296 root 0 SW [RtmpWscTask]
  1588. 297 root 0 SW [RtmpMlmeTask]
  1589. 318 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -
  1590. 360 root 1092 S /sbin/syslogd -f /etc/syslog.conf
  1591. 871 root 1048 S /usr/sbin/udhcpd /etc/udhcpd.conf
  1592. 876 root 940 S /usr/sbin/netgear_ntp -z GMT+0
  1593. 878 root 1444 S /usr/sbin/mini_httpd -d /www -r NETGEAR WNDR3700v5 -c
  1594. 1523 root 928 S /usr/sbin/potcounter
  1595. 1527 root 1432 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co
  1596. 1531 root 1144 S /usr/bin/lld2 br0
  1597. 1573 root 940 S telnetenabled 192.168.1.1 A42B8C58FA38 admin password
  1598. 1623 root 1496 R /bin/ps
  1599. [rc debug]/usr/sbin/rc upnp start
  1600. ap_name=upnp action=start
  1601. [rc.c::rc_action():803] rc_action before add upnp - start
  1602. rc action <upnp @ start> before file_lock.
  1603. rc action <upnp @ start lock = 3> after file_lock.
  1604. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
  1605. rc action < unlock = 3> after file_lock.
  1606. [rc.c::rc_action():811] rc_action after add upnp - start
  1607. unlink running file </var/run/rc.upnp.run>
  1608. [rc.c::rc_action():803] rc_action before add upnp - start
  1609. rc action <upnp @ start> before file_lock.
  1610. rc action <upnp @ start lock = 3> after file_lock.
  1611. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
  1612. rc action < unlock = 3> after file_lock.
  1613. [rc.c::rc_action():811] rc_action after add upnp - start
  1614. unlink running file </var/run/rc.upnp.run>
  1615. can't find this application
  1616. [rc.c::rc_action():803] rc_action before add upnp - start
  1617. rc action <upnp @ start> before file_lock.
  1618. rc action <upnp @ start lock = 3> after file_lock.
  1619. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
  1620. rc action < unlock = 3> after file_lock.
  1621. [rc.c::rc_action():811] rc_action after add upnp - start
  1622. [rc.c::rc_start():706] Calling Start function of upnp
  1623. [SYSTEM]route add -net 239.0.0.0 netmask 255.0.0.0 br0
  1624. [SYSTEM]/usr/sbin/miniupnpd -i eth3 -a 192.168.1.1 -p 56688 -U -t 1800 -T 4 -u 824ff22b-8c7d-41c5-a131-a42b8c58fa38
  1625. unlink running file </var/run/rc.upnp.run>
  1626. route: SIOCADDRT: File exists
  1627. [rc debug]/usr/sbin/rc schedule restart
  1628. [rc.c::rc_action():803] rc_action before add schedule - restart
  1629. rc action <schedule @ restart> before file_lock.
  1630. rc action <schedule @ restart lock = 3> after file_lock.
  1631. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run
  1632. rc action < unlock = 3> after file_lock.
  1633. [rc.c::rc_action():811] rc_action after add schedule - restart
  1634. unlink running file </var/run/rc.schedule.run>
  1635. [rc.c::rc_action():803] rc_action before add schedule - restart
  1636. rc action <schedule @ restart> before file_lock.
  1637. rc action <schedule @ restart lock = 3> after file_lock.
  1638. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run
  1639. rc action < unlock = 3> after file_lock.
  1640. [rc.c::rc_action():811] rc_action after add schedule - restart
  1641. [rc.c::rc_start():706] Calling Start function of schedule
  1642. /usr/etc/rcS: line 282: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
  1643. /usr/etc/rcS: line 283: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
  1644. /usr/etc/rcS: line 287: cannot create [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02
  1645. /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory
  1646. [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
  1647. [SYSTEM]/bin/echo GMT+0 > /etc/TZ
  1648. [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
  1649. unlink running file </var/run/rc.schedule.run>
  1650. [rc debug][rc debug]usr/sbin/rc /usr/sbin/rc reset_lan wan start start
  1651.  
  1652. ap_name=reset_lan action=start
  1653. [rc.c::rc_action():803] rc_action before add reset_lan - start
  1654. rc action <reset_lan @ start> before file_lock.
  1655. rc action <reset_lan @ start lock = 3> after file_lock.
  1656. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
  1657. [SYSTEM]/usr/sbin/brctl delif br0 eth3
  1658. rc action < unlock = 3> after file_lock.
  1659. [rc.c::rc_action():811] rc_action after add reset_lan - start
  1660. unlink running file </var/run/rc.reset_lan.run>
  1661. [rc.c::rc_action():803] rc_action before add reset_lan - start
  1662. rc action <reset_lan @ start> before file_lock.
  1663. rc action <reset_lan @ start lock = 3> after file_lock.
  1664. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
  1665. rc action < unlock = 3> after file_lock.
  1666. [rc.c::rc_action():811] rc_action after add reset_lan - start
  1667. unlink running file </var/run/rc.reset_lan.run>
  1668. can't find this application
  1669. [rc.c::rc_action():803] rc_action before add reset_lan - start
  1670. rc action <reset_lan @ start> before file_lock.
  1671. rc action <reset_lan @ start lock = 3> after file_lock.
  1672. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
  1673. device eth3 is not a slave of br0
  1674. [SYSTEM]/usr/bin/killall netgear_ntp
  1675. rc action < unlock = 3> after file_lock.
  1676. [rc.c::rc_action():811] rc_action after add reset_lan - start
  1677. [rc.c::rc_start():706] Calling Start function of reset_lan
  1678. down port 0
  1679. Set: phy[0].reg[0] = 1840
  1680. down port 1
  1681. [SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
  1682. killall: ripd: no process killed
  1683. Set: phy[1].reg[0] = 1840
  1684. killall: zebra: no process killed
  1685. down port 2
  1686. Set: phy[2].reg[0] = 1840
  1687. down port 3
  1688. Set: phy[3].reg[0] = 1840
  1689. killall: ripd: no process killed
  1690. killall: zebra: no process killed
  1691. [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
  1692. [SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
  1693. [SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE
  1694. [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
  1695. [SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP
  1696. sh: syntax error: "(" unexpected
  1697. [SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
  1698. [SYSTEM]/usr/bin/killall pppd
  1699. killall: pppd: no process killed
  1700. [SYSTEM]/usr/bin/killall openl2tpd
  1701. killall: openl2tpd: no process killed
  1702. [SYSTEM]/usr/bin/killall udhcpc
  1703. killall: udhcpc: no process killed
  1704. [SYSTEM]/usr/bin/killall pppoe-relay
  1705. killall: pppoe-relay: no process killed
  1706. [SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1
  1707. [SYSTEM]/sbin/ifconfig eth3 down
  1708. [SYSTEM]/sbin/ifconfig eth3 hw ether XX:XX:XX:XX:XX:XX
  1709. [SYSTEM]/sbin/ifconfig eth3 up
  1710. [SYSTEM]/sbin/ifconfig eth3 mtu 1500
  1711. [wan/wan.c::start_wan():1372] wan_mode is <dhcpc>
  1712. [SYSTEM]/bin/echo 3 > /proc/sys/vm/drop_caches; /bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
  1713. [SYSTEM]/usr/sbin/udhcpc -i eth3 -s /etc/udhcpc.script -H "WNDR3700v5" &
  1714. [wan/wan.c::start_wan():1456] ipv6 restart, v4 mode dhcpc v6 mode disable
  1715. [SYSTEM]/usr/sbin/rc ipv6 restart
  1716. [dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started
  1717. [clientpacket.c::send_discover():175] Sending discover...
  1718. [rc debug]/usr/sbin/rc ipv6 restart
  1719. ap_name=ipv6 action=restart
  1720. [rc.c::rc_action():803] rc_action before add ipv6 - restart
  1721. rc action <ipv6 @ restart> before file_lock.
  1722. rc action <ipv6 @ restart lock = 3> after file_lock.
  1723. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
  1724. rc action < unlock = 3> after file_lock.
  1725. [rc.c::rc_action():811] rc_action after add ipv6 - restart
  1726. unlink running file </var/run/rc.ipv6.run>
  1727. [rc.c::rc_action():803] rc_action before add ipv6 - restart
  1728. rc action <ipv6 @ restart> before file_lock.
  1729. rc action <ipv6 @ restart lock = 3> after file_lock.
  1730. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
  1731. rc action < unlock = 3> after file_lock.
  1732. [rc.c::rc_action():811] rc_action after add ipv6 - restart
  1733. unlink running file </var/run/rc.ipv6.run>
  1734. can't find this application
  1735. [rc.c::rc_action():803] rc_action before add ipv6 - restart
  1736. rc action <ipv6 @ restart> before file_lock.
  1737. rc action <ipv6 @ restart lock = 3> after file_lock.
  1738. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
  1739. rc action < unlock = 3> after file_lock.
  1740. [rc.c::rc_action():811] rc_action after add ipv6 - restart
  1741. [rc.c::rc_stop():745] Calling Stop function of ipv6
  1742. [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv6/conf/all/forwarding
  1743. [SYSTEM]/usr/bin/killall dhcp6c
  1744. killall: dhcp6c: no process killed
  1745. [SYSTEM]/bin/killall pppd_ip6
  1746. killall: pppd_ip6: no process killed
  1747. [SYSTEM]/usr/bin/killall radvd
  1748. killall: radvd: no process killed
  1749. [SYSTEM]/usr/bin/killall -9 dhcp6s
  1750. killall: dhcp6s: no process killed
  1751. [SYSTEM]/bin/killall -9 totd
  1752. killall: totd: no process killed
  1753. [SYSTEM]ip6tables -t filter -F
  1754. up port 0
  1755. [SYSTEM]ip6tables -t mangle -F
  1756. [SYSTEM]ip6tables -t raw -F
  1757. Set: phy[0].reg[0] = 1240
  1758. [SYSTEM]ip6tables -t filter -X
  1759. up port 1
  1760. [SYSTEM]ip6tables -t mangle -X
  1761. Set: phy[1].reg[0] = 1240
  1762. [SYSTEM]ip6tables -t raw -X
  1763. up port 2
  1764. [SYSTEM]ip6tables -t filter -P INPUT ACCEPT
  1765. Set: phy[2].reg[0] = 1240
  1766. up port 3
  1767. [SYSTEM]ip6tables -t filter -P FORWARD ACCEPT
  1768. Set: phy[3].reg[0] = 1240
  1769. unlink running file </var/run/rc.reset_lan.run>
  1770. [SYSTEM]ip6tables -C /tmp/rules6
  1771. ip6tables v1.4.10: option `-C' requires an argument
  1772. Try `ip6tables -h' or 'ip6tables --help' for more information.
  1773. [SYSTEM]killall mld
  1774. killall: mld: no process killed
  1775. [SYSTEM]/sbin/ip -6 route flush dev tun6to4
  1776. Cannot find device "tun6to4"
  1777. [SYSTEM]/sbin/ip link set dev tun6to4 down
  1778. SIOCGIFFLAGS: No such device
  1779. [SYSTEM]/sbin/ip tunnel del tun6to4
  1780. ioctl: No such device
  1781. [SYSTEM]/sbin/rmmod ipv6_br.ko
  1782. rmmod: ipv6_br.ko: No such file or directory
  1783. [SYSTEM]/usr/bin/killall dhcp6c
  1784. killall: dhcp6c: no process killed
  1785. [SYSTEM]/usr/bin/killall ip6_autod
  1786. killall: ip6_autod: no process killed
  1787. [SYSTEM]/bin/rm -f /var/ip6prefix*
  1788. [ipv6/ipv6.c::stop_ipv6():72] stop ip6 wan mode: (-1)
  1789. [SYSTEM]/bin/ip -6 route del
  1790. RTNETLINK answers: No such file or directory
  1791. [SYSTEM]/bin/ip -6 route del
  1792. RTNETLINK answers: No such file or directory
  1793. [SYSTEM]/bin/ip -6 route del
  1794. RTNETLINK answers: No such file or directory
  1795. [SYSTEM]/bin/ip -6 route del
  1796. RTNETLINK answers: No such file or directory
  1797. [SYSTEM]/bin/ip -6 route del
  1798. RTNETLINK answers: No such file or directory
  1799. [SYSTEM]/bin/ip -6 route del
  1800. RTNETLINK answers: No such file or directory
  1801. [rc.c::rc_start():706] Calling Start function of ipv6
  1802. [ipv6/common.c::ip6_config_dump():146] lan_ifname = <br0>
  1803. [ipv6/common.c::ip6_config_dump():147] wan_ifname = <eth3>
  1804. [ipv6/common.c::ip6_config_dump():148] wan_l2_ifname = <eth3>
  1805. [ipv6/common.c::ip6_config_dump():149] wan_ppp_ifname = <ppp6>
  1806. [ipv6/common.c::ip6_config_dump():150] wan_mode = 0
  1807. [ipv6/common.c::ip6_config_dump():151] lan_mode = 2
  1808. [ipv6/common.c::ip6_config_dump():152] dhcp_account = <>
  1809. [ipv6/common.c::ip6_config_dump():153] dhcp_domain = <>
  1810. [ipv6/common.c::ip6_config_dump():154] pppoe_username = <>
  1811. [ipv6/common.c::ip6_config_dump():155] pppoe_passwd = <>
  1812. [ipv6/common.c::ip6_config_dump():156] pppoe_service = <>
  1813. [ipv6/common.c::ip6_config_dump():157] custom_relay_router = 0
  1814. [ipv6/common.c::ip6_config_dump():158] relay_router = <>
  1815. [ipv6/common.c::ip6_config_dump():159] fixed_wan_ipaddr = <>
  1816. [ipv6/common.c::ip6_config_dump():160] fixed_gw_ipaddr = <>
  1817. [ipv6/common.c::ip6_config_dump():161] fixed_wan_plen = 0
  1818. [ipv6/common.c::ip6_config_dump():162] fixed_lan_ipaddr = <>
  1819. [ipv6/common.c::ip6_config_dump():163] fixed_lan_plen = 0
  1820. [ipv6/common.c::ip6_config_dump():164] fixed_dns1 = <>
  1821. [ipv6/common.c::ip6_config_dump():165] fixed_dns2 = <>
  1822. [ipv6/common.c::ip6_config_dump():166] custom_ifid_enable = 0
  1823. [ipv6/common.c::ip6_config_dump():169] ifid = <0000:0000:0000:0000>
  1824. [ipv6/common.c::ip6_config_dump():171] ipv6ipv4ppp_one_session = 0
  1825. [ipv6/common.c::ip6_config_dump():172] ipv6_ppp_stateless = 0
  1826. [ipv6/common.c::ip6_config_dump():173] ipv6_dhcpc_no_na = 0
  1827. [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6
  1828. [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/all/forwarding
  1829. [ipv6/ipv6.c::start_ipv6():163] ipv6 is over layer2, open rs/ra on eth3
  1830. [SYSTEM]/bin/echo 3 > /proc/sys/net/ipv6/conf/eth3/router_solicitations
  1831. [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/eth3/accept_ra
  1832. [ipv6/ipv6.c::start_ipv6():167] ipv6 is over layer2 interface eth3, trigger wan send out router solicitation
  1833. [SYSTEM]/bin/echo trigger_rs=1 > /proc/net/trigger_rs
  1834. [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/trigger_rs
  1835. [ipv6/ipv6.c::start_ipv6():186] ip6 is disabled.
  1836. unlink running file </var/run/rc.ipv6.run>
  1837. [clientpacket.c::send_discover():175] Sending discover...
  1838. [clientpacket.c::send_discover():175] Sending discover...
  1839. [rc debug]/usr/sbin/rc usb_printer start
  1840. ap_name=usb_printer action=start
  1841. [rc.c::rc_action():803] rc_action before add usb_printer - start
  1842. rc action <usb_printer @ start> before file_lock.
  1843. rc action <usb_printer @ start lock = 3> after file_lock.
  1844. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
  1845. rc action < unlock = 3> after file_lock.
  1846. [rc.c::rc_action():811] rc_action after add usb_printer - start
  1847. unlink running file </var/run/rc.usb_printer.run>
  1848. [rc.c::rc_action():803] rc_action before add usb_printer - start
  1849. rc action <usb_printer @ start> before file_lock.
  1850. rc action <usb_printer @ start lock = 3> after file_lock.
  1851. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
  1852. rc action < unlock = 3> after file_lock.
  1853. [rc.c::rc_action():811] rc_action after add usb_printer - start
  1854. unlink running file </var/run/rc.usb_printer.run>
  1855. can't find this application
  1856. [rc.c::rc_action():803] rc_action before add usb_printer - start
  1857. rc action <usb_printer @ start> before file_lock.
  1858. rc action <usb_printer @ start lock = 3> after file_lock.
  1859. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
  1860. rc action < unlock = 3> after file_lock.
  1861. [rc.c::rc_action():811] rc_action after add usb_printer - start
  1862. [rc.c::rc_start():706] Calling Start function of usb_printer
  1863. [SYSTEM]/sbin/killall KC_BONJOUR
  1864. cable_down_once
  1865. killall: KC_BONJOUR: no process killed
  1866. [SYSTEM]/sbin/killall KC_PRINT
  1867. [rc debug]/usr/sbin/rc down_manage stop
  1868. ap_name=down_manage action=stop
  1869. [rc.c::rc_action():803] rc_action before add down_manage - stop
  1870. rc action <down_manage @ stop> before file_lock.
  1871. rc action <down_manage @ stop lock = 3> after file_lock.
  1872. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
  1873. rc action < unlock = 3> after file_lock.
  1874. [rc.c::rc_action():811] rc_action after add down_manage - stop
  1875. unlink running file </var/run/rc.down_manage.run>
  1876. [rc.c::rc_action():803] rc_action before add down_manage - stop
  1877. rc action <down_manage @ stop> before file_lock.
  1878. rc action <down_manage @ stop lock = 3> after file_lock.
  1879. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
  1880. rc action < unlock = 3> after file_lock.
  1881. [rc.c::rc_action():811] rc_action after add down_manage - stop
  1882. unlink running file </var/run/rc.down_manage.run>
  1883. can't find this application
  1884. [rc.c::rc_action():803] rc_action before add down_manage - stop
  1885. rc action <down_manage @ stop> before file_lock.
  1886. rc action <down_manage @ stop lock = 3> after file_lock.
  1887. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
  1888. killall: KC_PRINT: no process killed
  1889. [SYSTEM]/sbin/rmmod usblp
  1890. rmmod: usblp: No such file or directory
  1891. [SYSTEM]/sbin/rmmod NetUSB.ko
  1892. rc action < unlock = 3> after file_lock.
  1893. [rc.c::rc_action():811] rc_action after add down_manage - stop
  1894. unlink running file </var/run/rc.down_manage.run>
  1895. can't find this application
  1896. rmmod: NetUSB.ko: No such file or directory
  1897. [SYSTEM]/sbin/rmmod GPL_NetUSB.ko
  1898. rmmod: GPL_NetUSB.ko: No such file or directory
  1899. [dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=51
  1900. ==================
  1901. interface=eth3
  1902. PATH=/bin:/sbin:/usr/sbin:/usr/bin
  1903. HOME=/
  1904. route_related_options_del_file=/tmp/dhcpc_route_related_options_del
  1905. ==================
  1906. [SYSTEM]/sbin/insmod /lib/modules/GPL_NetUSB.ko
  1907. rm: cannot remove '/tmp/wan_uptime': No such file or directory
  1908. rm: cannot remove '/tmp/wan_ipaddr': No such file or directory
  1909. rm: cannot remove '/tmp/dhcpc.lease': No such file or directory
  1910. deleting dhcpc options releated routers
  1911. /bin/sh: can't open /tmp/dhcpc_route_related_options_del
  1912. [rc debug]/usr/sbin/rc route restart
  1913. ap_name=route action=restart
  1914. [rc.c::rc_action():803] rc_action before add route - restart
  1915. rc action <route @ restart> before file_lock.
  1916. rc action <route @ restart lock = 4> after file_lock.
  1917. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
  1918. rc action < unlock = 4> after file_lock.
  1919. [rc.c::rc_action():811] rc_action after add route - restart
  1920. [rc.c::rc_stop():745] Calling Stop function of route
  1921. [SYSTEM]/sbin/insmod /lib/modules/NetUSB.ko localID="WNDR3700v5"
  1922. [rc.c::rc_start():706] Calling Start function of route
  1923. unlink running file </var/run/rc.route.run>
  1924. [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/class/usblp.ko
  1925. [SYSTEM]/sbin/KC_BONJOUR WNDR3700v5 &
  1926. [SYSTEM]/sbin/KC_PRINT WNDR3700v5 &
  1927. unlink running file </var/run/rc.usb_printer.run>
  1928. PID USER VSZ STAT COMMAND
  1929. 1 root 1496 S init
  1930. 2 root 0 SW [kthreadd]
  1931. 3 root 0 SW [ksoftirqd/0]
  1932. 4 root 0 SW [kworker/0:0]
  1933. 5 root 0 SW [kworker/u:0]
  1934. 6 root 0 SW [migration/0]
  1935. 7 root 0 SW [migration/1]
  1936. 8 root 0 SW [kworker/1:0]
  1937. 9 root 0 SW [ksoftirqd/1]
  1938. 10 root 0 SW< [khelper]
  1939. 11 root 0 SW [kworker/1:1]
  1940. 12 root 0 SW [sync_supers]
  1941. 13 root 0 SW [bdi-default]
  1942. 14 root 0 SW< [kblockd]
  1943. 15 root 0 SW [khubd]
  1944. 16 root 0 SW [kswapd0]
  1945. 17 root 0 SW [fsnotify_mark]
  1946. 18 root 0 SW< [xfs_mru_cache]
  1947. 19 root 0 SW< [xfslogd]
  1948. 20 root 0 SW< [xfsdatad]
  1949. 21 root 0 SW< [xfsconvertd]
  1950. 22 root 0 SW< [crypto]
  1951. 29 root 0 SW [mtdblock0]
  1952. 30 root 0 SW [mtdblock1]
  1953. 31 root 0 SW [mtdblock2]
  1954. 32 root 0 RW [mtdblock3]
  1955. 33 root 0 SW [mtdblock4]
  1956. 34 root 0 SW [mtdblock5]
  1957. 35 root 0 SW [mtdblock6]
  1958. 36 root 0 SW [mtdblock7]
  1959. 37 root 0 SW [mtdblock8]
  1960. 38 root 0 SW [mtdblock9]
  1961. 39 root 0 SW [mtdblock10]
  1962. 40 root 0 SW [mtdblock11]
  1963. 41 root 0 SW [mtdblock12]
  1964. 42 root 0 SW [mtdblock13]
  1965. 43 root 0 SW [mtdblock14]
  1966. 44 root 0 SW [mtdblock15]
  1967. 45 root 0 SW [mtdblock16]
  1968. 46 root 0 SW [mtdblock17]
  1969. 47 root 0 SW [mtdblock18]
  1970. 48 root 0 SW [mtdblock19]
  1971. 49 root 0 SW [kworker/u:1]
  1972. 56 root 0 SW [kworker/0:1]
  1973. 58 root 1496 S /bin/sh /usr/etc/rcS
  1974. 146 root 1032 S /sbin/klogd
  1975. 148 root 920 S /usr/sbin/cmd_agent_ap
  1976. 218 root 1024 S /sbin/access_logd
  1977. 231 root 1136 S /sbin/access_devinfo
  1978. 255 root 1212 S /usr/sbin/scfgmgr
  1979. [Bonjour] Interface: br0 is connected
  1980. [KC] WNDR3700v5 IPP v1.3 Start (Jun 26 2014 09:59:43)
  1981. 286 root 0 SW [RtmpCmdQTask]
  1982. 287 root 0 SW [RtmpWscTask]
  1983. 288 root 0 SW [RtmpMlmeTask]
  1984. 295 root 0 SW [RtmpCmdQTask]
  1985. 296 root 0 SW [RtmpWscTask]
  1986. 297 root 0 SW [RtmpMlmeTask]
  1987. 318 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -
  1988. 360 root 1092 S /sbin/syslogd -f /etc/syslog.conf
  1989. 871 root 1048 S /usr/sbin/udhcpd /etc/udhcpd.conf
  1990. 878 root 1444 S /usr/sbin/mini_httpd -d /www -r NETGEAR WNDR3700v5 -c
  1991. 1523 root 928 S /usr/sbin/potcounter
  1992. 1527 root 1432 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co
  1993. 1531 root 1144 S /usr/bin/lld2 br0
  1994. 1573 root 940 S telnetenabled 192.168.1.1 A42B8C58FA38 admin password
  1995. 1636 root 1360 S /usr/sbin/miniupnpd -i eth3 -a 192.168.1.1 -p 56688 -
  1996. 1637 root 948 S /usr/sbin/crond
  1997. 1638 root 1396 S /usr/sbin/multi_pb_app 90 91 92 10 50
  1998. 1640 root 0 Z [crond]
  1999. 1641 root 0 Z [crond]
  2000. 1691 root 924 S /usr/sbin/cmd_agent
  2001. 2035 root 1024 S /usr/sbin/udhcpc -i eth3 -s /etc/udhcpc.script -H WND
  2002. 2782 root 1100 S usr/sbin/wan_monitor
  2003. 2835 root 0 SW [ telnetDBGD ]
  2004. 2836 root 0 SW [ acktelnetDBGD ]
  2005. 2837 root 0 SW [checkSBusTimeou]
  2006. 2839 root 0 SW [NU UDP]
  2007. 2840 root 0 SW [NU TCP]
  2008. 2844 root 404 S /sbin/KC_BONJOUR WNDR3700v5
  2009. 2846 root 456 S /sbin/KC_PRINT WNDR3700v5
  2010. 2847 root 1496 R /bin/ps
  2011. 2848 root 404 S /sbin/KC_BONJOUR WNDR3700v5
  2012. 2849 root 404 S /sbin/KC_BONJOUR WNDR3700v5
  2013. 2854 root 456 S /sbin/KC_PRINT WNDR3700v5
  2014. 2855 root 404 S /sbin/KC_BONJOUR WNDR3700v5
  2015. 2856 root 456 S /sbin/KC_PRINT WNDR3700v5
  2016. 2857 root 404 S /sbin/KC_BONJOUR WNDR3700v5
  2017. 2858 root 456 S /sbin/KC_PRINT WNDR3700v5
  2018. /usr/etc/rcS: line 347: /usr/sbin/led_test: not found
  2019. starting pid 2861, tty '/dev/ttyS1': '/bin/sh'
  2020. # INFO14C9: Bind to br0
  2021. [Bonjour] MDNS_CheckName: receive packet timeout
  2022. [Bonjour] default device name = WNDR3700v5
  2023. [Bonjour] Answer Name Start (192.168.1.1)
  2024. [KC] WNDR3700v5 IPP v1.3 Start (Jun 26 2014 09:59:50)
RAW Paste Data