SHARE
TWEET

Almond+ boot output

a guest Oct 20th, 2018 15 in 117 days
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. Copyright 2011 Cortina Systems - Golden Gate
  2. JTAG ID: 0x101083e5
  3. CPU Speed : 750 MHz
  4. CPU PLL(0): Locked
  5. Core PLL(1): Locked
  6. Peripheral PLL(2): Locked
  7. DDR PLL(3): Locked
  8. Flash Type : F:5 S:0 Width : 0 Size : 2 Pin: 0
  9. BOOT: NAND
  10. BOOT: Jumping to boot loader...
  11. 2nd CPU Switch to RRAM1 successfully
  12.  
  13. Cortina Systems Power-On Self-Test 0.99
  14.  Build Info: May 22 2014 09:12:24
  15. Hit key [m] before reset/power_on to enter DDR memory config and POST prompt
  16. Setup DDR, do memory check, and then go to UBOOT
  17. Started Denali SDRAM Controller Configuration...
  18. DONE Denali SDRAM Controller Configuration...
  19. Started SDRAM PHY Configuration...
  20. DONE SDRAM PHY Configuration...
  21. Initiate Denali SDRAM Controller initialization
  22. Waiting for SDRAM initialization to complete
  23. SDRAM initialization DONE.............
  24. Performing train RD strobe
  25. byte lane#0:
  26.         Right hand margin is 39
  27.         Left hand margin is 16
  28. byte lane#1:
  29.         Right hand margin is 40
  30.         Left hand margin is 22
  31. byte lane#2:
  32.         Right hand margin is 41
  33.         Left hand margin is 22
  34. byte lane#3:
  35.         Right hand margin is 39
  36.         Left hand margin is 26
  37. ADDR: 0xf0500220  VAL: 0x0609090b
  38.  
  39. Performing train RD latency
  40. Read delay adjusted at rdlat_adj=10 dram_class=6
  41. ADDR: 0xf0500080  VAL: 0x00000000
  42. ADDR: 0xf0500160  VAL: 0x050b0c2d
  43.  
  44. Performing train gating
  45. Right hand margin is 63 for GATEO
  46. Left hand margin is 63 for GATEO
  47. ADDR: 0xf0500218  VAL: 0x00000600
  48. ADDR: 0xf0500080  VAL: 0x01000000
  49.  
  50. Performing train write data
  51. byte lane#0:
  52. Right hand margin is 39
  53. Left hand margin is 63
  54. byte lane#1:
  55. Right hand margin is 46
  56. Left hand margin is 63
  57. byte lane#2:
  58. Right hand margin is 40
  59. Left hand margin is 63
  60. byte lane#3:
  61. Right hand margin is 38
  62. Left hand margin is 63
  63. ADDR: 0xf0500224  VAL: 0x4c4b484c
  64. ADDR: 0xf0500080  VAL: 0x01000000
  65. SDRAM_DENALI_CTL_161: 0x30002001
  66.  
  67. Memory size detected as 512 Mbyte
  68. Denali SDRAM Controller initialization Done
  69.  
  70. Memory Test St Address 0x00800000 Len 0x00400000: Passed
  71. Copy flash code from 0xf6a07cf0 to 0x04000000 length = 0x00026414
  72.  
  73. POST: execution transfer to u-boot 0x04000000
  74.  
  75.  
  76.  
  77. U-Boot 2009.11-dirty (Jun 28 2014 - 16:51:17) GoldenGate SoC ASIC
  78.  
  79. DRAM:  512 MB
  80. NAND:  512 MiB
  81. In:    serial
  82. Out:   serial
  83. Err:   serial
  84. Net:   Connect GMAC1 to CPU
  85. Goldengate
  86. Hit any key to stop autoboot:  0
  87. Kernel: Copy 4784728 bytes from flash address 0xe0600000 to RAM address 0x02100000 ...
  88. Checking MD5 at address 0x02100000 for 4784728 bytes ...
  89. Booting from SB at 0xe0400000
  90. ## Booting kernel from Legacy Image at 02100000 ...
  91.    Image Name:   Linux-2.6.36
  92.    Image Type:   ARM Linux Kernel Image (uncompressed)
  93.    Data Size:    4784664 Bytes =  4.6 MB
  94.    Load Address: 00008000
  95.    Entry Point:  00008000
  96.    Loading Kernel Image ... OK
  97. OK
  98.  
  99. Starting kernel ...
  100.  
  101. Uncompressing Linux... done, booting the kernel.
  102. Linux version 2.6.36 (buildserver@buildserver) (gcc version 4.5.2 20101126 (Linaro) [release 4.5-2010.12-0] (GCC) ) #1096 SMP PREEMPT Thu Jul 10 17:35:17 IST 2014
  103. CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c53c7f
  104. CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  105. Machine: CORTINA-G2 EB
  106. Mem_size=512
  107. Ignoring unrecognised tag 0x00000000
  108. Memory policy: ECC disabled, Data cache writealloc
  109. PERCPU: Embedded 7 pages/cpu @81672000 s5376 r8192 d15104 u65536
  110. pcpu-alloc: s5376 r8192 d15104 u65536 alloc=16*4096
  111. pcpu-alloc: [0] 0 [0] 1
  112. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 113792
  113. Kernel command line: console=ttyS0,115200 SB_PHY=PPPS ni_napi_budget=16 qm_acp_enable=0 ni_rx_noncache=0 qm_int_buff=0 ethaddr0=xx:xx:xx:xx:xx:xx ethaddr1=xx:xx:xx:xx:xx:xx ethaddr2=xx:xx:xx:xx:xx:xx wifiaddr0=xx:xx:xx:xx:xx:xx wifiaddr1=xx:xx:xx:xx:xx:xx mtdparts=cs752x_nand_flash:1024K@0x00100000(uboot-env0),1024K@0x00300000(uboot-env1),1024K@0x00400000(sb0),1024K@0x00500000(sb1),47104K@0x00C00000(rootfs),6144K@0x03A00000(kernel_standby),47104K@0x04000000(rootfs_standby),16384K@0x6E00000(rootfs_data),1024K@0x07E00000(log),1024K@0x07F00000(cal),1024K@0x08000000(man),5120K@0x08100000(Almond_Data),896K@0x20000(uboot0),1024K@0x00200000(uboot1)
  114. get_ni_napi_budget: ni_napi_budget=16
  115. get_ni_rx_noncache: ni_rx_noncache=0
  116. PID hash table entries: 2048 (order: 1, 8192 bytes)
  117. Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  118. Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  119. Memory: 448MB = 448MB total
  120. Memory: 429136k/429136k available, 29616k reserved, 0K highmem
  121. Virtual kernel memory layout:
  122.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  123.     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  124.     DMA     : 0xfbe00000 - 0xffe00000   (  64 MB)
  125.     vmalloc : 0x9c800000 - 0xef000000   (1320 MB)
  126.     lowmem  : 0x80000000 - 0x9c000000   ( 448 MB)
  127.     modules : 0x7f000000 - 0x80000000   (  16 MB)
  128.       .init : 0x80008000 - 0x80038000   ( 192 kB)
  129.       .text : 0x80038000 - 0x8075e000   (7320 kB)
  130.       .data : 0x8075e000 - 0x80922c80   (1812 kB)
  131. SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  132. Hierarchical RCU implementation.
  133.         RCU-based detection of stalled CPUs is disabled.
  134.         Verbose stalled-CPUs detection is disabled.
  135. NR_IRQS:315
  136. Max IRQs supported by GIC 96
  137. APB Clock :150000000
  138. Console: colour dummy device 80x30
  139. console [ttyS0] enabled
  140. Calibrating delay loop... 1497.49 BogoMIPS (lpj=7487488)
  141. pid_max: default: 32768 minimum: 301
  142. Mount-cache hash table entries: 512
  143. CPU: Testing write buffer coherency: ok
  144. Calibrating local timer... 149.99MHz.
  145. CPU1: Booted secondary processor
  146. Brought up 2 CPUs
  147. SMP: Total of 2 processors activated (2994.99 BogoMIPS).
  148. NET: Registered protocol family 16
  149. L310 cache controller enabled
  150. l2x0: 8 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x42540001
  151. bio: create slab <bio-0> at 0
  152. vgaarb: loaded
  153. SCSI subsystem initialized
  154. usbcore: registered new interface driver usbfs
  155. usbcore: registered new interface driver hub
  156. usbcore: registered new device driver usb
  157. Switching to clocksource timer1
  158. NET: Registered protocol family 2
  159. IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
  160. TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  161. TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
  162. TCP: Hash tables configured (established 16384 bind 16384)
  163. TCP reno registered
  164. UDP hash table entries: 256 (order: 1, 8192 bytes)
  165. UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  166. NET: Registered protocol family 1
  167. sb_phy_program: is_24mhz=1, phy_number=0
  168. sb_phy_program_24mhz: base_addr + 32 = 0x68a00000
  169. sb_phy_program_24mhz: base_addr + 96 = 0x5e080600
  170. sb_phy_program_24mhz: base_addr + 100 = 0xf0914200
  171. sb_phy_program_24mhz: base_addr + 128 = 0xe0
  172. sb_phy_program: is_24mhz=1, phy_number=1
  173. sb_phy_program_24mhz: base_addr + 32 = 0x68a00000
  174. sb_phy_program_24mhz: base_addr + 96 = 0x5e080600
  175. sb_phy_program_24mhz: base_addr + 100 = 0xf0914200
  176. sb_phy_program_24mhz: base_addr + 128 = 0xe0
  177. sb_phy_program: is_24mhz=1, phy_number=2
  178. sb_phy_program_24mhz: base_addr + 32 = 0x68a00000
  179. sb_phy_program_24mhz: base_addr + 96 = 0x5e080600
  180. sb_phy_program_24mhz: base_addr + 100 = 0xf0914200
  181. sb_phy_program_24mhz: base_addr + 128 = 0xe0
  182. setup_io_mux: gpio_num=2, gpio_pin=28, gpio_value=0x10000000, gpio_mux=0xf0000024, gpio_out=0xf0070214, gpio_cfg=0xf0070210, not gpio_value=0xefffffff
  183. g2_pcie_link_up: rc number 0 link up!!!
  184. g2_pcie_link_up: rc number 1 link up!!!
  185. g2_pcie_link_up: rc number 2 link up!!!
  186. g2_pcie_setup: NUM_PCIE_PORTS=3, num_port_sb_phy=3, nr=0, sys->busnr=0
  187. g2_pcie_setup: MEM.name=PCIe 0 MEM, MEM.start=0x802fffff, MEM.end=0x9fffffff, MEM.flags=0x200
  188. g2_pcie_setup: IO.name=PCIe 0 BASE address, IO.start=0x80100000, IO.end=0x801fffff, IO.flags=0x100
  189. PCI: bus0: Fast back to back transfers disabled
  190. g2_pcie_rd_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  191. g2_pcie_rd_conf: bsu number=1, devfn=0x0, PCI_SUBSYSTEM_VENDOR_ID=0x3223168c
  192. g2_pcie_rd_conf: read from RC, val=0xff, devfn=0, where=60, bus->number=1
  193. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  194. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  195. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  196. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  197. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  198. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  199. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  200. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  201. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  202. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  203. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  204. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  205. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  206. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  207. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  208. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  209. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  210. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  211. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  212. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  213. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  214. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  215. g2_pcie_rd_conf: read from RC, val=0x0, devfn=0, where=48, bus->number=1
  216. g2_pcie_rd_conf: read from RC, val=0xffff0000, devfn=0, where=48, bus->number=1
  217. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  218. g2_pcie_wr_conf: val=0x0, devfn=0, where=4, bus->number=1
  219. g2_pcie_wr_conf: bsu number=1, PCI Configuration space PCI_HEADER_TYPE=0x0
  220. g2_pcie_wr_conf: val=0x140, devfn=0, where=4, bus->number=1
  221. PCI: bus1: Fast back to back transfers disabled
  222. g2_pcie_setup: NUM_PCIE_PORTS=3, num_port_sb_phy=3, nr=1, sys->busnr=2
  223. g2_pcie_setup: MEM.name=PCIe 1 MEM, MEM.start=0xa02fffff, MEM.end=0xbfffffff, MEM.flags=0x200
  224. g2_pcie_setup: IO.name=PCIe 1 BASE address, IO.start=0xa0100000, IO.end=0xa01fffff, IO.flags=0x100
  225. PCI: bus2: Fast back to back transfers disabled
  226. g2_pcie_rd_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  227. g2_pcie_rd_conf: bsu number=3, devfn=0x0, PCI_SUBSYSTEM_VENDOR_ID=0x3123168c
  228. g2_pcie_rd_conf: read from RC, val=0xff, devfn=0, where=60, bus->number=3
  229. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  230. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  231. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  232. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  233. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  234. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  235. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  236. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  237. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  238. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  239. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  240. g2_pcie_rd_conf: read from RC, val=0x0, devfn=0, where=48, bus->number=3
  241. g2_pcie_rd_conf: read from RC, val=0xffff0000, devfn=0, where=48, bus->number=3
  242. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  243. g2_pcie_wr_conf: bsu number=3, PCI Configuration space PCI_HEADER_TYPE=0x0
  244. PCI: bus3: Fast back to back transfers disabled
  245. g2_pcie_setup: NUM_PCIE_PORTS=3, num_port_sb_phy=3, nr=2, sys->busnr=4
  246. g2_pcie_setup: MEM.name=PCIe 2 MEM, MEM.start=0xc02fffff, MEM.end=0xdfffffff, MEM.flags=0x200
  247. g2_pcie_setup: IO.name=PCIe 2 BASE address, IO.start=0xc0100000, IO.end=0xc01fffff, IO.flags=0x100
  248. PCI: bus4: Fast back to back transfers disabled
  249. g2_pcie_rd_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  250. g2_pcie_rd_conf: bsu number=5, devfn=0x0, PCI_SUBSYSTEM_VENDOR_ID=0x11421b21
  251. g2_pcie_rd_conf: read from RC, val=0x0, devfn=0, where=60, bus->number=5
  252. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  253. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  254. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  255. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  256. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  257. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  258. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  259. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  260. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  261. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  262. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  263. g2_pcie_rd_conf: read from RC, val=0x0, devfn=0, where=48, bus->number=5
  264. g2_pcie_rd_conf: read from RC, val=0x0, devfn=0, where=48, bus->number=5
  265. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  266. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  267. PCI: bus5: Fast back to back transfers disabled
  268. pcie_find_free_irq: interrupt pin of bus=1, devfn=0x0 is 1
  269. g2_pcie_map_irq: call set_irq_chip_and_handler(), interrupt_pin=1
  270. g2_pcie_map_irq: is a EP, irq=96, sys->busnr=0
  271. pcie_find_free_irq: interrupt pin of bus=3, devfn=0x0 is 1
  272. g2_pcie_map_irq: call set_irq_chip_and_handler(), interrupt_pin=1
  273. g2_pcie_map_irq: is a EP, irq=97, sys->busnr=2
  274. pcie_find_free_irq: interrupt pin of bus=5, devfn=0x0 is 1
  275. g2_pcie_map_irq: call set_irq_chip_and_handler(), interrupt_pin=1
  276. g2_pcie_map_irq: is a EP, irq=98, sys->busnr=4
  277. pci 0000:04:00.0: BAR 8: assigned [mem 0xc0300000-0xc03fffff]
  278. pci 0000:05:00.0: BAR 0: assigned [mem 0xc0300000-0xc0307fff 64bit]
  279. pci 0000:05:00.0: BAR 0: set to [mem 0xc0300000-0xc0307fff 64bit] (PCI address [0xc0300000-0xc0307fff]
  280. pci 0000:04:00.0: PCI bridge to [bus 05-05]
  281. pci 0000:04:00.0:   bridge window [io  disabled]
  282. pci 0000:04:00.0:   bridge window [mem 0xc0300000-0xc03fffff]
  283. pci 0000:04:00.0:   bridge window [mem pref disabled]
  284. pci 0000:02:00.0: BAR 8: assigned [mem 0xa0300000-0xa03fffff]
  285. pci 0000:02:00.0: BAR 9: assigned [mem 0xa0400000-0xa04fffff pref]
  286. pci 0000:03:00.0: BAR 0: assigned [mem 0xa0300000-0xa031ffff 64bit]
  287. pci 0000:03:00.0: BAR 0: set to [mem 0xa0300000-0xa031ffff 64bit] (PCI address [0xa0300000-0xa031ffff]
  288. pci 0000:03:00.0: BAR 6: assigned [mem 0xa0400000-0xa040ffff pref]
  289. pci 0000:02:00.0: PCI bridge to [bus 03-03]
  290. pci 0000:02:00.0:   bridge window [io  disabled]
  291. pci 0000:02:00.0:   bridge window [mem 0xa0300000-0xa03fffff]
  292. pci 0000:02:00.0:   bridge window [mem 0xa0400000-0xa04fffff pref]
  293. pci 0000:00:00.0: BAR 8: assigned [mem 0x80400000-0x805fffff]
  294. pci 0000:00:00.0: BAR 9: assigned [mem 0x80300000-0x803fffff pref]
  295. pci 0000:01:00.0: BAR 0: assigned [mem 0x80400000-0x805fffff 64bit]
  296. pci 0000:01:00.0: BAR 0: set to [mem 0x80400000-0x805fffff 64bit] (PCI address [0x80400000-0x805fffff]
  297. pci 0000:01:00.0: BAR 6: assigned [mem 0x80300000-0x8030ffff pref]
  298. pci 0000:00:00.0: PCI bridge to [bus 01-01]
  299. pci 0000:00:00.0:   bridge window [io  disabled]
  300. pci 0000:00:00.0:   bridge window [mem 0x80400000-0x805fffff]
  301. pci 0000:00:00.0:   bridge window [mem 0x80300000-0x803fffff pref]
  302. g2_pcie_init, set the PCIe interrupt to CPU0 only
  303. VFS: Disk quotas dquot_6.5.2
  304. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  305. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  306. Registering mini_fo version $Id$
  307. JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  308. fuse init (API version 7.15)
  309. msgmni has been set to 838
  310. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
  311. io scheduler noop registered
  312. io scheduler deadline registered
  313. io scheduler cfq registered (default)
  314.  
  315. cs75xx_gpio_init
  316. Function: cs75xx_gpio_probe, pdev->name = cs75xx_gpio
  317.         cs75xx_global_base = 9c824000
  318.         cs75xx_gpio_base[0] = 9c8841d0
  319.         cs75xx_gpio_base[1] = 9c8881f0
  320.         cs75xx_gpio_base[2] = 9c88c210
  321.         cs75xx_gpio_base[3] = 9c890230
  322.         cs75xx_gpio_base[4] = 9c894250
  323.         cs75xx_irq_gpio[0] = 00000056
  324.         cs75xx_irq_gpio[1] = 00000057
  325.         cs75xx_irq_gpio[2] = 00000058
  326.         cs75xx_irq_gpio[3] = 00000059
  327.         cs75xx_irq_gpio[4] = 0000005a
  328. , rc = 0
  329. i2c /dev entries driver
  330. WRNG: I2C SCL set to 1000000KHz!
  331. cs75xx-spi cs75xx-spi: at (mapped) 0x9C89C064, bus 0
  332. Debug:...Clearing memory....
  333. cs75xx_trng cs75xx_trng.0: Function: cs75xx_trng_probe, pdev->name = cs75xx_trng
  334. Cortina on-chip UART init.
  335. ttyS0 at I/O 0x0 (irq = 38) is a Cortina UART
  336. ttyS1 at I/O 0x0 (irq = 39) is a Cortina UART
  337. ttyS2 at I/O 0x0 (irq = 40) is a Cortina UART
  338. ttyS3 at I/O 0x0 (irq = 41) is a Cortina UART
  339. brd: module loaded
  340. loop: module loaded
  341. SCSI Media Changer driver v0.25
  342. ahci: SSS flag set, parallel bus scan disabled
  343. goldengate-ahci goldengate-ahci.0: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x8 impl SATA mode
  344. goldengate-ahci goldengate-ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
  345. scsi0 : goldengate-ahci
  346. scsi1 : goldengate-ahci
  347. scsi2 : goldengate-ahci
  348. scsi3 : goldengate-ahci
  349. ata1: DUMMY
  350. ata2: DUMMY
  351. ata3: DUMMY
  352. ata4: SATA max UDMA/133 irq 64
  353. cs752x_nand_init : Flash type : 0x5400
  354. --> cs752x_nand_init
  355. CS752X NAND init ...
  356. Error Correction Method: ecc 256
  357. NAND device: Manufacturer ID: 0x01, Chip ID: 0xdc (AMD NAND 512MiB 3,3V 8-bit)
  358. Scanning device for bad blocks
  359. Checking for command line partitions ...
  360. 14 cmdlinepart partitions found on MTD device cs752x_nand_flash
  361. Creating 14 MTD partitions on "cs752x_nand_flash":
  362. 0x000000100000-0x000000200000 : "uboot-env0"
  363. 0x000000300000-0x000000400000 : "uboot-env1"
  364. 0x000000400000-0x000000500000 : "sb0"
  365. 0x000000500000-0x000000600000 : "sb1"
  366. 0x000000c00000-0x000003a00000 : "rootfs"
  367. ata4: SATA link down (SStatus 0 SControl 300)
  368. mtd: partition "rootfs" set to be root filesystem
  369. 0x000003a00000-0x000004000000 : "kernel_standby"
  370. 0x000004000000-0x000006e00000 : "rootfs_standby"
  371. 0x000006e00000-0x000007e00000 : "rootfs_data"
  372. 0x000007e00000-0x000007f00000 : "log"
  373. 0x000007f00000-0x000008000000 : "cal"
  374. 0x000008000000-0x000008100000 : "man"
  375. 0x000008100000-0x000008600000 : "Almond_Data"
  376. 0x000000020000-0x000000100000 : "uboot0"
  377. 0x000000200000-0x000000300000 : "uboot1"
  378. cx752x NAND init ok...
  379. CS75xx Gigabit Ethernet driver0.2.1 built at Jun 25 2014 15:19:29
  380. MAC0: xx:xx:xx:xx:xx:xx
  381. MAC1: xx:xx:xx:xx:xx:xx
  382. MAC2: xx:xx:xx:xx:xx:xx
  383. Use external DDR for QM
  384. vtable_setup_def_hashmask Err in create 6 hash tuples at vtable_type=8 (need 5)
  385. vtable_setup_def_hashmask Err in create 6 hash tuples at vtable_type=9 (need 5)
  386. vtable_setup_def_hashmask Err in create 6 hash tuples at vtable_type=10 (need 5)
  387. vtable_setup_def_hashmask Err in create 6 hash tuples at vtable_type=11 (need 5)
  388. cs75xx_mdiobus: probed
  389. eth0: PHY Default mode NI_MAC_PHY_RGMII_1000 at addr 0
  390. GE-0: attached PHY driver [Generic PHY] (mdio_bus:phy_addr=0:00, id=0x004dd036)
  391. eth0: link up, speed 1000 Mb/s, full duplex
  392. ----> GE-0: phy_id 0x004dd036
  393. eth1: link up, speed 1000 Mb/s, full duplex
  394. cs75xx_mdiobus: probed
  395. eth2: no PHY found
  396. ----> GE-2: phy_id 0xffffffff
  397. G2 default proc value:
  398.         cs_rt3593_noncache=0
  399.         cs_ni_fastbridge=0
  400. cs_wfo_mc_mac_table_init
  401. Set callback 00000001 at pos 3
  402. Set callback 00000001 at pos 4
  403. Set callback 00000001 at pos 5
  404. Set callback 00000001 at pos 6
  405. Set callback 00000001 at pos 14
  406. Set callback 00000001 at pos 1
  407. Set callback 00000001 at pos 8
  408. ipsec_ipc_register::successfully register IPC for RE0
  409. ipsec_ipc_register::successfully register IPC for RE1
  410. Set callback 00000001 at pos 10
  411. Set callback 00000001 at pos 12
  412. Set callback 00000001 at pos 15
  413. cs_iplip_ipc_register::successfully register IPC for CS tunnel acceleration
  414. Set callback 00000001 at pos 16
  415. Set callback 00000001 at pos 17
  416. PPP generic driver version 2.4.2
  417. PPP MPPE Compression module registered
  418. NET: Registered protocol family 24
  419. IMQ driver loaded successfully.
  420.         Hooking IMQ before NAT on PREROUTING.
  421.         Hooking IMQ after NAT on POSTROUTING.
  422. usbcore: registered new interface driver cdc_ether
  423. usbcore: registered new interface driver cdc_eem
  424. usbcore: registered new interface driver rndis_host
  425. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  426. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  427. PCI: enabling device 0000:05:00.0 (0140 -> 0142)
  428. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  429. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  430. xhci_hcd 0000:05:00.0: xHCI Host Controller
  431. xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 1
  432. g2_pcie_rd_conf: read from RC, val=0x8, devfn=0, where=12, bus->number=5
  433. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  434. unmask_intx_irq: irq=98, bus_number=4
  435. xhci_hcd 0000:05:00.0: irq 98, io mem 0xc0300000
  436. mask_intx_irq: irq=98, bus_number=4
  437. g2_pcie_wr_conf: bsu number=5, PCI Configuration space PCI_HEADER_TYPE=0x0
  438. usb usb1: New USB device found, idVendor=1d6b, idProduct=0003
  439. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  440. usb usb1: Product: xHCI Host Controller
  441. usb usb1: Manufacturer: Linux 2.6.36 xhci_hcd
  442. usb usb1: SerialNumber: 0000:05:00.0
  443. hub 1-0:1.0: USB hub found
  444. hub 1-0:1.0: 2 ports detected
  445. xhci_hcd 0000:05:00.0: xHCI Host Controller
  446. xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 2
  447. usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
  448. usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  449. usb usb2: Product: xHCI Host Controller
  450. usb usb2: Manufacturer: Linux 2.6.36 xhci_hcd
  451. usb usb2: SerialNumber: 0000:05:00.0
  452. hub 2-0:1.0: USB hub found
  453. hub 2-0:1.0: 2 ports detected
  454. usbcore: registered new interface driver cdc_acm
  455. cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
  456. usbcore: registered new interface driver usblp
  457. Initializing USB Mass Storage driver...
  458. usbcore: registered new interface driver usb-storage
  459. USB Mass Storage support registered.
  460. usbcore: registered new interface driver ums-datafab
  461. usbcore: registered new interface driver ums-freecom
  462. usbcore: registered new interface driver ums-isd200
  463. usbcore: registered new interface driver ums-sddr09
  464. usbcore: registered new interface driver ums-sddr55
  465. usbcore: registered new interface driver ums-usbat
  466. usbcore: registered new interface driver usbserial
  467. USB Serial support registered for generic
  468. usbcore: registered new interface driver usbserial_generic
  469. usbserial: USB Serial Driver core
  470. USB Serial support registered for cp210x
  471. usbcore: registered new interface driver cp210x
  472. cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
  473. USB Serial support registered for FTDI USB Serial Device
  474. usbcore: registered new interface driver ftdi_sio
  475. ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
  476. USB Serial support registered for GSM modem (1-port)
  477. usbcore: registered new interface driver option
  478. option: v0.7.2:USB Driver for GSM modems
  479. mice: PS/2 mouse device common for all mice
  480. input: gpio-keys as /devices/platform/gpio-keys/input/input0
  481. input: gpio-buttons as /devices/platform/gpio-buttons/input/input1
  482. G2 Watchdog Timer: 0.1. g2_noboot=0 g2_margin=30 sec (nowayout= 0)
  483. g2_wdt_probe: base address =9c8ac600  IRQ=30...
  484. gpio init done
  485. almond_touch_major = 97
  486. almond_touch_major = 251
  487. ---------------------sx8650 driver probe----------------------
  488. sx8650 0-0048: sx8650_probe()
  489. i2c i2c-0: cs75xx_i2c_fsm: Ctlr Error -- state: 0x0, ack: 0x6, addr: 0x48, flags: 0x0, left: 0x1
  490. WRNG: I2C SCL set to 1000000KHz!
  491. input: SX8650 Touchscreen as /devices/virtual/input/input2
  492. sx8650 0-0048: registered with irq (311)
  493. Button Hotplug driver version 0.4.1
  494. Link Driver Device Major Number = 35
  495. Mirror/redirect action on
  496. u32 classifier
  497.     Performance counters on
  498.     input device check on
  499.     Actions configured
  500. Netfilter messages via NETLINK v0.30.
  501. nf_conntrack version 0.5.0 (6705 buckets, 26820 max)
  502. ctnetlink v0.93: registering with nfnetlink.
  503. NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  504. NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  505. xt_time: kernel timezone is -0000
  506. IPv4 over IPv4 tunneling driver
  507. GRE over IPv4 tunneling driver
  508. ip_tables: (C) 2000-2006 Netfilter Core Team
  509. ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
  510. arp_tables: (C) 2002 David S. Miller
  511. TCP cubic registered
  512. Initializing XFRM netlink socket
  513. NET: Registered protocol family 10
  514. lo: Disabled Privacy Extensions
  515. tunl0: Disabled Privacy Extensions
  516. ip6_tables: (C) 2000-2006 Netfilter Core Team
  517. IPv6 over IPv4 tunneling driver
  518. sit0: Disabled Privacy Extensions
  519. ip6tnl0: Disabled Privacy Extensions
  520. NET: Registered protocol family 17
  521. NET: Registered protocol family 15
  522. Bridge firewalling registered
  523. Ebtables v2.0 registered
  524. L2TP core driver, V2.0
  525. PPPoL2TP kernel driver, V2.0
  526. L2TP netlink interface
  527. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  528. All bugs added by David S. Miller <davem@redhat.com>
  529. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
  530. VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  531. Freeing init memory: 192K
  532. - preinit -
  533. Press the [f] key and hit [enter] to enter failsafe mode
  534. - regular preinit -
  535. switching to jffs2
  536. mini_fo: using base directory: /
  537. mini_fo: using storage directory: /overlay
  538. - init -
  539.  
  540. (none) login: root
  541. Password:
  542. Jan  1 00:00:21 login[1144]: root login on 'ttyS0'
  543.  
  544.  
  545. BusyBox v1.17.3 (2014-07-10 12:15:02 IST) built-in shell (ash)
  546. Enter 'help' for a list of built-in commands.
  547.  
  548.  ______   _      __  __   _____   __   _   ____       __
  549. |  __  | | |    |  \/  | |  _  | |  \ | | |  _ \   __|  |__
  550. | |__| | | |    |      | | | | | |   \| | | | \ \ |        |
  551. |  __  | | |__  | |\/| | | |_| | | |\   | | |_/ / |__    __|
  552. |_|  |_| |____| |_|  |_| |_____| |_| \__| |____/     |__|
  553.  
  554. S E C U R I F I  Home Automation
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top