Texas Instruments X-Loader 1.4.4ss (Oct 17 2010 - 20:14:00)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2010.03 (Aug 06 2010 - 11:28:56)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max clock-720Mhz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  256 MB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial

Probing for expansion boards, if none are connected you'll see a harmless I2C error.

timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Unrecognized expansion board: 0
Beagle Rev C4
Die ID #249000040000000004037f660901b002
Hit any key to stop autoboot:  0
mmc1 is available
reading uImage

3216328 bytes read
## Booting kernel from Legacy Image at 80300000 ...
   Image Name:   Linux-2.6.32
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3216264 Bytes =  3.1 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.................................................................................................................................................................
[    0.000000] Linux version 2.6.32 (koen@dominion) (gcc version 4.3.3 (GCC) ) #2 PREEMPT Sun Oct 17 19:40:25 CEST 2010
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: OMAP3 Beagle Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m )
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[    0.000000] Reserving 14680064 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw rootwait
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 128MB 128MB = 256MB total
[    0.000000] Memory: 238336KB available (5928K code, 673K data, 220K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[    0.000000] Reprogramming SDRC clock to 332000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 465.31 BogoMIPS (lpj=1818624)
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] tmpfs: No value for mount option 'mode'
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] Found NAND on CS0
[    0.000000] Registering NAND on CS0
[    0.000000] Unable to get DVI reset GPIO
[   19.179138] OMAP DMA hardware revision 4.0
[   19.188293] bio: create slab <bio-0> at 0
[   19.189941] SCSI subsystem initialized
[   19.191741] usbcore: registered new interface driver usbfs
[   19.191986] usbcore: registered new interface driver hub
[   19.192291] usbcore: registered new device driver usb
[   19.192779] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
[   19.196014] twl4030: PIH (irq 7) chaining IRQs 368..375
[   19.196075] twl4030: power (irq 373) chaining IRQs 376..383
[   19.196502] twl4030: gpio (irq 368) chaining IRQs 384..401
[   19.198242] regulator: VUSB1V5: 1500 mV normal standby
[   19.198577] regulator: VUSB1V8: 1800 mV normal standby
[   19.198913] regulator: VUSB3V1: 3100 mV normal standby
[   19.200469] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[   19.201049] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[   19.201446] regulator: VDAC: 1800 mV normal standby
[   19.201782] regulator: VPLL2: 1800 mV normal standby
[   19.202148] regulator: VSIM: 1800 <--> 3000 mV normal standby
[   19.202636] regulator: VAUX3: 1800 mV normal standby
[   19.203063] regulator: VAUX4: 1800 mV normal standby
[   19.203308] i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz
[   19.203613] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
[   19.205566] Switching to clocksource 32k_counter
[   19.218353] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[   19.221466] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[   19.221527] musb_hdrc musb_hdrc: MUSB HDRC host driver
[   19.221710] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[   19.221923] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   19.221984] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   19.222045] usb usb1: Product: MUSB HDRC host driver
[   19.222106] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[   19.222167] usb usb1: SerialNumber: musb_hdrc
[   19.222991] hub 1-0:1.0: USB hub found
[   19.223052] hub 1-0:1.0: 1 port detected
[   19.224365] NET: Registered protocol family 2
[   19.224670] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[   19.225372] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[   19.225677] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[   19.225860] TCP: Hash tables configured (established 8192 bind 8192)
[   19.225921] TCP reno registered
[   19.225952] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   19.226043] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   19.226379] NET: Registered protocol family 1
[   19.226959] RPC: Registered udp transport module.
[   19.226989] RPC: Registered tcp transport module.
[   19.227050] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   19.228240] omap-iommu omap-iommu.0: isp registered
[   19.230529] VFS: Disk quotas dquot_6.5.2
[   19.230682] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.232086] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   19.233154] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
[   19.234252] msgmni has been set to 465
[   19.239776] alg: No test for stdrng (krng)
[   19.240173] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[   19.240264] io scheduler noop registered
[   19.240295] io scheduler deadline registered
[   19.240509] io scheduler cfq registered (default)
[   19.299621] OMAP DSS rev 2.0
[   19.299713] OMAP DISPC rev 3.0
[   19.299804] OMAP VENC rev 2
[   19.300140] OMAP DSI rev 1.0
[   19.640411] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   19.660675] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[   19.679992] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[   19.699310] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[   20.232238] console [ttyS2] enabled
[   20.244720] brd: module loaded
[   20.252136] loop: module loaded
[   20.258178] omap2-nand driver initializing
[   20.262695] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
[   20.271972] cmdlinepart partition parsing not available
[   20.277343] Creating 5 MTD partitions on "omap2-nand":
[   20.282531] 0x000000000000-0x000000080000 : "X-Loader"
[   20.289215] 0x000000080000-0x000000260000 : "U-Boot"
[   20.295928] 0x000000260000-0x000000280000 : "U-Boot Env"
[   20.302307] 0x000000280000-0x000000680000 : "Kernel"
[   20.309844] 0x000000680000-0x000010000000 : "File System"
[   20.415557] usbcore: registered new interface driver catc
[   20.421112] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[   20.427246] usbcore: registered new interface driver kaweth
[   20.432922] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[   20.440643] usbcore: registered new interface driver pegasus
[   20.446380] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[   20.453491] usbcore: registered new interface driver rtl8150
[   20.459381] usbcore: registered new interface driver asix
[   20.464965] usbcore: registered new interface driver cdc_ether
[   20.471008] usbcore: registered new interface driver dm9601
[   20.476806] usbcore: registered new interface driver smsc95xx
[   20.482788] usbcore: registered new interface driver gl620a
[   20.488586] usbcore: registered new interface driver net1080
[   20.494445] usbcore: registered new interface driver plusb
[   20.500122] usbcore: registered new interface driver rndis_host
[   20.506256] usbcore: registered new interface driver cdc_subset
[   20.512390] usbcore: registered new interface driver zaurus
[   20.518157] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[   20.526550] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   20.533477] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[   20.539642] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[   20.547363] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[   20.565124] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[   20.571075] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   20.578002] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   20.585357] usb usb2: Product: OMAP-EHCI Host Controller
[   20.590759] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[   20.596282] usb usb2: SerialNumber: ehci-omap.0
[   20.601715] hub 2-0:1.0: USB hub found
[   20.605621] hub 2-0:1.0: 3 ports detected
[   20.635559] Initializing USB Mass Storage driver...
[   20.640686] usbcore: registered new interface driver usb-storage
[   20.646820] USB Mass Storage support registered.
[   20.651611] g_ether gadget: using random self ethernet address
[   20.657531] g_ether gadget: using random host ethernet address
[   20.664001] usb0: MAC a6:21:78:83:29:4e
[   20.667968] usb0: HOST MAC c6:32:1a:d3:bb:ba
[   20.672332] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[   20.679077] g_ether gadget: g_ether ready
[   20.683654] mice: PS/2 mouse device common for all mice
[   20.689422] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   20.697570] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[   20.708465] i2c /dev entries driver
[   20.712829] Linux video capture interface: v2.00
[   20.717895] omap-iommu omap-iommu.0: isp: version 1.1
[   20.724822] vpfe_init
[   20.727813] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[   20.734893] cpuidle: using governor ladder
[   20.739135] cpuidle: using governor menu
[   20.854522] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[   20.861663] Registered led device: beagleboard::usr0
[   20.866882] Registered led device: beagleboard::usr1
[   20.873107] Registered led device: beagleboard::pmu_stat
[   20.881011] usbcore: registered new interface driver usbhid
[   20.886718] usbhid: USB HID core driver
[   20.890808] Advanced Linux Sound Architecture Driver Version 1.0.21.
[   20.897949] usbcore: registered new interface driver snd-usb-audio
[   20.987396] No device for DAI omap-mcbsp-dai-0
[   20.991912] No device for DAI omap-mcbsp-dai-1
[   20.996459] No device for DAI omap-mcbsp-dai-2
[   21.000946] No device for DAI omap-mcbsp-dai-3
[   21.005493] No device for DAI omap-mcbsp-dai-4
[   21.009979] OMAP3 Beagle SoC init
[   21.015167] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[   21.028564] ALSA device list:
[   21.031585]   #0: omap3beagle (twl4030)
[   21.035644] oprofile: using arm/armv7
[   21.039642] TCP cubic registered
[   21.042968] NET: Registered protocol family 17
[   21.047515] NET: Registered protocol family 15
[   21.052185] lib80211: common routines for IEEE802.11 drivers
[   21.058013] ThumbEE CPU extension supported.
[   21.062316] Power Management for TI OMAP3.
[   21.068084] SmartReflex driver initialized
[   21.085357] ------------[ cut here ]------------
[   21.090057] WARNING: at arch/arm/mach-omap2/dpll.c:439 omap3_noncore_dpll_set_rate+0x228/0x26c()
[   21.098907] Modules linked in:
[   21.102050] [<c0044cb0>] (unwind_backtrace+0x0/0xdc) from [<c0071728>] (warn_slowpath_common+0x4c/0x80)
[   21.111541] [<c0071728>] (warn_slowpath_common+0x4c/0x80) from [<c004f288>] (omap3_noncore_dpll_set_rate+0x228/0x26c)
[   21.122253] [<c004f288>] (omap3_noncore_dpll_set_rate+0x228/0x26c) from [<c004d83c>] (omap2_clk_set_rate+0x24/0x34)
[   21.132812] [<c004d83c>] (omap2_clk_set_rate+0x24/0x34) from [<c0055654>] (clk_set_rate+0x4c/0xbc)
[   21.141876] [<c0055654>] (clk_set_rate+0x4c/0xbc) from [<c0053298>] (program_opp+0xe0/0x180)
[   21.150390] [<c0053298>] (program_opp+0xe0/0x180) from [<c0053428>] (resource_set_opp_level+0xf0/0x16c)
[   21.159881] [<c0053428>] (resource_set_opp_level+0xf0/0x16c) from [<c00534e0>] (set_opp+0x3c/0x100)
[   21.169036] [<c00534e0>] (set_opp+0x3c/0x100) from [<c005d9e4>] (update_resource_level+0xa8/0xcc)
[   21.178009] [<c005d9e4>] (update_resource_level+0xa8/0xcc) from [<c0053190>] (set_freq+0x110/0x138)
[   21.187133] [<c0053190>] (set_freq+0x110/0x138) from [<c005d9e4>] (update_resource_level+0xa8/0xcc)
[   21.196289] [<c005d9e4>] (update_resource_level+0xa8/0xcc) from [<c005cad0>] (omap_target+0x5c/0x78)
[   21.205505] [<c005cad0>] (omap_target+0x5c/0x78) from [<c038ca60>] (__cpufreq_driver_target+0x5c/0x78)
[   21.214935] [<c038ca60>] (__cpufreq_driver_target+0x5c/0x78) from [<c038e868>] (cpufreq_governor_performance+0x48/0x5c)
[   21.225830] [<c038e868>] (cpufreq_governor_performance+0x48/0x5c) from [<c038c77c>] (__cpufreq_governor+0x160/0x1bc)
[   21.236450] [<c038c77c>] (__cpufreq_governor+0x160/0x1bc) from [<c038d634>] (__cpufreq_set_policy+0x190/0x220)
[   21.246551] [<c038d634>] (__cpufreq_set_policy+0x190/0x220) from [<c038ddb8>] (cpufreq_add_dev+0x3ec/0x584)
[   21.256408] [<c038ddb8>] (cpufreq_add_dev+0x3ec/0x584) from [<c02bfc48>] (sysdev_driver_register+0xb0/0x120)
[   21.266326] [<c02bfc48>] (sysdev_driver_register+0xb0/0x120) from [<c038c914>] (cpufreq_register_driver+0x110/0x200)
[   21.276977] [<c038c914>] (cpufreq_register_driver+0x110/0x200) from [<c003f384>] (do_one_initcall+0x5c/0x1bc)
[   21.286987] [<c003f384>] (do_one_initcall+0x5c/0x1bc) from [<c0008414>] (kernel_init+0xa4/0x128)
[   21.295867] [<c0008414>] (kernel_init+0xa4/0x128) from [<c00409fc>] (kernel_thread_exit+0x0/0x8)
[   21.304779] ---[ end trace 11aaf61cca1e0961 ]---
[   21.309692] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[   21.318115] registered taskstats version 1
[   21.339447] Console: switching to colour frame buffer device 80x30
[   21.357849] regulator_init_complete: incomplete constraints, leaving VAUX3 on
[   21.365295] regulator_init_complete: incomplete constraints, leaving VDAC on
[   21.372894] omap_vout omap_vout: probed for an unknown device
[   21.379180] Waiting for root device /dev/mmcblk0p2...
[   21.535278] mmc0: new high speed SD card at address 0002
[   21.541107] mmcblk0: mmc0:0002 SN02G 1.87 GiB
[   21.545989]  mmcblk0: p1 p2
[   27.559509] kjournald starting.  Commit interval 5 seconds
[   27.568664] EXT3-fs (mmcblk0p2): using internal journal
[   27.574005] EXT3-fs (mmcblk0p2): recovery complete
[   27.588897] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
[   27.596130] VFS: Mounted root (ext3 filesystem) on device 179:2.
[   27.606323] devtmpfs: mounted
[   27.609375] Freeing init memory: 220K
INIT: version 2.86 booting
/etc/rcS.d/S01psplash: .: line 8: can't open /etc/init.d/functions
Caching udev devnodes
Populating dev cachemv: cannot rename '/tmp/uname': No such file or directory
[   28.508392] Bluetooth: Core ver 2.15
[   28.512329] NET: Registered protocol family 31
[   28.516815] Bluetooth: HCI device and connection manager initialized
[   28.523284] Bluetooth: HCI socket layer initialized
[   28.547027] Bluetooth: L2CAP ver 2.14
[   28.550811] Bluetooth: L2CAP socket layer initialized
[   28.574127] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   28.716186] NET: Registered protocol family 10
[   28.757476] Bluetooth: RFCOMM TTY layer initialized
[   28.762573] Bluetooth: RFCOMM socket layer initialized
[   28.767761] Bluetooth: RFCOMM ver 1.11
ALSA: Restoring mixer settings...
Configuring network interfaces... ifup: interface lo already configured
ifup: interface eth0 already configured
ifup: interface usb0 already configured
done.
Starting portmap daemon: portmap.
INIT: Entering runlevel: 5
Removing stale PID file /var/run/dbus/pid.
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
run-parts: /etc/dbus-1/event.d/20hal exited with code 2
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
Starting internet superserver: xinetd.
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
Process 228 died: No such process; trying to remove PID file. (/var/run/avahi-daemon//pid)
   ...done.
Starting Network connection manager daemon: NetworkManager.
Starting GNOME Display Manager gdm

.-------.
|       |                  .-.
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyS2

Angstrom 2010.7-test-20101105 beagleboard ttyS2

鰊[  �������8��]