Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Apr 7 2011 - 15:42:54)
- Board: Ralink APSoC DRAM: 16 MB
- relocate_code Pointer at: 80fac000
- mips_cpu_feq=320000000
- The Flash ID =000022CB
- vender : MX_MANUFACT
- MX_ID_29LV640DB, Size = 00800000 bytes
- flash_protect ON: from 0xBF000000 to 0xBF020A47
- protect on 0
- protect on 1
- protect on 2
- protect on 3
- protect on 4
- protect on 5
- protect on 6
- protect on 7
- protect on 8
- protect on 9
- flash_protect ON: from 0xBF030000 to 0xBF03FFFF
- protect on 10
- *** Warning - bad CRC, using default environment
- ============================================
- ZTE UBoot Version: 1.0.1
- --------------------------------------------
- ASIC 3052_MP2 (Port5<->None)
- DRAM COMPONENT: 128Mbits
- DRAM BUS: 16BIT
- Total memory: 16 MBytes
- Date:Apr 7 2011 Time:15:42:54
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- freq = 320000000 MHZ
- ##### The CPU freq = 320 MHZ ####
- SDRAM bus set to 16 bit
- SDRAM size =16 Mbytes
- PHY0 and PHY1 are used ,and other PHYS are powered down
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- ^H^H^H 0
- 3: System Boot system code via Flash.
- ## Booting image at bf050000 ...
- Image Name: Linux Kernel Image
- Created: 2011-07-13 9:09:23 UTC
- System Control Status = 0x00400000
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 3731392 Bytes = 3.6 MB
- Load Address: 80000000
- Entry Point: 80312000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80312000) ...
- ## Giving linux memsize in MB, 16
- Starting kernel ...
- LINUX started...
- THIS IS ASIC
- Linux version 2.6.21 (renb@localhost.localdomain) (gcc version 3.4.2) #57 Mon Jul 11 19:20:27 CST 2011
- The CPU feqenuce set to 320 MHz
- CPU revision is: 0001964c
- Determined physical RAM map:
- memory: 01000000 @ 00000000 (usable)
- Built 1 zonelists. Total pages: 4064
- Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock4
- Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
- Primary data cache 16kB, 4-way, linesize 32 bytes.
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- Cache parity protection disabled
- cause = 80800074, status = 1100ff00
- PID hash table entries: 64 (order: 6, 256 bytes)
- calculating r4koff... 00138800(1280000)
- CPU frequency 320.00 MHz
- Using 160.000 MHz high precision timer.
- Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
- Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
- Memory: 12868k/16384k available (2601k kernel code, 3516k reserved, 538k data, 120k init, 0k highmem)
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Time: MIPS clocksource has been installed.
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 512 (order: 0, 4096 bytes)
- TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- TCP: Hash tables configured (established 512 bind 512)
- TCP reno registered
- squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
- squashfs: LZMA suppport for slax.org by jro
- JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
- io scheduler noop registered (default)
- FLASH_API: MAN_ID=C2 DEV_ID=22CB SIZE=8MB
- Ralink gpio driver initialized
- spidrv_major = 217
- HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
- N_HDLC line discipline registered.
- Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
- serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
- loop: loaded (max 8 devices)
- rdm_major = 254
- GDMA1_MAC_ADRH -- : 0x00000000
- GDMA1_MAC_ADRL -- : 0x00000000
- Ralink APSoC Ethernet Driver Initilization. v1.60 64 rx/tx descriptors allocated, mtu = 1500!
- GDMA1_MAC_ADRH -- : 0x000080f4
- GDMA1_MAC_ADRL -- : 0xc864c7b0
- PROC INIT OK!
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- NET: Registered protocol family 24
- ralink flash device: 0x1000000 at 0xbf000000
- Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
- Amd/Fujitsu Extended Query Table at 0x0040
- number of CFI chips: 1
- cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
- Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
- 0x00000000-0x00030000 : "Bootloader"
- 0x00030000-0x00040000 : "Config"
- 0x00040000-0x00050000 : "Factory"
- 0x00050000-0x00190000 : "Kernel"
- 0x00190000-0x00750000 : "RootFS"
- 0x00750000-0x00800000 : "Jffs2"
- block2mtd: version $Revision: 1.1.1.1 $
- usbcore: registered new interface driver cdc_acm
- drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- usbcore: registered new interface driver cdc_ether
- usbcore: registered new interface driver rndis_host
- usbcore: registered new interface driver usbserial
- drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
- usbcore: registered new interface driver usbserial_generic
- drivers/usb/serial/usb-serial.c: USB Serial Driver core
- drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
- usbcore: registered new interface driver option
- drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
- usbcore: registered new interface driver usb-pcm
- drivers/usb/serial/usb-pcm.c: usb to pcm Driver: V2.4.20_uC0_1B12
- drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
- usbcore: registered new interface driver sierra
- drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.3.1b
- nf_conntrack version 0.5.0 (128 buckets, 1024 max)
- GRE over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
- TCP cubic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 10
- NET: Registered protocol family 17
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- drivers/flash/flash_ioctl.c 565
- drivers/flash/flash_ioctl.c 415
- drivers/flash/flash_ioctl.c 421
- drivers/flash/flash_ioctl.c 426
- drivers/flash/flash_ioctl.c 440
- DDNSPassword=HT_MpduDensity=5simcard_roam=roam_offPktAggregate=1unlock_at_wait=0psw_save=admin
- 44444e5350617373776f72643d0048545f4d70647544656e736974793d350073696d636172645f726f616d3d726f616d5f6f666600506b744167677265676174653d3100756e6c6f636b5f61745f776169743d30007073775f736176653d61646d696e00
- drivers/flash/flash_ioctl.c 465
- drivers/flash/flash_ioctl.c 415
- drivers/flash/flash_ioctl.c 421
- drivers/flash/flash_ioctl.c 426
- the [first:ff].[second:ff].[the last but one:ff].[last:ff], return
- drivers/flash/flash_ioctl.c 415
- drivers/flash/flash_ioctl.c 421
- drivers/flash/flash_ioctl.c 426
- the [first:ff].[second:ff].[the last but one:ff].[last:ff], return
- drivers/flash/flash_ioctl.c 567
- VFS: Mounted root (squashfs filesystem) readonly.
- Freeing unused kernel memory: 120k freed
- init started: BusyBox v1.12.1 (2011-07-11 19:10:41 CST)
- starting pid 613, tty '': '/etc_ro/rcS'
- Algorithmics/MIPS FPU Emulator v1.5
- devpts: called with bogus options
- JFFS2 notice: (619) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
- * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
- * * * * * *
- * * * * * *
- * * * * * * * * * * * *
- * * * * * * * * * * * *
- * * * * * *
- * * * * * * * * * * * * * * * * * *
- * * * * * * * * * * * * * * * * * * * * *
- * * * * * * * * * * * * *
- * * * * * * * * * * *
- * * * * * * * * * * *
- * * * * * * * * * * * * * * *
- * * * * * * * * * *
- * * * * * * * * * *
- * * * * * * * * * *
- internet.sh
- Password for 'admin' changed
- /sbin/internet.sh: line 260: wc: not found
- [: 0: unknown operand
- dwc_otg: config..done
- dwc_otg: version 2.72a 24-JUN-2008
- DWC_otg: Core Release: 2.66a
- DWC_otg: Periodic Transfer Interrupt Enhancement - disabled
- DWC_otg: Multiprocessor Interrupt Enhancement - disabled
- DWC_otg: Using DMA mode
- DWC_otg: Device using Buffer DMA mode
- dwc_otg lm0: DWC OTG Controller
- dwc_otg lm0: new USB bus registered, assigned bus number 1
- dwc_otg lm0: irq 18, io mem 0x00000000
- DWC_otg: Init: Port Power? op_state=1
- DWC_otg: Init: Power Port (0)
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- insmod: bridge.ko: module not found
- insmod: mii.ko: module not found
- insmod: raeth.ko: module not found
- phy_tx_ring = 0x00a7d000, tx_ring = 0xa0a7d000, size: 16 bytes
- phy_rx_ring = 0x00a7e000, rx_ring = 0xa0a7e000, size: 16 bytes
- GDMA1_FWD_CFG = 10000
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- ifconfig: ioctl 0x8913 failed: No such device
- rmmod: rt2860v2_ap: No such file or directory
- usb 1-1: new full speed USB device using dwc_otg and address 2
- rmmod: rt2860v2_sta: No such file or directory
- usb 1-1: configuration #1 chosen from 1 choice
- find modem i:71
- modem name: EVDO
- option 1-1:1.0: GSM modem (1-port) converter detected
- usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
- find modem i:71
- modem name: EVDO
- option 1-1:1.1: GSM modem (1-port) converter detected
- usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
- find modem i:71
- modem name: EVDO
- option 1-1:1.2: GSM modem (1-port) converter detected
- usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
- find modem i:71
- modem name: EVDO
- this is VOUSB interfacedrivers/usb/serial/usb-pcm.c :pid:152 vid:19d2
- descriptor matchesfind modem i:71
- found bulk in
- found bulk out
- ZTE port(usb-pcm) converter detected
- find modem i:71
- modem name: EVDO
- option 1-1:1.4: don't support this interface.
- drivers/usb/serial/usb-pcm.c :pid:152 vid:19d2
- descriptor matchesfind modem i:71
- this isn't VOUSB interface<4>rt2860v2_ap: module license 'unspecified' taints kernel.
- 2860 version : 2.0.0.0 (Jul 11 2011)
- === pAd = c1321000, size = 110368 ===
- rmmod: nf_nat_pptp: No such file or directory
- rmmod: nf_conntrack_pptp: No such file or directory
- rmmod: nf_nat_proto_gre: No such file or directory
- rmmod: nf_conntrack_proto_gre: No such file or directory
- RX DESC a0a94000 size = 1024
- zhaoyong MaxStaNum1=0
- 1. Phy Mode = 9
- 2. Phy Mode = 9
- 3. Phy Mode = 9
- MCS Set = ff 00 00 00 01
- The primary RSNIE: c1324cee, len = 26
- 0x0000 : 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 02
- 0x0010 : 00 50 f2 04 01 00 00 50 f2 02
- The secondary RSNIE: c1324d48, len = 24
- 0x0000 : 01 00 00 0f ac 02 02 00 00 0f ac 02 00 0f ac 04
- 0x0010 : 01 00 00 0f ac 02 00 00
- zhaoyong isRadioOff==0
- Main bssid = c8:64:c7:b0:a2:fa
- The UUID Hex string is:2880288028801880a880c864c7b0a2fa
- The UUID ASCII string is:28802880-2880-1880-a880-c864c7b0a2fa!
- 0x1300 = 00064380
- insmod: 8021q.ko: module not found
- BusyBox v1.12.1 (2011-07-11 19:10:41 CST) multi-call binary
- Usage: ifconfig [-a] interface [address]
- ifconfig: ioctl 0x8913 failed: No such device
- brctl: bridge br0: No such device or address
- iptables v1.4.0rc1: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
- Perhaps iptables or your kernel needs to be upgraded.
- device ra0 entered promiscuous mode
- ##### restore RT3052 to dump switch #####
- switch reg write offset=14, value=5555
- switch reg write offset=40, value=1001
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1001
- switch reg write offset=4c, value=1
- switch reg write offset=50, value=2001
- switch reg write offset=70, value=ffffffff
- switch reg write offset=98, value=7f7f
- switch reg write offset=e4, value=0
- device eth2 entered promiscuous mode
- br0: port 2(eth2) entering learning state
- br0: port 1(ra0) entering learning state
- route: ioctl 0x890c failed: No such process
- route: ioctl 0x890b failed: Invalid argument
- br0: port 2(eth2) entering disabled state
- br0: port 1(ra0) entering disabled state
- br0: port 2(eth2) entering learning state
- br0: port 1(ra0) entering learning state
- ifconfig: ioctl 0x8914 failed: Cannot assign requested address
- ifconfig: ioctl 0x8914 failed: Cannot assign requested address
- /sbin/lan.sh: line 65: hostname: not found
- Set: phy[0].reg[0] = 3900
- Set: phy[0].reg[0] = 3100
- Set: phy[1].reg[0] = 3900
- Set: phy[1].reg[0] = 3100
- Warning in PHY reset script
- Warning in PHY reset script
- Warning in PHY reset script
- ifconfig: ioctl 0x8913 failed: No such device
- killall rt2860apd 1>/dev/null 2>&1
- iptables -F -t filter 1>/dev/null 2>&1
- iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
- iptables -F macipport_filter 1>/dev/null 2>&1
- iptables -D FORWARD -j web_filter 1>/dev/null 2>&1
- iptables -F web_filter 1>/dev/null 2>&1
- iptables -P INPUT ACCEPT
- iptables -P OUTPUT ACCEPT
- iptables -P FORWARD ACCEPT
- iptables -t filter -N web_filter 1>/dev/null 2>&1
- iptables -t filter -N macipport_filter 1>/dev/null 2>&1
- iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
- iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
- iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
- iptables -t filter -F INPUT
- iptables -t filter -A INPUT -i ppp0 -p tcp --dport 80 -j DROP
- iptables -t filter -A INPUT -i ppp0 -p icmp -j DROP
- save index:0
- in factory model is 0
- iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
- iptables -t nat -F port_forward 1>/dev/null 2>&1; iptables -t nat -X port_forward 1>/dev/null 2>&1
- iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
- iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ 1>/dev/null 2>&1
- iptables -t nat -D PREROUTING -j addr_redirect 1>/dev/null 2>&1
- iptables -t nat -F addr_redirect 1>/dev/null 2>&1; iptables -t nat -X addr_redirect 1>/dev/null 2>&1
- iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
- iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
- iptables -t nat -N addr_redirect 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j addr_redirect 1>/dev/null 2>&1
- iptables -t nat -D POSTROUTING 1
- iptables: Index of deletion too big
- iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE
- ip_table: set wan_name=ppp0
- echo 1 > /proc/sys/net/ipv4/ip_forward
- upnp.sh
- killall: miniupnpd: no process killed
- iptables: No chain/target/match by that name
- iptables v1.4.0rc1: Couldn't find target `MINIUPNPD'
- Try `iptables -h' or 'iptables --help' for more information.
- iptables: No chain/target/match by that name
- iptables: No chain/target/match by that name
- iptables v1.4.0rc1: Couldn't find target `MINIUPNPD'
- Try `iptables -h' or 'iptables --help' for more information.
- iptables: No chain/target/match by that name
- killall: miniupnpd: no process killed
- iptables: No chain/target/match by that name
- iptables v1.4.0rc1: Couldn't find target `MINIUPNPD'
- Try `iptables -h' or 'iptables --help' for more information.
- iptables: No chain/target/match by that name
- iptables: No chain/target/match by that name
- iptables v1.4.0rc1: Couldn't find target `MINIUPNPD'
- Try `iptables -h' or 'iptables --help' for more information.
- iptables: No chain/target/match by that name
- ntp.sh
- greenap.sh init
- ddns.sh
- route delete 239.255.255.250 1>/dev/null 2>&1
- killall wscd 1>/dev/null 2>&1
- killall -9 wscd 1>/dev/null 2>&1
- iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
- iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
- killall -q klogd
- killall -q syslogd
- syslogd -C8 1>/dev/null 2>&1
- klogd 1>/dev/null 2>&1
- killall -q zebra
- killall -q ripd
- webs: Listening for HTTP requests at address 192.168.0.1
- CreateSoftTimer index 0 success:
- usTimerID = 2,
- ucFlag = 1,
- ulCurInterval = 25,
- ulNextInterval = 25,
- procCallBack = 0x00000000,
- args = 0x00000000.
- CreateSoftTimer index 1 success:
- usTimerID = 4,
- ucFlag = 1,
- ulCurInterval = 25,
- ulNextInterval = 25,
- procCallBack = 0x00000000,
- args = 0x00000000.
- CreateSoftTimer index 2 success:
- usTimerID = 7,
- ucFlag = 1,
- ulCurInterval = 25,
- ulNextInterval = 25,
- procCallBack = 0x00000000,
- args = 0x00000000.
- PCM_API: pcm_init()
- PCM_API: allocate fifo buffer
- PCM_API: allocate page buffer
- PCM_API: RALINK_SYSCTL_BASE+0x30=0x000428BC
- PCM_API: RALINK_REG_GPIOMODE=0x000003D1
- PCM_API: pcm_reg_setup
- PCM_API: pcm_reg_setup:PCM_PCMCFG=43000000
- PCM_API: PCM_GLBCFG=440000
- PCM_API: PCM_CH0_CFG=10000001
- PCM_API: PCM_CH1_CFG=40000001
- ctrl_ResetWrapper: REG_PIODATA = 0x360303
- filename:options,path:/var/ppp/options
- uaUserNameSvr:0077777115@one.co.sz,uaPassWordLoc:T3L38R
- filename:wcdma_chat,path:/var/ppp/wcdma_chat
- uaUserNameSvr:0077777115@one.co.sz,uaPassWordLoc:T3L38R
- filename:pap-secrets,path:/var/ppp/pap-secrets
- uaUserNameSvr:0077777115@one.co.sz,uaPassWordLoc:T3L38R
- filename:chap-secrets,path:/var/ppp/chap-secrets
- uaUserNameSvr:0077777115@one.co.sz,uaPassWordLoc:T3L38R
- mkdir: cannot create directory '/var/lock': File exists
- mkdir: cannot create directory '/var/log': File exists
- ctrl_ResetWrapper: REG_PIODATA = 0x360307
- si3217x : Channel 0 : Type = PROSLIC
- Si3217x : Channel 0 : VBAT Up = 59.795 v
- SLIC: ChipType = SI32171, ChipRev = B
- SLIC: slic gain ( tx = 0, rx = 6 )
- PCM_API: pcm tasklet initialization
- PCM_API: pcm volume ( tx = 1, rx = 1 )
- PCM_API: pcm_open done...
- usb2pcm_finish: c137f39c v9.36 usb2pcm_finish: b0000b00
- starting pid 1378, tty '/dev/ttyS1': '/bin/sh'
- BusyBox v1.12.1 (2011-07-11 19:10:41 CST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- ~~~~~~~~~~~~~~fsk_mode~~~~~~~~~~~~~~
- init slic api.
- -> fac Server start
- wait...
- start accept......
- Send Timer Msg Fail
- !cs_phonel initialization...cs phone begin to rcv msg from queue 98307.
- =========pRes->aucParas=^A
- ===========
- -> br0: topology change detected, propagating
- br0: port 2(eth2) entering forwarding state
- br0: topology change detected, propagating
- br0: port 1(ra0) entering forwarding state
- hrevc msg:1537 1 976894522 0
- current:1, ppp_status=ppp_idle
- elp
- ===>>>ProcAtCRSMRes<<<===
- Built-in commands:
- -------------------
- . : break cd chdir continue eval exec exit export false hash
- help local pwd read readonly return set shift source times trap
- true type ulimit umask unset wait
- -> ls -al /
- drwxr-xr-x 7 0 0 0 var
- drwxr-xr-x 5 531 502 43 usr
- drwxr-xr-x 2 0 0 0 tmp
- drwxr-xr-x 10 0 0 0 sys
- drwxr-xr-x 2 531 502 925 sbin
- dr-xr-xr-x 48 0 0 0 proc
- drwxr-xr-x 2 531 502 3 mnt
- drwxr-xr-x 2 0 0 0 media
- drwxr-xr-x 4 531 502 713 lib
- lrwxrwxrwx 1 531 502 11 init -> bin/busybox
- drwxr-xr-x 2 531 502 3 home
- drwxr-xr-x 3 0 0 0 etc_rw
- drwxr-xr-x 10 531 502 277 etc_ro
- drwxr-xr-x 3 0 0 0 etc
- drwxr-xr-x 3 531 502 672 dev
- drwxr-xr-x 2 531 502 880 bin
- drwxr-xr-x 17 531 502 170 ..
- drwxr-xr-x 17 531 502 170 .
- -> ls -al /etc ro
- drwxr-xr-x 2 531 502 60 xml
- drwxr-xr-x 2 531 502 40 wlan
- drwxr-xr-x 17 531 502 261 web
- -rw-r--r-- 1 531 502 15199 usb_modeswitch.conf
- drwxr-xr-x 2 531 502 3 usb
- lrwxrwxrwx 1 531 502 16 resolv.conf -> /var/resolv.conf
- -rwxr-xr-x 1 531 502 864 rcS
- -rw-r--r-- 1 531 502 275 radvd.conf
- drwxr-xr-x 5 531 502 145 ppp
- -rw-r--r-- 1 531 502 1094 motd
- -rw-r--r-- 1 531 502 2447 miniupnpd.conf
- br0: port 1(ra0) entering forwarding state
- hrevc msg:1537 1 976894522 0
- current:1, ppp_status=ppp_idle
- elp
- ===>>>ProcAtCRSMRes<<<===
- Built-in commands:
- -------------------
- . : break cd chdir continue eval exec exit export false hash
- help local pwd read readonly return set shift source times trap
- true type ulimit umask unset wait
- -> ls -al /
- drwxr-xr-x 7 0 0 0 var
- drwxr-xr-x 5 531 502 43 usr
- drwxr-xr-x 2 0 0 0 tmp
- drwxr-xr-x 10 0 0 0 sys
- drwxr-xr-x 2 531 502 925 sbin
- dr-xr-xr-x 48 0 0 0 proc
- drwxr-xr-x 2 531 502 3 mnt
- drwxr-xr-x 2 0 0 0 media
- drwxr-xr-x 4 531 502 713 lib
- lrwxrwxrwx 1 531 502 11 init -> bin/busybox
- drwxr-xr-x 2 531 502 3 home
- drwxr-xr-x 3 0 0 0 etc_rw
- drwxr-xr-x 10 531 502 277 etc_ro
- drwxr-xr-x 3 0 0 0 etc
- drwxr-xr-x 3 531 502 672 dev
- drwxr-xr-x 2 531 502 880 bin
- drwxr-xr-x 17 531 502 170 ..
- drwxr-xr-x 17 531 502 170 .
- -> ls -al /etc ro
- drwxr-xr-x 2 531 502 60 xml
- drwxr-xr-x 2 531 502 40 wlan
- drwxr-xr-x 17 531 502 261 web
- -rw-r--r-- 1 531 502 15199 usb_modeswitch.conf
- drwxr-xr-x 2 531 502 3 usb
- lrwxrwxrwx 1 531 502 16 resolv.conf -> /var/resolv.conf
- -rwxr-xr-x 1 531 502 864 rcS
- -rw-r--r-- 1 531 502 275 radvd.conf
- drwxr-xr-x 5 531 502 145 ppp
- -rw-r--r-- 1 531 502 1094 motd
- -rw-r--r-- 1 531 502 2447 miniupnpd.conf
- -rw-r--r-- 1 531 502 79 lld2d.conf
- drwxr-xr-x 2 531 502 3 linuxigd
- drwx------ 4 531 502 1442 l7-protocols
- -rw-r--r-- 1 531 502 45 inittab
- -rw-r--r-- 1 531 502 9662 icon.large.ico
- -rw-r--r-- 1 531 502 9662 icon.ico
- -rw-r--r-- 1 531 502 4501 default_parameter
- drwxr-xr-x 5 531 502 47 Wireless
- drwxr-xr-x 17 531 502 170 ..
- drwxr-xr-x 10 531 502 277 .
- ->
- br0: port 1(ra0) entering forwarding state
- hrevc msg:1537 1 976894522 0
- current:1, ppp_status=ppp_idle
- elp
- ===>>>ProcAtCRSMRes<<<===
- Built-in commands:
- -------------------
- . : break cd chdir continue eval exec exit export false hash
- help local pwd read readonly return set shift source times trap
- true type ulimit umask unset wait
- -> ls -al /
- drwxr-xr-x 7 0 0 0 var
- drwxr-xr-x 5 531 502 43 usr
- drwxr-xr-x 2 0 0 0 tmp
- drwxr-xr-x 10 0 0 0 sys
- drwxr-xr-x 2 531 502 925 sbin
- dr-xr-xr-x 48 0 0 0 proc
- drwxr-xr-x 2 531 502 3 mnt
- drwxr-xr-x 2 0 0 0 media
- drwxr-xr-x 4 531 502 713 lib
- lrwxrwxrwx 1 531 502 11 init -> bin/busybox
- drwxr-xr-x 2 531 502 3 home
- drwxr-xr-x 3 0 0 0 etc_rw
- drwxr-xr-x 10 531 502 277 etc_ro
- drwxr-xr-x 3 0 0 0 etc
- drwxr-xr-x 3 531 502 672 dev
- drwxr-xr-x 2 531 502 880 bin
- drwxr-xr-x 17 531 502 170 ..
- drwxr-xr-x 17 531 502 170 .
- -> ls -al /etc ro
- drwxr-xr-x 2 531 502 60 xml
- drwxr-xr-x 2 531 502 40 wlan
- drwxr-xr-x 17 531 502 261 web
- -rw-r--r-- 1 531 502 15199 usb_modeswitch.conf
- drwxr-xr-x 2 531 502 3 usb
- lrwxrwxrwx 1 531 502 16 resolv.conf -> /var/resolv.conf
- -rwxr-xr-x 1 531 502 864 rcS
- -rw-r--r-- 1 531 502 275 radvd.conf
- drwxr-xr-x 5 531 502 145 ppp
- -rw-r--r-- 1 531 502 1094 motd
- -rw-r--r-- 1 531 502 2447 miniupnpd.conf
- -rw-r--r-- 1 531 502 79 lld2d.conf
- drwxr-xr-x 2 531 502 3 linuxigd
- drwx------ 4 531 502 1442 l7-protocols
- -rw-r--r-- 1 531 502 45 inittab
- -rw-r--r-- 1 531 502 9662 icon.large.ico
- -rw-r--r-- 1 531 502 9662 icon.ico
- -rw-r--r-- 1 531 502 4501 default_parameter
- drwxr-xr-x 5 531 502 47 Wireless
- drwxr-xr-x 17 531 502 170 ..
- drwxr-xr-x 10 531 502 277 .
- ->
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement