bobstro

PrusaSlicer Filament Profiles

Jun 29th, 2019
272
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # generated by PrusaSlicer 2.2.0+ on 2020-03-23 at 15:07:09 UTC
  2.  
  3. [filament:3D PrintLife BioPETG (20181231)]
  4. bed_temperature = 70
  5. bridge_fan_speed = 50
  6. compatible_printers =
  7. compatible_printers_condition =
  8. compatible_prints =
  9. compatible_prints_condition =
  10. cooling = 1
  11. disable_fan_first_layers = 3
  12. end_filament_gcode = "; Filament-specific end gcode"
  13. extrusion_multiplier = 0.98
  14. fan_always_on = 0
  15. fan_below_layer_time = 15
  16. filament_colour = #118002
  17. filament_cooling_final_speed = 3.4
  18. filament_cooling_initial_speed = 2.2
  19. filament_cooling_moves = 4
  20. filament_cost = 53.32
  21. filament_density = 1.27
  22. filament_deretract_speed = nil
  23. filament_diameter = 1.72
  24. filament_load_time = 0
  25. filament_loading_speed = 28
  26. filament_loading_speed_start = 3
  27. filament_max_volumetric_speed = 7
  28. filament_minimal_purge_on_wipe_tower = 5
  29. filament_notes = "List of materials tested:\n\n3D PrintLife BioPETG\n\nLA, extrusion rate, temps & diameter calibrated 20190101"
  30. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  31. filament_retract_before_travel = nil
  32. filament_retract_before_wipe = nil
  33. filament_retract_layer_change = nil
  34. filament_retract_length = nil
  35. filament_retract_lift = nil
  36. filament_retract_lift_above = nil
  37. filament_retract_lift_below = nil
  38. filament_retract_restart_extra = nil
  39. filament_retract_speed = nil
  40. filament_settings_id = ""
  41. filament_soluble = 0
  42. filament_toolchange_delay = 0
  43. filament_type = PET
  44. filament_unload_time = 0
  45. filament_unloading_speed = 90
  46. filament_unloading_speed_start = 100
  47. filament_vendor = (Unknown)
  48. filament_wipe = nil
  49. first_layer_bed_temperature = 70
  50. first_layer_temperature = 235
  51. inherits =
  52. max_fan_speed = 50
  53. min_fan_speed = 30
  54. min_print_speed = 10
  55. slowdown_below_layer_time = 5
  56. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}50{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  57. temperature = 235
  58.  
  59. [filament:3D Solutech PLA (RLG 20200309)]
  60. bed_temperature = 65
  61. bridge_fan_speed = 100
  62. compatible_printers =
  63. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  64. compatible_prints =
  65. compatible_prints_condition =
  66. cooling = 1
  67. disable_fan_first_layers = 1
  68. end_filament_gcode = "; Filament-specific end gcode"
  69. extrusion_multiplier = 1
  70. fan_always_on = 1
  71. fan_below_layer_time = 100
  72. filament_colour = #FECC66
  73. filament_cooling_final_speed = 3.4
  74. filament_cooling_initial_speed = 2.2
  75. filament_cooling_moves = 4
  76. filament_cost = 16
  77. filament_density = 1.24
  78. filament_deretract_speed = nil
  79. filament_diameter = 1.74
  80. filament_load_time = 0
  81. filament_loading_speed = 28
  82. filament_loading_speed_start = 3
  83. filament_max_volumetric_speed = 15
  84. filament_minimal_purge_on_wipe_tower = 15
  85. filament_notes = "List of materials tested:\n\n3D Solutech PLA\n\nLA, extrusion multiplier and diameter calibrated 20200308"
  86. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  87. filament_retract_before_travel = nil
  88. filament_retract_before_wipe = nil
  89. filament_retract_layer_change = nil
  90. filament_retract_length = nil
  91. filament_retract_lift = nil
  92. filament_retract_lift_above = nil
  93. filament_retract_lift_below = nil
  94. filament_retract_restart_extra = nil
  95. filament_retract_speed = nil
  96. filament_settings_id = ""
  97. filament_soluble = 0
  98. filament_toolchange_delay = 0
  99. filament_type = PLA
  100. filament_unload_time = 0
  101. filament_unloading_speed = 90
  102. filament_unloading_speed_start = 100
  103. filament_vendor = Generic
  104. filament_wipe = nil
  105. first_layer_bed_temperature = 65
  106. first_layer_temperature = 210
  107. inherits =
  108. max_fan_speed = 100
  109. min_fan_speed = 100
  110. min_print_speed = 15
  111. slowdown_below_layer_time = 20
  112. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}18{else}35{endif} ; Filament gcode linear advance\nM900 W0 H0 D0"
  113. temperature = 210
  114.  
  115. [filament:3D-Fuel Wound Up (RLG 20180624)]
  116. bed_temperature = 60
  117. bridge_fan_speed = 100
  118. compatible_printers =
  119. compatible_printers_condition = nozzle_diameter[0]>0.35
  120. compatible_prints =
  121. compatible_prints_condition =
  122. cooling = 1
  123. disable_fan_first_layers = 1
  124. end_filament_gcode = "; Filament-specific end gcode"
  125. extrusion_multiplier = 1.2
  126. fan_always_on = 1
  127. fan_below_layer_time = 100
  128. filament_colour = #804040
  129. filament_cooling_final_speed = 3.4
  130. filament_cooling_initial_speed = 2.2
  131. filament_cooling_moves = 4
  132. filament_cost = 0
  133. filament_density = 0
  134. filament_deretract_speed = nil
  135. filament_diameter = 1.75
  136. filament_load_time = 0
  137. filament_loading_speed = 28
  138. filament_loading_speed_start = 3
  139. filament_max_volumetric_speed = 10
  140. filament_minimal_purge_on_wipe_tower = 5
  141. filament_notes = "3Dom 3D-Fuel Wound-Up"
  142. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  143. filament_retract_before_travel = nil
  144. filament_retract_before_wipe = nil
  145. filament_retract_layer_change = nil
  146. filament_retract_length = nil
  147. filament_retract_lift = nil
  148. filament_retract_lift_above = nil
  149. filament_retract_lift_below = nil
  150. filament_retract_restart_extra = nil
  151. filament_retract_speed = nil
  152. filament_settings_id = ""
  153. filament_soluble = 0
  154. filament_toolchange_delay = 0
  155. filament_type = PLA
  156. filament_unload_time = 0
  157. filament_unloading_speed = 90
  158. filament_unloading_speed_start = 100
  159. filament_vendor = (Unknown)
  160. filament_wipe = nil
  161. first_layer_bed_temperature = 60
  162. first_layer_temperature = 210
  163. inherits =
  164. max_fan_speed = 100
  165. min_fan_speed = 100
  166. min_print_speed = 10
  167. slowdown_below_layer_time = 5
  168. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  169. temperature = 210
  170.  
  171. [filament:3DXtech PETG (RLG 20190226)]
  172. bed_temperature = 75
  173. bridge_fan_speed = 50
  174. compatible_printers =
  175. compatible_printers_condition =
  176. compatible_prints =
  177. compatible_prints_condition =
  178. cooling = 1
  179. disable_fan_first_layers = 3
  180. end_filament_gcode = "; Filament-specific end gcode"
  181. extrusion_multiplier = 0.97
  182. fan_always_on = 0
  183. fan_below_layer_time = 20
  184. filament_colour = #FF8000
  185. filament_cooling_final_speed = 3.4
  186. filament_cooling_initial_speed = 2.2
  187. filament_cooling_moves = 4
  188. filament_cost = 38
  189. filament_density = 1.27
  190. filament_deretract_speed = nil
  191. filament_diameter = 1.73
  192. filament_load_time = 0
  193. filament_loading_speed = 28
  194. filament_loading_speed_start = 3
  195. filament_max_volumetric_speed = 7
  196. filament_minimal_purge_on_wipe_tower = 5
  197. filament_notes = "List of manufacturers tested:\n\n3DXTech Matte PETG\n\nLA, extrusion rate, temps & diameter calibrated 20190226\n\nNozzle temperature: 260-280C Bed temperature: 60-80C"
  198. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  199. filament_retract_before_travel = nil
  200. filament_retract_before_wipe = nil
  201. filament_retract_layer_change = nil
  202. filament_retract_length = nil
  203. filament_retract_lift = nil
  204. filament_retract_lift_above = nil
  205. filament_retract_lift_below = nil
  206. filament_retract_restart_extra = nil
  207. filament_retract_speed = nil
  208. filament_settings_id = ""
  209. filament_soluble = 0
  210. filament_toolchange_delay = 0
  211. filament_type = PET
  212. filament_unload_time = 0
  213. filament_unloading_speed = 90
  214. filament_unloading_speed_start = 100
  215. filament_vendor = (Unknown)
  216. filament_wipe = nil
  217. first_layer_bed_temperature = 80
  218. first_layer_temperature = 270
  219. inherits =
  220. max_fan_speed = 30
  221. min_fan_speed = 0
  222. min_print_speed = 10
  223. slowdown_below_layer_time = 5
  224. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  225. temperature = 270
  226.  
  227. [filament:AIO Robotics PLA (RLG 201901625)]
  228. bed_temperature = 65
  229. bridge_fan_speed = 100
  230. compatible_printers =
  231. compatible_printers_condition =
  232. compatible_prints =
  233. compatible_prints_condition =
  234. cooling = 1
  235. disable_fan_first_layers = 1
  236. end_filament_gcode = "; Filament-specific end gcode"
  237. extrusion_multiplier = 0.84
  238. fan_always_on = 1
  239. fan_below_layer_time = 100
  240. filament_colour = #E75C00
  241. filament_cooling_final_speed = 3.4
  242. filament_cooling_initial_speed = 2.2
  243. filament_cooling_moves = 4
  244. filament_cost = 24.9
  245. filament_density = 1.25
  246. filament_deretract_speed = nil
  247. filament_diameter = 1.72
  248. filament_load_time = 0
  249. filament_loading_speed = 28
  250. filament_loading_speed_start = 3
  251. filament_max_volumetric_speed = 15
  252. filament_minimal_purge_on_wipe_tower = 5
  253. filament_notes = "List of materials tested:\n\nAIO Robotics PLA\n\nLA, extrusion & diameter calibrated 20181005"
  254. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  255. filament_retract_before_travel = nil
  256. filament_retract_before_wipe = nil
  257. filament_retract_layer_change = nil
  258. filament_retract_length = nil
  259. filament_retract_lift = nil
  260. filament_retract_lift_above = nil
  261. filament_retract_lift_below = nil
  262. filament_retract_restart_extra = nil
  263. filament_retract_speed = nil
  264. filament_settings_id = ""
  265. filament_soluble = 0
  266. filament_toolchange_delay = 0
  267. filament_type = PLA
  268. filament_unload_time = 0
  269. filament_unloading_speed = 90
  270. filament_unloading_speed_start = 100
  271. filament_vendor = (Unknown)
  272. filament_wipe = nil
  273. first_layer_bed_temperature = 65
  274. first_layer_temperature = 215
  275. inherits =
  276. max_fan_speed = 100
  277. min_fan_speed = 75
  278. min_print_speed = 10
  279. slowdown_below_layer_time = 5
  280. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode"
  281. temperature = 210
  282.  
  283. [filament:AmazonBasics PETG (RLG 20200226)]
  284. bed_temperature = 80
  285. bridge_fan_speed = 50
  286. compatible_printers =
  287. compatible_printers_condition =
  288. compatible_prints =
  289. compatible_prints_condition =
  290. cooling = 1
  291. disable_fan_first_layers = 3
  292. end_filament_gcode = "; Filament-specific end gcode"
  293. extrusion_multiplier = 0.98
  294. fan_always_on = 0
  295. fan_below_layer_time = 15
  296. filament_colour = #074080
  297. filament_cooling_final_speed = 3.4
  298. filament_cooling_initial_speed = 2.2
  299. filament_cooling_moves = 4
  300. filament_cost = 18.99
  301. filament_density = 1.23
  302. filament_deretract_speed = nil
  303. filament_diameter = 1.72
  304. filament_load_time = 0
  305. filament_loading_speed = 28
  306. filament_loading_speed_start = 3
  307. filament_max_volumetric_speed = 7
  308. filament_minimal_purge_on_wipe_tower = 5
  309. filament_notes = "List of materials tested:\n\nAmazonBasics PETG\n\nLA, extrusion rate, temp & diameter calibrated 20200226\n"
  310. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  311. filament_retract_before_travel = nil
  312. filament_retract_before_wipe = nil
  313. filament_retract_layer_change = nil
  314. filament_retract_length = 0.6
  315. filament_retract_lift = 0.6
  316. filament_retract_lift_above = nil
  317. filament_retract_lift_below = nil
  318. filament_retract_restart_extra = nil
  319. filament_retract_speed = nil
  320. filament_settings_id = ""
  321. filament_soluble = 0
  322. filament_toolchange_delay = 0
  323. filament_type = PET
  324. filament_unload_time = 0
  325. filament_unloading_speed = 90
  326. filament_unloading_speed_start = 100
  327. filament_vendor = (Unknown)
  328. filament_wipe = nil
  329. first_layer_bed_temperature = 80
  330. first_layer_temperature = 230
  331. inherits =
  332. max_fan_speed = 50
  333. min_fan_speed = 30
  334. min_print_speed = 10
  335. slowdown_below_layer_time = 5
  336. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}50{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  337. temperature = 235
  338.  
  339. [filament:Atomic Filament Carbon Fiber PETG (RLG 20180718)]
  340. bed_temperature = 65
  341. bridge_fan_speed = 50
  342. compatible_printers =
  343. compatible_printers_condition =
  344. compatible_prints =
  345. compatible_prints_condition =
  346. cooling = 1
  347. disable_fan_first_layers = 3
  348. end_filament_gcode = "; Filament-specific end gcode"
  349. extrusion_multiplier = 0.94
  350. fan_always_on = 0
  351. fan_below_layer_time = 15
  352. filament_colour = #43485B
  353. filament_cooling_final_speed = 3.4
  354. filament_cooling_initial_speed = 2.2
  355. filament_cooling_moves = 4
  356. filament_cost = 49.99
  357. filament_density = 0
  358. filament_deretract_speed = nil
  359. filament_diameter = 1.73
  360. filament_load_time = 0
  361. filament_loading_speed = 28
  362. filament_loading_speed_start = 3
  363. filament_max_volumetric_speed = 5
  364. filament_minimal_purge_on_wipe_tower = 5
  365. filament_notes = "List of manufacturers tested with standard PET print settings for MK2:\n\nAtomic Filament Carbon Fiber Extreme PETG\nNozzle temperature 245-265C\nHeated bed temperature 60-70C\n"
  366. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  367. filament_retract_before_travel = nil
  368. filament_retract_before_wipe = nil
  369. filament_retract_layer_change = nil
  370. filament_retract_length = nil
  371. filament_retract_lift = nil
  372. filament_retract_lift_above = nil
  373. filament_retract_lift_below = nil
  374. filament_retract_restart_extra = nil
  375. filament_retract_speed = nil
  376. filament_settings_id = ""
  377. filament_soluble = 0
  378. filament_toolchange_delay = 0
  379. filament_type = PET
  380. filament_unload_time = 0
  381. filament_unloading_speed = 90
  382. filament_unloading_speed_start = 100
  383. filament_vendor = (Unknown)
  384. filament_wipe = nil
  385. first_layer_bed_temperature = 60
  386. first_layer_temperature = 255
  387. inherits =
  388. max_fan_speed = 50
  389. min_fan_speed = 30
  390. min_print_speed = 10
  391. slowdown_below_layer_time = 5
  392. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  393. temperature = 250
  394.  
  395. [filament:ColorFabb HT (RLG 20190526)]
  396. bed_temperature = 100
  397. bridge_fan_speed = 80
  398. compatible_printers =
  399. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
  400. compatible_prints =
  401. compatible_prints_condition =
  402. cooling = 1
  403. disable_fan_first_layers = 20
  404. end_filament_gcode = "; Filament-specific end gcode"
  405. extrusion_multiplier = 1
  406. fan_always_on = 0
  407. fan_below_layer_time = 10
  408. filament_colour = #FF8000
  409. filament_cooling_final_speed = 3.4
  410. filament_cooling_initial_speed = 2.2
  411. filament_cooling_moves = 4
  412. filament_cost = 58.66
  413. filament_density = 1.18
  414. filament_deretract_speed = nil
  415. filament_diameter = 1.75
  416. filament_load_time = 0
  417. filament_loading_speed = 28
  418. filament_loading_speed_start = 3
  419. filament_max_volumetric_speed = 7.5
  420. filament_minimal_purge_on_wipe_tower = 15
  421. filament_notes = "List of materials tested:\n\nColorFabb HT\n\nLA, extrusion multiplier and diameter calibrated"
  422. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  423. filament_retract_before_travel = nil
  424. filament_retract_before_wipe = nil
  425. filament_retract_layer_change = nil
  426. filament_retract_length = nil
  427. filament_retract_lift = nil
  428. filament_retract_lift_above = nil
  429. filament_retract_lift_below = nil
  430. filament_retract_restart_extra = nil
  431. filament_retract_speed = nil
  432. filament_settings_id = ""
  433. filament_soluble = 0
  434. filament_toolchange_delay = 0
  435. filament_type = HT
  436. filament_unload_time = 0
  437. filament_unloading_speed = 90
  438. filament_unloading_speed_start = 100
  439. filament_vendor = (Unknown)
  440. filament_wipe = nil
  441. first_layer_bed_temperature = 100
  442. first_layer_temperature = 260
  443. inherits =
  444. max_fan_speed = 50
  445. min_fan_speed = 10
  446. min_print_speed = 10
  447. slowdown_below_layer_time = 15
  448. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  449. temperature = 265
  450.  
  451. [filament:ColorFabb XT (RLG 20181025)]
  452. bed_temperature = 65
  453. bridge_fan_speed = 50
  454. compatible_printers =
  455. compatible_printers_condition =
  456. compatible_prints =
  457. compatible_prints_condition =
  458. cooling = 1
  459. disable_fan_first_layers = 1
  460. end_filament_gcode = "; Filament-specific end gcode"
  461. extrusion_multiplier = 0.92
  462. fan_always_on = 0
  463. fan_below_layer_time = 20
  464. filament_colour = #51B6F4
  465. filament_cooling_final_speed = 3.4
  466. filament_cooling_initial_speed = 2.2
  467. filament_cooling_moves = 4
  468. filament_cost = 61.27
  469. filament_density = 1.27
  470. filament_deretract_speed = nil
  471. filament_diameter = 1.74
  472. filament_load_time = 0
  473. filament_loading_speed = 28
  474. filament_loading_speed_start = 3
  475. filament_max_volumetric_speed = 7
  476. filament_minimal_purge_on_wipe_tower = 5
  477. filament_notes = "Temperature: 240-245\nBuild plate temperature: 70\nCooling: Off 1 cm"
  478. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  479. filament_retract_before_travel = nil
  480. filament_retract_before_wipe = nil
  481. filament_retract_layer_change = nil
  482. filament_retract_length = nil
  483. filament_retract_lift = nil
  484. filament_retract_lift_above = nil
  485. filament_retract_lift_below = nil
  486. filament_retract_restart_extra = nil
  487. filament_retract_speed = nil
  488. filament_settings_id = ""
  489. filament_soluble = 0
  490. filament_toolchange_delay = 0
  491. filament_type = XT
  492. filament_unload_time = 0
  493. filament_unloading_speed = 90
  494. filament_unloading_speed_start = 100
  495. filament_vendor = (Unknown)
  496. filament_wipe = nil
  497. first_layer_bed_temperature = 80
  498. first_layer_temperature = 250
  499. inherits =
  500. max_fan_speed = 40
  501. min_fan_speed = 25
  502. min_print_speed = 10
  503. slowdown_below_layer_time = 5
  504. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  505. temperature = 247
  506.  
  507. [filament:ColorFabb nGen (RLG 20181018)]
  508. bed_temperature = 75
  509. bridge_fan_speed = 15
  510. compatible_printers =
  511. compatible_printers_condition =
  512. compatible_prints =
  513. compatible_prints_condition =
  514. cooling = 1
  515. disable_fan_first_layers = 3
  516. end_filament_gcode = "; Filament-specific end gcode"
  517. extrusion_multiplier = 0.87
  518. fan_always_on = 0
  519. fan_below_layer_time = 10
  520. filament_colour = #14FA00
  521. filament_cooling_final_speed = 3.4
  522. filament_cooling_initial_speed = 2.2
  523. filament_cooling_moves = 4
  524. filament_cost = 51.98
  525. filament_density = 0
  526. filament_deretract_speed = nil
  527. filament_diameter = 1.748
  528. filament_load_time = 0
  529. filament_loading_speed = 28
  530. filament_loading_speed_start = 3
  531. filament_max_volumetric_speed = 8
  532. filament_minimal_purge_on_wipe_tower = 5
  533. filament_notes = "List of materials tested:\n\nColorFabb nGen\n\nLA, extrusion multiplier and diameter calibrated 20181006\n"
  534. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  535. filament_retract_before_travel = nil
  536. filament_retract_before_wipe = nil
  537. filament_retract_layer_change = nil
  538. filament_retract_length = nil
  539. filament_retract_lift = nil
  540. filament_retract_lift_above = nil
  541. filament_retract_lift_below = nil
  542. filament_retract_restart_extra = nil
  543. filament_retract_speed = nil
  544. filament_settings_id = ""
  545. filament_soluble = 0
  546. filament_toolchange_delay = 0
  547. filament_type = NGEN
  548. filament_unload_time = 0
  549. filament_unloading_speed = 90
  550. filament_unloading_speed_start = 100
  551. filament_vendor = (Unknown)
  552. filament_wipe = nil
  553. first_layer_bed_temperature = 75
  554. first_layer_temperature = 220
  555. inherits =
  556. max_fan_speed = 80
  557. min_fan_speed = 30
  558. min_print_speed = 10
  559. slowdown_below_layer_time = 5
  560. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  561. temperature = 220
  562.  
  563. [filament:ColorFabb nGen Flex (RLG 20180718)]
  564. bed_temperature = 65
  565. bridge_fan_speed = 40
  566. compatible_printers =
  567. compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1
  568. compatible_prints =
  569. compatible_prints_condition =
  570. cooling = 1
  571. disable_fan_first_layers = 3
  572. end_filament_gcode = "; Filament-specific end gcode"
  573. extrusion_multiplier = 1
  574. fan_always_on = 0
  575. fan_below_layer_time = 10
  576. filament_colour = #D3005E
  577. filament_cooling_final_speed = 3.4
  578. filament_cooling_initial_speed = 2.2
  579. filament_cooling_moves = 4
  580. filament_cost = 70.69
  581. filament_density = 1.13
  582. filament_deretract_speed = nil
  583. filament_diameter = 1.75
  584. filament_load_time = 0
  585. filament_loading_speed = 28
  586. filament_loading_speed_start = 3
  587. filament_max_volumetric_speed = 5
  588. filament_minimal_purge_on_wipe_tower = 5
  589. filament_notes = ""
  590. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  591. filament_retract_before_travel = nil
  592. filament_retract_before_wipe = nil
  593. filament_retract_layer_change = nil
  594. filament_retract_length = nil
  595. filament_retract_lift = nil
  596. filament_retract_lift_above = nil
  597. filament_retract_lift_below = nil
  598. filament_retract_restart_extra = nil
  599. filament_retract_speed = nil
  600. filament_settings_id = ""
  601. filament_soluble = 0
  602. filament_toolchange_delay = 0
  603. filament_type = FLEX
  604. filament_unload_time = 0
  605. filament_unloading_speed = 90
  606. filament_unloading_speed_start = 100
  607. filament_vendor = (Unknown)
  608. filament_wipe = nil
  609. first_layer_bed_temperature = 65
  610. first_layer_temperature = 250
  611. inherits =
  612. max_fan_speed = 35
  613. min_fan_speed = 20
  614. min_print_speed = 10
  615. slowdown_below_layer_time = 5
  616. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  617. temperature = 250
  618.  
  619. [filament:FilaCube PLA (RLG 20190312)]
  620. bed_temperature = 60
  621. bridge_fan_speed = 100
  622. compatible_printers =
  623. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  624. compatible_prints =
  625. compatible_prints_condition =
  626. cooling = 1
  627. disable_fan_first_layers = 1
  628. end_filament_gcode = "; Filament-specific end gcode"
  629. extrusion_multiplier = 0.95
  630. fan_always_on = 1
  631. fan_below_layer_time = 100
  632. filament_colour = #FF3232
  633. filament_cooling_final_speed = 3.4
  634. filament_cooling_initial_speed = 2.2
  635. filament_cooling_moves = 4
  636. filament_cost = 21.97
  637. filament_density = 1.24
  638. filament_deretract_speed = nil
  639. filament_diameter = 1.746
  640. filament_load_time = 0
  641. filament_loading_speed = 28
  642. filament_loading_speed_start = 3
  643. filament_max_volumetric_speed = 15
  644. filament_minimal_purge_on_wipe_tower = 15
  645. filament_notes = "List of materials tested:\n\nFilaCube PLA \n\nLA, extrusion rate, temp & diameter calibrated 20190310\n"
  646. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  647. filament_retract_before_travel = nil
  648. filament_retract_before_wipe = nil
  649. filament_retract_layer_change = nil
  650. filament_retract_length = nil
  651. filament_retract_lift = nil
  652. filament_retract_lift_above = nil
  653. filament_retract_lift_below = nil
  654. filament_retract_restart_extra = nil
  655. filament_retract_speed = nil
  656. filament_settings_id = "FilaCube PLA (RLG 20190312)"
  657. filament_soluble = 0
  658. filament_toolchange_delay = 0
  659. filament_type = PLA
  660. filament_unload_time = 0
  661. filament_unloading_speed = 90
  662. filament_unloading_speed_start = 100
  663. filament_vendor = (Unknown)
  664. filament_wipe = nil
  665. first_layer_bed_temperature = 60
  666. first_layer_temperature = 205
  667. inherits = Generic PLA
  668. max_fan_speed = 100
  669. min_fan_speed = 100
  670. min_print_speed = 10
  671. slowdown_below_layer_time = 5
  672. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}33{endif}; Filament gcode"
  673. temperature = 200
  674.  
  675. [filament:Filastruder Veracity PETG (RLG 20181227)]
  676. bed_temperature = 80
  677. bridge_fan_speed = 50
  678. compatible_printers =
  679. compatible_printers_condition =
  680. compatible_prints =
  681. compatible_prints_condition =
  682. cooling = 1
  683. disable_fan_first_layers = 3
  684. end_filament_gcode = "; Filament-specific end gcode"
  685. extrusion_multiplier = 0.99
  686. fan_always_on = 0
  687. fan_below_layer_time = 20
  688. filament_colour = #FB0106
  689. filament_cooling_final_speed = 3.4
  690. filament_cooling_initial_speed = 2.2
  691. filament_cooling_moves = 4
  692. filament_cost = 24.99
  693. filament_density = 1.27
  694. filament_deretract_speed = nil
  695. filament_diameter = 1.75
  696. filament_load_time = 0
  697. filament_loading_speed = 28
  698. filament_loading_speed_start = 3
  699. filament_max_volumetric_speed = 8
  700. filament_minimal_purge_on_wipe_tower = 5
  701. filament_notes = "List of materials tested:\n\nFilastruder Veracity PETG\n\nLA, extrusion rate & diameter calibrated 20181227"
  702. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  703. filament_retract_before_travel = nil
  704. filament_retract_before_wipe = nil
  705. filament_retract_layer_change = nil
  706. filament_retract_length = nil
  707. filament_retract_lift = nil
  708. filament_retract_lift_above = nil
  709. filament_retract_lift_below = nil
  710. filament_retract_restart_extra = nil
  711. filament_retract_speed = nil
  712. filament_settings_id = ""
  713. filament_soluble = 0
  714. filament_toolchange_delay = 0
  715. filament_type = PET
  716. filament_unload_time = 0
  717. filament_unloading_speed = 90
  718. filament_unloading_speed_start = 100
  719. filament_vendor = (Unknown)
  720. filament_wipe = nil
  721. first_layer_bed_temperature = 80
  722. first_layer_temperature = 240
  723. inherits =
  724. max_fan_speed = 50
  725. min_fan_speed = 30
  726. min_print_speed = 10
  727. slowdown_below_layer_time = 5
  728. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}70{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  729. temperature = 240
  730.  
  731. [filament:Fillamentum Extrafill (RLG 20181005)]
  732. bed_temperature = 65
  733. bridge_fan_speed = 100
  734. compatible_printers =
  735. compatible_printers_condition = nozzle_diameter[0]>0.35
  736. compatible_prints =
  737. compatible_prints_condition =
  738. cooling = 1
  739. disable_fan_first_layers = 1
  740. end_filament_gcode = "; Filament-specific end gcode"
  741. extrusion_multiplier = 0.915
  742. fan_always_on = 0
  743. fan_below_layer_time = 100
  744. filament_colour = #54EDDC
  745. filament_cooling_final_speed = 3.4
  746. filament_cooling_initial_speed = 2.2
  747. filament_cooling_moves = 4
  748. filament_cost = 54.66
  749. filament_density = 1.24
  750. filament_deretract_speed = nil
  751. filament_diameter = 1.7
  752. filament_load_time = 0
  753. filament_loading_speed = 28
  754. filament_loading_speed_start = 3
  755. filament_max_volumetric_speed = 6
  756. filament_minimal_purge_on_wipe_tower = 5
  757. filament_notes = "Fillamentum Vertigo Gray\nNozzle temperature: 190-210C\nBed: \n"
  758. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  759. filament_retract_before_travel = nil
  760. filament_retract_before_wipe = nil
  761. filament_retract_layer_change = nil
  762. filament_retract_length = nil
  763. filament_retract_lift = nil
  764. filament_retract_lift_above = nil
  765. filament_retract_lift_below = nil
  766. filament_retract_restart_extra = nil
  767. filament_retract_speed = nil
  768. filament_settings_id = ""
  769. filament_soluble = 0
  770. filament_toolchange_delay = 0
  771. filament_type = PLA
  772. filament_unload_time = 0
  773. filament_unloading_speed = 90
  774. filament_unloading_speed_start = 100
  775. filament_vendor = (Unknown)
  776. filament_wipe = nil
  777. first_layer_bed_temperature = 65
  778. first_layer_temperature = 205
  779. inherits =
  780. max_fan_speed = 50
  781. min_fan_speed = 25
  782. min_print_speed = 10
  783. slowdown_below_layer_time = 5
  784. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  785. temperature = 200
  786.  
  787. [filament:FormFutura ReForm rPET (RLG 20190124)]
  788. bed_temperature = 80
  789. bridge_fan_speed = 50
  790. compatible_printers =
  791. compatible_printers_condition =
  792. compatible_prints =
  793. compatible_prints_condition =
  794. cooling = 1
  795. disable_fan_first_layers = 3
  796. end_filament_gcode = "; Filament-specific end gcode"
  797. extrusion_multiplier = 0.91
  798. fan_always_on = 0
  799. fan_below_layer_time = 30
  800. filament_colour = #118002
  801. filament_cooling_final_speed = 3.4
  802. filament_cooling_initial_speed = 2.2
  803. filament_cooling_moves = 4
  804. filament_cost = 39.99
  805. filament_density = 1.27
  806. filament_deretract_speed = nil
  807. filament_diameter = 1.75
  808. filament_load_time = 0
  809. filament_loading_speed = 28
  810. filament_loading_speed_start = 3
  811. filament_max_volumetric_speed = 8
  812. filament_minimal_purge_on_wipe_tower = 5
  813. filament_notes = "List of materials tested:\n\nFormFutura rPET\n\nLA, extrusion rate, temp & diameter calibrated 20181231"
  814. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  815. filament_retract_before_travel = nil
  816. filament_retract_before_wipe = nil
  817. filament_retract_layer_change = nil
  818. filament_retract_length = nil
  819. filament_retract_lift = nil
  820. filament_retract_lift_above = nil
  821. filament_retract_lift_below = nil
  822. filament_retract_restart_extra = nil
  823. filament_retract_speed = nil
  824. filament_settings_id = ""
  825. filament_soluble = 0
  826. filament_toolchange_delay = 0
  827. filament_type = PET
  828. filament_unload_time = 0
  829. filament_unloading_speed = 90
  830. filament_unloading_speed_start = 100
  831. filament_vendor = (Unknown)
  832. filament_wipe = nil
  833. first_layer_bed_temperature = 80
  834. first_layer_temperature = 215
  835. inherits =
  836. max_fan_speed = 100
  837. min_fan_speed = 50
  838. min_print_speed = 10
  839. slowdown_below_layer_time = 5
  840. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  841. temperature = 215
  842.  
  843. [filament:Formfutura StoneFil (RLG 20180904)]
  844. bed_temperature = 60
  845. bridge_fan_speed = 100
  846. compatible_printers =
  847. compatible_printers_condition = nozzle_diameter[0]>0.35
  848. compatible_prints =
  849. compatible_prints_condition =
  850. cooling = 1
  851. disable_fan_first_layers = 1
  852. end_filament_gcode = "; Filament-specific end gcode"
  853. extrusion_multiplier = 1
  854. fan_always_on = 1
  855. fan_below_layer_time = 100
  856. filament_colour = #2D9388
  857. filament_cooling_final_speed = 3.4
  858. filament_cooling_initial_speed = 2.2
  859. filament_cooling_moves = 4
  860. filament_cost = 79.9
  861. filament_density = 0
  862. filament_deretract_speed = nil
  863. filament_diameter = 1.72
  864. filament_load_time = 0
  865. filament_loading_speed = 28
  866. filament_loading_speed_start = 3
  867. filament_max_volumetric_speed = 10
  868. filament_minimal_purge_on_wipe_tower = 5
  869. filament_notes = "Print temperature: 200-240C\n"
  870. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  871. filament_retract_before_travel = nil
  872. filament_retract_before_wipe = nil
  873. filament_retract_layer_change = nil
  874. filament_retract_length = nil
  875. filament_retract_lift = nil
  876. filament_retract_lift_above = nil
  877. filament_retract_lift_below = nil
  878. filament_retract_restart_extra = nil
  879. filament_retract_speed = nil
  880. filament_settings_id = ""
  881. filament_soluble = 0
  882. filament_toolchange_delay = 0
  883. filament_type = PLA
  884. filament_unload_time = 0
  885. filament_unloading_speed = 90
  886. filament_unloading_speed_start = 100
  887. filament_vendor = (Unknown)
  888. filament_wipe = nil
  889. first_layer_bed_temperature = 60
  890. first_layer_temperature = 220
  891. inherits =
  892. max_fan_speed = 50
  893. min_fan_speed = 50
  894. min_print_speed = 10
  895. slowdown_below_layer_time = 5
  896. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  897. temperature = 220
  898.  
  899. [filament:GizmoDorks PETG (RLG 20190102)]
  900. bed_temperature = 80
  901. bridge_fan_speed = 50
  902. compatible_printers =
  903. compatible_printers_condition =
  904. compatible_prints =
  905. compatible_prints_condition =
  906. cooling = 1
  907. disable_fan_first_layers = 3
  908. end_filament_gcode = "; Filament-specific end gcode"
  909. extrusion_multiplier = 1
  910. fan_always_on = 0
  911. fan_below_layer_time = 15
  912. filament_colour = #800080
  913. filament_cooling_final_speed = 3.4
  914. filament_cooling_initial_speed = 2.2
  915. filament_cooling_moves = 4
  916. filament_cost = 26.95
  917. filament_density = 1.27
  918. filament_deretract_speed = nil
  919. filament_diameter = 1.71
  920. filament_load_time = 0
  921. filament_loading_speed = 28
  922. filament_loading_speed_start = 3
  923. filament_max_volumetric_speed = 8
  924. filament_minimal_purge_on_wipe_tower = 5
  925. filament_notes = "List of materials tested:\n\nGizmoDorks PETG\n\nLA, extrusion rate, temp & diameter calibrated 20190103"
  926. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  927. filament_retract_before_travel = nil
  928. filament_retract_before_wipe = nil
  929. filament_retract_layer_change = nil
  930. filament_retract_length = nil
  931. filament_retract_lift = nil
  932. filament_retract_lift_above = nil
  933. filament_retract_lift_below = nil
  934. filament_retract_restart_extra = nil
  935. filament_retract_speed = nil
  936. filament_settings_id = ""
  937. filament_soluble = 0
  938. filament_toolchange_delay = 0
  939. filament_type = PET
  940. filament_unload_time = 0
  941. filament_unloading_speed = 90
  942. filament_unloading_speed_start = 100
  943. filament_vendor = (Unknown)
  944. filament_wipe = nil
  945. first_layer_bed_temperature = 80
  946. first_layer_temperature = 245
  947. inherits =
  948. max_fan_speed = 50
  949. min_fan_speed = 30
  950. min_print_speed = 10
  951. slowdown_below_layer_time = 5
  952. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  953. temperature = 230
  954.  
  955. [filament:GizmoDorks PLA (RLG 20181018)]
  956. bed_temperature = 60
  957. bridge_fan_speed = 100
  958. compatible_printers =
  959. compatible_printers_condition =
  960. compatible_prints =
  961. compatible_prints_condition =
  962. cooling = 1
  963. disable_fan_first_layers = 1
  964. end_filament_gcode = "; Filament-specific end gcode"
  965. extrusion_multiplier = 0.9
  966. fan_always_on = 1
  967. fan_below_layer_time = 100
  968. filament_colour = #EAEA2F
  969. filament_cooling_final_speed = 3.4
  970. filament_cooling_initial_speed = 2.2
  971. filament_cooling_moves = 4
  972. filament_cost = 44.75
  973. filament_density = 6.95159e-310
  974. filament_deretract_speed = nil
  975. filament_diameter = 1.726
  976. filament_load_time = 0
  977. filament_loading_speed = 28
  978. filament_loading_speed_start = 3
  979. filament_max_volumetric_speed = 15
  980. filament_minimal_purge_on_wipe_tower = 5
  981. filament_notes = "List of materials tested:\n\nGizmoDorks PLA\n\nLA, extrusion rate & diameter calibrated 20181018"
  982. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  983. filament_retract_before_travel = nil
  984. filament_retract_before_wipe = nil
  985. filament_retract_layer_change = nil
  986. filament_retract_length = nil
  987. filament_retract_lift = nil
  988. filament_retract_lift_above = nil
  989. filament_retract_lift_below = nil
  990. filament_retract_restart_extra = nil
  991. filament_retract_speed = nil
  992. filament_settings_id = ""
  993. filament_soluble = 0
  994. filament_toolchange_delay = 0
  995. filament_type = PLA
  996. filament_unload_time = 0
  997. filament_unloading_speed = 90
  998. filament_unloading_speed_start = 100
  999. filament_vendor = (Unknown)
  1000. filament_wipe = nil
  1001. first_layer_bed_temperature = 60
  1002. first_layer_temperature = 205
  1003. inherits =
  1004. max_fan_speed = 70
  1005. min_fan_speed = 50
  1006. min_print_speed = 10
  1007. slowdown_below_layer_time = 5
  1008. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1009. temperature = 200
  1010.  
  1011. [filament:Inland PETG (RLG 20181126)]
  1012. bed_temperature = 90
  1013. bridge_fan_speed = 50
  1014. compatible_printers =
  1015. compatible_printers_condition =
  1016. compatible_prints =
  1017. compatible_prints_condition =
  1018. cooling = 1
  1019. disable_fan_first_layers = 3
  1020. end_filament_gcode = "; Filament-specific end gcode"
  1021. extrusion_multiplier = 1
  1022. fan_always_on = 0
  1023. fan_below_layer_time = 20
  1024. filament_colour = #FF8000
  1025. filament_cooling_final_speed = 3.4
  1026. filament_cooling_initial_speed = 2.2
  1027. filament_cooling_moves = 4
  1028. filament_cost = 18.99
  1029. filament_density = 1.27
  1030. filament_deretract_speed = nil
  1031. filament_diameter = 1.7
  1032. filament_load_time = 0
  1033. filament_loading_speed = 28
  1034. filament_loading_speed_start = 3
  1035. filament_max_volumetric_speed = 6.5
  1036. filament_minimal_purge_on_wipe_tower = 5
  1037. filament_notes = "List of manufacturers tested with standard PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mlade? PETG\nInland PETG"
  1038. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1039. filament_retract_before_travel = nil
  1040. filament_retract_before_wipe = nil
  1041. filament_retract_layer_change = nil
  1042. filament_retract_length = nil
  1043. filament_retract_lift = nil
  1044. filament_retract_lift_above = nil
  1045. filament_retract_lift_below = nil
  1046. filament_retract_restart_extra = nil
  1047. filament_retract_speed = nil
  1048. filament_settings_id = ""
  1049. filament_soluble = 0
  1050. filament_toolchange_delay = 0
  1051. filament_type = PET
  1052. filament_unload_time = 0
  1053. filament_unloading_speed = 90
  1054. filament_unloading_speed_start = 100
  1055. filament_vendor = (Unknown)
  1056. filament_wipe = nil
  1057. first_layer_bed_temperature = 85
  1058. first_layer_temperature = 245
  1059. inherits =
  1060. max_fan_speed = 50
  1061. min_fan_speed = 30
  1062. min_print_speed = 10
  1063. slowdown_below_layer_time = 5
  1064. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  1065. temperature = 240
  1066.  
  1067. [filament:Inland PLA (RLG 20191006)]
  1068. bed_temperature = 55
  1069. bridge_fan_speed = 100
  1070. compatible_printers =
  1071. compatible_printers_condition =
  1072. compatible_prints =
  1073. compatible_prints_condition =
  1074. cooling = 1
  1075. disable_fan_first_layers = 1
  1076. end_filament_gcode = "; Filament-specific end gcode"
  1077. extrusion_multiplier = 1
  1078. fan_always_on = 1
  1079. fan_below_layer_time = 100
  1080. filament_colour = #DEDEE6
  1081. filament_cooling_final_speed = 3.4
  1082. filament_cooling_initial_speed = 2.2
  1083. filament_cooling_moves = 4
  1084. filament_cost = 17
  1085. filament_density = 1.27
  1086. filament_deretract_speed = nil
  1087. filament_diameter = 1.75
  1088. filament_load_time = 0
  1089. filament_loading_speed = 28
  1090. filament_loading_speed_start = 3
  1091. filament_max_volumetric_speed = 15
  1092. filament_minimal_purge_on_wipe_tower = 5
  1093. filament_notes = "List of materials tested:\n\nInland PLA"
  1094. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1095. filament_retract_before_travel = nil
  1096. filament_retract_before_wipe = nil
  1097. filament_retract_layer_change = nil
  1098. filament_retract_length = nil
  1099. filament_retract_lift = nil
  1100. filament_retract_lift_above = nil
  1101. filament_retract_lift_below = nil
  1102. filament_retract_restart_extra = nil
  1103. filament_retract_speed = nil
  1104. filament_settings_id = ""
  1105. filament_soluble = 0
  1106. filament_toolchange_delay = 0
  1107. filament_type = PLA
  1108. filament_unload_time = 0
  1109. filament_unloading_speed = 90
  1110. filament_unloading_speed_start = 100
  1111. filament_vendor = (Unknown)
  1112. filament_wipe = nil
  1113. first_layer_bed_temperature = 55
  1114. first_layer_temperature = 225
  1115. inherits =
  1116. max_fan_speed = 100
  1117. min_fan_speed = 100
  1118. min_print_speed = 10
  1119. slowdown_below_layer_time = 20
  1120. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1121. temperature = 220
  1122.  
  1123. [filament:Inland eAlFill (RLG 20180801)]
  1124. bed_temperature = 60
  1125. bridge_fan_speed = 100
  1126. compatible_printers =
  1127. compatible_printers_condition = nozzle_diameter[0]>0.35
  1128. compatible_prints =
  1129. compatible_prints_condition =
  1130. cooling = 1
  1131. disable_fan_first_layers = 1
  1132. end_filament_gcode = "; Filament-specific end gcode"
  1133. extrusion_multiplier = 95
  1134. fan_always_on = 1
  1135. fan_below_layer_time = 100
  1136. filament_colour = #A79698
  1137. filament_cooling_final_speed = 3.4
  1138. filament_cooling_initial_speed = 2.2
  1139. filament_cooling_moves = 4
  1140. filament_cost = 57.98
  1141. filament_density = 0
  1142. filament_deretract_speed = nil
  1143. filament_diameter = 1.75
  1144. filament_load_time = 0
  1145. filament_loading_speed = 28
  1146. filament_loading_speed_start = 3
  1147. filament_max_volumetric_speed = 10
  1148. filament_minimal_purge_on_wipe_tower = 5
  1149. filament_notes = ""
  1150. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1151. filament_retract_before_travel = nil
  1152. filament_retract_before_wipe = nil
  1153. filament_retract_layer_change = nil
  1154. filament_retract_length = nil
  1155. filament_retract_lift = nil
  1156. filament_retract_lift_above = nil
  1157. filament_retract_lift_below = nil
  1158. filament_retract_restart_extra = nil
  1159. filament_retract_speed = nil
  1160. filament_settings_id = ""
  1161. filament_soluble = 0
  1162. filament_toolchange_delay = 0
  1163. filament_type = PLA
  1164. filament_unload_time = 0
  1165. filament_unloading_speed = 90
  1166. filament_unloading_speed_start = 100
  1167. filament_vendor = (Unknown)
  1168. filament_wipe = nil
  1169. first_layer_bed_temperature = 60
  1170. first_layer_temperature = 210
  1171. inherits =
  1172. max_fan_speed = 100
  1173. min_fan_speed = 100
  1174. min_print_speed = 10
  1175. slowdown_below_layer_time = 5
  1176. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1177. temperature = 205
  1178.  
  1179. [filament:Inland eLastic TPE (RLG 20180627)]
  1180. bed_temperature = 60
  1181. bridge_fan_speed = 50
  1182. compatible_printers =
  1183. compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1
  1184. compatible_prints =
  1185. compatible_prints_condition =
  1186. cooling = 1
  1187. disable_fan_first_layers = 1
  1188. end_filament_gcode = "; Filament-specific end gcode"
  1189. extrusion_multiplier = 0.95
  1190. fan_always_on = 0
  1191. fan_below_layer_time = 20
  1192. filament_colour = #D21E2C
  1193. filament_cooling_final_speed = 3.4
  1194. filament_cooling_initial_speed = 2.2
  1195. filament_cooling_moves = 4
  1196. filament_cost = 34
  1197. filament_density = 1.2
  1198. filament_deretract_speed = nil
  1199. filament_diameter = 1.75
  1200. filament_load_time = 0
  1201. filament_loading_speed = 28
  1202. filament_loading_speed_start = 3
  1203. filament_max_volumetric_speed = 2.5
  1204. filament_minimal_purge_on_wipe_tower = 5
  1205. filament_notes = "Print temperature: 240-260C\nBuild plate temperature: 80-100C\nCooling: 0-50C\nSpeed: 30-50mm/s\nHeat resistance: 120C\n"
  1206. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1207. filament_retract_before_travel = nil
  1208. filament_retract_before_wipe = nil
  1209. filament_retract_layer_change = nil
  1210. filament_retract_length = nil
  1211. filament_retract_lift = nil
  1212. filament_retract_lift_above = nil
  1213. filament_retract_lift_below = nil
  1214. filament_retract_restart_extra = nil
  1215. filament_retract_speed = nil
  1216. filament_settings_id = ""
  1217. filament_soluble = 0
  1218. filament_toolchange_delay = 0
  1219. filament_type = TPE
  1220. filament_unload_time = 0
  1221. filament_unloading_speed = 90
  1222. filament_unloading_speed_start = 100
  1223. filament_vendor = (Unknown)
  1224. filament_wipe = nil
  1225. first_layer_bed_temperature = 60
  1226. first_layer_temperature = 230
  1227. inherits =
  1228. max_fan_speed = 50
  1229. min_fan_speed = 30
  1230. min_print_speed = 10
  1231. slowdown_below_layer_time = 5
  1232. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  1233. temperature = 230
  1234.  
  1235. [filament:Inland eLastic TPE - READ NOTES! (RLG 20200228)]
  1236. bed_temperature = 60
  1237. bridge_fan_speed = 60
  1238. compatible_printers =
  1239. compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1
  1240. compatible_prints =
  1241. compatible_prints_condition =
  1242. cooling = 1
  1243. disable_fan_first_layers = 1
  1244. end_filament_gcode = "; Filament-specific end gcode"
  1245. extrusion_multiplier = 0.95
  1246. fan_always_on = 0
  1247. fan_below_layer_time = 20
  1248. filament_colour = #D21E2C
  1249. filament_cooling_final_speed = 3.4
  1250. filament_cooling_initial_speed = 2.2
  1251. filament_cooling_moves = 4
  1252. filament_cost = 34
  1253. filament_density = 1.2
  1254. filament_deretract_speed = nil
  1255. filament_diameter = 1.75
  1256. filament_load_time = 0
  1257. filament_loading_speed = 28
  1258. filament_loading_speed_start = 3
  1259. filament_max_volumetric_speed = 10
  1260. filament_minimal_purge_on_wipe_tower = 5
  1261. filament_notes = "Print temperature: 240-260C\nBuild plate temperature: 80-100C\nCooling: 0-50C\nSpeed: 30-50mm/s\nHeat resistance: 120C\n\nThis profile is for use with the 3D Solex Matchless high-throughput nozzle. Drop maximum volumetric speed for other nozzles.\n"
  1262. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1263. filament_retract_before_travel = nil
  1264. filament_retract_before_wipe = nil
  1265. filament_retract_layer_change = nil
  1266. filament_retract_length = 0.2
  1267. filament_retract_lift = 0.2
  1268. filament_retract_lift_above = nil
  1269. filament_retract_lift_below = nil
  1270. filament_retract_restart_extra = nil
  1271. filament_retract_speed = nil
  1272. filament_settings_id = ""
  1273. filament_soluble = 0
  1274. filament_toolchange_delay = 0
  1275. filament_type = TPE
  1276. filament_unload_time = 0
  1277. filament_unloading_speed = 90
  1278. filament_unloading_speed_start = 100
  1279. filament_vendor = (Unknown)
  1280. filament_wipe = nil
  1281. first_layer_bed_temperature = 60
  1282. first_layer_temperature = 240
  1283. inherits =
  1284. max_fan_speed = 50
  1285. min_fan_speed = 30
  1286. min_print_speed = 10
  1287. slowdown_below_layer_time = 5
  1288. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  1289. temperature = 240
  1290.  
  1291. [filament:KVP N-Vire rPET (RLG 20190221)]
  1292. bed_temperature = 80
  1293. bridge_fan_speed = 50
  1294. compatible_printers =
  1295. compatible_printers_condition =
  1296. compatible_prints =
  1297. compatible_prints_condition =
  1298. cooling = 1
  1299. disable_fan_first_layers = 3
  1300. end_filament_gcode = "; Filament-specific end gcode"
  1301. extrusion_multiplier = 0.97
  1302. fan_always_on = 0
  1303. fan_below_layer_time = 30
  1304. filament_colour = #118002
  1305. filament_cooling_final_speed = 3.4
  1306. filament_cooling_initial_speed = 2.2
  1307. filament_cooling_moves = 4
  1308. filament_cost = 34.95
  1309. filament_density = 1.27
  1310. filament_deretract_speed = nil
  1311. filament_diameter = 1.7
  1312. filament_load_time = 0
  1313. filament_loading_speed = 28
  1314. filament_loading_speed_start = 3
  1315. filament_max_volumetric_speed = 8
  1316. filament_minimal_purge_on_wipe_tower = 5
  1317. filament_notes = "List of materials tested:\n\nKVP N-Vire rPET\n\nLA, extrusion rate, temp & diameter calibrated \n\nRecommended Printer Specifications\nOptimal Print Temp: 230ºC ? 260ºC\nOptimal Bed Temp: 70ºC ? 100ºC"
  1318. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1319. filament_retract_before_travel = nil
  1320. filament_retract_before_wipe = nil
  1321. filament_retract_layer_change = nil
  1322. filament_retract_length = nil
  1323. filament_retract_lift = nil
  1324. filament_retract_lift_above = nil
  1325. filament_retract_lift_below = nil
  1326. filament_retract_restart_extra = nil
  1327. filament_retract_speed = nil
  1328. filament_settings_id = ""
  1329. filament_soluble = 0
  1330. filament_toolchange_delay = 0
  1331. filament_type = PET
  1332. filament_unload_time = 0
  1333. filament_unloading_speed = 90
  1334. filament_unloading_speed_start = 100
  1335. filament_vendor = (Unknown)
  1336. filament_wipe = nil
  1337. first_layer_bed_temperature = 80
  1338. first_layer_temperature = 270
  1339. inherits =
  1340. max_fan_speed = 50
  1341. min_fan_speed = 30
  1342. min_print_speed = 10
  1343. slowdown_below_layer_time = 5
  1344. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  1345. temperature = 270
  1346.  
  1347. [filament:KVP PETG (RLG 20190227)]
  1348. bed_temperature = 80
  1349. bridge_fan_speed = 50
  1350. compatible_printers =
  1351. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1352. compatible_prints =
  1353. compatible_prints_condition =
  1354. cooling = 1
  1355. disable_fan_first_layers = 3
  1356. end_filament_gcode = "; Filament-specific end gcode"
  1357. extrusion_multiplier = 0.95
  1358. fan_always_on = 1
  1359. fan_below_layer_time = 20
  1360. filament_colour = #66CCFF
  1361. filament_cooling_final_speed = 3.4
  1362. filament_cooling_initial_speed = 2.2
  1363. filament_cooling_moves = 4
  1364. filament_cost = 53.99
  1365. filament_density = 1.27
  1366. filament_deretract_speed = nil
  1367. filament_diameter = 1.72
  1368. filament_load_time = 0
  1369. filament_loading_speed = 28
  1370. filament_loading_speed_start = 3
  1371. filament_max_volumetric_speed = 8
  1372. filament_minimal_purge_on_wipe_tower = 15
  1373. filament_notes = "List of manufacturers tested:\n\nKeene Village Plastics PETG\n\nLA, extrusion rate & diameter calibrated 20190226\n\nRecommended Printer Specifications\nOptimal Print Temp: 230ºC ? 260ºC\nOptimal Bed Temp: 70ºC ? 100ºC"
  1374. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1375. filament_retract_before_travel = nil
  1376. filament_retract_before_wipe = nil
  1377. filament_retract_layer_change = nil
  1378. filament_retract_length = nil
  1379. filament_retract_lift = nil
  1380. filament_retract_lift_above = nil
  1381. filament_retract_lift_below = nil
  1382. filament_retract_restart_extra = nil
  1383. filament_retract_speed = nil
  1384. filament_settings_id = ""
  1385. filament_soluble = 0
  1386. filament_toolchange_delay = 0
  1387. filament_type = PET
  1388. filament_unload_time = 0
  1389. filament_unloading_speed = 90
  1390. filament_unloading_speed_start = 100
  1391. filament_vendor = (Unknown)
  1392. filament_wipe = nil
  1393. first_layer_bed_temperature = 75
  1394. first_layer_temperature = 255
  1395. inherits =
  1396. max_fan_speed = 50
  1397. min_fan_speed = 30
  1398. min_print_speed = 10
  1399. slowdown_below_layer_time = 5
  1400. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  1401. temperature = 245
  1402.  
  1403. [filament:Mad Maker PLA (RLG 20190325)]
  1404. bed_temperature = 60
  1405. bridge_fan_speed = 100
  1406. compatible_printers =
  1407. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1408. compatible_prints =
  1409. compatible_prints_condition =
  1410. cooling = 1
  1411. disable_fan_first_layers = 1
  1412. end_filament_gcode = "; Filament-specific end gcode"
  1413. extrusion_multiplier = 0.94
  1414. fan_always_on = 1
  1415. fan_below_layer_time = 100
  1416. filament_colour = #FF3232
  1417. filament_cooling_final_speed = 3.4
  1418. filament_cooling_initial_speed = 2.2
  1419. filament_cooling_moves = 4
  1420. filament_cost = 21
  1421. filament_density = 1.27
  1422. filament_deretract_speed = nil
  1423. filament_diameter = 1.725
  1424. filament_load_time = 0
  1425. filament_loading_speed = 28
  1426. filament_loading_speed_start = 3
  1427. filament_max_volumetric_speed = 15
  1428. filament_minimal_purge_on_wipe_tower = 15
  1429. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nMakeShaper PLA\n\nLA, extrusion multiplier and diameter calibrated 20181120"
  1430. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1431. filament_retract_before_travel = nil
  1432. filament_retract_before_wipe = nil
  1433. filament_retract_layer_change = nil
  1434. filament_retract_length = nil
  1435. filament_retract_lift = nil
  1436. filament_retract_lift_above = nil
  1437. filament_retract_lift_below = nil
  1438. filament_retract_restart_extra = nil
  1439. filament_retract_speed = nil
  1440. filament_settings_id = ""
  1441. filament_soluble = 0
  1442. filament_toolchange_delay = 0
  1443. filament_type = PLA
  1444. filament_unload_time = 0
  1445. filament_unloading_speed = 90
  1446. filament_unloading_speed_start = 100
  1447. filament_vendor = (Unknown)
  1448. filament_wipe = nil
  1449. first_layer_bed_temperature = 65
  1450. first_layer_temperature = 205
  1451. inherits =
  1452. max_fan_speed = 100
  1453. min_fan_speed = 100
  1454. min_print_speed = 10
  1455. slowdown_below_layer_time = 15
  1456. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1457. temperature = 200
  1458.  
  1459. [filament:MakeShaper PLA (RLG20181120)]
  1460. bed_temperature = 55
  1461. bridge_fan_speed = 100
  1462. compatible_printers =
  1463. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1464. compatible_prints =
  1465. compatible_prints_condition =
  1466. cooling = 1
  1467. disable_fan_first_layers = 1
  1468. end_filament_gcode = "; Filament-specific end gcode"
  1469. extrusion_multiplier = 0.94
  1470. fan_always_on = 1
  1471. fan_below_layer_time = 100
  1472. filament_colour = #FF3232
  1473. filament_cooling_final_speed = 3.4
  1474. filament_cooling_initial_speed = 2.2
  1475. filament_cooling_moves = 4
  1476. filament_cost = 21
  1477. filament_density = 1.27
  1478. filament_deretract_speed = nil
  1479. filament_diameter = 1.725
  1480. filament_load_time = 0
  1481. filament_loading_speed = 28
  1482. filament_loading_speed_start = 3
  1483. filament_max_volumetric_speed = 15
  1484. filament_minimal_purge_on_wipe_tower = 15
  1485. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nMakeShaper PLA\n\nLA, extrusion multiplier and diameter calibrated 20181120"
  1486. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1487. filament_retract_before_travel = nil
  1488. filament_retract_before_wipe = nil
  1489. filament_retract_layer_change = nil
  1490. filament_retract_length = nil
  1491. filament_retract_lift = nil
  1492. filament_retract_lift_above = nil
  1493. filament_retract_lift_below = nil
  1494. filament_retract_restart_extra = nil
  1495. filament_retract_speed = nil
  1496. filament_settings_id = ""
  1497. filament_soluble = 0
  1498. filament_toolchange_delay = 0
  1499. filament_type = PLA
  1500. filament_unload_time = 0
  1501. filament_unloading_speed = 90
  1502. filament_unloading_speed_start = 100
  1503. filament_vendor = (Unknown)
  1504. filament_wipe = nil
  1505. first_layer_bed_temperature = 60
  1506. first_layer_temperature = 210
  1507. inherits =
  1508. max_fan_speed = 100
  1509. min_fan_speed = 100
  1510. min_print_speed = 10
  1511. slowdown_below_layer_time = 5
  1512. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1513. temperature = 205
  1514.  
  1515. [filament:Maker Geeks PLA (RLG 20181030)]
  1516. bed_temperature = 60
  1517. bridge_fan_speed = 100
  1518. compatible_printers =
  1519. compatible_printers_condition =
  1520. compatible_prints =
  1521. compatible_prints_condition =
  1522. cooling = 1
  1523. disable_fan_first_layers = 1
  1524. end_filament_gcode = "; Filament-specific end gcode"
  1525. extrusion_multiplier = 1.09
  1526. fan_always_on = 1
  1527. fan_below_layer_time = 100
  1528. filament_colour = #B0F11A
  1529. filament_cooling_final_speed = 3.4
  1530. filament_cooling_initial_speed = 2.2
  1531. filament_cooling_moves = 4
  1532. filament_cost = 0
  1533. filament_density = 0
  1534. filament_deretract_speed = nil
  1535. filament_diameter = 1.75
  1536. filament_load_time = 0
  1537. filament_loading_speed = 28
  1538. filament_loading_speed_start = 3
  1539. filament_max_volumetric_speed = 15
  1540. filament_minimal_purge_on_wipe_tower = 5
  1541. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mlade? PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
  1542. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1543. filament_retract_before_travel = nil
  1544. filament_retract_before_wipe = nil
  1545. filament_retract_layer_change = nil
  1546. filament_retract_length = nil
  1547. filament_retract_lift = nil
  1548. filament_retract_lift_above = nil
  1549. filament_retract_lift_below = nil
  1550. filament_retract_restart_extra = nil
  1551. filament_retract_speed = nil
  1552. filament_settings_id = ""
  1553. filament_soluble = 0
  1554. filament_toolchange_delay = 0
  1555. filament_type = PLA
  1556. filament_unload_time = 0
  1557. filament_unloading_speed = 90
  1558. filament_unloading_speed_start = 100
  1559. filament_vendor = (Unknown)
  1560. filament_wipe = nil
  1561. first_layer_bed_temperature = 60
  1562. first_layer_temperature = 230
  1563. inherits =
  1564. max_fan_speed = 100
  1565. min_fan_speed = 75
  1566. min_print_speed = 10
  1567. slowdown_below_layer_time = 5
  1568. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1569. temperature = 230
  1570.  
  1571. [filament:MatterHackers Ryno (RLG 20181214)]
  1572. bed_temperature = 65
  1573. bridge_fan_speed = 40
  1574. compatible_printers =
  1575. compatible_printers_condition =
  1576. compatible_prints =
  1577. compatible_prints_condition =
  1578. cooling = 1
  1579. disable_fan_first_layers = 3
  1580. end_filament_gcode = "; Filament-specific end gcode"
  1581. extrusion_multiplier = 1
  1582. fan_always_on = 0
  1583. fan_below_layer_time = 10
  1584. filament_colour = #14FA00
  1585. filament_cooling_final_speed = 3.4
  1586. filament_cooling_initial_speed = 2.2
  1587. filament_cooling_moves = 4
  1588. filament_cost = 64
  1589. filament_density = 0
  1590. filament_deretract_speed = nil
  1591. filament_diameter = 1.73
  1592. filament_load_time = 0
  1593. filament_loading_speed = 28
  1594. filament_loading_speed_start = 3
  1595. filament_max_volumetric_speed = 8
  1596. filament_minimal_purge_on_wipe_tower = 5
  1597. filament_notes = "List of materials tested:\n\nMatterHackers Ryno\n\nLA, extrusion multiplier and diameter calibrated 20181029\n"
  1598. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1599. filament_retract_before_travel = nil
  1600. filament_retract_before_wipe = nil
  1601. filament_retract_layer_change = nil
  1602. filament_retract_length = nil
  1603. filament_retract_lift = nil
  1604. filament_retract_lift_above = nil
  1605. filament_retract_lift_below = nil
  1606. filament_retract_restart_extra = nil
  1607. filament_retract_speed = nil
  1608. filament_settings_id = ""
  1609. filament_soluble = 0
  1610. filament_toolchange_delay = 0
  1611. filament_type = RYNO
  1612. filament_unload_time = 0
  1613. filament_unloading_speed = 90
  1614. filament_unloading_speed_start = 100
  1615. filament_vendor = (Unknown)
  1616. filament_wipe = nil
  1617. first_layer_bed_temperature = 65
  1618. first_layer_temperature = 230
  1619. inherits =
  1620. max_fan_speed = 50
  1621. min_fan_speed = 30
  1622. min_print_speed = 10
  1623. slowdown_below_layer_time = 5
  1624. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
  1625. temperature = 230
  1626.  
  1627. [filament:Matterhackers Build PLA (RLG 20200309)]
  1628. bed_temperature = 60
  1629. bridge_fan_speed = 100
  1630. compatible_printers =
  1631. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1632. compatible_prints =
  1633. compatible_prints_condition =
  1634. cooling = 1
  1635. disable_fan_first_layers = 1
  1636. end_filament_gcode = "; Filament-specific end gcode"
  1637. extrusion_multiplier = 1
  1638. fan_always_on = 1
  1639. fan_below_layer_time = 100
  1640. filament_colour = #FECC66
  1641. filament_cooling_final_speed = 3.4
  1642. filament_cooling_initial_speed = 2.2
  1643. filament_cooling_moves = 4
  1644. filament_cost = 25.4
  1645. filament_density = 1.24
  1646. filament_deretract_speed = nil
  1647. filament_diameter = 1.73
  1648. filament_load_time = 0
  1649. filament_loading_speed = 28
  1650. filament_loading_speed_start = 3
  1651. filament_max_volumetric_speed = 15
  1652. filament_minimal_purge_on_wipe_tower = 15
  1653. filament_notes = "List of materials tested:\n\nMatterHackers Build PLA\n\nLA, extrusion multiplier and diameter calibrated 20200308"
  1654. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1655. filament_retract_before_travel = nil
  1656. filament_retract_before_wipe = nil
  1657. filament_retract_layer_change = nil
  1658. filament_retract_length = nil
  1659. filament_retract_lift = nil
  1660. filament_retract_lift_above = nil
  1661. filament_retract_lift_below = nil
  1662. filament_retract_restart_extra = nil
  1663. filament_retract_speed = nil
  1664. filament_settings_id = ""
  1665. filament_soluble = 0
  1666. filament_toolchange_delay = 0
  1667. filament_type = PLA
  1668. filament_unload_time = 0
  1669. filament_unloading_speed = 90
  1670. filament_unloading_speed_start = 100
  1671. filament_vendor = Generic
  1672. filament_wipe = nil
  1673. first_layer_bed_temperature = 60
  1674. first_layer_temperature = 205
  1675. inherits = Generic PLA
  1676. max_fan_speed = 100
  1677. min_fan_speed = 100
  1678. min_print_speed = 15
  1679. slowdown_below_layer_time = 20
  1680. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}18{else}35`{endif} ; Filament gcode"
  1681. temperature = 205
  1682.  
  1683. [filament:Paramount PLA (RLG 20181210)]
  1684. bed_temperature = 55
  1685. bridge_fan_speed = 100
  1686. compatible_printers =
  1687. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
  1688. compatible_prints =
  1689. compatible_prints_condition =
  1690. cooling = 1
  1691. disable_fan_first_layers = 1
  1692. end_filament_gcode = "; Filament-specific end gcode"
  1693. extrusion_multiplier = 0.9
  1694. fan_always_on = 1
  1695. fan_below_layer_time = 100
  1696. filament_colour = #7F7F7E
  1697. filament_cooling_final_speed = 3.4
  1698. filament_cooling_initial_speed = 2.2
  1699. filament_cooling_moves = 4
  1700. filament_cost = 22.99
  1701. filament_density = 1.24
  1702. filament_deretract_speed = nil
  1703. filament_diameter = 1.715
  1704. filament_load_time = 0
  1705. filament_loading_speed = 28
  1706. filament_loading_speed_start = 3
  1707. filament_max_volumetric_speed = 15
  1708. filament_minimal_purge_on_wipe_tower = 15
  1709. filament_notes = "List of materials tested:\n\nParamount PLA\n\nLA, extrusion rate & diameter calibrated 20181005"
  1710. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1711. filament_retract_before_travel = nil
  1712. filament_retract_before_wipe = nil
  1713. filament_retract_layer_change = nil
  1714. filament_retract_length = nil
  1715. filament_retract_lift = nil
  1716. filament_retract_lift_above = nil
  1717. filament_retract_lift_below = nil
  1718. filament_retract_restart_extra = nil
  1719. filament_retract_speed = nil
  1720. filament_settings_id = ""
  1721. filament_soluble = 0
  1722. filament_toolchange_delay = 0
  1723. filament_type = PLA
  1724. filament_unload_time = 0
  1725. filament_unloading_speed = 90
  1726. filament_unloading_speed_start = 100
  1727. filament_vendor = (Unknown)
  1728. filament_wipe = nil
  1729. first_layer_bed_temperature = 55
  1730. first_layer_temperature = 210
  1731. inherits =
  1732. max_fan_speed = 100
  1733. min_fan_speed = 75
  1734. min_print_speed = 10
  1735. slowdown_below_layer_time = 5
  1736. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1737. temperature = 205
  1738.  
  1739. [filament:Polymaker PolyLite PETG (RLG 20190912)]
  1740. bed_temperature = 75
  1741. bridge_fan_speed = 50
  1742. compatible_printers =
  1743. compatible_printers_condition =
  1744. compatible_prints =
  1745. compatible_prints_condition =
  1746. cooling = 1
  1747. disable_fan_first_layers = 3
  1748. end_filament_gcode = "; Filament-specific end gcode"
  1749. extrusion_multiplier = 1.14
  1750. fan_always_on = 0
  1751. fan_below_layer_time = 20
  1752. filament_colour = #108080
  1753. filament_cooling_final_speed = 3.4
  1754. filament_cooling_initial_speed = 2.2
  1755. filament_cooling_moves = 4
  1756. filament_cost = 24.99
  1757. filament_density = 1.23
  1758. filament_deretract_speed = nil
  1759. filament_diameter = 1.74
  1760. filament_load_time = 0
  1761. filament_loading_speed = 28
  1762. filament_loading_speed_start = 3
  1763. filament_max_volumetric_speed = 6.5
  1764. filament_minimal_purge_on_wipe_tower = 5
  1765. filament_notes = "List of manufacturers tested with standard PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mlade? PETG\nInland PETG"
  1766. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1767. filament_retract_before_travel = nil
  1768. filament_retract_before_wipe = nil
  1769. filament_retract_layer_change = nil
  1770. filament_retract_length = nil
  1771. filament_retract_lift = nil
  1772. filament_retract_lift_above = nil
  1773. filament_retract_lift_below = nil
  1774. filament_retract_restart_extra = nil
  1775. filament_retract_speed = nil
  1776. filament_settings_id = ""
  1777. filament_soluble = 0
  1778. filament_toolchange_delay = 0
  1779. filament_type = PET
  1780. filament_unload_time = 0
  1781. filament_unloading_speed = 90
  1782. filament_unloading_speed_start = 100
  1783. filament_vendor = (Unknown)
  1784. filament_wipe = nil
  1785. first_layer_bed_temperature = 80
  1786. first_layer_temperature = 235
  1787. inherits =
  1788. max_fan_speed = 50
  1789. min_fan_speed = 30
  1790. min_print_speed = 10
  1791. slowdown_below_layer_time = 5
  1792. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}70{endif}; Filament gcode\nM900 W[extrusion_width] H[layer_height] D[filament_diameter]\n"
  1793. temperature = 240
  1794.  
  1795. [filament:PrintedSolid Marble PLA (RLG 20180702)]
  1796. bed_temperature = 60
  1797. bridge_fan_speed = 100
  1798. compatible_printers =
  1799. compatible_printers_condition =
  1800. compatible_prints =
  1801. compatible_prints_condition =
  1802. cooling = 1
  1803. disable_fan_first_layers = 1
  1804. end_filament_gcode = "; Filament-specific end gcode"
  1805. extrusion_multiplier = 1
  1806. fan_always_on = 1
  1807. fan_below_layer_time = 100
  1808. filament_colour = #6B6A6C
  1809. filament_cooling_final_speed = 3.4
  1810. filament_cooling_initial_speed = 2.2
  1811. filament_cooling_moves = 4
  1812. filament_cost = 22.5
  1813. filament_density = 0
  1814. filament_deretract_speed = nil
  1815. filament_diameter = 1.75
  1816. filament_load_time = 0
  1817. filament_loading_speed = 28
  1818. filament_loading_speed_start = 3
  1819. filament_max_volumetric_speed = 8
  1820. filament_minimal_purge_on_wipe_tower = 5
  1821. filament_notes = "List of materials tested:\n\nPrintedSolid Marble PLA\nNozzle temperature: 190-210C\nBed temperature: 0-60C"
  1822. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1823. filament_retract_before_travel = nil
  1824. filament_retract_before_wipe = nil
  1825. filament_retract_layer_change = nil
  1826. filament_retract_length = nil
  1827. filament_retract_lift = nil
  1828. filament_retract_lift_above = nil
  1829. filament_retract_lift_below = nil
  1830. filament_retract_restart_extra = nil
  1831. filament_retract_speed = nil
  1832. filament_settings_id = ""
  1833. filament_soluble = 0
  1834. filament_toolchange_delay = 0
  1835. filament_type = PLA
  1836. filament_unload_time = 0
  1837. filament_unloading_speed = 90
  1838. filament_unloading_speed_start = 100
  1839. filament_vendor = (Unknown)
  1840. filament_wipe = nil
  1841. first_layer_bed_temperature = 65
  1842. first_layer_temperature = 225
  1843. inherits =
  1844. max_fan_speed = 100
  1845. min_fan_speed = 100
  1846. min_print_speed = 10
  1847. slowdown_below_layer_time = 5
  1848. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1849. temperature = 210
  1850.  
  1851. [filament:Prusa PLA (RLG 20181103)]
  1852. bed_temperature = 60
  1853. bridge_fan_speed = 100
  1854. compatible_printers =
  1855. compatible_printers_condition =
  1856. compatible_prints =
  1857. compatible_prints_condition =
  1858. cooling = 1
  1859. disable_fan_first_layers = 1
  1860. end_filament_gcode = "; Filament-specific end gcode"
  1861. extrusion_multiplier = 0.92
  1862. fan_always_on = 1
  1863. fan_below_layer_time = 100
  1864. filament_colour = #FF3232
  1865. filament_cooling_final_speed = 3.4
  1866. filament_cooling_initial_speed = 2.2
  1867. filament_cooling_moves = 4
  1868. filament_cost = 0
  1869. filament_density = 0
  1870. filament_deretract_speed = nil
  1871. filament_diameter = 1.715
  1872. filament_load_time = 0
  1873. filament_loading_speed = 28
  1874. filament_loading_speed_start = 3
  1875. filament_max_volumetric_speed = 15
  1876. filament_minimal_purge_on_wipe_tower = 5
  1877. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mlade? PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH\n\nLA, extrusion rate & diameter calibrated 20181005"
  1878. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1879. filament_retract_before_travel = nil
  1880. filament_retract_before_wipe = nil
  1881. filament_retract_layer_change = nil
  1882. filament_retract_length = nil
  1883. filament_retract_lift = nil
  1884. filament_retract_lift_above = nil
  1885. filament_retract_lift_below = nil
  1886. filament_retract_restart_extra = nil
  1887. filament_retract_speed = nil
  1888. filament_settings_id = ""
  1889. filament_soluble = 0
  1890. filament_toolchange_delay = 0
  1891. filament_type = PLA
  1892. filament_unload_time = 0
  1893. filament_unloading_speed = 90
  1894. filament_unloading_speed_start = 100
  1895. filament_vendor = (Unknown)
  1896. filament_wipe = nil
  1897. first_layer_bed_temperature = 60
  1898. first_layer_temperature = 200
  1899. inherits =
  1900. max_fan_speed = 100
  1901. min_fan_speed = 75
  1902. min_print_speed = 10
  1903. slowdown_below_layer_time = 5
  1904. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1905. temperature = 200
  1906.  
  1907. [filament:RePLAy 3D Recycled PLA (RLG 20200302)]
  1908. bed_temperature = 65
  1909. bridge_fan_speed = 100
  1910. compatible_printers =
  1911. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1912. compatible_prints =
  1913. compatible_prints_condition =
  1914. cooling = 1
  1915. disable_fan_first_layers = 1
  1916. end_filament_gcode = "; Filament-specific end gcode"
  1917. extrusion_multiplier = 0.98
  1918. fan_always_on = 1
  1919. fan_below_layer_time = 100
  1920. filament_colour = #323232
  1921. filament_cooling_final_speed = 3.4
  1922. filament_cooling_initial_speed = 2.2
  1923. filament_cooling_moves = 4
  1924. filament_cost = 24.99
  1925. filament_density = 1.24
  1926. filament_deretract_speed = nil
  1927. filament_diameter = 1.7
  1928. filament_load_time = 0
  1929. filament_loading_speed = 28
  1930. filament_loading_speed_start = 3
  1931. filament_max_volumetric_speed = 15
  1932. filament_minimal_purge_on_wipe_tower = 15
  1933. filament_notes = "List of materials tested:\n\nRePLAy 3D Recycled PLA\n\nLA, extrusion rate & diameter calibrated 201811223"
  1934. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1935. filament_retract_before_travel = nil
  1936. filament_retract_before_wipe = nil
  1937. filament_retract_layer_change = nil
  1938. filament_retract_length = nil
  1939. filament_retract_lift = nil
  1940. filament_retract_lift_above = nil
  1941. filament_retract_lift_below = nil
  1942. filament_retract_restart_extra = nil
  1943. filament_retract_speed = nil
  1944. filament_settings_id = ""
  1945. filament_soluble = 0
  1946. filament_toolchange_delay = 0
  1947. filament_type = PLA
  1948. filament_unload_time = 0
  1949. filament_unloading_speed = 90
  1950. filament_unloading_speed_start = 100
  1951. filament_vendor = (Unknown)
  1952. filament_wipe = nil
  1953. first_layer_bed_temperature = 65
  1954. first_layer_temperature = 205
  1955. inherits =
  1956. max_fan_speed = 100
  1957. min_fan_speed = 100
  1958. min_print_speed = 10
  1959. slowdown_below_layer_time = 5
  1960. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  1961. temperature = 200
  1962.  
  1963. [filament:SpiderMaker PLA (RLG 20190911)]
  1964. bed_temperature = 60
  1965. bridge_fan_speed = 100
  1966. compatible_printers =
  1967. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  1968. compatible_prints =
  1969. compatible_prints_condition =
  1970. cooling = 1
  1971. disable_fan_first_layers = 1
  1972. end_filament_gcode = "; Filament-specific end gcode"
  1973. extrusion_multiplier = 1.15
  1974. fan_always_on = 1
  1975. fan_below_layer_time = 100
  1976. filament_colour = #66CCFF
  1977. filament_cooling_final_speed = 3.4
  1978. filament_cooling_initial_speed = 2.2
  1979. filament_cooling_moves = 4
  1980. filament_cost = 49.32
  1981. filament_density = 1.27
  1982. filament_deretract_speed = nil
  1983. filament_diameter = 1.725
  1984. filament_load_time = 0
  1985. filament_loading_speed = 28
  1986. filament_loading_speed_start = 3
  1987. filament_max_volumetric_speed = 15
  1988. filament_minimal_purge_on_wipe_tower = 15
  1989. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nMakeShaper PLA\n\nLA, extrusion multiplier and diameter calibrated 20181120"
  1990. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  1991. filament_retract_before_travel = nil
  1992. filament_retract_before_wipe = nil
  1993. filament_retract_layer_change = nil
  1994. filament_retract_length = nil
  1995. filament_retract_lift = nil
  1996. filament_retract_lift_above = nil
  1997. filament_retract_lift_below = nil
  1998. filament_retract_restart_extra = nil
  1999. filament_retract_speed = nil
  2000. filament_settings_id = ""
  2001. filament_soluble = 0
  2002. filament_toolchange_delay = 0
  2003. filament_type = PLA
  2004. filament_unload_time = 0
  2005. filament_unloading_speed = 90
  2006. filament_unloading_speed_start = 100
  2007. filament_vendor = (Unknown)
  2008. filament_wipe = nil
  2009. first_layer_bed_temperature = 65
  2010. first_layer_temperature = 200
  2011. inherits =
  2012. max_fan_speed = 100
  2013. min_fan_speed = 100
  2014. min_print_speed = 10
  2015. slowdown_below_layer_time = 15
  2016. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode"
  2017. temperature = 195
  2018.  
  2019. [filament:Toner Plastics PLA (RLG 20190626)]
  2020. bed_temperature = 60
  2021. bridge_fan_speed = 100
  2022. compatible_printers =
  2023. compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
  2024. compatible_prints =
  2025. compatible_prints_condition =
  2026. cooling = 1
  2027. disable_fan_first_layers = 1
  2028. end_filament_gcode = "; Filament-specific end gcode"
  2029. extrusion_multiplier = 0.9
  2030. fan_always_on = 1
  2031. fan_below_layer_time = 100
  2032. filament_colour = #FF3232
  2033. filament_cooling_final_speed = 3.4
  2034. filament_cooling_initial_speed = 2.2
  2035. filament_cooling_moves = 4
  2036. filament_cost = 19
  2037. filament_density = 1.27
  2038. filament_deretract_speed = nil
  2039. filament_diameter = 1.63
  2040. filament_load_time = 0
  2041. filament_loading_speed = 28
  2042. filament_loading_speed_start = 3
  2043. filament_max_volumetric_speed = 15
  2044. filament_minimal_purge_on_wipe_tower = 15
  2045. filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mlade? PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
  2046. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  2047. filament_retract_before_travel = nil
  2048. filament_retract_before_wipe = nil
  2049. filament_retract_layer_change = nil
  2050. filament_retract_length = nil
  2051. filament_retract_lift = nil
  2052. filament_retract_lift_above = nil
  2053. filament_retract_lift_below = nil
  2054. filament_retract_restart_extra = nil
  2055. filament_retract_speed = nil
  2056. filament_settings_id = ""
  2057. filament_soluble = 0
  2058. filament_toolchange_delay = 0
  2059. filament_type = PLA
  2060. filament_unload_time = 0
  2061. filament_unloading_speed = 90
  2062. filament_unloading_speed_start = 100
  2063. filament_vendor = (Unknown)
  2064. filament_wipe = nil
  2065. first_layer_bed_temperature = 60
  2066. first_layer_temperature = 215
  2067. inherits = Generic PLA
  2068. max_fan_speed = 100
  2069. min_fan_speed = 100
  2070. min_print_speed = 10
  2071. slowdown_below_layer_time = 5
  2072. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
  2073. temperature = 210
  2074.  
  2075. [filament:eSun PLA+ (RLG 20190517)]
  2076. bed_temperature = 55
  2077. bridge_fan_speed = 100
  2078. compatible_printers =
  2079. compatible_printers_condition =
  2080. compatible_prints =
  2081. compatible_prints_condition =
  2082. cooling = 1
  2083. disable_fan_first_layers = 1
  2084. end_filament_gcode = "; Filament-specific end gcode"
  2085. extrusion_multiplier = 0.9
  2086. fan_always_on = 1
  2087. fan_below_layer_time = 100
  2088. filament_colour = #FA7414
  2089. filament_cooling_final_speed = 3.4
  2090. filament_cooling_initial_speed = 2.2
  2091. filament_cooling_moves = 4
  2092. filament_cost = 22.99
  2093. filament_density = 1.2
  2094. filament_deretract_speed = nil
  2095. filament_diameter = 1.703
  2096. filament_load_time = 0
  2097. filament_loading_speed = 28
  2098. filament_loading_speed_start = 3
  2099. filament_max_volumetric_speed = 15
  2100. filament_minimal_purge_on_wipe_tower = 5
  2101. filament_notes = ""
  2102. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  2103. filament_retract_before_travel = nil
  2104. filament_retract_before_wipe = nil
  2105. filament_retract_layer_change = nil
  2106. filament_retract_length = nil
  2107. filament_retract_lift = nil
  2108. filament_retract_lift_above = nil
  2109. filament_retract_lift_below = nil
  2110. filament_retract_restart_extra = nil
  2111. filament_retract_speed = nil
  2112. filament_settings_id = ""
  2113. filament_soluble = 0
  2114. filament_toolchange_delay = 0
  2115. filament_type = PLA
  2116. filament_unload_time = 0
  2117. filament_unloading_speed = 90
  2118. filament_unloading_speed_start = 100
  2119. filament_vendor = (Unknown)
  2120. filament_wipe = nil
  2121. first_layer_bed_temperature = 55
  2122. first_layer_temperature = 210
  2123. inherits =
  2124. max_fan_speed = 100
  2125. min_fan_speed = 100
  2126. min_print_speed = 10
  2127. slowdown_below_layer_time = 5
  2128. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}40{endif}; Filament gcode"
  2129. temperature = 210
  2130.  
  2131. [filament:eSun Wood (RLG 20180624)]
  2132. bed_temperature = 60
  2133. bridge_fan_speed = 100
  2134. compatible_printers =
  2135. compatible_printers_condition = nozzle_diameter[0]>0.35
  2136. compatible_prints =
  2137. compatible_prints_condition =
  2138. cooling = 1
  2139. disable_fan_first_layers = 1
  2140. end_filament_gcode = "; Filament-specific end gcode"
  2141. extrusion_multiplier = 1.2
  2142. fan_always_on = 1
  2143. fan_below_layer_time = 100
  2144. filament_colour = #804040
  2145. filament_cooling_final_speed = 3.4
  2146. filament_cooling_initial_speed = 2.2
  2147. filament_cooling_moves = 4
  2148. filament_cost = 59.88
  2149. filament_density = 0
  2150. filament_deretract_speed = nil
  2151. filament_diameter = 1.75
  2152. filament_load_time = 0
  2153. filament_loading_speed = 28
  2154. filament_loading_speed_start = 3
  2155. filament_max_volumetric_speed = 10
  2156. filament_minimal_purge_on_wipe_tower = 5
  2157. filament_notes = "Print temperature: 190-220C\n"
  2158. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  2159. filament_retract_before_travel = nil
  2160. filament_retract_before_wipe = nil
  2161. filament_retract_layer_change = nil
  2162. filament_retract_length = nil
  2163. filament_retract_lift = nil
  2164. filament_retract_lift_above = nil
  2165. filament_retract_lift_below = nil
  2166. filament_retract_restart_extra = nil
  2167. filament_retract_speed = nil
  2168. filament_settings_id = ""
  2169. filament_soluble = 0
  2170. filament_toolchange_delay = 0
  2171. filament_type = PLA
  2172. filament_unload_time = 0
  2173. filament_unloading_speed = 90
  2174. filament_unloading_speed_start = 100
  2175. filament_vendor = (Unknown)
  2176. filament_wipe = nil
  2177. first_layer_bed_temperature = 60
  2178. first_layer_temperature = 215
  2179. inherits =
  2180. max_fan_speed = 100
  2181. min_fan_speed = 100
  2182. min_print_speed = 10
  2183. slowdown_below_layer_time = 5
  2184. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
  2185. temperature = 215
  2186.  
  2187. [filament:rigid.ink PLA (RLG 20181030)]
  2188. bed_temperature = 45
  2189. bridge_fan_speed = 100
  2190. compatible_printers =
  2191. compatible_printers_condition =
  2192. compatible_prints =
  2193. compatible_prints_condition =
  2194. cooling = 1
  2195. disable_fan_first_layers = 1
  2196. end_filament_gcode = "; Filament-specific end gcode"
  2197. extrusion_multiplier = 0.98
  2198. fan_always_on = 1
  2199. fan_below_layer_time = 100
  2200. filament_colour = #FA7414
  2201. filament_cooling_final_speed = 3.4
  2202. filament_cooling_initial_speed = 2.2
  2203. filament_cooling_moves = 4
  2204. filament_cost = 42.1
  2205. filament_density = 1.2
  2206. filament_deretract_speed = nil
  2207. filament_diameter = 1.73
  2208. filament_load_time = 0
  2209. filament_loading_speed = 28
  2210. filament_loading_speed_start = 3
  2211. filament_max_volumetric_speed = 15
  2212. filament_minimal_purge_on_wipe_tower = 5
  2213. filament_notes = "List of materials tested:\n\nrigid.ink PLA\n\nLA, extrusion rate & diameter calibrated 20181005\n\n"
  2214. filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  2215. filament_retract_before_travel = nil
  2216. filament_retract_before_wipe = nil
  2217. filament_retract_layer_change = nil
  2218. filament_retract_length = nil
  2219. filament_retract_lift = nil
  2220. filament_retract_lift_above = nil
  2221. filament_retract_lift_below = nil
  2222. filament_retract_restart_extra = nil
  2223. filament_retract_speed = nil
  2224. filament_settings_id = ""
  2225. filament_soluble = 0
  2226. filament_toolchange_delay = 0
  2227. filament_type = PLA
  2228. filament_unload_time = 0
  2229. filament_unloading_speed = 90
  2230. filament_unloading_speed_start = 100
  2231. filament_vendor = (Unknown)
  2232. filament_wipe = nil
  2233. first_layer_bed_temperature = 45
  2234. first_layer_temperature = 190
  2235. inherits =
  2236. max_fan_speed = 100
  2237. min_fan_speed = 75
  2238. min_print_speed = 10
  2239. slowdown_below_layer_time = 5
  2240. start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}28{endif}; Filament gcode\nM302 S180 ; Sets the minimum temp to 180C"
  2241. temperature = 190
RAW Paste Data