Guest User

Untitled

a guest
Dec 23rd, 2016
44
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot 1.1.3 (Jul 16 2010 - 11:25:10) (ALPHA)
  2. SVN revision: 359
  3. Target board: WRG-ND08
  4.  
  5. Board: Ralink APSoC DRAM: 32 MB
  6. Flash: Bank 0, ID:000322a8, Size 4194304 (0x00400000)
  7. ============================================
  8. Ralink UBoot Version: 3.3
  9. --------------------------------------------
  10. ASIC 3883_MP (MAC to MAC 100F MII Mode)
  11. DRAM component: 256 Mbits SDR
  12. DRAM bus: 16 bit
  13. Total memory: 32 MBytes
  14. Flash component: NOR Flash
  15. Date:Jul 16 2010 Time:11:25:10
  16. ============================================
  17. icache: sets:512, ways:4, linesz:32 ,total:65536
  18. dcache: sets:256, ways:4, linesz:32 ,total:32768
  19.  
  20. GPIO pin 24 reset to switch
  21.  
  22. Please choose the operation:
  23. 1: Load system code to SDRAM via TFTP.
  24. 2: Load system code then write to Flash via TFTP.
  25. 3: Boot system code via Flash (default).
  26. 4: Entr boot command line interface.
  27. 7: Load Boot Loader code then write to Flash via Serial.
  28. 9: Load Boot Loader code then write to Flash via TFTP. 0
  29.  
  30. 3: System Boot system code via Flash.
  31. ## Booting image at bc050000 ...
  32. We have SEAMA, Image Size = 1310656
  33. Verifying Checksum ...
  34. Uncompressing SEAMA linux.lzma ... OK
  35. ## Transferring control to Linux (at address bc05000c) ...
  36. ## Giving linux memsize in MB, 32
  37.  
  38. Starting kernel ...
  39.  
  40. [ 0.000000] Linux version 4.4.14 (bracco@bracco-VirtualBox) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50019) ) #27 Fri Dec 23 14:54:02 UTC 2016
  41. [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
  42. [ 0.000000] bootconsole [early0] enabled
  43. [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
  44. [ 0.000000] MIPS: machine is D-Link DIR-815 A1
  45. [ 0.000000] Determined physical RAM map:
  46. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  47. [ 0.000000] Initrd not found or empty - disabling initrd
  48. [ 0.000000] Zone ranges:
  49. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
  50. [ 0.000000] Movable zone start for each node
  51. [ 0.000000] Early memory node ranges
  52. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
  53. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
  54. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  55. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  56. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  57. [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
  58. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  59. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  60. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  61. [ 0.000000] Writing ErrCtl register=00000000
  62. [ 0.000000] Readback ErrCtl register=00000000
  63. [ 0.000000] Memory: 28288K/32768K available (2883K kernel code, 133K rwdata, 712K rodata, 168K init, 195K bss, 4480K reserved, 0K cma-reserved)
  64. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  65. [ 0.000000] NR_IRQS:256
  66. [ 0.000000] CPU Clock: 500MHz
  67. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
  68. [ 0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
  69. [ 0.015488] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
  70. [ 0.090664] pid_max: default: 32768 minimum: 301
  71. [ 0.100002] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  72. [ 0.113028] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  73. [ 0.134679] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  74. [ 0.154425] pinctrl core: initialized pinctrl subsystem
  75. [ 0.165629] NET: Registered protocol family 16
  76. [ 0.181629] rt3883-pci 10140000.pci: mode: PCIe
  77. [ 1.781350] PCI host bridge /pci@10140000/host-bridge ranges:
  78. [ 1.792685] MEM 0x0000000020000000..0x000000002fffffff
  79. [ 1.803035] IO 0x0000000010160000..0x000000001016ffff
  80. [ 1.828353] rt2880_gpio 10000600.gpio: registering 24 gpios
  81. [ 1.839438] rt2880_gpio 10000600.gpio: registering 24 irq handlers
  82. [ 1.851904] rt2880_gpio 10000638.gpio: registering 16 gpios
  83. [ 1.864062] PCI host bridge to bus 0000:00
  84. [ 1.872069] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
  85. [ 1.885808] pci_bus 0000:00: root bus resource [io 0xffffffff]
  86. [ 1.897517] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  87. [ 1.911010] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  88. [ 1.927371] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  89. [ 1.944102] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
  90. [ 1.957535] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
  91. [ 1.970992] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
  92. [ 1.984479] pci 0000:00:01.0: PCI bridge to [bus 01]
  93. [ 1.994323] pci 0000:00:01.0: bridge window [mem 0x20000000-0x200fffff]
  94. [ 2.007940] pci 0000:00:01.0: of_irq_parse_pci() failed with rc=-22
  95. [ 2.021714] clocksource: Switched to clocksource MIPS
  96. [ 2.033784] NET: Registered protocol family 2
  97. [ 2.043598] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  98. [ 2.057436] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  99. [ 2.069996] TCP: Hash tables configured (established 1024 bind 1024)
  100. [ 2.082826] UDP hash table entries: 256 (order: 0, 4096 bytes)
  101. [ 2.094382] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  102. [ 2.107302] NET: Registered protocol family 1
  103. [ 2.116675] rt-timer 10000100.timer: maximum frequency is 3814Hz
  104. [ 2.129855] futex hash table entries: 256 (order: -1, 3072 bytes)
  105. [ 2.172017] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  106. [ 2.183534] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  107. [ 2.207229] io scheduler noop registered
  108. [ 2.214998] io scheduler deadline registered (default)
  109. [ 2.225457] ralink-usb-phy usbphy: invalid resource
  110. [ 2.236034] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  111. [ 2.250206] console [ttyS0] disabled
  112. [ 2.257315] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
  113. [ 2.276957] console [ttyS0] enabled
  114. [ 2.276957] console [ttyS0] enabled
  115. [ 2.290749] bootconsole [early0] disabled
  116. [ 2.290749] bootconsole [early0] disabled
  117. [ 2.308181] 1c000000.nor-flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
  118. [ 2.329305] Amd/Fujitsu Extended Query Table at 0x0040
  119. [ 2.339568] Amd/Fujitsu Extended Query version 1.1.
  120. [ 2.349641] number of CFI chips: 1
  121. [ 2.360352] 6 ofpart partitions found on MTD device 1c000000.nor-flash
  122. [ 2.373469] Creating 6 MTD partitions on "1c000000.nor-flash":
  123. [ 2.385121] 0x000000000000-0x000000030000 : "uboot"
  124. [ 2.397312] 0x000000030000-0x000000034000 : "uboot-env"
  125. [ 2.410495] 0x000000034000-0x000000038000 : "factory"
  126. [ 2.423383] 0x000000038000-0x000000040000 : "nvram"
  127. [ 2.435833] 0x000000040000-0x000000050000 : "devdata"
  128. [ 2.448691] 0x000000050000-0x000000400000 : "firmware"
  129. [ 2.463969] 2 seama-fw partitions found on MTD device firmware
  130. [ 2.475692] 0x000000050040-0x000000190000 : "kernel"
  131. [ 2.488110] 0x000000190000-0x000000400000 : "rootfs"
  132. [ 2.500730] mtd: device 7 (rootfs) set to be root filesystem
  133. [ 2.512157] 1 squashfs-split partitions found on MTD device rootfs
  134. [ 2.524504] 0x0000003b0000-0x000000400000 : "rootfs_data"
  135. [ 2.541109] libphy: mdio: probed
  136. [ 2.550125] IP17xx: Found IP175D at mdio-bus:00
  137. [ 2.637951] mtk_soc_eth 10100000.ethernet: connected port 0 to PHY at mdio-bus:00 [uid=02430d80, driver=IC+ IP17xx]
  138. [ 2.659824] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
  139. [ 2.677210] rt2880_wdt 10000120.watchdog: Initialized
  140. [ 2.689300] NET: Registered protocol family 10
  141. [ 2.703922] NET: Registered protocol family 17
  142. [ 2.713035] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  143. [ 2.738218] 8021q: 802.1Q VLAN Support v1.8
  144. [ 2.753984] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
  145. [ 2.770151] Freeing unused kernel memory: 168K (803a6000 - 803d0000)
  146. [ 3.660511] init: Console is alive
  147. [ 3.667785] init: - watchdog -
  148. [ 4.466239] usbcore: registered new interface driver usbfs
  149. [ 4.477426] usbcore: registered new interface driver hub
  150. [ 4.488241] usbcore: registered new device driver usb
  151. [ 4.508042] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  152. [ 4.523803] ehci-platform: EHCI generic platform driver
  153. [ 4.539486] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  154. [ 4.554145] ohci-platform: OHCI generic platform driver
  155. [ 4.575893] init: - preinit -
  156. [ 5.114765] 8021q: adding VLAN 0 to HW filter on device eth0
  157. [ 5.157118] random: procd urandom read with 8 bits of entropy available
  158. Press the [f] key and hit [enter] to enter failsafe mode
  159. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  160. [ 6.781753] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
  161. [ 7.362088] jffs2: notice: (330) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  162. [ 7.394613] mount_root: switching to jffs2 overlay
  163. [ 7.448204] procd: - early -
  164. [ 7.454256] procd: - watchdog -
  165. [ 7.781756] mtk_soc_eth 10100000.ethernet eth0: link down
  166. [ 8.161896] procd: - ubus -
  167. [ 8.268195] procd: - init -
  168. Please press Enter to activate this console.
  169. [ 9.459957] ip6_tables: (C) 2000-2006 Netfilter Core Team
  170. [ 9.492937] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
  171. [ 9.508108] Backport generated by backports.git backports-20160216-0-ge3c56e4
  172. [ 9.529288] ip_tables: (C) 2000-2006 Netfilter Core Team
  173. [ 9.557124] nf_conntrack version 0.5.0 (444 buckets, 1776 max)
  174. [ 9.627813] xt_time: kernel timezone is -0000
  175. [ 9.735247] PPP generic driver version 2.4.2
  176. [ 9.748348] NET: Registered protocol family 24
  177. [ 9.803838] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
  178. [ 9.815470] rt2800pci 0000:01:00.0: failed to load eeprom property
  179. [ 9.827851] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00pci_1_0.eeprom'.
  180. [ 9.853519] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected
  181. [ 9.869049] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
  182. [ 9.914817] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected
  183. [ 9.930392] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected
  184. [ 19.963738] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  185. [ 19.975476] 8021q: adding VLAN 0 to HW filter on device eth0
  186. [ 20.025348] device eth0.1 entered promiscuous mode
  187. [ 20.035027] device eth0 entered promiscuous mode
  188. [ 20.095637] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  189. [ 20.183245] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
  190. [ 20.891898] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
  191. [ 21.002345] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  192. [ 21.061981] br-lan: port 1(eth0.1) entered forwarding state
  193. [ 21.073246] br-lan: port 1(eth0.1) entered forwarding state
  194. [ 21.084873] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
  195. [ 21.161392] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  196. [ 23.071719] br-lan: port 1(eth0.1) entered forwarding state
RAW Paste Data