1.               Product Specifications :

Project

Index

Power Supply

DC 12VDC + 10 %; Current 1.2A

Lock Relay

DC 12VDC/2A

Ambient temperature

Working: -20 ℃ ~ 45 ℃ ; Storage: -10 ℃ ~ 55 ℃

Effective storage capacity card

500 sheets, each valid card at the same time have a "personal password"

4 universal password Capacity

Group 1

Reader firing frequency

125HKz

Proximity card identification

EM or EM compatible card

Read Range

5-15CM

Open method

Class 2 (or universal password card + card with a PIN)

2. Functions and settings: (any settings on the controller must be in programming mode)

1 ). Enter the programming mode:

　　Press [ * ] + [6 programming password], two beeps sound, (red light flashing, green light. factory programming password is 990101 , user access control enabled device, be sure to modify the programming code. If the 20 seconds no programming instructions within the system automatically exit programming mode.)

2 ). Modify the programming password:

　　Press [ 0 ] + [ 6 digits new programming PIN] + [repeat 6 digits new programming PIN], two beeps sound; indicating setting.

3 ) Set open mode:

  ① . cards or universal password: Press [1] + [0] , two beeps sound;

  ②. Calgary individuals Password: press [1] + [1] , two beeps sound;

4 ) set the opening hours:

  Press [2] + [TT] , two beeps sound; TT said the opening hours, in seconds, such as the lock time of 3 seconds, then TT = 03 ;

5 ) Set / modify the generic password to open the door:

  Press [3] + [4 -bit general-purpose open new password ] , two beeps sound, the original 4 -bit universal password is overwritten; press [3] + [000] , two beeps sound, clear all the "common password";

6 ) Set Tamper alarm function:

  ①. tamper alarm off: Press [4] + [0] , two beeps sound;

  ②. open tamper alarm: press [4] + [1] , two beeps sound;

7 ) Set the card:

  Press [5] + [4 -bit card number ] beep sound after two + [ before the induction need to set the controller card ] , gives off a sound, the two beep sound, carboplatin success; ( 4 digits card code is the user custom, which can be 000-500 among any number, each card must not repeat the code, the code is also a "card with a password" access mode of the personal password;

8 ) remove the card:

  ①. according to [6] + [4 digits card code ] , two beeps sound,

  ②. by [7] + [ induction need to remove the card ] , gives off a sound, the beep two beeps; (delete more than one valid card, repeat the above steps)

  ③. Remove all cards have been set, it is recommended to restore the factory settings;

9 ) Set the door sensor alarm status:

  ①. closed door sensor alarm: press [8] + [0] , two beeps sound;

  ②. open door sensor alarm: Press [8] + [1] , two beeps sound; (turn on the feature, when the normally open, no closed, open or not by the controller, the controller will continuously beep beep sounding the alarm, external alarm.)

10 ) to restore the factory settings:

  Press [9] + [86] , two beeps sound, then toot toot sound of three long, 5 seconds toot toot three short beeps, enter the normal working condition;

11 ) to exit programming mode:

  Press [*] , two beeps sound. (For controller settings finished, exit programming mode; If 20 seconds without any programming instruction, the system automatically exit programming mode.)

3 . Force to restore the factory programmed password:

  Remove the controller, the J2 's legs look short after the release, the controller gives off a sound, then two beeps sound, the controller can be programmed to return to the factory password 990,101 .