Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ************************************************************
- * *
- * U-BOOT For Nokia System *
- * *
- ************************************************************
- Boot Version : NUB.2D.12
- Build Date : Jun 13 2018-11:38:29
- U-Boot 2012.07 [Chaos Calmer 15.05.1,unknown] (Jun 13 2018 - 11:38:18)
- smem ram ptable found: ver: 0 len: 5
- NWIFI: reserved 1MB for ramoops. Current size 0x1fb00000
- NWIFI: start of the ramoops partition 0x5fb00000
- DRAM: 491 MiB
- cdp: machine id 0x136c
- cdp: get bootflash type 6!!!!!
- NWIFI: flash_block_size = 65536, or 0x10000
- NWIFI: bootCfgStartAddr = 0x330000, bootCfgSize = 0x10000
- NWIFI: bootCfg1StartAddr = 0x180000, bootCfg1Size = 0x10000
- NAND: SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
- ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000
- 260 MiB
- SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
- PCI0 Link Intialized
- PCI1 Link Intialized
- In: serial
- Out: serial
- Err: serial
- cdp: get part failed for rootfs
- Net: eth0, eth1
- PKRstCnt = 0
- Current Partition is : partA
- SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
- Erasing SPI flash...Writing to SPI flash...done
- After processing : PKRstCnt = 1
- Hit any key to stop autoboot: 2 0
- (IPQ) #
- (IPQ) #
- (IPQ) #
- (IPQ) #
- (IPQ) # tftpboot
- Mac0 unit link down
- Port:1 speed 1000Mbps
- *** Warning: no boot file name; using 'C0A8BCFB.img'
- Using eth1 device
- TFTP from server 192.168.188.253; our IP address is 192.168.188.251
- Filename 'C0A8BCFB.img'.
- Load address: 0x44000000
- Loading: *#################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #########
- done
- Bytes transferred = 8706556 (84d9fc hex)
- (IPQ) # bootm
- ## Booting kernel from FIT Image at 44000000 ...
- Using 'config@1' configuration
- Trying 'kernel@1' kernel subimage
- Description: ARM OpenWrt Linux-5.4.72
- Type: Kernel Image
- Compression: gzip compressed
- Data Start: 0x440000e4
- Data Size: 8674773 Bytes = 8.3 MiB
- Architecture: ARM
- OS: Linux
- Load Address: 0x42208000
- Entry Point: 0x42208000
- Hash algo: crc32
- Hash value: 550ce6a6
- Hash algo: sha1
- Hash value: aa52ed59d9a107688928b5af57ce20bac53f24a7
- Verifying Hash Integrity ... crc32+ sha1+ OK
- ## Flattened Device Tree from FIT Image at 44000000
- Using 'config@1' configuration
- Trying 'fdt@1' FDT blob subimage
- Description: ARM OpenWrt nokia_ac400i device tree blob
- Type: Flat Device Tree
- Compression: uncompressed
- Data Start: 0x44845ff4
- Data Size: 29910 Bytes = 29.2 KiB
- Architecture: ARM
- Hash algo: crc32
- Hash value: 8dc16e11
- Hash algo: sha1
- Hash value: 53c72252c4248dd6f7bcb24b005c1c13f28692f8
- Verifying Hash Integrity ... crc32+ sha1+ OK
- Booting using the fdt blob at 0x44845ff4
- Uncompressing Kernel Image ... OK
- Loading Device Tree to 5eaf5000, end 5eaff4d5 ... OK
- cdp: get part failed for rootfs
- mtdparts = mtdparts=nand0:0x4000000@0(rootfs),0x4000000@0x4000000(rootfs_1),0x8000000@0x8000000(cfg);nand1:128K@0x0(0:SBL1),128K@0x20000(0:MIBIB),192K@0x40000(0:SBL2),64K@0x70000(0:DDRCONFIG_1),192K@0x80000(0:SBL3),192K@0xb0000(0:SBL2_1),128K@0xe0000(0:RPM_1),64K@0x100000(0:DDRCONFIG),64K@0x110000(0:SSD),192K@0x120000(0:TZ),192K@0x150000(0:SBL3_1),64K@0x180000(0:BOOTCONFIG1),64K@0x190000(0:RES1),128K@0x1a0000(0:RPM),192K@0x1c0000(0:TZ_1),192K@0x1f0000(0:RES2),512K@0x220000(0:APPSBL),256K@0x2a0000(0:APPSBLENV),256K@0x2e0000(0:ART),64K@0x320000(0:RES3),64K@0x330000(0:BOOTCONFIG),128K@0x340000(0:RES4),512K@0x360000(0:APPSBL_1),64K@0x3e0000(0:EID-A),64K@0x3f0000(0:EID-B),
- Using machid 0x136c from environment
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 5.4.72 (root@Kyle) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14808-499924adf0)) #0 SMP Tue Nov 3 08:59:59 2020
- [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
- [ 0.000000] CPU: div instructions available: patching division code
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
- [ 0.000000] OF: fdt: Machine model: Nokia AC400i
- [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x42000000
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 120264
- [ 0.000000] Kernel command line: console=ttyHSL1,115200n8 console=ttyMSM0,115200n8 root=/dev/ubiblock0_1
- [ 0.000000] Bootloader command line not present
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 461564K/485376K available (5926K kernel code, 191K rwdata, 1508K rodata, 10240K init, 228K bss, 23812K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
- [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
- [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4e8 with crng_init=0
- [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
- [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
- [ 0.000021] Switching to timer-based delay loop, resolution 160ns
- [ 0.000232] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
- [ 0.000252] pid_max: default: 32768 minimum: 301
- [ 0.000447] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.000467] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.001491] CPU: Testing write buffer coherency: ok
- [ 0.002646] Setting up static identity map for 0x42300000 - 0x42300060
- [ 0.002820] rcu: Hierarchical SRCU implementation.
- [ 0.003317] smp: Bringing up secondary CPUs ...
- [ 0.005237] smp: Brought up 1 node, 2 CPUs
- [ 0.005254] SMP: Total of 2 processors activated (25.00 BogoMIPS).
- [ 0.005264] CPU: All CPU(s) started in SVC mode.
- [ 0.014779] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
- [ 0.014930] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.014960] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
- [ 0.015116] pinctrl core: initialized pinctrl subsystem
- [ 0.016275] NET: Registered protocol family 16
- [ 0.016596] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.017951] cpuidle: using governor ladder
- [ 0.018015] cpuidle: using governor menu
- [ 0.048835] usbcore: registered new interface driver usbfs
- [ 0.048922] usbcore: registered new interface driver hub
- [ 0.049005] usbcore: registered new device driver usb
- [ 0.049062] pps_core: LinuxPPS API ver. 1 registered
- [ 0.049076] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.049108] PTP clock support registered
- [ 0.049876] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
- [ 0.051008] clocksource: Switched to clocksource dg_timer
- [ 0.052071] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.054451] NET: Registered protocol family 2
- [ 0.055023] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
- [ 0.055063] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
- [ 0.055105] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.055159] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.055258] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.055291] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.055536] NET: Registered protocol family 1
- [ 0.055588] PCI: CLS 0 bytes, default 64
- [ 0.249562] workingset: timestamp_bits=14 max_order=17 bucket_order=3
- [ 0.260292] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.260318] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.336460] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
- [ 0.336645] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
- [ 0.336835] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
- [ 0.337254] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
- [ 0.337367] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
- [ 0.337428] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
- [ 0.568462] qcom-pcie 1b500000.pci: Link up
- [ 0.568712] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
- [ 0.568750] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 0.568784] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
- [ 0.568812] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
- [ 0.568904] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
- [ 0.569123] pci 0000:00:00.0: supports D1
- [ 0.569152] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- [ 0.575369] PCI: bus0: Fast back to back transfers disabled
- [ 0.575792] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
- [ 0.576186] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
- [ 0.577412] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
- [ 0.583801] PCI: bus1: Fast back to back transfers disabled
- [ 0.583936] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
- [ 0.583977] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
- [ 0.584124] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.584161] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
- [ 0.585365] pcieport 0000:00:00.0: AER: enabled with IRQ 35
- [ 0.586031] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
- [ 0.586209] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
- [ 0.586384] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
- [ 0.586797] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
- [ 0.586902] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
- [ 0.586957] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
- [ 0.808287] qcom-pcie 1b700000.pci: Link up
- [ 0.808531] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
- [ 0.808564] pci_bus 0001:00: root bus resource [bus 00-ff]
- [ 0.808591] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
- [ 0.808676] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
- [ 0.808867] pci 0001:00:00.0: supports D1
- [ 0.808892] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
- [ 0.815008] PCI: bus0: Fast back to back transfers disabled
- [ 0.815416] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
- [ 0.815801] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
- [ 0.817026] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
- [ 0.823412] PCI: bus1: Fast back to back transfers disabled
- [ 0.823536] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
- [ 0.823576] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
- [ 0.823719] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.823751] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
- [ 0.824900] pcieport 0001:00:00.0: AER: enabled with IRQ 37
- [ 0.828634] L2 @ QSB rate. Forcing new rate.
- [ 0.828945] L2 @ 384000 KHz
- [ 0.829158] CPU0 @ 800000 KHz
- [ 0.829178] CPU1 @ QSB rate. Forcing new rate.
- [ 0.829472] CPU1 @ 384000 KHz
- [ 0.835204] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
- [ 0.836292] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
- [ 0.838377] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.839549] msm_serial 16340000.serial: msm_serial: detected port #0
- [ 0.839636] msm_serial 16340000.serial: uartclk = 7372800
- [ 0.839746] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 38, base_baud = 460800) is a MSM
- [ 0.839802] msm_serial: console setup on port #0
- [ 1.616103] printk: console [ttyMSM0] enabled
- [ 1.621169] msm_serial: driver initialized
- [ 1.633606] loop: module loaded
- [ 1.635805] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
- [ 1.635850] nand: Macronix MX30UF2G18AC
- [ 1.642274] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 1.645815] 3 fixed-partitions partitions found on MTD device qcom_nand.0
- [ 1.653496] Creating 3 MTD partitions on "qcom_nand.0":
- [ 1.660233] 0x000000000000-0x000004000000 : "rootfs"
- [ 1.671145] random: fast init done
- [ 1.783399] mtd: device 0 (rootfs) set to be root filesystem
- [ 1.784098] mtdsplit: no squashfs found in "rootfs"
- [ 1.788174] 0x000004000000-0x000008000000 : "rootfs_1"
- [ 1.910495] 0x000008000000-0x000010000000 : "cfg"
- [ 2.014307] random: crng init done
- [ 2.145900] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
- [ 2.159979] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
- [ 2.160122] 25 qcom-smem partitions found on MTD device spi0.0
- [ 2.164142] Creating 25 MTD partitions on "spi0.0":
- [ 2.169676] 0x000000000000-0x000000020000 : "0:SBL1"
- [ 2.176045] 0x000000020000-0x000000040000 : "0:MIBIB"
- [ 2.181017] 0x000000040000-0x000000070000 : "0:SBL2"
- [ 2.186126] 0x000000070000-0x000000080000 : "0:DDRCONFIG_1"
- [ 2.190995] 0x000000080000-0x0000000b0000 : "0:SBL3"
- [ 2.196366] 0x0000000b0000-0x0000000e0000 : "0:SBL2_1"
- [ 2.201619] 0x0000000e0000-0x000000100000 : "0:RPM_1"
- [ 2.206462] 0x000000100000-0x000000110000 : "0:DDRCONFIG"
- [ 2.211697] 0x000000110000-0x000000120000 : "0:SSD"
- [ 2.216991] 0x000000120000-0x000000150000 : "0:TZ"
- [ 2.221791] 0x000000150000-0x000000180000 : "0:SBL3_1"
- [ 2.226521] 0x000000180000-0x000000190000 : "0:BOOTCONFIG1"
- [ 2.231745] 0x000000190000-0x0000001a0000 : "0:RES1"
- [ 2.237104] 0x0000001a0000-0x0000001c0000 : "0:RPM"
- [ 2.242438] 0x0000001c0000-0x0000001f0000 : "0:TZ_1"
- [ 2.246960] 0x0000001f0000-0x000000220000 : "0:RES2"
- [ 2.252242] 0x000000220000-0x0000002a0000 : "0:APPSBL"
- [ 2.257060] 0x0000002a0000-0x0000002e0000 : "0:APPSBLENV"
- [ 2.262152] 0x0000002e0000-0x000000320000 : "0:ART"
- [ 2.267505] 0x000000320000-0x000000330000 : "0:RES3"
- [ 2.272327] 0x000000330000-0x000000340000 : "0:BOOTCONFIG"
- [ 2.277381] 0x000000340000-0x000000360000 : "0:RES4"
- [ 2.282823] 0x000000360000-0x0000003e0000 : "0:APPSBL_1"
- [ 2.287882] 0x0000003e0000-0x0000003f0000 : "0:EID-A"
- [ 2.293192] 0x0000003f0000-0x000000400000 : "0:EID-B"
- [ 2.300020] libphy: ipq8064_mdio_bus: probed
- [ 2.338670] libphy: Fixed MDIO Bus: probed
- [ 2.339203] ipq806x-gmac-dwmac 37000000.ethernet: IRQ eth_wake_irq not found
- [ 2.341794] ipq806x-gmac-dwmac 37000000.ethernet: IRQ eth_lpi not found
- [ 2.349245] ipq806x-gmac-dwmac 37000000.ethernet: PTP uses main clock
- [ 2.356248] ipq806x-gmac-dwmac 37000000.ethernet: User ID: 0x10, Synopsys ID: 0x37
- [ 2.361942] ipq806x-gmac-dwmac 37000000.ethernet: DWMAC1000
- [ 2.369287] ipq806x-gmac-dwmac 37000000.ethernet: DMA HW capability register supported
- [ 2.375198] ipq806x-gmac-dwmac 37000000.ethernet: RX Checksum Offload Engine supported
- [ 2.382908] ipq806x-gmac-dwmac 37000000.ethernet: COE Type 2
- [ 2.390725] ipq806x-gmac-dwmac 37000000.ethernet: TX Checksum insertion supported
- [ 2.396620] ipq806x-gmac-dwmac 37000000.ethernet: Wake-Up On Lan supported
- [ 2.403997] ipq806x-gmac-dwmac 37000000.ethernet: Enhanced/Alternate descriptors
- [ 2.410692] ipq806x-gmac-dwmac 37000000.ethernet: Enabled extended descriptors
- [ 2.418350] ipq806x-gmac-dwmac 37000000.ethernet: Ring mode enabled
- [ 2.425364] ipq806x-gmac-dwmac 37000000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 2.431531] ipq806x-gmac-dwmac 37000000.ethernet: device MAC address c2:56:f1:fe:66:6b
- [ 2.441592] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
- [ 2.447851] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
- [ 2.455463] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
- [ 2.461968] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
- [ 2.467991] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
- [ 2.475557] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
- [ 2.481344] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
- [ 2.488992] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
- [ 2.496964] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
- [ 2.502775] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
- [ 2.510083] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
- [ 2.516940] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
- [ 2.524486] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
- [ 2.531515] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 2.537613] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 5a:41:8a:de:53:01
- [ 2.547899] i2c /dev entries driver
- [ 2.557652] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
- [ 2.557863] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
- [ 2.565673] sdhci: Secure Digital Host Controller Interface driver
- [ 2.572061] sdhci: Copyright(c) Pierre Ossman
- [ 2.578214] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 2.586255] NET: Registered protocol family 10
- [ 2.590504] Segment Routing with IPv6
- [ 2.592893] NET: Registered protocol family 17
- [ 2.596687] 8021q: 802.1Q VLAN Support v1.8
- [ 2.600808] Registering SWP/SWPB emulation handler
- [ 2.639084] qcom_rpm 108000.rpm: RPM firmware 3.0.16777375
- [ 2.655788] s1a: supplied by regulator-dummy
- [ 2.655967] s1a: Bringing 0uV into 1050000-1050000uV
- [ 2.659606] s1b: supplied by regulator-dummy
- [ 2.664276] s1b: Bringing 0uV into 1050000-1050000uV
- [ 2.668743] s2a: supplied by regulator-dummy
- [ 2.673474] s2a: Bringing 0uV into 775000-775000uV
- [ 2.677964] s2b: supplied by regulator-dummy
- [ 2.682314] s2bV
- [ 2.699584] hct\FF[ 2.711034] Freeing unused kernel memory: 10240K
- [ 2.731691] Run /init as init process
- [ 2.755171] init: Console is alive
- [ 2.755303] init: - watchdog -
- [ 2.773729] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 2.778590] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 2.782566] SCSI subsystem initialized
- [ 2.793404] ehci-fsl: Freescale EHCI Host controller driver
- [ 2.793932] ehci-platform: EHCI generic platform driver
- [ 2.800959] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 2.803456] ohci-platform: OHCI generic platform driver
- [ 2.811105] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
- [ 2.814356] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
- [ 2.820257] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
- [ 2.826428] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
- [ 2.833928] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
- [ 2.837965] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
- [ 2.843759] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
- [ 2.849770] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
- [ 2.857012] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
- [ 2.920243] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
- [ 2.991896] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 2.991947] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
- [ 2.996441] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
- [ 3.003967] xhci-hcd xhci-hcd.0.auto: irq 41, io mem 0x11000000
- [ 3.013795] hub 1-0:1.0: USB hub found
- [ 3.019128] hub 1-0:1.0: 1 port detected
- [ 3.023152] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
- [ 3.027004] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
- [ 3.032387] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
- [ 3.040467] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 3.046836] hub 2-0:1.0: USB hub found
- [ 3.054779] hub 2-0:1.0: 1 port detected
- [ 3.058508] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
- [ 3.062403] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
- [ 3.067760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
- [ 3.075274] xhci-hcd xhci-hcd.1.auto: irq 42, io mem 0x10000000
- [ 3.085643] hub 3-0:1.0: USB hub found
- [ 3.090477] hub 3-0:1.0: 1 port detected
- [ 3.094526] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
- [ 3.098357] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
- [ 3.103728] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
- [ 3.111343] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 3.118103] hub 4-0:1.0: USB hub found
- [ 3.126125] hub 4-0:1.0: 1 port detected
- [ 3.131484] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 3.138391] init: - preinit -
- /bin/board_detect: line 10: Unsupported: not found
- [ 3.413523] ipq806x-gmac-dwmac 37000000.ethernet: Failed to reset the dma
- [ 3.413584] ipq806x-gmac-dwmac 37000000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
- [ 3.419320] ipq806x-gmac-dwmac 37000000.ethernet eth0: stmmac_open: Hw setup failed
- ip: SIOCSIFFLAGS: Resource busy
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- sendto(): Network unreachable
- sendto(): Network unreachable
- [ 6.547804] procd: - early -
- [ 6.547880] procd: - watchdog -
- [ 7.096569] procd: - watchdog -
- [ 7.097207] procd: - ubus -
- [ 7.152694] procd: - init -
- Please press Enter to activate this console.
- [ 7.318804] urngd: v1.0.2 started.
- [ 7.344623] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 7.349658] Loading modules backported from Linux version v5.8-0-gbcf876870b95
- [ 7.350036] Backport generated by backports.git v5.8-1-0-g79400d9e
- [ 7.362608] xt_time: kernel timezone is -0000
- [ 7.387145] PPP generic driver version 2.4.2
- [ 7.387567] NET: Registered protocol family 24
- [ 7.403799] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x46.
- [ 7.403856] ath10k_mac_create, priv_size: 868 hw: 47dc9e49 hw->priv: 8228e0ab
- [ 7.410584] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
- [ 7.418195] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
- [ 8.154849] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
- [ 8.154890] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
- [ 8.166556] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
- [ 10.484742] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
- [ 16.337921] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
- [ 16.339118] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
- [ 16.343443] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
- [ 16.426365] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
- [ 16.427206] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
- [ 16.715270] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
- [ 16.818822] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x46.
- [ 16hw->priv: 413b8d0c
- [ 16.826173] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
- [ 16.833244] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
- [ 17.598016] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
- [ 17.598055] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
- [ 17.609857] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
- [ 19.937603] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
- [ 25.780006] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
- [ 25.780833] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
- [ 25.785499] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
- [ 25.869089] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
- [ 25.869948] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
- [ 26.170595] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
- [ 26.277566] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 32.162013] ipq806x-gmac-dwmac 37000000.ethernet: Failed to reset the dma
- [ 32.162080] ipq806x-gmac-dwmac 37000000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
- [ 32.167815] ipq806x-gmac-dwmac 37000000.ethernet eth0: stmmac_open: Hw setup failed
- [ 32.179083] br-lan: port 1(eth0) entered blocking state
- [ 32.184805] br-lan: port 1(eth0) entered disabled state
- [ 32.190147] device eth0 entered promiscuous mode
- [ 32.203209] dwmac1000: Master AXI performs any burst length
- [ 32.203241] ipq806x-gmac-dwmac 37200000.ethernet eth1: No Safety Features support found
- [ 32.207590] ipq806x-gmac-dwmac 37200000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
- [ 32.215758] ipq806x-gmac-dwmac 37200000.ethernet eth1: registered PTP clock
- [ 32.224762] ipq806x-gmac-dwmac 37200000.ethernet eth1: configuring for fixed/rgmii link mode
- [ 32.231867] ipq806x-gmac-dwmac 37200000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
- [ 32.252982] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- BusyBox v1.31.1 () built-in shell (ash)
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- OpenWrt SNAPSHOT, r14808+1-499924adf0
- -----------------------------------------------------
- === WARNING! =====================================
- There is no root password defined on this device!
- Use the "passwd" command to set up a new password
- in order to prevent unauthorized SSH logins.
- --------------------------------------------------
- root@OpenWrt:/# ip a
- 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
- link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
- inet 127.0.0.1/8 scope host lo
- valid_lft forever preferred_lft forever
- inet6 ::1/128 scope host
- valid_lft forever preferred_lft forever
- 2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop master br-lan state DOWN qlen 1000
- link/ether c2:56:f1:fe:66:6b brd ff:ff:ff:ff:ff:ff
- 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
- link/ether 5a:41:8a:de:53:01 brd ff:ff:ff:ff:ff:ff
- inet6 fe80::5841:8aff:fede:5301/64 scope link
- valid_lft forever preferred_lft forever
- 4: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
- link/ether 00:03:7f:ba:db:02 brd ff:ff:ff:ff:ff:ff
- 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
- link/ether 00:03:7f:ba:db:03 brd ff:ff:ff:ff:ff:ff
- 6: br-lan: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN qlen 1000
- link/ether c2:56:f1:fe:66:6b brd ff:ff:ff:ff:ff:ff
- inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
- valid_lft forever preferred_lft forever
- inet6 fd98:696a:ea01::1/60 scope global tentative
- valid_lft forever preferred_lft forever
- root@OpenWrt:/#
- root@OpenWrt:/# cat /sys/kernel/debug/gpio
- gpiochip0: GPIOs 443-511, parent: platform/800000.pinmux, 800000.pinmux:
- gpio0 : in high func1 8mA no pull
- gpio1 : out high func1 8mA no pull
- gpio2 : out high func0 2mA pull up
- gpio3 : out high func0 12mA pull up
- gpio4 : in high func0 2mA pull down
- gpio5 : in low func0 2mA pull down
- gpio6 : in low func0 2mA pull down
- gpio7 : in low func0 2mA pull down
- gpio8 : out low func0 16mA pull down
- gpio9 : out low func0 16mA pull down
- gpio10 : out low func1 12mA no pull
- gpio11 : out low func1 12mA no pull
- gpio12 : in low func0 2mA no pull
- gpio13 : in low func0 2mA no pull
- gpio14 : in high func0 2mA pull down
- gpio15 : in high func0 2mA pull up
- gpio16 : in high func0 2mA pull down
- gpio17 : in low func0 2mA pull down
- gpio18 : in low func1 10mA pull down
- gpio19 : in low func1 10mA pull down
- gpio20 : out high func0 10mA pull up
- gpio21 : in low func1 12mA pull down
- gpio22 : out high func0 2mA pull up
- gpio23 : out high func0 2mA pull up
- gpio24 : in high func0 2mA pull down
- gpio25 : in high func0 2mA pull down
- gpio26 : out high func0 2mA pull up
- gpio27 : out low func2 8mA no pull
- gpio28 : out low func2 8mA no pull
- gpio29 : out low func2 8mA no pull
- gpio30 : out low func2 8mA no pull
- gpio31 : out low func2 8mA no pull
- gpio32 : out low func2 8mA no pull
- gpio33 : out low func0 2mA no pull
- gpio34 : out low func1 10mA no pull
- gpio35 : out low func1 10mA no pull
- gpio36 : out low func1 10mA no pull
- gpio37 : out low func1 10mA no pull
- gpio38 : out low func1 10mA no pull
- gpio39 : out low func1 10mA pull up
- gpio40 : out low func1 10mA keeper
- gpio41 : out low func1 10mA keeper
- gpio42 : out low func1 10mA keeper
- gpio43 : out low func1 10mA keeper
- gpio44 : out low func1 10mA keeper
- gpio45 : out low func1 10mA keeper
- gpio46 : out low func1 10mA keeper
- gpio47 : out low func1 10mA keeper
- gpio48 : out high func0 12mA pull up
- gpio49 : in high func0 2mA pull down
- gpio50 : in low func0 2mA pull down
- gpio51 : in high func2 8mA no pull
- gpio52 : in high func2 8mA no pull
- gpio53 : out low func0 2mA pull up
- gpio54 : out low func0 2mA pull up
- gpio55 : out low func0 2mA pull up
- gpio56 : out low func0 2mA pull up
- gpio57 : in low func0 2mA pull down
- gpio58 : in high func0 2mA pull down
- gpio59 : in high func2 8mA no pull
- gpio60 : in low func2 8mA no pull
- gpio61 : in high func2 8mA no pull
- gpio62 : in low func2 8mA no pull
- gpio63 : in low func0 2mA pull down
- gpio64 : out low func0 2mA pull up
- gpio65 : out low func0 2mA pull up
- gpio66 : in low func0 2mA pull down
- gpio67 : out low func0 2mA pull up
- gpio68 : out low func0 2mA pull up
- root@OpenWrt:/#
- root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement