SHARE
TWEET

Untitled

a guest May 19th, 2019 72 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. UART_115200
  2. LP_snPD
  3. Hello U-Boot
  4. [LGPS]: u16LongPulseThr = 07D0
  5. [INTG]: u16IntegrationThr = 0052
  6. [WDOG]: u8WatchDogCount = 0024
  7.  
  8.  
  9. U-Boot 1.1.6 (Oct 13 2011 - 21:23:42)
  10.  
  11. Board: MSTAR TITANIA4 (CPU Speed 312 MHz)
  12. DRAM:  128 MBytes
  13. U-Boot is running at DRAM 0x87600000
  14. Module: USB FAT NAND UBI UBIFS SPI JFFS2
  15. MBOOT UNFD T4-----------------------------------------------------------20110728 21:23:41
  16. NAND ID 20 76
  17. nand_unfd_init ECC_TYPE_4BIT
  18. >>>pagesize = 512
  19. NAND: 64 MBytes
  20. In:    serial
  21. Out:   serial
  22. Err:   serial
  23. Skipping flash_init
  24. MSVC00B000100100208768TH0000000T
  25. 1Ghz
  26.  keypad_pressed is [0]
  27. Flash is detected (0x0707, 0xEF, 0x40, 0x14)
  28. no OAD Flag
  29. no need start factory usb download
  30. no need start factory usb download
  31.  
  32.  #* NAND is already programmed (not Empty) ***
  33. Wait for PM51 standby...........
  34. PM51 run ok...........
  35. Hit any key to stop autoboot:  0
  36.  
  37. NAND read: device 0 offset 0x0, size 0x320000
  38.  
  39. Reading data from 0x0 -- 100% complete.
  40.  3276800 bytes read: OK, time=00000000
  41. ## Booting image at 81000000 ...
  42.    Image Name:   Linux-2.6.28.10-mstar
  43.    Created:      2012-01-05   3:19:36 UTC
  44.    Image Type:   MIPS Linux Kernel Image (uncompressed)
  45.    Data Size:    3017080 Bytes =  2.9 MB
  46.    Load Address: 80200000
  47.    Entry Point:  80204150
  48. OK
  49.  
  50. Starting kernel ...
  51.  
  52. L2 enabled
  53. Linux version 2.6.28.10 (root@localhost.localdomain) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #32 PREEMPT Thu Jan 5 11:19:23 CST 2012
  54.  
  55. LINUX started...
  56. boot_command_line: console=ttyS0,115200 ubi.mtd=1 ubi.mtd=2,512 root=ubi1:RFS rootfstype=ubifs rw LX_MEM=0x3400000 EMAC_MEM=0 DRAM_LEN=0x8000000 mtdparts=edb64M-nand:3200k(KL),11392k(CONF),22m(UBIA),25m(UBIB),-(NA) MBOOT_VER=1.1.6-161M62 SPI
  57.  
  58. LX_MEM  = 0x200000, 0x27C0000
  59. LX_MEM2 = 0x0, 0x0
  60. CPHYSADDR(PFN_ALIGN(&_end))= 0x51B000
  61. EMAC_LEN= 0x0
  62. DRAM_LEN= 0x8000000
  63. console [early0] enabled
  64. CPU revision is: 00019555 (MIPS 34Kc)
  65. Begin Mstar_Chip_setup
  66. Determined physical RAM map:
  67.  memory: 027c0000 @ 00200000 (usable)
  68. Wasting 16384 bytes for tracking 512 unused pages
  69. Zone PFN ranges:
  70.   DMA      0x00000200 -> 0x000029c0
  71.   Normal   0x000029c0 -> 0x000029c0
  72.   HighMem  0x000029c0 -> 0x000029c0
  73. Movable zone start PFN for each node
  74. early_node_map[1] active PFN ranges
  75.     0: 0x00000200 -> 0x000029c0
  76. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 10096
  77. Kernel command line: console=ttyS0,115200 ubi.mtd=1 ubi.mtd=2,512 root=ubi1:RFS rootfstype=ubifs rw LX_MEM=0x3400000 EMAC_MEM=0 DRAM_LEN=0x8000000 mtdparts=edb64M-nand:3200k(KL),11392k(CONF),22m(UBIA),25m(UBIB),-(NA) MBOOT_VER=1.1.6-161M62 SPI
  78. alloc ebase: 81059000
  79. Primary instruction cache 8kB, VIPT, 4-way, linesize 32 bytes.
  80. Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 32 bytes
  81. Writing ErrCtl register=00037a0e
  82. Readback ErrCtl register=00037a0e
  83. PID hash table entries: 256 (order: 8, 1024 bytes)
  84. CPU freq count = 156000000
  85. CPU frequency 312.00 MHz
  86. console handover: boot [early0] -> real [ttyS0]
  87. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  88. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  89. Memory: 37068k/40704k available (2214k kernel code, 3616k reserved, 608k data, 124k init, 0k highmem)
  90. SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  91. Calibrating delay loop... 205.31 BogoMIPS (lpj=102656)
  92. Mount-cache hash table entries: 512
  93. net_namespace: 288 bytes
  94. NET: Registered protocol family 16
  95. SCSI subsystem initialized
  96. usbcore: registered new interface driver usbfs
  97. usbcore: registered new interface driver hub
  98. usbcore: registered new device driver usb
  99. NET: Registered protocol family 1
  100. msgmni has been set to 72
  101. io scheduler noop registered
  102. io scheduler anticipatory registered
  103. io scheduler deadline registered
  104. io scheduler cfq registered (default)
  105. Serial: 8250/16550 driver4 ports, IRQ sharing disabled
  106. serial8250: ttyS0 at I/O 0xbf201300 (irq = 8) is a 16550
  107. brd: module loaded
  108. loop: module loaded
  109. Driver 'sd' needs updating - please use bus_type methods
  110. Driver 'sr' needs updating - please use bus_type methods
  111. usbmon: debugfs is not available
  112. NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bit)
  113. Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":
  114. 0x00000000-0x00320000 : "KL"
  115. mtd: Giving out device 0 to KL
  116. 0x00320000-0x00e40000 : "CONF"
  117. mtd: Giving out device 1 to CONF
  118. 0x00e40000-0x02440000 : "UBIA"
  119. mtd: Giving out device 2 to UBIA
  120. 0x02440000-0x03d40000 : "UBIB"
  121. mtd: Giving out device 3 to UBIB
  122. 0x03d40000-0x04000000 : "NA"
  123. mtd: Giving out device 4 to NA
  124. parse_cmdline_partitions: add_mtd_partitions
  125. NET: Registered protocol family 17
  126. VFS: Mounted root (ubifs filesystem).
  127. init started: BusyBox v1.14.1 (2010-06-23 18:41:22 CST)
  128. starting pid 179, tty '': '/etc/init.d/rcS'
  129. Mounting conf
  130. Mounting vendor
  131. ******Application Started*****
  132. pthread_mutex_init
  133. CHIP_InitISR
  134. mem_type: 0, phy_addr = 0x75c1000, start_addr = 0x42082000, size = 6291456
  135. mem_type: 1, phy_addr = 0x7bc1000, start_addr = 0x32682000, size = 0
  136. ******* ICE_LoadProfileData - Enter
  137. Load profile /conf/mb62_hwprofile.bin
  138. ******* ICE_LoadProfileData - Exit
  139. ******* ICE_LoadProfileData - Enter
  140. Load profile /conf/mb62_swprofile.bin
  141. ******* ICE_LoadProfileData - Exit
  142. ******* ICE_LoadProfileData - Enter
  143. PM Bank mapping success. Base=[4b306000], Size=[225600]
  144. NonPM Bank mapping success. Base=[4b52c000], Size=[25600]
  145. Flash Bank0 mapping success. Base=[4b552000], Size=[4000000]
  146. **** ICE_HardwareInit ****
  147. FROST_DebugStartConsole !
  148. Terminal: vt102
  149. terminal ready
  150. Load profile /conf/mb62_langprofile.bin
  151.  
  152. #*### Console Started ###
  153. Load tune file
  154.  
  155. Try loading bin panel file
  156. Read : 15084 target: 15084
  157.  
  158. TUNER : SONY      EXTENSION :
  159. Load country file
  160. ---> DDFSPAN = 0x29a (666)
  161. Flash is detected (0x0707, 0xEF, 0x40, 0x14)
  162. --------->MBX DRIVER OPEN
  163. _MDrv_MBXIO_FASYNC is invoked
  164.  
  165. ICE_LowPowerModeForceStandby(): exit_type[0] - fti[0] - pin8_en[1] - hotel[2] - profile[1] - last_state_standby[1] -child_lock[0]
  166. disable DVD wakeup
  167. Get PM command: 0x30.
  168. MDrv_PM_Init OK
  169. Fast Standby: MDrv_PM_PowerDown ...
  170. UART_115200
  171. LP_snPD
  172. Hello U-Boot
  173. [LGPS]: u16LongPulseThr = 07D0
  174. [INTG]: u16IntegrationThr = 0052
  175. [WDOG]: u8WatchDogCount = 0024
  176.  
  177.  
  178. U-Boot 1.1.6 (Oct 13 2011 - 21:23:42)
  179.  
  180. Board: MSTAR TITANIA4 (CPU Speed 312 MHz)
  181. DRAM:  128 MBytes
  182. U-Boot is running at DRAM 0x87600000
  183. Module: USB FAT NAND UBI UBIFS SPI JFFS2
  184. MBOOT UNFD T4-----------------------------------------------------------20110728 21:23:41
  185. NAND ID 20 76
  186. nand_unfd_init ECC_TYPE_4BIT
  187. >>>pagesize = 512
  188. NAND: 64 MBytes
  189. In:    serial
  190. Out:   serial
  191. Err:   serial
  192. Skipping flash_init
  193. MSVC00B000100100208768TH0000000T
  194. 1Ghz
  195.  keypad_pressed is [0]
  196. Flash is detected (0x0707, 0xEF, 0x40, 0x14)
  197. no OAD Flag
  198. no need start factory usb download
  199. no need start factory usb download
  200.  
  201.  #* NAND is already programmed (not Empty) ***
  202. Wait for PM51 standby...........
  203. PM51 run ok...........
  204. Hit any key to stop autoboot:  0
  205.  
  206. NAND read: device 0 offset 0x0, size 0x320000
  207.  
  208. Reading data from 0x0 -- 100% complete.
  209.  3276800 bytes read: OK, time=00000000
  210. ## Booting image at 81000000 ...
  211.    Image Name:   Linux-2.6.28.10-mstar
  212.    Created:      2012-01-05   3:19:36 UTC
  213.    Image Type:   MIPS Linux Kernel Image (uncompressed)
  214.    Data Size:    3017080 Bytes =  2.9 MB
  215.    Load Address: 80200000
  216.    Entry Point:  80204150
  217. OK
  218.  
  219. Starting kernel ...
  220.  
  221. L2 enabled
  222. Linux version 2.6.28.10 (root@localhost.localdomain) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #32 PREEMPT Thu Jan 5 11:19:23 CST 2012
  223.  
  224. LINUX started...
  225. boot_command_line: console=ttyS0,115200 ubi.mtd=1 ubi.mtd=2,512 root=ubi1:RFS rootfstype=ubifs rw LX_MEM=0x3400000 EMAC_MEM=0 DRAM_LEN=0x8000000 mtdparts=edb64M-nand:3200k(KL),11392k(CONF),22m(UBIA),25m(UBIB),-(NA) MBOOT_VER=1.1.6-161M62 SPI
  226.  
  227. LX_MEM  = 0x200000, 0x27C0000
  228. LX_MEM2 = 0x0, 0x0
  229. CPHYSADDR(PFN_ALIGN(&_end))= 0x51B000
  230. EMAC_LEN= 0x0
  231. DRAM_LEN= 0x8000000
  232. console [early0] enabled
  233. CPU revision is: 00019555 (MIPS 34Kc)
  234. Begin Mstar_Chip_setup
  235. Determined physical RAM map:
  236.  memory: 027c0000 @ 00200000 (usable)
  237. Wasting 16384 bytes for tracking 512 unused pages
  238. Zone PFN ranges:
  239.   DMA      0x00000200 -> 0x000029c0
  240.   Normal   0x000029c0 -> 0x000029c0
  241.   HighMem  0x000029c0 -> 0x000029c0
  242. Movable zone start PFN for each node
  243. early_node_map[1] active PFN ranges
  244.     0: 0x00000200 -> 0x000029c0
  245. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 10096
  246. Kernel command line: console=ttyS0,115200 ubi.mtd=1 ubi.mtd=2,512 root=ubi1:RFS rootfstype=ubifs rw LX_MEM=0x3400000 EMAC_MEM=0 DRAM_LEN=0x8000000 mtdparts=edb64M-nand:3200k(KL),11392k(CONF),22m(UBIA),25m(UBIB),-(NA) MBOOT_VER=1.1.6-161M62 SPI
  247. alloc ebase: 81059000
  248. Primary instruction cache 8kB, VIPT, 4-way, linesize 32 bytes.
  249. Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 32 bytes
  250. Writing ErrCtl register=0003a007
  251. Readback ErrCtl register=0003a007
  252. PID hash table entries: 256 (order: 8, 1024 bytes)
  253. CPU freq count = 156000000
  254. CPU frequency 312.00 MHz
  255. console handover: boot [early0] -> real [ttyS0]
  256. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  257. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  258. Memory: 37068k/40704k available (2214k kernel code, 3616k reserved, 608k data, 124k init, 0k highmem)
  259. SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  260. Calibrating delay loop... 205.31 BogoMIPS (lpj=102656)
  261. Mount-cache hash table entries: 512
  262. net_namespace: 288 bytes
  263. NET: Registered protocol family 16
  264. SCSI subsystem initialized
  265. usbcore: registered new interface driver usbfs
  266. usbcore: registered new interface driver hub
  267. usbcore: registered new device driver usb
  268. NET: Registered protocol family 1
  269. msgmni has been set to 72
  270. io scheduler noop registered
  271. io scheduler anticipatory registered
  272. io scheduler deadline registered
  273. io scheduler cfq registered (default)
  274. Serial: 8250/16550 driver4 ports, IRQ sharing disabled
  275. serial8250: ttyS0 at I/O 0xbf201300 (irq = 8) is a 16550
  276. brd: module loaded
  277. loop: module loaded
  278. Driver 'sd' needs updating - please use bus_type methods
  279. Driver 'sr' needs updating - please use bus_type methods
  280. usbmon: debugfs is not available
  281. NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bit)
  282. Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":
  283. 0x00000000-0x00320000 : "KL"
  284. mtd: Giving out device 0 to KL
  285. 0x00320000-0x00e40000 : "CONF"
  286. mtd: Giving out device 1 to CONF
  287. 0x00e40000-0x02440000 : "UBIA"
  288. mtd: Giving out device 2 to UBIA
  289. 0x02440000-0x03d40000 : "UBIB"
  290. mtd: Giving out device 3 to UBIB
  291. 0x03d40000-0x04000000 : "NA"
  292. mtd: Giving out device 4 to NA
  293. parse_cmdline_partitions: add_mtd_partitions
  294. NET: Registered protocol family 17
  295. VFS: Mounted root (ubifs filesystem).
  296. init started: BusyBox v1.14.1 (2010-06-23 18:41:22 CST)
  297. starting pid 179, tty '': '/etc/init.d/rcS'
  298. Mounting conf
  299. Mounting vendor
  300. ******Application Started*****
  301. pthread_mutex_init
  302. CHIP_InitISR
  303. mem_type: 0, phy_addr = 0x75c1000, start_addr = 0x42082000, size = 6291456
  304. mem_type: 1, phy_addr = 0x7bc1000, start_addr = 0x32682000, size = 0
  305. ******* ICE_LoadProfileData - Enter
  306. Load profile /conf/mb62_hwprofile.bin
  307. ******* ICE_LoadProfileData - Exit
  308. ******* ICE_LoadProfileData - Enter
  309. Load profile /conf/mb62_swprofile.bin
  310. ******* ICE_LoadProfileData - Exit
  311. ******* ICE_LoadProfileData - Enter
  312. PM Bank mapping success. Base=[4b306000], Size=[225600]
  313. NonPM Bank mapping success. Base=[4b52c000], Size=[25600]
  314. Flash Bank0 mapping success. Base=[4b552000], Size=[4000000]
  315. **** ICE_HardwareInit ****
  316. FROST_DebugStartConsole !
  317. Terminal: vt102
  318. terminal ready
  319. Load profile /conf/mb62_langprofile.bin
  320.  
  321. #*### Console Started ###
  322. Load tune file
  323.  
  324. Try loading bin panel file
  325. Read : 15084 target: 15084
  326.  
  327. TUNER : SONY      EXTENSION :
  328. Load country file
  329. ---> DDFSPAN = 0x29a (666)
  330. Flash is detected (0x0707, 0xEF, 0x40, 0x14)
  331. --------->MBX DRIVER OPEN
  332. _MDrv_MBXIO_FASYNC is invoked
  333.  
  334. ICE_LowPowerModeForceStandby(): exit_type[5] - fti[0] - pin8_en[1] - hotel[2] - profile[1] - last_state_standby[1] -child_lock[0]
  335. _MApi_XC_Sys_Init_Panel
  336. XC: [_MApi_XC_Init_Context][167] This is first initial 0x2aab8810
  337. Sub window input source must be disabled before set frame buffer address. Ex:when video play, you can��t use this function.
  338. IRQThread_18
  339. TextBinStartaDDR ID0=14a1f48
  340. BinStartaDDR ID0=506b1008
  341. BinStartaDDR ID2=14a6f50
  342. [MWE] Hstart   70  Hend   6f  Vstart    0 Vend  437
  343. Found new edid file in file system
  344. e3a = 0 & 1
  345. e3c = 0 & 1
  346. e38 = 0 & 10
  347. e3a = 0 & 4
  348. e3c = 4 & 4
  349. e38 = 40 & 40
  350. e20 = 10 & bf
  351. e21 = 1 & 1b
  352. e1e = 40 & bf
  353. e1f = 0 & 1b
  354. e6a = 4 & 4
  355. e4e = 30 & 70
  356. e4e = 0 & 7
  357. 496 = 0 & 44
  358. 496 = 0 & 22
  359. 496 = 0 & 80
  360. 497 = 0 & 44
  361. 497 = 0 & 22
  362. 497 = 0 & 80
  363. 498 = 0 & 44
  364. 498 = 0 & 22
  365. 498 = 0 & 80
  366. 1424 = 0 & f
  367. 1423 = d & f
  368. 1422 = d & f
  369. 1e56 = 0 & ff
  370. 1e57 = 0 & ff
  371. 1e58 = 0 & ff
  372. 1e59 = 0 & f
  373. 1e5c = 0 & ff
  374. 1e5d = 0 & ff
  375. 1e5e = 0 & ff
  376. 1e5f = 0 & f
  377. 1e85 = 10 & f0
  378. 1e87 = 20 & f0
  379. 1e39 = c & f
  380. 1ec8 = 80 & 80
  381. 1e85 = 6 & 6
  382. 1e87 = 0 & 6
  383. 1e8b = 3 & f
  384. 1e8c = 0 & 0
  385. 1e8d = 0 & f
  386. 1e8e = 0 & 0
  387. 1e64 = 0 & ff
  388. 1e65 = 0 & 7
  389. 1e68 = 0 & ff
  390. 1e69 = 0 & 7
  391. 1e4c = 0 & ff
  392. 1e4d = 0 & 7
  393. 1e4e = 0 & ff
  394. 1e4f = 0 & 7
  395. 1e76 = 0 & ff
  396. 1e77 = 0 & ff
  397. 1e78 = 0 & ff
  398. 1e79 = 0 & ff
  399. 1e7c = 0 & ff
  400. 1e7d = 0 & ff
  401. 1e7e = 0 & ff
  402. 1e7f = 0 & ff
  403. 1e7a = 0 & 1
  404. 1e80 = 1 & 1
  405. 1ee0 = 1 & 1
  406. 1e7b = 0 & 1f
  407. 1e81 = d & 1f
  408. 1e8a = 0 & 7f
  409. 1e8b = 0 & 7c
  410. 1ec8 = 0 & 40
  411. 1e98 = 41 & ff
  412. 1e99 = 0 & ff
  413. 1e9a = 0 & 3f
  414. 1e9c = 10 & ff
  415. 1e9d = 0 & ff
  416. 1e9b = 0 & 3f
  417. 1e6c = 2 & ff
  418. 1e6d = 0 & f
  419. 1e6e = 44 & ff
  420. 1e6f = 0 & f
  421. 1ea0 = 0 & 40
  422. 1eaf = 1 & 3
  423. 1eaf = 18 & 38
  424. 1e05 = 0 & c0
  425. 1ede = 0 & 10
  426. 1eae = 0 & 1c
  427. 1eae = c0 & e0
  428. 1eae = 0 & 3
  429. 1ec9 = 0 & e
  430. e13 = 8 & 8
  431. e13 = 0 & 10
  432. 3c1d = df & e0
  433. 1ea1 = 0 & 80
  434. @@@@@@ u32CpuSpeedMHz= 312 MHz
  435. @@@@@@ u32AdjParam= 35 MHz
  436.  
  437. -------------- Calibration failed.
  438. IRQThread_69
  439. DSP code loaded successfully
  440. IRQThread_54
  441. ******************start TSP init*********************************
  442. [HAL_TSP_CPU_SetBase][1720] load firmware (address, size) = (0x004aa000, 0x00004400)
  443. firmware 111 0x004aa000 0x00010000 0x00002a80
  444. IRQThread_24
  445. **********************End TSP init*****************************
  446. Init GFX...
  447. GFX lib version: GFX_170000252256
  448. PoolAlloc(mtype, addr, size, used_size) = (0, 0x424a1ff0,1966080,1966080 )
  449. Init OSD Plane... H: 1080, W: 1920, HStr: 112
  450. GOP Addr: 05204000, 00384000, 05588000, 00002000
  451. [GFlip (Driver)][00289] [MDrv_GFLIP_Init][289] open fail /dev/gflip
  452. [GFlip (Driver)][00289] [MDrv_GFLIP_Init][289] open fail /dev/gflip
  453.  
  454. ====================
  455. First GOP driver instance, flush GWIN HW
  456. ====================
  457.  
  458. GOP lib version: GOP_660000296153
  459. ==> GOP protect: start_adr=0x5204000, end_adr=0x5587fff
  460. ==> PM51 protect: start_adr=0x55b0000, end_adr=0x55bffff
  461. End GOP init
  462. IRQThread_36
  463. _ICE_TuneLoadDSP
  464. DVD Player: _mapi_PadThread: EMC Modifications are DISABLED
  465. ------------------> mdev_CofdmDisableTSPAD
  466. CheckForTheFirstTime file open error
  467. Profile_GetUartBaundrateOption : 11
  468. ***** ICE_HardwareInit end *****
  469. HW_getMbootVersion ret 1
  470. =================================================================
  471. ## Software Version: V.0.6.8 SVN 69945
  472.    MBoot Version:    1.1.6-161M62 SPI
  473.    Panel:           215LG_TLG1__169FHD__E_N_NO_T_NO_ER_75720_62_ -  - V1.83 - xxxxxxxxx
  474.    Pq:              PQTool_MB62_TOS_FHD_49456
  475.    Profile:         62_2TT30074858SNFR_64_1S622__K100010C023EV068a1
  476.    Touchpad Version:    V0
  477.    Tuner Version:     SONY      Extension :
  478.    Pix Files:       IC IS NOT AVAILABLE
  479.    HW Profile Version: SUT RE216 driver 0.4
  480.  072   SW Profile Version:  111   Lan Profile Version: Not Defined
  481.    Country : Poland
  482.  
  483. =================================================================
  484. DVB-T Load DSP Code OK
  485. [DVBT]Version = 0xe00f.14
  486. _ICE_TuneLoadDSP Ends
  487. [DVBT]Version = 0xe00f.14
  488.  
  489. set Freq SUT Tuner DTV Freq 666000KHz
  490. mode -> DVBT 6M
  491. region -> other
  492. ******* ICE_LoadProfileData - Exit
  493. PCMCIA open /dev/system success >> SYS_fd= 6
  494. IRQThread_29
  495. [HAL_DSCMB_SetBank][82] Set bank 0x4b52c000
  496. [CI] By-Pass(P-EMBEDDED) Mode ================
  497. PoolAlloc(mtype, addr, size, used_size) = (0, 0x423a4de0,1036800,3002880 )
  498. **********InitAESKey*********
  499. intput streaming_path      : 0,a:/DVR/RECS
  500. default_drive_number       : 0
  501. default_partition          : a
  502. default_descriptor_string  : /DVR/RECS/
  503. default_partial_path       : /mnt/hd0a/DVR/RECS/
  504. PoolAlloc(mtype, addr, size, used_size) = (0, 0x422da5d0,829440,3832320 )
  505. ... init, 1167
  506. Is PVR Supported:[0]
  507. [LGPS]: u16LongPulseThr = 07D0
  508. [INTG]: u16IntegrationThr = 0052
  509. [WDOG]: u8WatchDogCount = 0024
  510. IRQThread_104
  511. ... init, 1208
  512. ... init, 1277
  513. audio DSP_SE LoadCode success..
  514. audio DSP_DEC LoadCode success..
  515.  
  516. ==HAL_AUDIO_SPDIF_SetMode, u8Spdif_mode = 0 , u8Input_src = 3==
  517.  
  518. ==PCM mode==
  519. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  520. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  521. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  522. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  523. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  524. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  525. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  526. msAPI_AUD_SetPEQ PEQ paramater Foh should be 1~160
  527. ****** deferred initcalls set to 1
  528. Running do_deferred_initcalls()
  529. Mstar-ehci-2 H.W init
  530. Titania3_later_start_ehc2 start
  531. Mstar-ehci-2 Mstar-ehci-2.1: Mstar EHCI
  532. Mstar-ehci-2 Mstar-ehci-2.1: new USB bus registered, assigned bus number 1
  533. Mstar-ehci-2 Mstar-ehci-2.1: irq 74, io mem 0xbf201a00
  534. usb usb1: configuration #1 chosen from 1 choice
  535. hub 1-0:1.0: USB hub found
  536. hub 1-0:1.0: 1 port detected
  537. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  538. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  539. usb usb1: Product: Mstar EHCI
  540. usb usb1: Manufacturer: Linux 2.6.28.10 ehci_hcd
  541. usb usb1: SerialNumber: mstar
  542. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  543. Mstar-ehci-1 H.W init
  544. Titania3_later_start_ehc1 start
  545. Mstar-ehci-1 Mstar-ehci-1.0: Mstar EHCI
  546. Mstar-ehci-1 Mstar-ehci-1.0: new USB bus registered, assigned bus number 2
  547. Mstar-ehci-1 Mstar-ehci-1.0: irq 15, io mem 0xbf204800
  548. usb usb2: configuration #1 chosen from 1 choice
  549. hub 2-0:1.0: USB hub found
  550. hub 2-0:1.0: 1 port detected
  551. usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  552. usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  553. usb usb2: Product: Mstar EHCI
  554. usb usb2: Manufacturer: Linux 2.6.28.10 ehci_hcd
  555. usb usb2: SerialNumber: mstar
  556. Freeing unused kernel memory: 124k freed
  557. 0
  558. /lib/modules/usb-storage.ko insmodding now
  559. Initializing USB Mass Storage driver...
  560. usbcore: registered new interface driver usb-storage
  561. USB Mass Storage support registered.
  562. ====> image: 22058576 ,len: 83687 , options : , rc : 0
  563. FINAL_MODULE insmodding now
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top