U-Boot 2016.03-20256-g39f64de-dirty (Apr 27 2016 - 16:56:56 +0200)

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: SABRE Lite
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Display: lvds:chimei-g104x1-l03-rgb24 (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   Micrel ksz9021 at 6
FEC [PRIME]
Error: FEC address not set.
, usb_ether
Hit any key to stop autoboot:  0
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part
No port device detected!
** Bad device size - sata 0 **

SATA device 1: unknown device
** Bad device sata 1 **
MMC: no card present
MMC: no card present
** Bad device mmc 0 **
switch to partitions #0, OK
mmc1 is current device
4070 bytes read in 31 ms (127.9 KiB/s)
## Executing script at 10008000
0 bytes read in 155 ms (0 Bytes/s)
42732 bytes read in 889 ms (46.9 KiB/s)
only CEA modes allowed on HDMI port
----------- trying to load /initrd.img
2405634 bytes read in 377 ms (6.1 MiB/s)
5374368 bytes read in 640 ms (8 MiB/s)
Kernel image @ 0x10800000 [ 0x000000 - 0x5201a0 ]
## Flattened Device Tree blob at 13000000
   Booting using the fdt blob at 0x13000000
   reserving fdt memory region: addr=13000000 size=b000
   Using Device Tree in place at 13000000, end 1300dfff

Starting kernel ...

imx6q-pcie 1ffc000.pcie: phy link never came up
imx6q-pcie 1ffc000.pcie: Failed to bring link up!
imx6q-pcie 1ffc000.pcie: failed to initialize host
fec 2188000.ethernet (unregistered net_device): Invalid MAC address: 00:00:00:00:00:00
fsl-hdmi-dai hdmi_audio.3: failed to probe. Load HDMI-video first.
imx-audio-hdmi sound-hdmi.19: initialize HDMI-audio failed. load HDMI-video first!
Loading, please wait...
fsck from util-linux 2.25.2
jessie: recovering journal
jessie: Clearing orphaned inode 50593 (uid=1000, gid=1000, mode=0100600, size=65536)
jessie: clean, 81329/230608 files, 447036/921344 blocks
/init: 401: /init: touch: not found
adv7180 2-0020: adv7180_read:read reg error: reg=11 ret=-5
egalax_ts 2-0004: Failed to read firmware version
tsc2004_reset: write_cmd -5
tsc2004 2-0048: Failed to reset TSC -5
ft5x06-ts 2-0038: ft5x06: Could not detect touch screen.
ili210x_i2c 2-0041: i2c transfer failed
ili210x_i2c 2-0041: Failed to get firmware version, err: -5
tc358743_read_reg:reg=0 ret=-5
tc358743_probe:cannot find camera
tc358743_probe: failed, error=-19
mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
mxc_v4l_open: Mxc Camera no sensor ipu1/csi0
mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
update_device_addr: ov5642 ret=-5
ov5642_read_reg:write reg error:reg=300a
update_device_addr: ov5640_mipi ret=-5
ov5640_read_reg(mipi):reg=300a ret=-5
[FAILED] Failed to start LSB: Attaching UART to Bluez stack.
See 'systemctl status bluetooth-uart.service' for details.
[  OK  ] Started LSB: SANE network scanner server.
[  OK  ] Started Initialize hardware monitoring sensors.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Login Service.
         Starting Authenticate and Authorize Users to Run Privileged Tasks...
         Starting Light Display Manager...
         Starting Getty on tty1...
[  OK  ] Started Getty on tty1.
         Starting Serial Getty on ttymxc1...
[  OK  ] Started Serial Getty on ttymxc1.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Authenticate and Authorize Users to Run Privileged Tasks.
[  OK  ] Started Network Manager.
[  OK  ] Started Light Display Manager.
[  OK  ] Started Modem Manager.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Debian GNU/Linux 8 nitrogen ttymxc1

nitrogen login: