Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.41-Unraid] (local build)
- Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red
- Device Model: WDC WD30EFRX-68AX9N0
- Serial Number: WD-WCC1T0393079
- LU WWN Device Id: 5 0014ee 2081fc4e3
- Firmware Version: 80.00A80
- User Capacity: 3,000,592,982,016 bytes [3.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ACS-2 (minor revision not indicated)
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Sat May 18 10:24:23 2019 BST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM feature is: Unavailable
- Rd look-ahead is: Enabled
- Write cache is: Enabled
- DSN feature is: Unavailable
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- Wt Cache Reorder: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (37620) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 378) minutes.
- Conveyance self-test routine
- recommended polling time: ( 5) minutes.
- SCT capabilities: (0x70bd) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 36
- 3 Spin_Up_Time POS--K 179 176 021 - 6041
- 4 Start_Stop_Count -O--CK 092 092 000 - 8039
- 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
- 7 Seek_Error_Rate -OSR-K 100 253 000 - 0
- 9 Power_On_Hours -O--CK 033 033 000 - 49201
- 10 Spin_Retry_Count -O--CK 100 100 000 - 0
- 11 Calibration_Retry_Count -O--CK 100 100 000 - 0
- 12 Power_Cycle_Count -O--CK 100 100 000 - 280
- 192 Power-Off_Retract_Count -O--CK 200 200 000 - 179
- 193 Load_Cycle_Count -O--CK 198 198 000 - 7859
- 194 Temperature_Celsius -O---K 115 099 000 - 35
- 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
- 197 Current_Pending_Sector -O--CK 200 200 000 - 0
- 198 Offline_Uncorrectable ----CK 100 253 000 - 0
- 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
- 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 5 Comprehensive SMART error log
- 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x09 SL R/W 1 Selective self-test log
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters log
- 0x21 GPL R/O 1 Write stream error log
- 0x22 GPL R/O 1 Read stream error log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
- 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
- 0xbd GPL,SL VS 1 Device vendor specific log
- 0xc0 GPL,SL VS 1 Device vendor specific log
- 0xc1 GPL VS 93 Device vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
- Device Error Count: 9
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 9 [8] occurred at disk power-on lifetime: 47368 hours (1973 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 00 0c 70 90 40 00 Error: UNC at LBA = 0x000c7090 = 815248
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 04 00 00 00 00 00 00 0c 70 00 40 00 5d+20:15:53.515 READ FPDMA QUEUED
- 60 00 10 00 00 00 00 00 0c 6f f0 40 00 5d+20:15:53.427 READ FPDMA QUEUED
- 60 00 c0 00 00 00 00 00 0c 6f 30 40 00 5d+20:15:53.237 READ FPDMA QUEUED
- 60 00 08 00 00 00 00 00 0c 6f 28 40 00 5d+20:15:53.237 READ FPDMA QUEUED
- 60 01 c8 00 00 00 00 00 0c 6d 60 40 00 5d+20:15:53.236 READ FPDMA QUEUED
- Error 8 [7] occurred at disk power-on lifetime: 47368 hours (1973 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 00 0b e5 f7 40 00 Error: UNC at LBA = 0x000be5f7 = 779767
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 04 00 00 00 00 00 00 0b e3 30 40 00 5d+20:15:37.519 READ FPDMA QUEUED
- 60 00 08 00 00 00 00 00 0b e3 28 40 00 5d+20:15:37.519 READ FPDMA QUEUED
- 60 03 90 00 00 00 00 00 0b df 98 40 00 5d+20:15:37.428 READ FPDMA QUEUED
- 60 04 00 00 00 00 00 00 0b db 98 40 00 5d+20:15:37.425 READ FPDMA QUEUED
- 60 01 b0 00 00 00 00 00 0b d9 e8 40 00 5d+20:15:37.424 READ FPDMA QUEUED
- Error 7 [6] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 10 -- 51 00 00 00 01 49 69 9e e0 40 00 Error: IDNF at LBA = 0x149699ee0 = 5526626016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 61 04 00 00 00 00 01 49 69 9e e0 40 00 27d+22:34:20.268 WRITE FPDMA QUEUED
- 60 00 20 00 00 00 00 72 21 09 18 40 00 27d+22:34:20.241 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 a2 e0 40 00 27d+22:34:20.024 READ FPDMA QUEUED
- 2f 00 00 00 01 00 00 00 00 00 10 40 00 27d+22:34:20.024 READ LOG EXT
- 60 04 00 00 00 00 01 49 69 9e e0 40 00 27d+22:34:13.029 READ FPDMA QUEUED
- Error 6 [5] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 01 49 69 9e e0 40 00 Error: UNC at LBA = 0x149699ee0 = 5526626016
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 04 00 00 00 00 01 49 69 9e e0 40 00 27d+22:34:13.029 READ FPDMA QUEUED
- 61 04 00 00 00 00 01 49 69 96 e0 40 00 27d+22:34:12.984 WRITE FPDMA QUEUED
- 60 00 20 00 00 00 01 0e 83 61 c8 40 00 27d+22:34:12.969 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 9a e0 40 00 27d+22:34:12.752 READ FPDMA QUEUED
- 2f 00 00 00 01 00 00 00 00 00 10 40 00 27d+22:34:12.752 READ LOG EXT
- Error 5 [4] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 01 49 69 96 e0 40 00 Error: UNC at LBA = 0x1496996e0 = 5526623968
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 04 00 00 00 00 01 49 69 96 e0 40 00 27d+22:34:05.757 READ FPDMA QUEUED
- 61 00 20 00 00 00 01 53 6a 3a 68 40 00 27d+22:34:05.741 WRITE FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 92 e0 40 00 27d+22:34:05.712 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 8e e0 40 00 27d+22:34:05.490 READ FPDMA QUEUED
- 2f 00 00 00 01 00 00 00 00 00 10 40 00 27d+22:34:05.490 READ LOG EXT
- Error 4 [3] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 01 53 6a 3a 68 40 00 Error: UNC at LBA = 0x1536a3a68 = 5694437992
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 20 00 00 00 01 53 6a 3a 68 40 00 27d+22:33:58.495 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 8a e0 40 00 27d+22:33:58.482 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 86 e0 40 00 27d+22:33:58.481 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 82 e0 40 00 27d+22:33:58.471 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 7e e0 40 00 27d+22:33:58.469 READ FPDMA QUEUED
- Error 3 [2] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 00 fe f7 20 40 00 Error: UNC at LBA = 0x00fef720 = 16709408
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 20 00 00 00 00 00 fe f7 20 40 00 27d+22:33:42.811 READ FPDMA QUEUED
- 60 00 38 00 00 00 01 49 69 0a e0 40 00 27d+22:33:42.779 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 06 e0 40 00 27d+22:33:42.778 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 69 02 e0 40 00 27d+22:33:42.776 READ FPDMA QUEUED
- 60 03 c8 00 00 00 01 49 68 ff 18 40 00 27d+22:33:42.749 READ FPDMA QUEUED
- Error 2 [1] occurred at disk power-on lifetime: 46705 hours (1946 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 01 00 3a 80 40 00 Error: UNC at LBA = 0x01003a80 = 16792192
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 20 00 00 00 00 01 00 3a 80 40 00 27d+22:33:25.189 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 5e ec 28 40 00 27d+22:33:25.183 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 5e e8 28 40 00 27d+22:33:25.150 READ FPDMA QUEUED
- 60 00 20 00 00 00 00 af d1 d8 50 40 00 27d+22:33:25.121 READ FPDMA QUEUED
- 60 04 00 00 00 00 01 49 5e e4 28 40 00 27d+22:33:25.115 READ FPDMA QUEUED
- SMART Extended Self-test Log Version: 1 (1 sectors)
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed without error 00% 148 -
- # 2 Extended offline Completed without error 00% 71 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 258 (0x0102)
- Device State: Active (0)
- Current Temperature: 35 Celsius
- Power Cycle Min/Max Temperature: 25/40 Celsius
- Lifetime Min/Max Temperature: 15/51 Celsius
- Under/Over Temperature Limit Count: 0/0
- Vendor specific:
- 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -41/85 Celsius
- Temperature History Size (Index): 478 (1)
- Index Estimated Time Temperature Celsius
- 2 2019-05-18 02:27 35 ****************
- ... ..( 11 skipped). .. ****************
- 14 2019-05-18 02:39 35 ****************
- 15 2019-05-18 02:40 36 *****************
- ... ..( 85 skipped). .. *****************
- 101 2019-05-18 04:06 36 *****************
- 102 2019-05-18 04:07 35 ****************
- ... ..( 3 skipped). .. ****************
- 106 2019-05-18 04:11 35 ****************
- 107 2019-05-18 04:12 36 *****************
- ... ..( 6 skipped). .. *****************
- 114 2019-05-18 04:19 36 *****************
- 115 2019-05-18 04:20 35 ****************
- ... ..(363 skipped). .. ****************
- 1 2019-05-18 10:24 35 ****************
- SCT Error Recovery Control:
- Read: 70 (7.0 seconds)
- Write: 70 (7.0 seconds)
- Device Statistics (GP/SMART Log 0x04) not supported
- Pending Defects log (GP Log 0x0c) not supported
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0008 2 0 Device-to-host non-data FIS retries
- 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
- 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
- 0x8000 4 217507 Vendor specific
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement