Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2015.07-15001-g440d481 (Oct 07 2015 - 12:30:57 -0700)
- CPU: Freescale i.MX6Q rev1.2 996 MHz (running at 792 MHz)
- Reset cause: WDOG
- Board: SABRE Lite
- I2C: ready
- DRAM: 1 GiB
- MMC: FSL_SDHC: 0, FSL_SDHC: 1
- SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB
- auto-detected panel 1280x720M@60
- Display: hdmi:1280x720M@60 (1280x720)
- In: serial
- Out: serial
- Err: serial
- Net: using phy at 6
- FEC [PRIME], usb_ether
- Error: usb_ether address not set.
- Hit any key to stop autoboot: 0
- AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
- flags: ncq stag pm led clo only pmp pio slum part
- No port device detected!
- ** Bad device size - sata 0 **
- SATA device 1: unknown device
- ** Bad device sata 1 **
- MMC: no card present
- MMC: no card present
- ** Bad device mmc 0 **
- switch to partitions #0, OK
- mmc1 is current device
- 4439 bytes read in 40 ms (107.4 KiB/s)
- ## Executing script at 10008000
- 74 bytes read in 231 ms (0 Bytes/s)
- 43588 bytes read in 108 ms (393.6 KiB/s)
- only CEA modes allowed on HDMI port
- ----------- trying to load /initrd.img
- 2318305 bytes read in 1419 ms (1.6 MiB/s)
- 5119232 bytes read in 1065 ms (4.6 MiB/s)
- Kernel image @ 0x10800000 [ 0x000000 - 0x4e1d00 ]
- ## Flattened Device Tree blob at 13000000
- Booting using the fdt blob at 0x13000000
- reserving fdt memory region: addr=13000000 size=b000
- Using Device Tree in place at 13000000, end 1300dfff
- Starting kernel ...
- Booting Linux on physical CPU 0x0
- Initializing cgroup subsys cpu
- Linux version 3.14.52-g952e91e-dirty (root@osboxes) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1) ) #2 SMP PREEMPT Wed Sep 28 14:48:05 BST 2016
- CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
- CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine model: Freescale i.MX6 Quad SABRE Lite Board
- cma: CMA: reserved 320 MiB at 3c000000
- Memory policy: Data cache writealloc
- PERCPU: Embedded 7 pages/cpu @ab722000 s8192 r8192 d12288 u32768
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
- Kernel command line: cpu=6Q board=sabrelite mxc_hdmi.only_cea=1 console=ttymxc1,115200 vmalloc=400M consoleblank=0 rootwait fixrtc root=/dev/mmcblk1p1 galcore.contiguousSize=67108864
- PID hash table entries: 4096 (order: 2, 16384 bytes)
- Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- Memory: 699052K/1048576K available (6551K kernel code, 292K rwdata, 2112K rodata, 288K init, 422K bss, 349524K reserved, 0K highmem)
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
- lowmem : 0x80000000 - 0xc0000000 (1024 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .text : 0x80008000 - 0x8087e044 (8665 kB)
- .init : 0x8087f000 - 0x808c7000 ( 288 kB)
- .data : 0x808c8000 - 0x80911240 ( 293 kB)
- .bss : 0x8091124c - 0x8097aa6c ( 423 kB)
- SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- Preemptible hierarchical RCU implementation.
- NR_IRQS:16 nr_irqs:16 16
- L310 cache controller enabled
- l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32470000, Cache size: 1024 kB
- Switching to timer-based delay loop
- sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns
- Console: colour dummy device 80x30
- Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
- CPU: Testing write buffer coherency: ok
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- Setting up static identity map for 0x1066bb20 - 0x1066bb78
- CPU1: Booted secondary processor
- CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- CPU2: Booted secondary processor
- CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
- CPU3: Booted secondary processor
- CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
- Brought up 4 CPUs
- SMP: Total of 4 processors activated (24.00 BogoMIPS).
- CPU: All CPU(s) started in SVC mode.
- devtmpfs: initialized
- VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- pinctrl core: initialized pinctrl subsystem
- regulator-dummy: no parameters
- NET: Registered protocol family 16
- DMA: preallocated 256 KiB pool for atomic coherent allocations
- cpuidle: using governor ladder
- cpuidle: using governor menu
- CPU identified as i.MX6Q, silicon rev 1.2
- Use WDOG1 as reset source
- syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
- vdd1p1: 800 <--> 1375 mV at 1100 mV
- vdd3p0: 2625 <--> 3400 mV at 3000 mV
- vdd2p5: 2000 <--> 2750 mV at 2400 mV
- vddarm: 725 <--> 1450 mV at 1150 mV
- vddpu: 725 <--> 1450 mV at 1150 mV
- vddsoc: 725 <--> 1450 mV at 1175 mV
- syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
- syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
- hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
- hw-breakpoint: maximum watchpoint size is 4 bytes.
- imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
- bio: create slab <bio-0> at 0
- 1P8V: 1800 mV
- 2P5V: 2500 mV
- 3P3V: 3300 mV
- usb_otg_vbus: 5000 mV
- 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58, base_baud = 5000000) is a IMX
- 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX
- console [ttymxc1] enabled
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- i2c i2c-0: IMX I2C adapter registered
- i2c i2c-1: IMX I2C adapter registered
- i2c i2c-2: IMX I2C adapter registered
- media: Linux media interface: v0.10
- Linux video capture interface: v2.00
- pps_core: LinuxPPS API ver. 1 registered
- pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- PTP clock support registered
- imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
- mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
- MIPI CSI2 driver module loaded
- Advanced Linux Sound Architecture Driver Initialized.
- Bluetooth: Core ver 2.18
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO socket layer initialized
- Switched to clocksource mxc_timer1
- NET: Registered protocol family 2
- TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- TCP: reno registered
- UDP hash table entries: 512 (order: 2, 16384 bytes)
- UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- NET: Registered protocol family 1
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- Trying to unpack rootfs image as initramfs...
- Freeing initrd memory: 2260K (83a00000 - 83c35000)
- hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
- imx rpmsg driver is registered.
- imx_busfreq busfreq.15: DDR medium rate not supported.
- Bus freq driver module loaded
- futex hash table entries: 1024 (order: 4, 65536 bytes)
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- NFS: Registering the id_resolver key type
- Key type id_resolver registered
- Key type id_legacy registered
- fuse init (API version 7.22)
- msgmni has been set to 2009
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- backlight_lcd.22 supply power not found, using dummy regulator
- backlight_lvds.23 supply power not found, using dummy regulator
- mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
- fbcvt: 1280x720@60: CVT Name - .921M9
- mxc_sdc_fb fb.20: registered mxc display driver hdmi
- mxc_sdc_fb fb.20: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- find_field: [0] = 0x7ff, max=23
- find_field: [1] = 0xfff, max=23
- find_field: [2] = 0x17ff, max=23
- find_field: [0] = 0x820, max=29
- imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
- mxc_sdc_fb fb.20: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- Console: switching to colour frame buffer device 160x45
- imx-sdma 20ec000.sdma: no iram assigned, using external mem
- imx-sdma 20ec000.sdma: no event needs to be remapped
- imx-sdma 20ec000.sdma: loaded firmware 3.2
- imx-sdma 20ec000.sdma: initialized
- serial: Freescale lpuart driver
- imx sema4 driver is registered.
- [drm] Initialized drm 1.1.0 20060810
- [drm] Initialized vivante 1.0.0 20120216 on minor 0
- mxc_sdc_fb fb.20: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- brd: module loaded
- loop: module loaded
- ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024
- ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480
- ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000
- ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000
- ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
- ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
- ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
- scsi0 : ahci_platform
- ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
- m25p80 spi0.0: sst25vf016b (2048 Kbytes)
- 3 ofpart partitions found on MTD device spi0.0
- Creating 3 MTD partitions on "spi0.0":
- 0x000000000000-0x0000000c0000 : "U-Boot"
- 0x0000000c0000-0x0000000c2000 : "env"
- 0x0000000c2000-0x000000200000 : "splash"
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- spi_imx 2008000.ecspi: probed
- CAN device driver interface
- 2090000.can supply xceiver not found, using dummy regulator
- flexcan 2090000.can: device registered (reg_base=c09e0000, irq=142)
- phyirq=188
- 2188000.ethernet supply phy not found, using dummy regulator
- pps pps0: new PPS source ptp0
- libphy: fec_enet_mii_bus: probed
- fec 2188000.ethernet eth0: registered PHC device 0
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-pci: EHCI PCI platform driver
- usbcore: registered new interface driver cdc_acm
- cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- usbcore: registered new interface driver usb-storage
- usbcore: registered new interface driver usbserial
- usbcore: registered new interface driver usbserial_generic
- usbserial: USB Serial support registered for generic
- usbcore: registered new interface driver cp210x
- usbserial: USB Serial support registered for cp210x
- usbcore: registered new interface driver ftdi_sio
- usbserial: USB Serial support registered for FTDI USB Serial Device
- usbcore: registered new interface driver keyspan
- usbserial: USB Serial support registered for Keyspan - (without firmware)
- usbserial: USB Serial support registered for Keyspan 1 port adapter
- usbserial: USB Serial support registered for Keyspan 2 port adapter
- usbserial: USB Serial support registered for Keyspan 4 port adapter
- usbcore: registered new interface driver pl2303
- usbserial: USB Serial support registered for pl2303
- usbcore: registered new interface driver qcserial
- usbserial: USB Serial support registered for Qualcomm USB modem
- 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
- setup_reset_gpios:-2, flags 0
- setup_reset_gpios:204, flags 1
- mxc_sdc_fb fb.20: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- setup_reset_gpios:-2, flags 0
- 2184200.usb supply vbus not found, using dummy regulator
- ci_hdrc ci_hdrc.1: doesn't support gadget
- ci_hdrc ci_hdrc.1: EHCI Host Controller
- ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- mousedev: PS/2 mouse device common for all mice
- i2c-core: driver [crtouch] using legacy suspend method
- i2c-core: driver [crtouch] using legacy resume method
- egalax_ts 2-0004: Failed to read firmware version
- egalax_ts: probe of 2-0004 failed with error -5
- ft5x06-ts 2-0038: reset fffffffe
- ft5x06-ts 2-0038: Could not detect touch screen -19.
- ili210x_i2c 2-0041: No platform data!
- ili210x_i2c 2-0041: i2c transfer failed
- ili210x_i2c 2-0041: Failed to get firmware version, err: -5
- ili210x_i2c: probe of 2-0041 failed with error -5
- imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_DI0_PIN4 already requested by lcd.21; cannot claim for 2-0048
- imx6q-pinctrl 20e0000.iomuxc: pin-91 (2-0048) status -22
- imx6q-pinctrl 20e0000.iomuxc: could not request pin 91 (MX6Q_PAD_DI0_PIN4) from group i2c3-tsc2004grp on device 20e0000.iomuxc
- tsc2004 2-0048: Error applying setting, reverse things back
- tsc2004_reset: write_cmd -5
- tsc2004 2-0048: Failed to reset TSC -5
- tsc2004: probe of 2-0048 failed with error -5
- snvs_rtc 20cc034.snvs-rtc-lp: can't get snvs-rtc clock
- check_alarm_past: alarm in the past
- snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
- i2c /dev entries driver
- mxc_v4l2_output v4l2_out.28: V4L2 device registered as video16
- mxc_v4l2_output v4l2_out.28: V4L2 device registered as video17
- imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- sdhci-pltfm: SDHCI platform and OF driver helper
- sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode
- mmc0: no vqmmc regulator found
- mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
- sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode
- mmc1: no vqmmc regulator found
- mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
- Galcore version 5.0.11.41671
- mmc1: host does not support reading read-only switch. assuming write-enable.
- mmc1: new high speed SDHC card at address 1234
- mmcblk1: mmc1:1234 SA16G 14.4 GiB
- mmcblk1: p1
- ata1: SATA link down (SStatus 0 SControl 300)
- ahci-imx 2200000.sata: no device found, disabling link.
- ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug
- mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
- mxc_vpu 2040000.vpu: VPU initialized
- mxc_sdc_fb fb.20: 640x480 h_sync,r,l: 96,16,48 v_sync,l,u: 2,10,33 pixclock=25175000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=25175000 25142857 parent=264000000 div=10
- mxc_sdc_fb fb.20: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- caam 2100000.caam: Instantiated RNG4 SH0
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- caam 2100000.caam: Instantiated RNG4 SH1
- caam 2100000.caam: device ID = 0x0a160100 (Era 4)
- caam 2100000.caam: job rings = 2, qi = 0
- caam algorithms registered in /proc/crypto
- caam_jr 2101000.jr0: registering rng-caam
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- sgtl5000 0-000a: sgtl5000 revision 0x11
- 0-000a: 1200 mV normal
- sgtl5000 0-000a: Using internal LDO instead of VDDD
- imx-sgtl5000 sound.18: sgtl5000 <-> 2028000.ssi mapping ok
- imx-audio-hdmi sound-hdmi.19: hdmi-hifi <-> hdmi_audio.3 mapping ok
- NET: Registered protocol family 26
- TCP: cubic registered
- NET: Registered protocol family 10
- sit: IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- can: controller area network core (rev 20120528 abi 9)
- NET: Registered protocol family 29
- can: raw protocol (rev 20120528)
- can: broadcast manager protocol (rev 20120528 t)
- can: netlink gateway (rev 20130117) max_hops=1
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: BNEP socket layer initialized
- 8021q: 802.1Q VLAN Support v1.8
- Key type dns_resolver registered
- Registering SWP/SWPB emulation handler
- imx6q-pcie 1ffc000.pcie: phy link never came up
- imx6q-pcie 1ffc000.pcie: Failed to bring link up!
- imx6q-pcie 1ffc000.pcie: failed to initialize host
- imx6q-pcie: probe of 1ffc000.pcie failed with error -22
- usb_otg_vbus: disabling
- regulator-dummy: disabling
- imx mcc test is registered.
- snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-01 00:03:37 UTC (217)
- ALSA device list:
- #0: imx6q-sabrelite-sgtl5000
- #1: imx-hdmi-soc
- Freeing unused kernel memory: 288K (8087f000 - 808c7000)
- Loading, please wait...
- systemd-udevd[192]: starting version 204
- Begin: Loading essential drivers ... done.
- Begin: Running /scripts/init-premount ... done.
- Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
- Begin: Running /scripts/local-premount ... done.
- EXT4-fs (mmcblk1p1): INFO: recovery required on readonly filesystem
- EXT4-fs (mmcblk1p1): write access will be enabled during recovery
- random: nonblocking pool is initialized
- EXT4-fs (mmcblk1p1): recovery complete
- EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
- Begin: Running /scripts/local-bottom ... done.
- done.
- Begin: Running /scripts/init-bottom ... done.
- init: plymouth-upstart-bridge main process (255) terminated with status 1
- init: plymouth-upstart-bridge main process ended, respawning
- init: plymouth-upstart-bridge main process (264) terminated with status 1
- init: plymouth-upstart-bridge main process ended, respawning
- init: plymouth-upstart-bridge main process (267) terminated with status 1
- init: plymouth-upstart-bridge main process ended, respawning
- init: mounted-proc main process (281) terminated with status 1
- * Starting Mount filesystems on boot [ OK ]
- * Starting Fix-up sensitive /proc filesystem entries [ OK ]
- * Starting Populate /dev filesystem [ OK ]
- * Starting Populate and link to /run filesystem [ OK ]
- * Stopping Populate /dev filesystem [ OK ]
- * Starting Fix-up sensitive /proc filesystem entries [fail]
- * Stopping Populate and link to /run filesystem [ OK ]
- * Stopping Track if upstart is running in a container [ OK ]
- * Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
- * Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
- * Starting Bridge udev events into upstart [ OK ]
- * Starting Signal sysvinit that remote filesystems are mounted [ OK ]
- * Starting device node and kernel event manager [ OK ]
- * Starting Signal sysvinit that the rootfs is mounted [ OK ]
- * Starting load modules from /etc/modules [ OK ]
- * Starting cold plug devices [ OK ]
- * Starting log initial device creation [ OK ]
- * Starting Clean /tmp directory [ OK ]
- * Stopping Clean /tmp directory [ OK ]
- * Starting Signal sysvinit that local filesystems are mounted [ OK ]
- * Stopping load modules from /etc/modules [ OK ]
- * Starting flush early job output to logs [ OK ]
- * Starting setting xorg.conf [ OK ]
- * Stopping Mount filesystems on boot [ OK ]
- * Stopping flush early job output to logs [ OK ]
- * Stopping setting xorg.conf [ OK ]
- * Starting Send an event to indicate plymouth is up [ OK ]
- * Starting D-Bus system message bus [ OK ]
- adv7180 2-0020: adv7180_read:read reg error: reg=11 ret=-5
- mxc_v4l_open: Mxc Camera no sensor ipu1/csi0
- mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
- mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
- mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
- update_device_addr: ov5640_mipi ret=-5
- ov5640_read_reg(mipi):reg=300a ret=-5
- * Starting system logging daemon [ OK ]
- * Stopping Send an event to indicate plymouth is up [ OK ]
- update_device_addr: ov5642 ret=-5
- ov5642_read_reg:write reg error:reg=300a
- * Starting configure network device security [ OK ]
- * Starting bluetooth daemon [ OK ]
- * Starting configure network device [ OK ]
- * Starting SystemD login management service [ OK ]
- * Starting mDNS/DNS-SD daemon [ OK ]
- * Starting Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
- * Stopping Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
- * Stopping cold plug devices [ OK ]
- * Stopping log initial device creation [ OK ]
- * Starting configure network device security [ OK ]
- * Starting save udev log and update rules [ OK ]
- * Stopping save udev log and update rules [ OK ]
- * Starting configure network device security [ OK ]
- * Starting configure network device security [ OK ]
- * Starting configure network device security [ OK ]
- * Starting configure network device [ OK ]
- * Starting Mount network filesystems [ OK ]
- * Starting Failsafe Boot Delay [ OK ]
- * Starting configure network device [ OK ]
- * Starting configure network device security [ OK ]
- * Starting SMB/CIFS File Server [ OK ]
- * Stopping Mount network filesystems [ OK ]
- * Starting configure network device [ OK ]
- * Starting Mount network filesystems [ OK ]
- * Stopping Mount network filesystems [ OK ]
- * Starting Bridge socket events into upstart [ OK ]
- * Starting Bridge file events into upstart [ OK ]
- * Starting SMB/CIFS File and Active Directory Server [ OK ]
- * Starting NetBIOS name server [ OK ]
- * Starting SMB/CIFS File and Active Directory Server [fail]
- * Starting Mount network filesystems [ OK ]
- * Stopping Failsafe Boot Delay [ OK ]
- * Starting System V initialisation compatibility [ OK ]
- * Starting modem connection manager [ OK ]
- * Starting configure network device security [ OK ]
- * Stopping Mount network filesystems [ OK ]
- * Starting configure network device [ OK ]
- * Starting Mount network filesystems [ OK ]
- * Stopping Mount network filesystems [ OK ]
- * Starting configure virtual network devices [ OK ]
- * Starting network connection manager [ OK ]
- * Setting up X socket directories... [ OK ]
- * Stopping System V initialisation compatibility [ OK ]
- * Starting System V runlevel compatibility [ OK ]
- * Starting Restore Sound Card State [ OK ]
- * Starting Freescale autohdmi utility [ OK ]
- * Starting save kernel messages [ OK ]
- * Starting OpenSSH server [ OK ]
- * Starting anac(h)ronistic cron [ OK ]
- * Starting regular background program processing daemon [ OK ]
- * Stopping save kernel messages [ OK ]
- * Stopping Restore Sound Card State [ OK ]
- * Starting cups-browsed - Bonjour remote printer browsing daemon [ OK ]
- * Starting automatic crash report generation [ OK ]
- * Stopping Restore Sound Card State [ OK ]
- * Starting desktop iconset selector: desksel [ OK ]
- * Setting sysfs variables... * unknown attribute class/rfkill/rfkill0/state
- * unknown attribute class/rfkill/rfkill0/type
- * unknown attribute class/rfkill/rfkill0/state
- * unknown attribute class/rfkill/rfkill0/type
- [ OK ]
- * Attaching UART to Bluez stack [ OK ]
- saned disabled; edit /etc/default/saned
- Ubuntu 14.04.5 LTS tengri ttymxc1
Add Comment
Please, Sign In to add comment