U-Boot SPL 2012.10-g6299a25 (Dec 02 2013 - 11:29:49) OMAP4430 ES2.3 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2012.10-g6299a25 (Dec 02 2013 - 11:29:49) CPU : OMAP4430 ES2.3 Board: duovero I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: smc911x-0 Warning: smc911x-0 using MAC address from net device Hit any key to stop autoboot: 0 reading boot.scr ** Unable to read "boot.scr" from mmc 0:1 ** reading uImage 2944112 bytes read Booting from mmc0 ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.6.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2944048 Bytes = 2.8 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.6.0 (scott@hex.jumpnow.it) (gcc version 4.7.2 (GCC) ) #1 SMP Mon Dec 2 11:31:47 EST 2013 [ 0.000000] CPU: ARMv7 Processor [411fc093] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 duovero board [ 0.000000] Reserving 16777216 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] OMAP4430 ES2.3 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0e81000 s12928 r8192 d15744 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 255744 [ 0.000000] Kernel command line: console=ttyO2,115200n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 2097152 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 743MB 264MB = 1007MB total [ 0.000000] Memory: 1013404k/1013404k available, 35172k reserved, 270336K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc054e92c (5403 kB) [ 0.000000] .init : 0xc054f000 - 0xc058b280 ( 241 kB) [ 0.000000] .data : 0xc058c000 - 0xc05e9c48 ( 376 kB) [ 0.000000] .bss : 0xc05e9c6c - 0xc06786b8 ( 571 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:474 [ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] omap_hwmod: sys_32k_ck: missing clockdomain for sys_32k_ck. [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000305] Calibrating delay loop... 1598.59 BogoMIPS (lpj=6242304) [ 0.070251] pid_max: default: 32768 minimum: 301 [ 0.070465] Security Framework initialized [ 0.070617] Mount-cache hash table entries: 512 [ 0.072021] Initializing cgroup subsys debug [ 0.072052] Initializing cgroup subsys cpuacct [ 0.072052] Initializing cgroup subsys memory [ 0.072113] Initializing cgroup subsys devices [ 0.072143] Initializing cgroup subsys freezer [ 0.072143] Initializing cgroup subsys perf_event [ 0.072296] CPU: Testing write buffer coherency: ok [ 0.072601] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.072845] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.072967] Setting up static identity map for 0x803a2a30 - 0x803a2a88 [ 0.072967] L310 cache controller enabled [ 0.072998] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.076049] CPU1: Booted secondary processor [ 0.143157] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.143188] CPU1: Unknown IPI message 0x0 [ 0.143249] Brought up 2 CPUs [ 0.143280] SMP: Total of 2 processors activated (3196.18 BogoMIPS). [ 0.144226] devtmpfs: initialized [ 0.148254] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. [ 0.150604] omap_hwmod: cm_core_aon: cannot be enabled for reset (3) [ 0.150604] omap_hwmod: cm_core: cannot be enabled for reset (3) [ 0.152496] dummy: [ 0.152770] NET: Registered protocol family 16 [ 0.153869] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.154052] GPMC revision 6.0 [ 0.154083] gpmc: irq-52 could not claim: err -22 [ 0.155456] OMAP GPIO hardware version 0.1 [ 0.157073] omap_mux_init: Add partition: #1: core, flags: 2 [ 0.158111] omap_mux_init: Add partition: #2: wkup, flags: 2 [ 0.159118] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.159118] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.171936] usbhs_omap: alias fck already exists [ 0.173553] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.173553] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.175781] OMAP DMA hardware revision 0.0 [ 0.179901] bio: create slab at 0 [ 0.191925] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.192108] vwlan: 3000 mV [ 0.192321] fixed-dummy: [ 0.192840] SCSI subsystem initialized [ 0.193054] usbcore: registered new interface driver usbfs [ 0.193115] usbcore: registered new interface driver hub [ 0.193237] usbcore: registered new device driver usb [ 0.205749] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz [ 0.206146] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.206665] twl 1-0048: PIH (irq 39) chaining IRQs 352..372 [ 0.207183] VUSB: 3300 mV normal standby [ 0.409759] twl6030_usb twl6030_usb: Initialized TWL6030 USB module [ 0.410003] vdd_mpu: 500 <--> 1500 mV normal [ 0.410247] vdd_iva: 500 <--> 1500 mV normal [ 0.410491] vdd_core: 500 <--> 1500 mV normal [ 0.410949] V1V8: 1800 mV normal standby [ 0.411193] V2V1: 2100 mV normal standby [ 0.411590] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.412109] VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.412719] VCXIO: 1800 mV normal standby [ 0.412750] VCXIO: supplied by V2V1 [ 0.413543] VDAC: 1800 mV normal standby [ 0.413574] VDAC: supplied by V2V1 [ 0.414215] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.414764] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.415252] VANA: 2100 mV normal standby [ 0.424438] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz [ 0.440063] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.455688] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz [ 0.455871] Linux video capture interface: v2.00 [ 0.456207] omap-iommu omap-iommu.0: ducati registered [ 0.456268] omap-iommu omap-iommu.1: tesla registered [ 0.456939] Switching to clocksource 32k_counter [ 0.475921] usbhs_omap usbhs_omap: ehci_logic_fck failed:-2 [ 0.476593] NET: Registered protocol family 2 [ 0.477264] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.479125] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.480102] TCP: Hash tables configured (established 131072 bind 65536) [ 0.480163] TCP: reno registered [ 0.480194] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.480255] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.480621] NET: Registered protocol family 1 [ 0.520751] audit: initializing netlink socket (disabled) [ 0.520782] type=2000 audit(0.515:1): initialized [ 0.620880] bounce pool size: 64 pages [ 0.621673] fuse init (API version 7.20) [ 0.621978] msgmni has been set to 1451 [ 0.623138] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.623168] io scheduler noop registered [ 0.623168] io scheduler deadline registered (default) [ 0.623199] io scheduler cfq registered [ 0.623901] OMAP DSS rev 4.0 [ 0.625518] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 0.625885] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 0.626190] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.373107] console [ttyO2] enabled [ 1.377075] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.392333] brd: module loaded [ 1.399505] loop: module loaded [ 1.406280] smsc911x: Driver version 2008-10-21 [ 1.412231] libphy: smsc911x-mdio: probed [ 1.416534] smsc911x smsc911x.0: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=smsc911x-0:01, irq=-1) [ 1.427459] smsc911x smsc911x.0: eth0: MAC Address: 00:15:c9:28:f8:95 [ 1.434356] usbcore: registered new interface driver asix [ 1.440063] usbcore: registered new interface driver cdc_ether [ 1.446258] usbcore: registered new interface driver cdc_ncm [ 1.452392] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.459472] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 1.465606] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 1.503906] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00 [ 1.519500] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 1.525665] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.532775] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.540374] usb usb1: Product: OMAP-EHCI Host Controller [ 1.545959] usb usb1: Manufacturer: Linux 3.6.0 ehci_hcd [ 1.551513] usb usb1: SerialNumber: ehci-omap.0 [ 1.556823] hub 1-0:1.0: USB hub found [ 1.560791] hub 1-0:1.0: 3 ports detected [ 1.565246] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.571868] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller [ 1.578277] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus number 2 [ 1.586334] ohci-omap3 ohci-omap3.0: irq 108, io mem 0x4a064800 [ 1.672607] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.679718] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.687316] usb usb2: Product: OMAP3 OHCI Host Controller [ 1.692962] usb usb2: Manufacturer: Linux 3.6.0 ohci_hcd [ 1.698547] usb usb2: SerialNumber: ohci-omap3.0 [ 1.703948] hub 2-0:1.0: USB hub found [ 1.707885] hub 2-0:1.0: 3 ports detected [ 1.712371] Initializing USB Mass Storage driver... [ 1.717620] usbcore: registered new interface driver usb-storage [ 1.723937] USB Mass Storage support registered. [ 1.728790] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.735565] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using DMA, IRQ 124 [ 1.744354] mousedev: PS/2 mouse device common for all mice [ 1.750640] twl_rtc twl_rtc: Power up reset detected. [ 1.756530] twl_rtc twl_rtc: Enabling TWL-RTC [ 1.763397] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 1.770080] i2c /dev entries driver [ 1.774841] cpuidle: using governor ladder [ 1.779144] cpuidle: using governor menu [ 1.783538] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk [ 1.789825] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 1.796691] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 1.847778] omap_hsmmc omap_hsmmc.4: Failed to get debounce clk [ 1.854003] omap-dma-engine omap-dma-engine: allocating channel for 60 [ 1.860870] omap-dma-engine omap-dma-engine: allocating channel for 59 [ 1.981689] usbcore: registered new interface driver usbhid [ 1.987548] usbhid: USB HID core driver [ 1.991607] OCR: 0 [ 1.991821] oprofile: using arm/armv7-ca9 [ 1.998138] TCP: cubic registered [ 2.001647] host->ocr_avail_sdio: 0 [ 2.001647] NET: Registered protocol family 17 [ 2.001708] Key type dns_resolver registered [ 2.014404] VFP support v0.3: [ 2.014434] Host: 40000 OCR: b0ff8000 implementor 41 architecture 3 part 30 variant 9 rev 4 [ 2.028167] omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0). [ 2.036437] omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).[ 2.045623] Power Management for TI OMAP4. [ 2.050262] ThumbEE CPU extension supported. [ 2.054779] Registering SWP/SWPB emulation handler [ 2.065826] registered taskstats version 1 [ 2.081939] mmc1: new high speed SDIO card at address 0001 [ 2.086151] omapdss error: timeout reading edid [ 2.098266] OCR: 0 [ 2.105499] Console: switching to colour frame buffer device 80x30 [ 2.134735] VANA: incomplete constraints, leaving on [ 2.140808] VDAC: incomplete constraints, leaving on [ 2.146606] VUSB: incomplete constraints, leaving on [ 2.152709] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.161621] Waiting for root device /dev/mmcblk0p2... [ 2.285186] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.295898] mmc0: new high speed SDHC card at address aaaa [ 2.302124] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 2.308074] mmcblk0: p1 p2 p3 [ 2.383575] kjournald starting. Commit interval 5 seconds [ 2.385009] EXT3-fs (mmcblk0p2): using internal journal [ 2.385009] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode [ 2.385040] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.386352] devtmpfs: mounted [ 2.386566] Freeing init memory: 240K INIT: version 2.88 booting Starting udev [ 2.734558] udevd[83]: starting version 182 [ 3.258728] cfg80211: Calling CRDA to update world regulatory domain [ 3.265594] cfg80211: World regulatory domain updated: [ 3.271026] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 3.279663] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3.287872] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3.296051] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 3.304199] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 3.312316] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Wait for CRDA initialization... [ 4.858154] mwifiex_sdio mmc1:0001:1: WLAN FW is active [ 5.146392] cfg80211: Calling CRDA for country: US [ 5.151794] mwifiex_sdio mmc1:0001:1: driver_version = mwifiex 1.0 (14.66.9.p96) [ 5.159942] cfg80211: Regulatory domain changed to country: US [ 5.166137] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 5.174774] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 5.182922] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 5.191070] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 5.199188] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 5.207305] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 5.215454] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 5.223571] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) Configuring network interfaces... Successfully initialized wpa_supplicant udhcpc (v1.20.2) started Sending discover... Sending discover... Sending select for 192.168.10.100... Lease of 192.168.10.100 obtained, lease time 43200 /etc/udhcpc.d/50default: Adding DNS 75.75.75.75 /etc/udhcpc.d/50default: Adding DNS 76.76.76.76 done. Mon Dec 2 20:59:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd done. Starting ntpd: done Starting syslogd/klogd: done [ 11.012145] NET: Registered protocol family 10 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. Poky 9.0.2 (Yocto Project 1.4 Reference Distro) 1.4.2 duovero ttyO2 duovero login: