smartctl 5.42 2011-10-20 r3458 [i386-pc-solaris2.11] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST31500341AS Firmware Version: SD1B User Capacity: 1,500,300,828,160 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat May 19 17:58:05 2012 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 199688128 3 Spin_Up_Time 0x0003 094 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 92 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 12 7 Seek_Error_Rate 0x000f 080 060 030 Pre-fail Always - 103383097 9 Power_On_Hours 0x0032 066 066 000 Old_age Always - 29924 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 1 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 93 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 17180131332 189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 429 190 Airflow_Temperature_Cel 0x0022 058 045 045 Old_age Always In_the_past 42 (Min/Max 39/48) 194 Temperature_Celsius 0x0022 042 055 000 Old_age Always - 42 (0 18 0 0 0) 195 Hardware_ECC_Recovered 0x001a 034 019 000 Old_age Always - 199688128 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 3 SMART Error Log Version: 1 ATA Error Count: 2 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 occurred at disk power-on lifetime: 21305 hours (887 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 30 ff ff ff 4f 00 3d+20:22:57.707 READ FPDMA QUEUED 60 00 30 ff ff ff 4f 00 3d+20:22:57.699 READ FPDMA QUEUED 60 00 50 ff ff ff 4f 00 3d+20:22:57.685 READ FPDMA QUEUED ef 03 46 00 00 00 00 00 3d+20:22:57.675 SET FEATURES [Set transfer mode] ef 03 0c 00 00 00 00 00 3d+20:22:57.665 SET FEATURES [Set transfer mode] Error 1 occurred at disk power-on lifetime: 21305 hours (887 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 30 ff ff ff 4f 00 3d+20:22:54.133 READ FPDMA QUEUED 60 00 50 ff ff ff 4f 00 3d+20:22:54.133 READ FPDMA QUEUED 60 00 30 ff ff ff 4f 00 3d+20:22:54.133 READ FPDMA QUEUED 60 00 50 ff ff ff 4f 00 3d+20:22:54.132 READ FPDMA QUEUED 60 00 30 ff ff ff 4f 00 3d+20:22:54.131 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 29910 - # 2 Short offline Completed without error 00% 29906 - # 3 Conveyance offline Completed without error 00% 29906 - # 4 Extended offline Completed without error 00% 29744 - # 5 Conveyance offline Completed without error 00% 29740 - # 6 Short offline Completed without error 00% 29739 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.