pe2.vtesse#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
pe2.vtesse(config)#int vlan 999
pe2.vtesse(config-if)#ip addr 1.1.1.1
*Jun 12 2014 14:30:29.952 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan999, changed state to down
pe2.vtesse(config-if)#ip addr 1.1.1.1 255.255.255.252
pe2.vtesse(config-if)#
pe2.vtesse(config-if)#
pe2.vtesse(config-if)#
pe2.vtesse(config-if)#mpl
pe2.vtesse(config-if)#mpls ip
pe2.vtesse(config-if)#
pe2.vtesse(config-if)#
pe2.vtesse(config-if)#?
Interface configuration commands:
  aaa             Authentication, Authorization and Accounting.
  arp             Set arp type (arpa, probe, snap), timeout, log options or packet priority
  auto-ip-ring    Auto-IP-Ring interface configuration commands
  bandwidth       Set bandwidth informational parameter
  bfd             BFD interface configuration commands
  bgp-policy      Apply policy propagated by bgp community string
  carrier-delay   Specify delay for interface transitions
  cdp             CDP interface subcommands
  clns            CLNS interface subcommands
  dampening       Enable event dampening
  default         Set a command to its defaults
  delay           Specify interface throughput delay
  description     Interface specific description
  eou             EAPoUDP Interface Configuration Commands
  exit            Exit from interface configuration mode
  help            Description of the interactive help system
  history         Interface history histograms - 60 second, 60 minute and 72 hour
  hold-queue      Set hold queue depth
  ip              Interface Internet Protocol config commands
  ipv6            IPv6 interface subcommands
  isis            IS-IS commands
  iso-igrp        ISO-IGRP interface subcommands
  link            Interface link related commands
  load-interval   Specify interval for load calculation for an interface
  logging         Configure logging for interface
  loopback        Configure internal loopback on an interface
  mac-address     Manually set interface MAC address
  macro           Command macro
  medium          Configure interface medium
  member          Configure the Layer2 VPN member
  mpls            Configure MPLS interface parameters
  mtu             Set the interface Maximum Transmission Unit (MTU)
  no              Negate a command or set its defaults
  ntp             Configure NTP
  ospfv3          OSPFv3 interface commands
  platform        Platform specific commands
  rate-limit      Rate Limit
  service-policy  Configure CPL Service Policy
  shutdown        Shutdown the selected interface
  snmp            Modify SNMP interface parameters
  source          Get config from another source
  spanning-tree   Spanning Tree Subsystem
  srlg            Interface Shared Risk Link Group config commands
  standby         HSRP interface configuration commands
  timeout         Define timeout values for this interface
  topology        Configure routing topology on the interface
  vrf             VPN Routing/Forwarding parameters on the interface
  vrrp            VRRP Interface configuration commands
  vtp             Enable VTP on this interface
  xconnect        Xconnect commands
          
pe2.vtesse(config-if)#exit
pe2.vtesse(config)#no int vlan 999                
pe2.vtesse(config)#
pe2.vtesse#
*Jun 12 2014 14:30:49.252 UTC: %PLATFORM_NCEF-3-NULL_HANDLE:  
ncef_mpls_sb_lfd_obj_delete, Invalid bd handle for vlan 999
-Traceback= 72E944z 30C36B0z 413DFCz 3A476Cz 3A5518z 3A1A10z 3A24F0z 3A263Cz 4865E8z 257E9A4z 2536FD4z 253FB7Cz 25302B0z 64419Cz 64AF58z 65CE5Cz
pe2.vtesse#