#  -*- mode: python; -*-
#============================================================================
# Python configuration setup for 'xm create'.
# This script sets the parameters used when a domain is created using 'xm create'.
# You use a separate script for each domain you want to create, or 
# you can set the parameters for the domain on the xm command line.
#============================================================================

#----------------------------------------------------------------------------
# Kernel image file.
kernel = "hvmloader"

# The domain build function. HVM domain uses 'hvm'.
builder='hvm'

# Initial memory allocation (in megabytes) for the new domain.
#
# WARNING: Creating a domain with insufficient memory may cause out of
#          memory errors. The domain needs enough memory to boot kernel
#          and modules. Allocating less than 32MBs is not recommended.
memory = 2048

# Shadow pagetable memory for the domain, in MB.
# If not explicictly set, xend will pick an appropriate value.  
# Should be at least 2KB per MB of domain memory, plus a few MB per vcpu.
# shadow_memory = 8

# Whether to transparently share this domain's memory with other domains.
# default = 0
# memory_sharing = 0

# A name for your domain. All domains must have different names.
name = "win2k8"

# 128-bit UUID for the domain.  The default behavior is to generate a new UUID
# on each call to 'xm create'.
#uuid = "06ed00fe-1162-4fc4-b5d8-11993ee4a8b9"

#-----------------------------------------------------------------------------
# The number of cpus guest platform has, default=1
vcpus=2

# Enable/disable HVM guest PAE, default=1 (enabled)
#pae=1

# Enable/disable HVM guest ACPI, default=1 (enabled)
#acpi=1

# Enable/disable HVM APIC mode, default=1 (enabled)
# Note that this option is ignored if vcpus > 1
#apic=1

# Enable/disable extended power management support within HVM guest, i.e., beyond
# S3, S4, S5 within guest like exposing battery meter.
# 0 (default option, extended power management support disabled)
# 1 (pass-through mode; uses pass-through as needed; efficient but limited in scope)
# 2 (non pass-through mode; extended scope, likely to work on all applicable environment
#    but comparitively less efficient than pass-through mode)
# xen_extended_power_mgmt=0

# List of which CPUS this domain is allowed to use, default Xen picks
#cpus = ""         # leave to Xen to pick
#cpus = "0"        # all vcpus run on CPU0
#cpus = "0-3,5,^1" # all vcpus run on cpus 0,2,3,5
#cpus = ["2", "3"] # VCPU0 runs on CPU2, VCPU1 runs on CPU3

# Optionally define mac and/or bridge for the network interfaces.
# Random MACs are assigned if not given.
#vif = [ 'type=ioemu, mac=00:16:3e:00:00:11, bridge=xenbr0, model=ne2k_pci' ]
# type=ioemu specify the NIC is an ioemu device not netfront
vif = [ 'type=ioemu, bridge=br0, mac=00:16:3E:22:1E:EF' ]

#----------------------------------------------------------------------------
# Define the disk devices you want the domain to have access to, and
# what you want them accessible as.
# Each disk entry is of the form phy:UNAME,DEV,MODE
# where UNAME is the device, DEV is the device name the domain will see,
# and MODE is r for read-only, w for read-write.

#disk = [ 'phy:hda1,hda1,r' ]
disk = [ 'phy:domU/win2k8,hda,w', 'file:/home/kyl191/win2k8.iso,hdc:cdrom,r' ]

#----------------------------------------------------------------------------
# Configure the behaviour when a domain exits.  There are three 'reasons'
# for a domain to stop: poweroff, reboot, and crash.  For each of these you
# may specify:
#
#   "destroy",        meaning that the domain is cleaned up as normal;
#   "restart",        meaning that a new domain is started in place of the old
#                     one;
#   "preserve",       meaning that no clean-up is done until the domain is
#                     manually destroyed (using xm destroy, for example); or
#   "rename-restart", meaning that the old domain is not cleaned up, but is
#                     renamed and a new domain started in its place.
#
# In the event a domain stops due to a crash, you have the additional options:
#
#   "coredump-destroy", meaning dump the crashed domain's core and then destroy;
#   "coredump-restart', meaning dump the crashed domain's core and the restart.
#
# The default is
#
#   on_poweroff = 'destroy'
#   on_reboot   = 'restart'
#   on_crash    = 'restart'
#
# For backwards compatibility we also support the deprecated option restart
#
# restart = 'onreboot' means on_poweroff = 'destroy'
#                            on_reboot   = 'restart'
#                            on_crash    = 'destroy'
#
# restart = 'always'   means on_poweroff = 'restart'
#                            on_reboot   = 'restart'
#                            on_crash    = 'restart'
#
# restart = 'never'    means on_poweroff = 'destroy'
#                            on_reboot   = 'destroy'
#                            on_crash    = 'destroy'

#on_poweroff = 'destroy'
#on_reboot   = 'restart'
#on_crash    = 'restart'

#============================================================================

# Device Model to be used
device_model = 'qemu-dm'

#-----------------------------------------------------------------------------
# boot on floppy (a), hard disk (c), Network (n) or CD-ROM (d) 
# default: hard disk, cd-rom, floppy
boot="cd"

#-----------------------------------------------------------------------------
#  write to temporary files instead of disk image files
#snapshot=1

#----------------------------------------------------------------------------
# enable SDL library for graphics, default = 0
sdl=0

#----------------------------------------------------------------------------
# enable OpenGL for texture rendering inside the SDL window, default = 1
# valid only if sdl is enabled.
opengl=1

#----------------------------------------------------------------------------
# enable VNC library for graphics, default = 1
vnc=1

#----------------------------------------------------------------------------
# address that should be listened on for the VNC server if vnc is set.
# default is to use 'vnc-listen' setting from
# auxbin.xen_configdir() + /xend-config.sxp
vnclisten="0.0.0.0"

#----------------------------------------------------------------------------
# set VNC display number, default = domid
#vncdisplay=1

#----------------------------------------------------------------------------
# try to find an unused port for the VNC server, default = 1
#vncunused=1

#----------------------------------------------------------------------------
# set password for domain's VNC console
# default is depents on vncpasswd in xend-config.sxp
vncpasswd='password'

#----------------------------------------------------------------------------
# no graphics, use serial port
#nographic=0

#----------------------------------------------------------------------------
# enable stdvga, default = 0 (use cirrus logic device model)
stdvga=0

#-----------------------------------------------------------------------------
#   serial port re-direct to pty deivce, /dev/pts/n 
#   then xm console or minicom can connect
serial='pty'

#----------------------------------------------------------------------------
#   tsc_mode : TSC mode (0=default, 1=native TSC, 2=never emulate, 3=pvrdtscp)
#   emulate TSC provides synced TSC for all vcpus, but lose perfomrance.
#   native TSC leverages hardware's TSC(no perf loss), but vcpu's TSC may lose
#    sync due to hardware's unreliable/unsynced TSC between CPUs.
#   default intelligently uses native TSC on machines where it is safe, but
#    switches to emulated if necessary after save/restore/migration
#   pvrdtscp is for intelligent apps that use special Xen-only paravirtualized
#    cpuid instructions to obtain offset/scaling/migration info and maximize
#    performance within pools of machines that support the rdtscp instruction
tsc_mode=0

#-----------------------------------------------------------------------------
#   Qemu Monitor, default is disable
#   Use ctrl-alt-2 to connect
#monitor=1


#-----------------------------------------------------------------------------
#   enable sound card support, [sb16|es1370|all|..,..], default none
#soundhw='sb16'


#-----------------------------------------------------------------------------
#    set the real time clock to local time [default=0 i.e. set to utc]
#localtime=1


#-----------------------------------------------------------------------------
#    set the real time clock offset in seconds [default=0 i.e. same as dom0]
#rtc_timeoffset=3600

#-----------------------------------------------------------------------------
#    start in full screen
#full-screen=1   


#-----------------------------------------------------------------------------
#   Enable USB support (specific devices specified at runtime through the
#			monitor window)
#usb=1

#   Enable USB mouse support (only enable one of the following, `mouse' for
#			      PS/2 protocol relative mouse, `tablet' for
#			      absolute mouse)
#usbdevice='mouse'
usbdevice='tablet'