U-Boot 1.3.0-rc3-lab126 (Jul 31 2010 - 01:08:40)


CPU:   Freescale i.MX35 at 532 MHz

Board: MX35 Luigi [ POR]

WDOG_WCR = 0xff31

WDOG_WMCR = 0x0

Board Id: SP1B000000000000

S/N: B008A0A003553BE8

DRAM:  256 MB

Using default environment


In:    serial

Out:   serial

Err:   serial

No ethernet found.

i.MX35 CPU board version 2.0

Net:   No ethernet found.

Hit any key to stop autoboot:  1  0 

## Booting image at 87f40400 ...

   Image Name:   Linux-2.6.26-rt-lab126

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    2154316 Bytes =  2.1 MB

   Load Address: 80008000

   Entry Point:  80008000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK


Starting kernel ...


Uncompressing Linux......................................................................................................................... done, booting the kernel.
boot: C def:bcut:batterycut=1:

2.6.26-rt-lab126 #1 Mon Oct 31 01:24:38 CET 2011 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko  (22508 bytes)
Press [ENTER] for recovery menu...       0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/101575 size=3328409600 bytes
flag type      first       last  lba first   lba size
Partition p1:
0x00 0x0b      24072 <large>          7688    6493112
    CHS: 376/0/9 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 3936256
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
  argc == 9
  argv[0]: "kinit"
  argv[1]: "console=ttymxc0,115200"
  argv[2]: "mem=256M"
  argv[3]: "panic=10"
  argv[4]: "root=/dev/mmcblk0p1"
  argv[5]: "ro"
  argv[6]: "ip=none"
  argv[7]: "quiet"
  argv[8]: "lpj=2555904"
Running ipconfig
  argc == 4
  argv[0]: "IP-Config"
  argv[1]: "-i"
  argv[2]: "Linux kinit"
  argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit

INIT: version 2.86 booting

system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[380]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)

lipc-send-event[380]: C def:dbusi::Failed to init dbus

lipc-send-event[380]: E def:open::Failed to open LIPC

lipc-send-event[380]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed

lipc-send-event[478]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)

lipc-send-event[478]: C def:dbusi::Failed to init dbus

lipc-send-event[478]: E def:open::Failed to open LIPC

lipc-send-event[478]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed

system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10filesystems:def:mounting filesystems
system: I S10hostname:def:setting device hostname
system: I S10network:def:initializing network configuration
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (86) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=14420:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan
system: I S45modules:def:loading module g_file_storage
system: I S45modules:def:loading module fuse
system: I S45modules:def:loading module uinput
system: I S45modules:def:loading module mxc_keyb
system: I S45modules:def:loading module fiveway
system: I S45modules:def:loading module volume
system: I rcS:def:starting /etc/rcS.d/S50system
mount: mount point /proc/bus/usb does not exist
Fri Jun  1 00:00:00 UTC 2012
system: I rcS:def:starting /etc/rcS.d/S55scroll
system: I S55scroll:def:skipping; no luigi-based work to do here
system: I rcS:def:starting /etc/rcS.d/S70ethernet
system: I rcS:def:starting /etc/rcS.d/S70userstore
system: I S70ethernet:def:not enet
system: I S70ethernet:def:not usbnet
system: I S70userstore:def:Found BOOTUP flag file
dosfsck 2.11-lab126 (1 Jun 2007)
dosfsck 2.11-lab126, 1 Jun 2007, FAT32, LFN
Checking we can access the last sector of the filesystem
There are differences between boot sector and its backup.
Differences: (offset:original/backup)
  65:01/00
  Not automatically fixing this.
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
      8192 bytes per cluster
        32 reserved sectors
First FAT starts at byte 16384 (sector 32)
         2 FATs, 32 bit entries
   1601536 bytes per FAT (= 3128 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 3219456 (sector 6288)
    400274 data clusters (3279044608 bytes)
32 sectors/track, 64 heads
         0 hidden sectors
   6410672 sectors total
A new long file name starts within an old one.
  Not auto-correcting this.
A new long file name starts within an old one.
  Not auto-correcting this.
A new long file name starts within an old one.
  Not auto-correcting this.
Unfinished long file name ":621:3LH:5rx:3b0:7iu:CWH:6Gh:Bn9:Dh5:9f8:AYc:5sp:3IW".
  (Start may have been overwritten by \024.\036\226\207\013;k.\202)
  Not auto-correcting this.
Wrong checksum for long file name ":621:3LH:5rx:3b0:7iu:CWH:6Gh:Bn9:Dh5:9f8:AYc:5sp:3IW".
  (Short name \024.\036\226\207\013;k.\202 may have changed without updating the long name)
  Not auto-correcting this.
Long filename fragment ":C+8:3wp:1+J:0tt:DsR:8ra:9Kp:0zE:Dk4:95P:6NX:6b7:43h" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (98 vs. expected bc).
  Not auto-correcting this.
Checking for unused clusters.
Checking free cluster summary.
/dev/loop/0: 674 files, 24093/400274 clusters
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use

INIT: Entering runlevel: 2

system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Fri Jun  1 08:45:06 2012  INFO:battery voltage: 3696 mV
Fri Jun  1 08:45:06 2012  INFO:battery charge: 15%
system: I S50battcheck:def:current voltage = 3696mV
Fri Jun  1 08:45:06 2012  INFO:battery charge: 15%
Fri Jun  1 08:45:06 2012  INFO:battery voltage: 3696 mV
Fri Jun  1 08:45:06 2012  INFO:battery current: -205 mA
system: I S50battcheck:def:gasgauge capacity=15% volts=3696 mV current=-205 mA
system: I S50battcheck:def:Waiting for 3460mV or 4%
system: I S50battcheck:def:battery sufficient, booting to normal runlevel

INIT: Switching to runlevel: 5


INIT: Sending processes the TERM signal

Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
No debug record limit set
Load Board Data from /opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin
Updating MAC address
BMI Set App Start (address: 0x913950)
BMI Bit-Wise (OR) modify Register (address: 0x500410, orig:0x8, new: 0x9,  mask:0x1)
BMI Write compressed Memory (address: 0x502070, filename: /opt/ar6k/target/AR6002/hw2.0/bin/athwlan.bin.z77)
BMI Write Memory (address: 0x52d6d0, filename: /opt/ar6k/target/AR6002/hw2.0/bin/data.patch.hw2_0.bin)
BMI Write Memory (address: 0x500418, value: 0x52d6d0)
BMI Done
system: I wifi:def:loadAR6000=finished, args=():
system: I wpa_supplicant:def:wpa supplicant started
system: I S30network:def:initializing network configuration
system: I S30network:def:Installed Firewall
system: I S60dbus:def:starting system message bus
system: W S64linkjail:def:couldn't run unlinkjail
Starting Process Monitoring Daemon: Retrieved 136 keys for system/daemon/pmond/
Starting Power Management Daemon: system: I S70wifid:def:starting wifid
system: I S70cmd:def:starting CMD daemon
system: I S75phd:def:Starting Phone-Home Daemon
system: I S76mcsd:def:starting MCS server
system: I S80volumd:def:starting Volume daemon
system: I S82usbnet:def:usbnet is disabled
system: I S85audio:def:initializing audio driver defaults
No state is present for card mx35luigi
system: I S85audio:def:starting audio server
system: I S87ttsd:def:starting TTS daemon
Battery Level: 15%
Sun Jul  7 18:26:23 2013  INFO:battery charge: 15%
Starting lipc-daemon: system: I S90cron:def:starting crond
system: I S90tmd:def:Starting Transfer Manager Daemon
system: I S93webreaderd:def:Starting WebReader Daemon
system: I S94browserd:def:Starting Browser Daemon
system: I S95framework:def:starting booklet framework
system: I S95framework:def:logging reset type: hard
system: I S96boot_finished:def:Boot finished script running
system: I S96boot_finished:symboot:time=40850:boot time before framework starts, in milliseconds
system: I mntroot:def:Making root filesystem read-only
start.sh: starting framework






Welcome to Kindle!



kindle login: 
system: I S96boot_finished:def:Boot finished script received framework booted event
system: I S96boot_finished:fwboot:time=83160:boot time after framework starts, in milliseconds
system: I loginfo:devhw:boardID=SP1B:Shasta PVT device - rev 1
system: I loginfo:devhwphy::USB PHY built by unknown
system: I loginfo:devsworig::Original System Software Version: 040-S4_luigi-172597
Sat Sep 1 14:29:41 PDT 2012
system: I loginfo:devswota::OTA  Kindle 3.4 (~~otaVersion~~)
com.lab126.wan failed to access property localTimeOffset (0x3 lipcErrNoSuchSource)
system: W loginfo:ltofailwandoff:cannot retrieve local time offset - wand not running
com.lab126.powerd failed to set value for property wakeUp (0x8 lipcErrNoSuchProperty)
system: I ckimage:def:cannot determine current kernel partition bailing out until next time
system: I governor:def:switching to ondemand governor
system: I tinyrot:def::Rotating file /var/log/messages with max size 256
/usr/sbin/tinyrot : Signaling syslog
/usr/sbin/tinyrot : Calculating total size /var/local/log/messages_*.gz
/usr/sbin/tinyrot : Total size of /var/local/log/messages_*.gz is 85kb
system: I tinyrot:def::Rotating file /var/log/odotlite with max size 2048
system: I tinyrot:def::No file to rotate: /var/log/odotlite