Show status of drive: Status of drive /dev/sda Location SATA device A Drive size 1.86 TB Make and model ATA HGST HUS724020AL Supports SMART? Yes SMART enabled? Yes Errors logged 1 errors detected Passed drive check? Yes Make and model HGST HUS724020ALA640 Serial number PN1134P6HTEZHW Capacity 2,000,398,934,016 bytes [2.00 TB] Additional SMART attributes Offline data collection status Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection 28 seconds. Offline data collection capabilities SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time 1 minutes. Extended self-test routine recommended polling time 255 minutes. SCT capabilities SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. Raw Read Error Rate 0 (Normalized: 100) Throughput Performance 85 (Normalized: 135) Spin Up Time 405 (Normalized: 100) Start Stop Count 9 (Normalized: 100) Reallocated Sector Ct 0 (Normalized: 100) Seek Error Rate 0 (Normalized: 100) Seek Time Performance 25 (Normalized: 142) Power On Hours 4095 (Normalized: 100) Spin Retry Count 0 (Normalized: 100) Power Cycle Count 9 (Normalized: 100) Power-Off Retract Count 9 (Normalized: 100) Load Cycle Count 9 (Normalized: 100) Temperature Celsius 32 (Normalized: 187) Reallocated Event Count 0 (Normalized: 100) Current Pending Sector 0 (Normalized: 100) Offline Uncorrectable 0 (Normalized: 100) Full SMART status report smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.14.32-xxxx-grs-ipv6-64] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: HGST HUS724020ALA640 Serial Number: PN1134P6HTEZHW LU WWN Device Id: 5 000cca 22dd934e7 Firmware Version: MF6OAA70 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Feb 11 15:47:45 2015 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 28) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 85 3 Spin_Up_Time 0x0007 100 100 024 Pre-fail Always - 405 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 9 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 142 142 020 Pre-fail Offline - 25 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 4095 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 9 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 9 194 Temperature_Celsius 0x0002 187 187 000 Old_age Always - 32 (Min/Max 25/43) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 102 hours (4 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 31 89 03 50 08 Error: WP at LBA = 0x08500389 = 139461513 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 01 30 a9 14 ed 40 00 1d+02:10:28.119 WRITE FPDMA QUEUED 61 01 28 ab 14 ed 40 00 1d+02:10:28.119 WRITE FPDMA QUEUED 61 01 20 ad 14 ed 40 00 1d+02:10:28.119 WRITE FPDMA QUEUED 61 01 18 af 14 ed 40 00 1d+02:10:28.119 WRITE FPDMA QUEUED 61 01 10 b1 14 ed 40 00 1d+02:10:28.119 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4053 - # 2 Short offline Completed without error 00% 4050 - # 3 Short offline Completed without error 00% 4050 - # 4 Short offline Completed without error 00% 4045 - # 5 Short offline Completed without error 00% 4045 - # 6 Short offline Completed without error 00% 3992 - # 7 Short offline Completed without error 00% 3988 - # 8 Short offline Completed without error 00% 85 - # 9 Short offline Completed without error 00% 85 - #10 Short offline Completed without error 00% 77 - #11 Short offline Completed without error 00% 17 - #12 Short offline Completed without error 00% 3 - #13 Short offline Completed without error 00% 1 - #14 Short offline Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.