EVK U-Boot > sata dev 0
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part 
SATA Device Info:
S/N: 
Product model number: 
Firmware version: 
Capacity: 625142448 sectors

SATA device 0: Model:  Firm:  Ser#: 
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
... is now current device
EVK U-Boot > ext2load sata 0 0x70800000 uImage
Loading file "uImage" from sata device 0:1 (hda1)
2480280 bytes read
EVK U-Boot > bootm
## Booting kernel from Legacy Image at 70800000 ...
   Image Name:   linux-2.6
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2480216 Bytes =  2.4 MB
   Load Address: 70008000
   Entry Point:  70008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 2.6.35.3-1129-g691c08a (user@imx535-bld) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #288 PREEMPT Sun Dec 9 16:55:10 UTC 2012
CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Freescale MX53 LOCO Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56896
Kernel command line: console=ttymxc0,115200n8 root=/dev/sda1 rw rootwait rootfstype=ext3
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 224MB = 224MB total
Memory: 222312k/222312k available, 7064k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf9e00000 - 0xffe00000   (  96 MB)
    vmalloc : 0x8e800000 - 0xf4000000   (1624 MB)
    lowmem  : 0x80000000 - 0x8e000000   ( 224 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .init : 0x80008000 - 0x80028000   ( 128 kB)
      .text : 0x80028000 - 0x80472000   (4392 kB)
      .data : 0x80490000 - 0x804ccf40   ( 244 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:368
MXC GPIO hardware
MXC IRQ initialized
MXC_Early serial console at MMIO 0x53fbc000 (options '115200n8')
bootconsole [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
regulator: dummy: 
NET: Registered protocol family 16
i.MX IRAM pool: 128 KB@0x8e840000
IRAM READY
FEC PHY freq 50000000
CPU is i.MX53 Revision 2.1
Using SDMA I.API
MXC DMA API initialized
IMX usb wakeup probe
IMX usb wakeup probe
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
LPMode driver module loaded
Static Power Management for Freescale i.MX5
PM driver module loaded
sdram autogating driver module loaded
Bus freq driver module loaded
DI0 is primary
mxc_dvfs_core_probe
regulator: get() with no identifier
mxc_dvfs_core_probe: failed to get gp regulator
DVFS driver module loaded
i.MXC CPU frequency driver
regulator: get() with no identifier
mxc_cpufreq_driver_init: failed to get gp regulator
DVFS PER driver module loaded
msgmni has been set to 434
alg: No test for stdrng (krng)
cryptodev: driver loaded.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
regulator: get() with no identifier
mxc_ipu mxc_ipu: Channel already disabled 9
mxc_ipu mxc_ipu: Channel already uninitialized 9
Console: switching to colour frame buffer device 100x30
mxc_ipu mxc_ipu: Channel already disabled 7
mxc_ipu mxc_ipu: Channel already uninitialized 7
mxc_ipu mxc_ipu: Channel already disabled 10
mxc_ipu mxc_ipu: Channel already uninitialized 10
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
console [ttymxc0] enabled, bootconsole disabled
console [ttymxc0] enabled, bootconsole disabled
mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX
mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX
loop: module loaded
NO SATA device is found, relase resource!
MXC MTD nand Driver 3.0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
RedBoot partition parsing not available
Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000002000000 : "bootloader and kernel"
0x000002000000-0x000010000000 : "nand.rootfs"
vcan: Virtual CAN interface driver
flexcan netdevice driver
flexcan imx53-flexcan.0: device registered (reg_base=8e930000, irq=82)
flexcan imx53-flexcan.1: device registered (reg_base=8e938000, irq=83)
CAN device driver interface
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
spi0.0 supply vcc not found, using dummy regulator
ads7846 spi0.0: touchscreen, irq 214
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.0/spi0.0/input/input0
spi1.0 supply vcc not found, using dummy regulator
ads7846 spi1.0: touchscreen, irq 211
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.1/spi1.0/input/input1
spi2.0 supply vcc not found, using dummy regulator
ads7846 spi2.0: touchscreen, irq 166
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.2/spi2.0/input/input2
rtc-ds1307 1-0068: rtc core: registered ds1338 as rtc0
rtc-ds1307 1-0068: 56 bytes nvram
mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc1
i2c /dev entries driver
Linux video capture interface: v2.00
usb 2-1: new low speed USB device using fsl-ehci and address 2
mxc_v4l2_output mxc_v4l2_output.0: Registered device video1
MXC WatchDog Driver 2.0
MXC Watchdog # 0 Timer: initial timeout 60 sec
VPU initialized
mxc_asrc registered
gpu mmu enabled
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver. 
mmc0: SDHCI detect irq 206 irq 1 INTERNAL DMA
input: USB USB Keykoard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1:1.0/input/input3
generic-usb 0003:1A2C:0002.0001: input: USB HID v1.10 Keyboard [USB USB Keykoard] on usb-fsl-ehci.1-1/input0
drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed
generic-usb 0003:1A2C:0002.0002: timeout initializing reports
input: USB USB Keykoard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1:1.1/input/input4
generic-usb 0003:1A2C:0002.0002: input: USB HID v1.10 Device [USB USB Keykoard] on usb-fsl-ehci.1-1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
No device for DAI tlv320aic23
No device for DAI imx-ssi-1-0
No device for DAI imx-ssi-1-1
No device for DAI imx-ssi-2-0
No device for DAI imx-ssi-2-1
AIC23 Audio Codec 0.1
DMA Sound Buffer Allocated: Playback UseIram=1 ext_ram=0 buf->addr=f8016000 buf->area=8e856000 size=24576
DMA Sound Buffer Allocated: Capture  UseIram=1 ext_ram=1 buf->addr=7d1f8000 buf->area=fa8ad000 size=24576
asoc: tlv320aic23 <-> imx-ssi-2-0 mapping ok
ALSA device list:
  #0: imx-3stack (tlv320aic23)
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
rtc-ds1307 1-0068: setting system clock to 2013-01-23 20:04:00 UTC (1358971440)
Waiting for root device /dev/sda1...