Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.11 (FAFNER) #0: Sat Sep 22 14:31:04 CEST 2012
        bjorn@fafner:/usr/obj/sys/arch/i386/compile/FAFNER
total memory = 991 MB
avail memory = 967 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Packard Bell BV IMEDIA MC 2590 (PB34345891)
mainbus0 (root)
cpu0 at mainbus0 apid 0timecounter: Timecounter "lapic" frequency 199594333 Hz quality -100
: Intel(R) Pentium(R) 4 CPU 3.00GHz, id 0xf49
cpu1 at mainbus0 apid 1: Intel(R) Pentium(R) 4 CPU 3.00GHz, id 0xf49
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <PacBel,PBDTNB00,11000607>, AslId <MSFT,00000097>
ACPI Error: Method parse/execution failed [\_PR_.CPU1._PDC] (Node 0xc19b6484), AE_INVALID_TABLE_LENGTH (20110623/psparse-560)
ACPI Error: Method parse/execution failed [\_PR_.CPU2._PDC] (Node 0xc19b6584), AE_INVALID_TABLE_LENGTH (20110623/psparse-560)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
spkr0 at pcppi1
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
RMSC (PNP0C02) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
SIOR (PNP0C02) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
THRM (ACPI Object Type 'Thermal') at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pci_mem_find: 64-bit memory map which is inaccessible on a 32-bit platform
pchb0 at pci0 dev 0 function 0: vendor 0x1002 product 0x5a33 (rev. 0x01)
ppb0 at pci0 dev 1 function 0: vendor 0x1002 product 0x5a3f (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 5 function 0: vendor 0x1002 product 0x5a61 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
radeondrm0 at vga0: ATI Radeon RC410 XPRESS 200
radeondrm0: Initialized radeon 1.29.0 20080613
ppb1 at pci0 dev 7 function 0: vendor 0x1002 product 0x5a39 (rev. 0x00)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x1033 product 0x0194 (USB serial bus, interface 0x30, revision 0x03) at pci2 dev 0 function 0 not configured
ixpide0 at pci0 dev 18 function 0: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ixpide0: using ioapic0 pin 22 for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 19 function 0: vendor 0x1002 product 0x4387 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 19 function 1: vendor 0x1002 product 0x4388 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 17
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ohci2 at pci0 dev 19 function 2: vendor 0x1002 product 0x4389 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb2 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 3: vendor 0x1002 product 0x438a (rev. 0x00)
ohci3: interrupting at ioapic0 pin 17
ohci3: OHCI version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
ohci4 at pci0 dev 19 function 4: vendor 0x1002 product 0x438b (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb4 at ohci4: USB revision 1.0
ehci0 at pci0 dev 19 function 5: vendor 0x1002 product 0x4386 (rev. 0x00)
ehci0: applying AMD SB600/SB700 USB freeze workaround
ehci0: interrupting at ioapic0 pin 19
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1 ohci2 ohci3 ohci4
usb5 at ehci0: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x13)
piixpm0: interrupting at SMI, polling
iic0 at piixpm0: I2C bus
ixpide1 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ixpide1: primary channel interrupting at ioapic0 pin 14
atabus2 at ixpide1 channel 0
ixpide1: secondary channel configured to compatibility mode
ixpide1: secondary channel interrupting at ioapic0 pin 15
atabus3 at ixpide1 channel 1
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x438d (rev. 0x00)
ppb2 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
emuxki0 at pci3 dev 1 function 0: vendor 0x1102 product 0x0002 (rev. 0x07)
emuxki0: interrupting at ioapic0 pin 21
emuxki0: ac97: SigmaTel STAC9721/23 codec; 18 bit DAC, 18 bit ADC, SigmaTel 3D
emuxki0: ac97: ext id 0x200<AMAP>
audio0 at emuxki0: full duplex, playback, capture, mmap, independent
vendor 0x1102 product 0x7002 (miscellaneous input, revision 0x07) at pci3 dev 1 function 1 not configured
wm0 at pci3 dev 2 function 0: Intel i82541PI 1000BASE-T Ethernet (rev. 0x05)
wm0: interrupting at ioapic0 pin 22
wm0: 32-bit 33MHz PCI bus
wm0: 64 word (6 address bits) MicroWire EEPROM
wm0: Ethernet address xx:xx:xx:xx:xx:xx
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
rtk0 at pci3 dev 5 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at ioapic0 pin 20
rtk0: Ethernet address xx:xx:xx:xx:xx:xx
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
acpicpu0 at cpu0: ACPI CPU
pci_mem_find: 64-bit memory map which is inaccessible on a 32-bit platform
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu1 at cpu1: ACPI CPU
pci_mem_find: 64-bit memory map which is inaccessible on a 32-bit platform
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2992659830 Hz quality 3000
IPsec: Initialized Security Association Processing.
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 10 ports with 10 removable, self powered
ugen0 at uhub1 port 2
ugen0: American Power Conversion Back-UPS CS 350 FW:807.q7.I USB FW:q7, rev 1.10/0.06, addr 2
wd0 at atabus0 drive 0
wd0: <ST3250820AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1 at atabus1 drive 0
wd1: <ST3250820AS>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ixpide0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <PHILIPS DVD8801, , NW02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(ixpide1:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
uhub4: device problem, disabling port 1
uhub4: device problem, disabling port 1