Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- X-Loader 1.5.1 (Jan 22 2012 - 11:08:14)
- OMAP3630/3730-GP ES2.1
- Board revision: 1
- Reading boot sector
- Loading u-boot.bin from mmc
- U-Boot 2011.09 (Jan 06 2012 - 13:51:09)
- OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
- Gumstix Overo board + LPDDR/NAND
- I2C: ready
- DRAM: 512 MiB
- NAND: 512 MiB
- MMC: OMAP SD/MMC: 0
- In: serial
- Out: serial
- Err: serial
- Board revision: 1
- Direct connection on mmc2
- No EEPROM on expansion board
- Die ID #0d8e00229ff800000168301016022002
- Net: smc911x-0
- Hit any key to stop autoboot: 0
- reading boot.scr
- 691 bytes read
- Running bootscript from mmc ...
- ## Executing script at 82000000
- Booting Linux from mmc...
- ## Error: "i2c-speed" not defined
- Using i2c configuration: 3,200
- reading uImage
- 2619768 bytes read
- reading uInitrd
- 2617451 bytes read
- ## Booting kernel from Legacy Image at 80000000 ...
- Image Name: Linux-3.0.22-rt37+
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2619704 Bytes = 2.5 MiB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- ## Loading init Ramdisk from Legacy Image at 81600000 ...
- Image Name: initramfs
- Image Type: ARM Linux RAMDisk Image (uncompressed)
- Data Size: 2617387 Bytes = 2.5 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Linux version 3.0.22-rt37+ (lutz_ph@pemphredo) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #52 PREEMPT RT Thu Mar 15 12:03:16 CET 2012
- CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
- CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine: Gumstix Overo
- Reserving 12582912 bytes SDRAM for VRAM
- Memory policy: ECC disabled, Data cache writeback
- OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
- SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
- On node 0 totalpages: 126464
- free_area_init_node: node 0, pgdat c0512c70, node_mem_map c0568000
- Normal zone: 1024 pages used for memmap
- Normal zone: 0 pages reserved
- Normal zone: 125440 pages, LIFO batch:31
- Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
- Reprogramming SDRC clock to 332000000 Hz
- pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- pcpu-alloc: [0] 0
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125440
- Kernel command line: console=ttyO2,115200n8 elevator=noop vram=12M omapfb.mode=dvi:1280x720MR-16@60 mpurate=900 root=/dev/mmcblk0p2 ro rootwait raid=noautodetect noplymouth 0
- PID hash table entries: 2048 (order: 1, 8192 bytes)
- Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- Memory: 494MB = 494MB total
- Memory: 493216k/493216k available, 31072k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
- vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
- lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- .init : 0xc0008000 - 0xc0035000 ( 180 kB)
- .text : 0xc0035000 - 0xc04cd228 (4705 kB)
- .data : 0xc04ce000 - 0xc05133e0 ( 277 kB)
- .bss : 0xc0513404 - 0xc0567d88 ( 339 kB)
- Preemptible hierarchical RCU implementation.
- NR_IRQS:410
- IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- Total of 96 interrupts on 1 active controller
- OMAP clockevent source: GPTIMER1 at 32768 Hz
- sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
- Console: colour dummy device 80x30
- Calibrating delay loop... 595.04 BogoMIPS (lpj=290816)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- devtmpfs: initialized
- omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
- omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
- omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
- omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
- omap_hwmod: i2c1: softreset failed (waited 10000 usec)
- omap_hwmod: i2c2: softreset failed (waited 10000 usec)
- omap_hwmod: i2c3: softreset failed (waited 10000 usec)
- print_constraints: dummy:
- NET: Registered protocol family 16
- GPMC revision 5.0
- OMAP GPIO hardware version 2.5
- OMAP GPIO hardware version 2.5
- OMAP GPIO hardware version 2.5
- OMAP GPIO hardware version 2.5
- OMAP GPIO hardware version 2.5
- OMAP GPIO hardware version 2.5
- omap_mux_init: Add partition: #1: core, flags: 0
- Found NAND on CS0
- Registering NAND on CS0
- hw-breakpoint: debug architecture 0x4 unsupported.
- Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/900 MHz
- OMAP DMA hardware revision 5.0
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz
- twl4030: PIH (irq 7) chaining IRQs 368..375
- twl4030: power (irq 373) chaining IRQs 376..383
- twl4030: gpio (irq 368) chaining IRQs 384..401
- machine_constraints_voltage: VUSB1V5: override min_uV, 1 -> 1500000
- machine_constraints_voltage: VUSB1V5: override max_uV, 2147483647 -> 1500000
- print_constraints: VUSB1V5: 1500 mV normal standby
- machine_constraints_voltage: VUSB1V8: override min_uV, 1 -> 1800000
- machine_constraints_voltage: VUSB1V8: override max_uV, 2147483647 -> 1800000
- print_constraints: VUSB1V8: 1800 mV normal standby
- machine_constraints_voltage: VUSB3V1: override min_uV, 1 -> 3100000
- machine_constraints_voltage: VUSB3V1: override max_uV, 2147483647 -> 3100000
- print_constraints: VUSB3V1: 3100 mV normal standby
- twl4030_usb twl4030_usb: HW_CONDITIONS 0x10/16; link 0
- twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby
- print_constraints: VDAC: 1800 mV normal standby
- print_constraints: VDVI: 1800 mV normal standby
- omap_i2c omap_i2c.3: bus 3 rev4.0 at 200 kHz
- Switching to clocksource 32k_counter
- Switched to NOHz mode on CPU #0
- musb-hdrc: version 6.0, musb-dma, host
- twl4030_usb twl4030_usb: twl4030_phy_resume
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 1.800
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- musb-hdrc musb-hdrc: MUSB HDRC host driver
- drivers/usb/core/inode.c: creating file 'devices'
- drivers/usb/core/inode.c: creating file '001'
- musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
- usb usb1: default language 0x0409
- usb usb1: udev 1, busnum 1, minor = 0
- usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb1: Product: MUSB HDRC host driver
- usb usb1: Manufacturer: Linux 3.0.22-rt37+ musb-hcd
- usb usb1: SerialNumber: musb-hdrc
- usb usb1: usb_probe_device
- usb usb1: configuration #1 chosen from 1 choice
- usb usb1: adding 1-0:1.0 (config #1, interface 0)
- hub 1-0:1.0: usb_probe_interface
- hub 1-0:1.0: usb_probe_interface - got id
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- hub 1-0:1.0: standalone hub
- hub 1-0:1.0: individual port power switching
- hub 1-0:1.0: no over-current protection
- hub 1-0:1.0: Single TT
- hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
- hub 1-0:1.0: power on to power good time: 10ms
- hub 1-0:1.0: 100mA bus power budget for each child
- hub 1-0:1.0: local power source is good
- hub 1-0:1.0: enabling power on all ports
- drivers/usb/core/inode.c: creating file '001'
- musb-hdrc musb-hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
- NET: Registered protocol family 2
- IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- TCP bind hash table entries: 16384 (order: 6, 393216 bytes)
- TCP: Hash tables configured (established 16384 bind 16384)
- TCP reno registered
- UDP hash table entries: 256 (order: 2, 16384 bytes)
- UDP-Lite hash table entries: 256 (order: 2, 16384 bytes)
- NET: Registered protocol family 1
- Trying to unpack rootfs image as initramfs...
- twl4030_usb twl4030_usb: HW_CONDITIONS 0x90/144; link 1
- hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
- Freeing initrd memory: 2556K
- omap_dsp_init: 600000 bytes @ 9ee00000
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- msgmni has been set to 968
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
- io scheduler noop registered (default)
- io scheduler deadline registered
- io scheduler cfq registered
- OMAP DSS rev 2.0
- Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
- omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
- omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
- console [ttyO2] enabled
- omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
- brd: module loaded
- loop: module loaded
- omap2-nand driver initializing
- ONFI flash detected
- NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
- Creating 5 MTD partitions on "omap2-nand.0":
- 0x000000000000-0x000000080000 : "xloader"
- 0x000000080000-0x000000240000 : "uboot"
- 0x000000240000-0x000000280000 : "uboot environment"
- 0x000000280000-0x000000680000 : "linux"
- 0x000000680000-0x000020000000 : "rootfs"
- smsc911x: Driver version 2008-10-21
- smsc911x-mdio: probed
- smsc911x smsc911x.0: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
- smsc911x smsc911x.0: eth0: MAC Address: 00:15:c9:28:da:fa
- smsc911x: Driver version 2008-10-21
- usbcore: registered new interface driver asix
- usbcore: registered new interface driver cdc_ether
- usbcore: registered new interface driver cdc_eem
- usbcore: registered new interface driver dm9601
- usbcore: registered new interface driver smsc75xx
- usbcore: registered new interface driver smsc95xx
- cdc_ncm: 04-Aug-2011
- usbcore: registered new interface driver cdc_ncm
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
- ehci-omap ehci-omap.0: failed to get ehci port1 regulator
- ehci-omap ehci-omap.0: phy reset operation timed out
- ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
- ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
- ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
- drivers/usb/core/inode.c: creating file '002'
- ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
- ehci-omap ehci-omap.0: park 0
- ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
- ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
- ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
- ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- usb usb2: default language 0x0409
- usb usb2: udev 1, busnum 2, minor = 128
- usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb2: Product: OMAP-EHCI Host Controller
- usb usb2: Manufacturer: Linux 3.0.22-rt37+ ehci_hcd
- usb usb2: SerialNumber: ehci-omap.0
- usb usb2: usb_probe_device
- usb usb2: configuration #1 chosen from 1 choice
- usb usb2: adding 2-0:1.0 (config #1, interface 0)
- hub 2-0:1.0: usb_probe_interface
- hub 2-0:1.0: usb_probe_interface - got id
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 3 ports detected
- hub 2-0:1.0: standalone hub
- hub 2-0:1.0: individual port power switching
- hub 2-0:1.0: individual port over-current protection
- hub 2-0:1.0: power on to power good time: 20ms
- hub 2-0:1.0: local power source is good
- hub 2-0:1.0: enabling power on all ports
- drivers/usb/core/inode.c: creating file '001'
- ehci-omap ehci-omap.0: ...powerup ports...
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mousedev: PS/2 mouse device common for all mice
- twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
- twl_rtc twl_rtc: Power up reset detected.
- i2c /dev entries driver
- lirc_dev: IR Remote Control driver registered, major 250
- IR NEC protocol handler initialized
- IR RC5(x) protocol handler initialized
- IR RC6 protocol handler initialized
- IR JVC protocol handler initialized
- IR Sony protocol handler initialized
- IR RC5 (streamzap) protocol handler initialized
- IR LIRC bridge handler initialized
- Linux video capture interface: v2.00
- gspca: v2.13.0 registered
- usbcore: registered new interface driver uvcvideo
- USB Video Class driver (v1.1.0)
- Registered led device: overo:red:gpio21
- Registered led device: overo:blue:gpio22
- Registered led device: overo:blue:COM
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- TCP cubic registered
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- Registering the dns_resolver key type
- VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- ThumbEE CPU extension supported.
- fbcvt: 1280x720@60: CVT Name - .921M9-R
- hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000
- Console: switching to colour frame buffer device 160x45
- regulator_init_complete: VDAC: incomplete constraints, leaving on
- twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:07 UTC (946684807)
- omap_vout omap_vout: probed for an unknown device
- mmc0: host does not support reading read-only switch. assuming write-enable.
- mmc0: new SDHC card at address 1234
- mmcblk0: mmc0:1234 SA16G 14.8 GiB
- mmcblk0: p1 p2 p3
- Freeing init memory: 180K
- udev[88]: starting version 167
- aufs 3.0-20120109
- EXT3-fs: barriers not enabled
- EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
- kjournald starting. Commit interval 5 seconds
- aufs test_add:261:exe[208]: uid/gid/perm /ro 0/0/0755, 0/0/01777
- EXT3-fs: barriers not enabled
- kjournald starting. Commit interval 5 seconds
- EXT3-fs (mmcblk0p3): warning: mounting unchecked fs, running e2fsck is recommended
- EXT3-fs (mmcblk0p3): using internal journal
- EXT3-fs (mmcblk0p3): mounted filesystem with writeback data mode
- udev[317]: starting version 167
- smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xe0806000, IRQ: 336
- GPIO Event Monitor 0.1 Compiled: Mar 7 2012 at 13:51:38
- hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0004
- ehci-omap ehci-omap.0: GetStatus port:2 status 001803 0 ACK POWER sig=j CSC CONNECT
- hub 2-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
- hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
- ehci-omap ehci-omap.0: port 2 high speed
- ehci-omap ehci-omap.0: GetStatus port:2 status 001005 0 ACK POWER sig=se0 PE CONNECT
- usb 2-2: new high speed USB device number 2 using ehci-omap
- ehci-omap ehci-omap.0: port 2 high speed
- ehci-omap ehci-omap.0: GetStatus port:2 status 001005 0 ACK POWER sig=se0 PE CONNECT
- usb 2-2: default language 0x0409
- usb 2-2: udev 2, busnum 2, minor = 129
- usb 2-2: New USB device found, idVendor=1aa6, idProduct=0201
- usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- usb 2-2: Product: USB_DISK
- usb 2-2: SerialNumber: 000000020003781
- usb 2-2: usb_probe_device
- usb 2-2: configuration #1 chosen from 1 choice
- usb 2-2: adding 2-2:1.0 (config #1, interface 0)
- usb-storage 2-2:1.0: usb_probe_interface
- usb-storage 2-2:1.0: usb_probe_interface - got id
- scsi0 : usb-storage 2-2:1.0
- drivers/usb/core/inode.c: creating file '002'
- scsi 0:0:0:0: CD-ROM USB_DISK 2.00 PQ: 0 ANSI: 0
- scsi 0:0:0:1: Direct-Access USB_DISK 2.00 PQ: 0 ANSI: 0
- sd 0:0:0:1: [sda] 768512 512-byte logical blocks: (393 MB/375 MiB)
- sd 0:0:0:1: [sda] Write Protect is off
- sd 0:0:0:1: [sda] Mode Sense: 03 00 00 00
- sd 0:0:0:1: [sda] No Caching mode page present
- sd 0:0:0:1: [sda] Assuming drive cache: write through
- sd 0:0:0:1: [sda] No Caching mode page present
- sd 0:0:0:1: [sda] Assuming drive cache: write through
- sda: sda1
- sd 0:0:0:1: [sda] No Caching mode page present
- sd 0:0:0:1: [sda] Assuming drive cache: write through
- sd 0:0:0:1: [sda] Attached SCSI removable disk
- scsi 0:0:0:0: Attached scsi generic sg0 type 5
- sd 0:0:0:1: Attached scsi generic sg1 type 0
- sr0: scsi3-mmc drive: 0x/0x writer caddy
- cdrom: Uniform CD-ROM driver Revision: 3.20
- sr 0:0:0:0: Attached scsi CD-ROM sr0
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement