1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.03.03 12:23:50 =~=~=~=~=~=~=~=~=~=~=~=
  2.  
  3. NAND Boot
  4. Starting U-Boot ...
  5. [S] pressed, enable UART0
  6. [M] pressed, boot from sd card
  7.  
  8.  
  9. U-Boot 2010.06-dirty (Feb 27 2011 - 16:11:47)
  10.  
  11. Board: Qi LB60 (Ingenic XBurst Jz4740 SoC, Speed 336 MHz)
  12. DRAM: 32 MiB
  13. NAND: 2048 MiB
  14. [ 0.000000] Linux version 2.6.37.1 (bas@bas) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #4 PREEMPT Thu Mar 3 12:22:24 MSK 2011
  15. [ 0.000000] bootconsole [early0] enabled
  16. [ 0.000000] CPU revision is: 0ad0024f (Ingenic JZRISC)
  17. [ 0.000000] Determined physical RAM map:
  18. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  19. [ 0.000000] User-defined physical RAM map:
  20. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  21. [ 0.000000] Zone PFN ranges:
  22. [ 0.000000] Normal 0x00000000 -> 0x00002000
  23. [ 0.000000] Movable zone start PFN for each node
  24. [ 0.000000] early_node_map[1] active PFN ranges
  25. [ 0.000000] 0: 0x00000000 -> 0x00002000
  26. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 8128
  27. [ 0.000000] Kernel command line: mem=32M console=tty0 console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait
  28. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  29. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  30. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  31. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
  32. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
  33. [ 0.000000] Memory: 28448k/32768k available (2692k kernel code, 4320k reserved, 959k data, 148k init, 0k highmem)
  34. [ 0.000000] NR_IRQS:190
  35. [ 0.000000] Console: colour dummy device 80x25
  36. [ 0.000000] Linux version 2.6.37.1 (bas@bas) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #4 PREEMPT Thu Mar 3 12:22:24 MSK 2011
  37. [ 0.000000] bootconsole [early0] enabled
  38. [ 0.000000] CPU revision is: 0ad0024f (Ingenic JZRISC)
  39. [ 0.000000] Determined physical RAM map:
  40. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  41. [ 0.000000] User-defined physical RAM map:
  42. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  43. [ 0.000000] Zone PFN ranges:
  44. [ 0.000000] Normal 0x00000000 -> 0x00002000
  45. [ 0.000000] Movable zone start PFN for each node
  46. [ 0.000000] early_node_map[1] active PFN ranges
  47. [ 0.000000] 0: 0x00000000 -> 0x00002000
  48. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 8128
  49. [ 0.000000] Kernel command line: mem=32M console=tty0 console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait
  50. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  51. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  52. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  53. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
  54. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
  55. [ 0.000000] Memory: 28448k/32768k available (2692k kernel code, 4320k reserved, 959k data, 148k init, 0k highmem)
  56. [ 0.000000] NR_IRQS:190
  57. [ 0.000000] Console: colour dummy device 80x25
  58. [ 0.000000] console [tty0] enabled
  59. [ 0.010000] Calibrating delay loop... 335.05 BogoMIPS (lpj=1675264)
  60. [ 0.250000] pid_max: default: 32768 minimum: 301
  61. [ 0.260000] Mount-cache hash table entries: 512
  62. [ 0.280000] NET: Registered protocol family 16
  63. [ 0.300000] JZ4740 GPIO initalized
  64. [ 0.310000] Qi Hardware JZ4740 QI LB60 setup
  65. [ 0.370000] bio: create slab <bio-0> at 0
  66. [ 0.390000] Switching to clocksource jz4740-timer
  67. [ 0.510000] NET: Registered protocol family 2
  68. [ 0.520000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  69. [ 0.530000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  70. [ 0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  71. [ 0.550000] TCP: Hash tables configured (established 1024 bind 1024)
  72. [ 0.560000] TCP reno registered
  73. [ 0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  74. [ 0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  75. [ 0.590000] NET: Registered protocol family 1
  76. [ 0.610000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  77. [ 0.620000] msgmni has been set to 55
  78. [ 0.630000] io scheduler noop registered
  79. [ 0.640000] io scheduler deadline registered (default)
  80. [ 0.670000] Console: switching to colour frame buffer device 40x15
  81. [ 0.700000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  82. [ 0.710000] serial8250.0: ttyS0 at MMIO 0x10030000 (irq = 17) is a 16550
  83. [ 0.720000] console [ttyS0] enabled, bootconsole disabled
  84. [ 0.720000] console [ttyS0] enabled, bootconsole disabled
  85. [ 0.730000] serial8250.0: ttyS1 at MMIO 0x10031000 (irq = 16) is a 16550
  86. [ 0.750000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung )
  87. [ 0.760000] Scanning device for bad blocks
  88. [ 1.040000] Bad eraseblock 3890 at 0x00007997f000
  89. [ 1.070000] Creating 4 MTD partitions on "jz4740-nand":
  90. [ 1.080000] 0x000000000000-0x000000400000 : "NAND BOOT partition"
  91. [ 1.100000] 0x000000400000-0x000000800000 : "NAND KERNEL partition"
  92. [ 1.120000] 0x000000800000-0x000020800000 : "NAND ROOTFS partition"
  93. [ 1.140000] 0x000020800000-0x000080000000 : "NAND DATA partition"
  94. [ 1.160000] jz4740-nand jz4740-nand.0: Successfully registered JZ4740 NAND driver
  95. [ 1.200000] g_ether gadget: using random self ethernet address
  96. [ 1.210000] g_ether gadget: using random host ethernet address
  97. [ 1.220000] usb0: MAC fa:c0:80:10:83:64
  98. [ 1.230000] usb0: HOST MAC 0e:18:9d:01:fc:96
  99. [ 1.240000] g_ether gadget: controller 'jz4740-udc' not recognized; trying CDC Ethernet (ECM)
  100. [ 1.250000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
  101. [ 1.260000] g_ether gadget: g_ether ready
  102. [ 1.270000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
  103. [ 1.280000] input: matrix-keypad as /devices/platform/matrix-keypad/input/input1
  104. [ 1.290000] input: pwm-beeper as /devices/platform/pwm-beeper/input/input2
  105. [ 1.310000] jz4740-rtc jz4740-rtc: rtc core: registered jz4740-rtc as rtc0
  106. [ 1.330000] jz4740-mmc jz4740-mmc.0: JZ SD/MMC card driver registered
  107. [ 1.350000] TCP westwood registered
  108. [ 1.360000] NET: Registered protocol family 17
  109. [ 1.390000] jz4740-rtc jz4740-rtc: setting system clock to 1970-01-01 00:20:56 UTC (1256)
  110. [ 1.400000] Waiting for root device /dev/mmcblk0p1...
  111. [ 1.440000] mmc0: host does not support reading read-only switch. assuming write-enable.
  112. [ 1.450000] mmc0: new SD card at address aaaa
  113. [ 1.470000] mmcblk0: mmc0:aaaa SU256 241 MiB
  114. [ 1.490000] mmcblk0: p1 p2
  115. [ 1.520000] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
  116. [ 1.550000] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
  117. [ 1.580000] VFS: Mounted root (ext2 filesystem) on device 179:1.
  118. [ 1.600000] Freeing unused kernel memory: 148k freed
  119. - preinit -
  120. Press the [f] key and hit [enter] to enter failsafe mode
  121. - regular preinit -
  122. [ 6.620000] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
  123. - init -
  124.  
  125. Please press Enter to activate this console. [ 10.860000] asoc: jz4740-hifi <-> jz4740-i2s mapping ok
  126.  
  127.  
  128.  
  129. BusyBox v1.17.3 (2011-03-02 16:46:00 MSK) built-in shell (ash)
  130. Enter 'help' for a list of built-in commands.
  131.  
  132. _______ ________ __
  133. | |.-----.-----.-----.| | | |.----.| |_
  134. | - || _ | -__| || | | || _|| _|
  135. |_______|| __|_____|__|__||________||__| |____|
  136. |__| W I R E L E S S F R E E D O M
  137. ATTITUDE ADJUSTMENT (bleeding edge, r25820) ----------
  138. * 1/4 oz Vodka Pour all ingredents into mixing
  139. * 1/4 oz Gin tin with ice, strain into glass.
  140. * 1/4 oz Amaretto
  141. * 1/4 oz Triple sec
  142. * 1/4 oz Peach schnapps
  143. * 1/4 oz Sour mix
  144. * 1 splash Cranberry juice
  145. -----------------------------------------------------
  146. root@BenNanoNote:/# uname -a
  147. Linux BenNanoNote 2.6.37.1 #4 PREEMPT Thu Mar 3 12:22:24 MSK 2011 mips GNU/Linux
  148. root@BenNanoNote:/# kexec -l /bo
  149. root@BenNanoNote:/# kexec -l /boot/vm
  150. root@BenNanoNote:/# kexec -l /boot/vmlinux.elf
  151. root@BenNanoNote:/# kexec -e
  152. [ 34.130000] Starting new kernel
  153. [ 34.150000] image->start = 14370
  154. [ 34.160000] image-phys-to-virt->start = 80014370
  155. [ 34.170000] Will call new kernel at 80014370
  156. [ 34.170000] Bye ...
  157. [ 0.000000] Linux version 2.6.37.1 (bas@bas) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #4 PREEMPT Thu Mar 3 12:22:24 MSK 2011
  158. [ 0.000000] bootconsole [early0] enabled
  159. [ 0.000000] CPU revision is: 0ad0024f (Ingenic JZRISC)
  160. [ 0.000000] Determined physical RAM map:
  161. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  162. [ 0.000000] Zone PFN ranges:
  163. [ 0.000000] Normal 0x00000000 -> 0x00002000
  164. [ 0.000000] Movable zone start PFN for each node
  165. [ 0.000000] early_node_map[1] active PFN ranges
  166. [ 0.000000] 0: 0x00000000 -> 0x00002000
  167. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 8128
  168. [ 0.000000] Kernel command line:
  169. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  170. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  171. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  172. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
  173. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
  174. [ 0.000000] Memory: 28448k/32768k available (2692k kernel code, 4320k reserved, 959k data, 148k init, 0k highmem)
  175. [ 0.000000] NR_IRQS:190
  176. [ 0.000000] Console: colour dummy device 80x25
  177. [ 0.000000] console [tty0] enabled, bootconsole disabled