# dmesg
Linux version 2.6.22 (zhaoguang@sw1) (gcc version 4.2.3) #3 Fri Mar 11 09:02:10
1
CPU revision is: 00019749
Found a 16MB ST compatible serial flash
wombo_reset set to gpio 23
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 16384) 0 entries of 256 used
Zone PFN ranges:
Normal 0 -> 16384
HighMem 16384 -> 16384
early_node_map[1] active PFN ranges
0: 0 -> 16384
On node 0 totalpages: 16384
Normal zone: 0 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16384 pages, LIFO batch:3
HighMem zone: 0 pages used for memmap
Built 1 zonelists. Total pages: 16384
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5357 rev 1 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60292k/65536k available (2805k kernel code, 5180k reserved, 554k data, )
Calibrating delay loop... 249.03 BogoMIPS (lpj=1245184)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
gpio_init: power pulse time 7
Register DIAG LED in /proc/sys/diag_blink.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1766
Creating 4 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x00ff0000 : "linux"
0x001b9800-0x00ff0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-y
0x00ff0000-0x01000000 : "nvram"
u32 classifier
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
edward ====to register conntrack protocol helper for esp:
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
edward =======nf_nat_proto_esp_init
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
Warning: unable to open an initial console.
Failed to execute /init
ctmisc: module license 'unspecified' taints kernel.
Register /dev/ctmisc device, major:10 minor:255
Algorithmics/MIPS FPU Emulator v1.5
ctmisc_ioctl: cmd=0x11, buffer size=196
data_init(): base = 0xbc03ef00
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x26, buffer size=196
data_init(): base = 0xbc03fcdc
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x15, buffer size=196
data_init(): base = 0xbc03fe30
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x2c, buffer size=196
data_init(): base = 0xbc03fe20
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x2e, buffer size=196
data_init(): base = 0xbc03fe10
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x5e, buffer size=196
data_init(): base = 0xbc03fe00
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x17, buffer size=196
sflash_init: sflash type 0x100
sflash_init: sflash type 0x17
Flash Type: SFLASH 16384 kB
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x28, buffer size=196
data_init(): base = 0xbc03f6c0
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x2a, buffer size=196
data_init(): base = 0xbc03f600
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x38, buffer size=196
data_init(): base = 0xbc03f4c0
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x3a, buffer size=196
data_init(): base = 0xbc03f400
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x3c, buffer size=196
data_init(): base = 0xbc03f980
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x48, buffer size=196
data_init(): base = 0xbc03f2c0
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x4a, buffer size=196
data_init(): base = 0xbc03f200
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x4c, buffer size=196
data_init(): base = 0xbc03f8c0
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x58, buffer size=196
data_init(): base = 0xbc03f0c0
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x5a, buffer size=196
data_init(): base = 0xbc03f000
data_init(): location = [1], mydatas index = 1
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
ctmisc_ioctl: cmd=0x5c, buffer size=196
data_init(): base = 0xbc03f800
data_init(): location = [0], mydatas index = 0
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
ufsd: driver head (HEAD_A) LBD=OFF with ioctl loaded at c00cb000
NTFS read/write support included
Hfs+/HfsX read/write support included
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x200
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.127.2901 @VERS@
wl_module_init: wl_txq_thresh set to 0x200
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4347 802.11 Wireless Controller 5.60.127.2901 @VERSION_TYPE@
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
dev Has not parent!
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
dev Has not parent!
usb 1-2: new high speed USB device using ehci_hcd and address 2
Symbol usb_register_driver is being used by a non-GPL module, which will not bee
Please see the file Documentation/feature-removal-schedule.txt in the kernel so.
Symbol usb_deregister is being used by a non-GPL module, which will not be alloe
Please see the file Documentation/feature-removal-schedule.txt in the kernel so.
wl_module_init: rpcq_rxthresh set to 0x200
wl_module_init: wl_txq_thresh set to 0x200
usb 1-2: configuration #1 chosen from 1 choice
EHCI Fastpath: usb_dev 83961c00
EHCI Fastpath: bus 8063e400
EHCI Fastpath: Hub 8397ac00
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass device command in EHCI 8390
EHCI Fastpath: usb_dev 83961c00
EHCI Fastpath: bus 8063e400
EHCI Fastpath: Hub 8397ac00
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass callback command in EHCI cc
EHCI Fastpath: usb_dev 83961c00
EHCI Fastpath: bus 8063e400
EHCI Fastpath: Hub 8397ac00
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP 4
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 836b40ec QH a3f98100 dummy a3f3f060
EHCI Fastpath: usb_dev 83961c00
EHCI Fastpath: bus 8063e400
EHCI Fastpath: Hub 8397ac00
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP 2
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 836b40a4 QH a3f98180 dummy a3f3f120
EHCI Fastpath: EP in 18 EP in2 19 EP out 4
ehci_hcd 0000:00:04.1: dma_pool_free usbnet_qtd, a3f3f060/3f3f060 (bad dma)
bcm_rpc_up: waiting to be connected
bcm_rpc_buf_recv_mgn_high: Recvd:2 Version: 0x53c7fb5
State: 1 Session:0
bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x53c7fb5
bcm_rpc_buf_recv_mgn_high: Connected!
eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.60.127.2901 @VERSION_TYPE@
usbcore: registered new interface driver dbus_usbdev
[cbt_tcp_init]: init tcp module ..
[init]: tcp_init ok
[dns_init]: init dns module ..
[init]: dns_init ok
[pct_init]: init pct module ..
[init]: pct_init ok
[ssl_init]: init ssl module ..
[init]: ssl_init ok
[wp_proc_write]: --- Disable wireless warning page ---
[wp_unhook]: hook already unregistered
device vlan1 entered promiscuous mode
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
vlan1: add xxxxxx mcast address to master interface
vlan1: add xxxxxx mcast address to master interface
vlan1: add xxxxxx mcast address to master interface
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
[wp_proc_write]: --- Enable wireless warning page ---
[wp_hook]: Wireless warning page => Enable
####Set tcp option SMB_FAST
####Set tcp option SMB_FAST
[tblk_proc_write]: tblock_string=flush
[tblk_proc_write]: flush all tblk entries...
vlan2: Setting MAC address to xx xx xx xx xx xx.
vlan2: add xxxxxx mcast address to master interface
vlan2: add xxxxxx mcast address to master interface
vlan2: add xxxxxx mcast address to master interface
eth0: no IPv6 routers present
eth2: no IPv6 routers present
eth1: no IPv6 routers present
vlan1: no IPv6 routers present
br0: no IPv6 routers present
vlan2: no IPv6 routers present
rpc uptime 1 minutes
rpc uptime 2 minutes
rpc uptime 3 minutes
rpc uptime 4 minutes
rpc uptime 5 minutes
rpc uptime 6 minutes
rpc uptime 7 minutes
rpc uptime 8 minutes
rpc uptime 9 minutes
rpc uptime 10 minutes
rpc uptime 11 minutes
rpc uptime 12 minutes
rpc uptime 13 minutes
rpc uptime 14 minutes
rpc uptime 15 minutes
rpc uptime 16 minutes
rpc uptime 17 minutes
rpc uptime 18 minutes
rpc uptime 19 minutes
rpc uptime 20 minutes
rpc uptime 21 minutes
rpc uptime 22 minutes
rpc uptime 23 minutes
rpc uptime 24 minutes
rpc uptime 25 minutes
rpc uptime 26 minutes
rpc uptime 27 minutes
rpc uptime 28 minutes
rpc uptime 29 minutes
rpc uptime 30 minutes
rpc uptime 31 minutes
rpc uptime 32 minutes
rpc uptime 33 minutes
rpc uptime 34 minutes
rpc uptime 35 minutes
rpc uptime 36 minutes
rpc uptime 37 minutes
rpc uptime 38 minutes
rpc uptime 39 minutes
rpc uptime 40 minutes
rpc uptime 41 minutes
rpc uptime 42 minutes
rpc uptime 43 minutes
rpc uptime 44 minutes
rpc uptime 45 minutes
rpc uptime 46 minutes
rpc uptime 47 minutes
rpc uptime 48 minutes
rpc uptime 49 minutes
rpc uptime 50 minutes
rpc uptime 51 minutes
rpc uptime 52 minutes
rpc uptime 53 minutes
rpc uptime 54 minutes
rpc uptime 55 minutes
rpc uptime 56 minutes
rpc uptime 57 minutes
rpc uptime 58 minutes
rpc uptime 59 minutes
rpc uptime 60 minutes
rpc uptime 61 minutes
rpc uptime 62 minutes
rpc uptime 63 minutes
rpc uptime 64 minutes
rpc uptime 65 minutes
rpc uptime 66 minutes
rpc uptime 67 minutes
rpc uptime 68 minutes
rpc uptime 69 minutes
rpc uptime 70 minutes
rpc uptime 71 minutes
rpc uptime 72 minutes
rpc uptime 73 minutes
rpc uptime 74 minutes
rpc uptime 75 minutes
rpc uptime 76 minutes
rpc uptime 77 minutes
rpc uptime 78 minutes
rpc uptime 79 minutes
rpc uptime 80 minutes
SysRq : HELP : loglevel0-8 reBoot tErm Full kIll showMem Nice showPc show-all-t
rpc uptime 81 minutes
#