#!/bin/bash
# In order to use this iptables firewall script you
# must have iptables installed. You also must be using
# a 2.4.x series Kernel, with iptables suppport compiled
# into it, which is standard for most newer linux distributions.
#
# If you need help compiling iptables into your kernel, please
# see our kernel Compile/Upgrade Guide located at
# www.linuxhelp.net/guides/
#
# Once the script has been edited with all your relevant
# information (IP's Network Interfaces, etc..) simply
# make the script executable and run it as root.
#
# chmod 700 fw_rules.sh
# ./fw_rules.sh
#
# If you would like to see what rules are currently set, as
# root run iptables -L
#
# If you've messed up and need to bring down the firewall
# for whatever reason, run iptables -F
#
# If you would like to have the firewall automatically
# come up at boot time, add the path to the script to
# the bottom of your /etc/rc.d/rc.local file. For instance
# /root/bin/fw_rules.sh
#
# If you're not sure about something, check out the iptables
# man page by typing 'man iptables' (without the ''s) at the
# command prompt.
#
# This script is an enhanced/modified version of the
# iptables-script written by Davion
#
# If you have any questions, please come to us in #Linuxhelp.net
# on the DALnet IRC network. (www.linuxhelp.net/ircinfo.shtml)
# The location of the iptables binary on your system.
IPT="/sbin/iptables"
# The network interface you will be protecting. For ADSL/dialup users,
# ppp0 should be fine. If you are using a cable internet connection or
# are connected to a LAN, you will have to change this to "eth0".
#INT="ppp0"
## assuming 'eth0' is appropriate interface
INT="eth0"
# The following rules will clear out any existing firewall rules,
# and any chains that might have been created.
$IPT -F
$IPT -F INPUT
$IPT -F OUTPUT
$IPT -F FORWARD
$IPT -F -t mangle
$IPT -F -t nat
$IPT -X
# These will setup our policies.
$IPT -P INPUT DROP
$IPT -P OUTPUT ACCEPT
$IPT -P FORWARD ACCEPT
# The following line below enables IP forwarding and thus
# by extension, NAT. Turn this on if you're going to be doing NAT or IP masquerading.
## not needed if not acting as router
## #echo 1 > /proc/sys/net/ipv4/ip_forward
# Source NAT everything heading out the $INT (external)
# interface to be the given IP. If you have a dynamic IP
# address or a DHCP IP that changes semi-regularly, comment out
# the first line and uncomment the second line.
#
# Remember to change the ip address below to your static ip.
#
#$IPT -t nat -A POSTROUTING -o $INT -j SNAT --to 192.168.8.100
## not acting as router SNAT/MASQ not necessary
## #$IPT -t nat -A POSTROUTING -o $INT -j MASQUERADE
# This rule protects your forwarding rule.
## not acting as router
## #$IPT -A FORWARD -i $INT -m state --state NEW,INVALID -j DROP
# If you would like to forward specific ports to other machines
# on your home network, edit and uncomment the rules below. They are
# currently set up to forward port 25 & 53 (Mail & DNS) to 10.1.1.51.
# Anything incoming over your $INT through your gateway will
# be automatically redirected invisibly to port 25 & 53 on 10.1.1.51
# Mail Traffic
#$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 25 -j DNAT --to 10.1.1.51:25
# DNS Traffic
#$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 53 -j DNAT --to 10.1.1.51:53
#$IPT -t nat -A PREROUTING -i $INT -p udp --dport 53 -j DNAT --to 10.1.1.51:53
# SSH Traffic
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 22 -j DNAT --to 192.168.8.100
# VNC Traffic
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 5900 -j DNAT --to 192.168.8.100
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 5901 -j DNAT --to 192.168.8.100
# NetBios-Ns Name Service Traffic (Samba)
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 137 -j DNAT --to 192.168.8.100
## #$IPT -t nat -A PREROUTING -i $INT -p udp --dport 137 -j DNAT --to 192.168.8.100
# NetBios-Dgm Datagram Service Traffic (Samba)
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 138 -j DNAT --to 192.168.8.100
## #$IPT -t nat -A PREROUTING -i $INT -p udp --dport 138 -j DNAT --to 192.168.8.100
# NetBios-Ssn Session Service Traffic (Samba)
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 139 -j DNAT --to 192.168.8.100
## #$IPT -t nat -A PREROUTING -i $INT -p udp --dport 139 -j DNAT --to 192.168.8.100
# Microsoft-ds Domain Service Traffic (Samba)
## #$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 445 -j DNAT --to 192.168.8.100
## #$IPT -t nat -A PREROUTING -i $INT -p udp --dport 445 -j DNAT --to 192.168.8.100
# These two redirect a block of ports, in both udp and tcp.
#$IPT -t nat -A PREROUTING -i $INT -p tcp --dport 2300:2400 -j DNAT --to 10.1.1.50
#$IPT -t nat -A PREROUTING -i $INT -p udp --dport 2300:2400 -j DNAT --to 10.1.1.50
# Now, our SSH_WHITELIST chain.
## #$IPT -N SSH_WHITELIST
# Now, our firewall chain. We use the limit commands to
# cap the rate at which it alerts to 15 log messages per minute.
$IPT -N firewall
$IPT -A firewall -m limit --limit 15/minute -j LOG --log-prefix Firewall:
$IPT -A firewall -j DROP
# Now our dropwall chain, for the final catchall filter.
$IPT -N dropwall
$IPT -A dropwall -m limit --limit 15/minute -j LOG --log-prefix Dropwall:
$IPT -A dropwall -j DROP
# Our "Hey, them's some bad tcp flags!" chain.
$IPT -N badflags
$IPT -A badflags -m limit --limit 15/minute -j LOG --log-prefix Badflags:
$IPT -A badflags -j DROP
# And our silent logging chain.
## #$IPT -N silent
## #$IPT -A silent -j DROP
# This rule will accept connections from local machines. If you have
# a home network, enter in the IP's of the machines on the
# network below.
$IPT -A INPUT -i lo -j ACCEPT
## consider that 'wrt54gl' is also on this network
$IPT -A INPUT -s 192.168.8.0/24 -d 0/0 -p all -j ACCEPT
#$IPT -A INPUT -s 10.1.1.51 -d 0/0 -p all -j ACCEPT
#$IPT -A INPUT -s 10.1.1.52 -d 0/0 -p all -j ACCEPT
# Drop these nasty packets! These are all TCP flag
# combinations that should never, ever occur in the
# wild. All of these are illegal combinations that
# are used to attack a box in various ways, so we
# just drop them and log them here.
$IPT -A INPUT -p tcp --tcp-flags ALL FIN,URG,PSH -j badflags
$IPT -A INPUT -p tcp --tcp-flags ALL ALL -j badflags
$IPT -A INPUT -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j badflags
$IPT -A INPUT -p tcp --tcp-flags ALL NONE -j badflags
#$IPT -A INPUT -p tcp --tcp-flags ALL SYN,RST SYN,RST -j badflags #Commented out because my box tells me SYN,RST are invalid commands
#$IPT -A INPUT -p tcp --tcp-flags ALL SYN,FIN SYN,FIN -j badflags #Commented out because my box tells me SYN,FIN are invalid commands
#NOT SURE HERE I want pinging to return no response as if the box didn't exist
# Drop icmp, but only after letting certain types through.
## unless you forward icmp from 'wrt54gl' to 'server', \
## 'wrt54gl' is handling public icmp requests negating this for all but \
## local network
$IPT -A INPUT -p icmp --icmp-type 0 -j ACCEPT
$IPT -A INPUT -p icmp --icmp-type 3 -j ACCEPT
$IPT -A INPUT -p icmp --icmp-type 11 -j ACCEPT
$IPT -A INPUT -p icmp --icmp-type 8 -m limit --limit 1/second -j ACCEPT
$IPT -A INPUT -p icmp -j firewall
# If you would like to open up port 22 (SSH Access) to various IP's
# simply edit the IP's below and uncomment the line. If you wish to
# enable SSH access from anywhere, uncomment the second line only.
#$IPT -A INPUT -i $INT -s 10.1.1.1 -d 0/0 -p tcp --dport 22 -j ACCEPT
#$IPT -A INPUT -i $INT -s 0/0 -d 0/0 -p tcp --dport 22 -j ACCEPT
## #$IPT -A SSH_WHITELIST -s "my work IP without quotes" -m recent --remove --name SSH -j ACCEPT
## #$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --set --name SSH
## #$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -j SSH_WHITELIST
## #$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --update --seconds 60 --hitcount 4 --rttl --name SSH -j ULOG --ulog-prefix SSH_BRUTE_FORCE
## #$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --update --seconds 60 --hitcount 4 --rttl --name SSH -j DROP
## # #$IPT -A INPUT -s BAD_GUY_IP -j DROP
##
## whitelist known (?trusted?) network block
## local network is already addressed above in 'global' localnet ACCEPT
## example for completeness
$IPT -A INPUT -s 192.168.8.0/24 -p tcp --dport 22 \
-m state --state NEW -j ACCEPT
## change this to 'work' public network block
## as written, it _will_ fail because it is not a valid IP
$IPT -A INPUT -s 123.456.12.0/28 -p tcp --dport 22 \
-m state --state NEW -j ACCEPT
## limit scanned brute-force/dictionary login attempts
$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent \
--name NEW_SSH_ATTEMPT --update --seconds 60 --hitcount 2 \
-j LOG --log-prefix " NEW_SSH_ATTEMPT DROP "
$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent \
--name NEW_SSH_ATTEMPT --update --seconds 60 --hitcount 2 -j DROP
$IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent \
--name NEW_SSH_ATTEMPT --set -j ACCEPT
# Open Samba for Local Computers
$IPT -A INPUT -i $INT -s 0/0 -d 0/0 -p udp --dport 137:139 -j ACCEPT
$IPT -A INPUT -i $INT -s 0/0 -d 0/0 -p udp --dport 445 -j ACCEPT
# If you are running a web server, uncomment the next line to open
# up port 80 on your machine.
#$IPT -A INPUT -i $INT -s 0/0 -d 0/0 -p tcp --dport 80 -j ACCEPT
# Lets do some basic state-matching. This allows us
# to accept related and established connections, so
# client-side things like ftp work properly, for example.
## ideally this would be fairly early on in the chain since it should \
## match most often
$IPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
# Uncomment to drop port 137 netbiso packets silently.
# We don't like that netbios stuff, and it's way too
# spammy with windows machines on the network.
#$IPT -A INPUT -p udp --sport 137 --dport 137 -j silent
# Our final trap. Everything on INPUT goes to the dropwall
# so we don't get silent drops.
$IPT -A INPUT -j dropwall