1. root@overo:~$ dmesg
  2. Initializing cgroup subsys cpuset
  3. Initializing cgroup subsys cpu
  4. Linux version 3.2.58-custom (vin@vin-virtual-linux) (gcc version 4.8.2 (GCC) ) #1 PREEMPT Sun Jun 1 03:52:59 BST 2014
  5. CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c53c7d
  6. CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  7. Machine: Gumstix Overo
  8. Reserving 12582912 bytes SDRAM for VRAM
  9. Memory policy: ECC disabled, Data cache writeback
  10. On node 0 totalpages: 35584
  11. free_area_init_node: node 0, pgdat c06b99f0, node_mem_map c0751000
  12. Normal zone: 448 pages used for memmap
  13. Normal zone: 0 pages reserved
  14. Normal zone: 35136 pages, LIFO batch:7
  15. OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz )
  16. Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
  17. pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  18. pcpu-alloc: [0] 0
  19. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 35136
  20. Kernel command line: console=ttyO2,115200n8 mem=55M@0x80000000 mem=96M@0x88000000 i2c_bus=3,100 mpurate=500 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
  21. PID hash table entries: 1024 (order: 0, 4096 bytes)
  22. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  23. Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  24. allocated 917504 bytes of page_cgroup
  25. please try 'cgroup_disable=memory' option if you don't want memory cgroups
  26. Memory: 55MB 84MB = 139MB total
  27. Memory: 132492k/132492k available, 22132k reserved, 0K highmem
  28. Virtual kernel memory layout:
  29. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  30. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  31. vmalloc : 0xce800000 - 0xf8000000 ( 664 MB)
  32. lowmem : 0xc0000000 - 0xce000000 ( 224 MB)
  33. pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  34. modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  35. .text : 0xc0008000 - 0xc0633464 (6318 kB)
  36. .init : 0xc0634000 - 0xc0669000 ( 212 kB)
  37. .data : 0xc066a000 - 0xc06c3ab8 ( 359 kB)
  38. .bss : 0xc06c3adc - 0xc07507b0 ( 564 kB)
  39. NR_IRQS:410
  40. IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
  41. Total of 96 interrupts on 1 active controller
  42. OMAP clockevent source: GPTIMER1 at 32768 Hz
  43. sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
  44. Console: colour dummy device 80x30
  45. Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
  46. pid_max: default: 32768 minimum: 301
  47. Mount-cache hash table entries: 512
  48. Initializing cgroup subsys debug
  49. Initializing cgroup subsys cpuacct
  50. Initializing cgroup subsys memory
  51. Initializing cgroup subsys devices
  52. Initializing cgroup subsys freezer
  53. Initializing cgroup subsys perf_event
  54. CPU: Testing write buffer coherency: ok
  55. devtmpfs: initialized
  56. print_constraints: dummy:
  57. NET: Registered protocol family 16
  58. GPMC revision 5.0
  59. OMAP GPIO hardware version 2.5
  60. omap_mux_init: Add partition: #1: core, flags: 0
  61. Reprogramming SDRC clock to 332000000 Hz
  62. dpll3_m2_clk rate change failed: -22
  63. Found NAND on CS0
  64. Registering NAND on CS0
  65. platform iva.0: Enabled OPP corresponding to 720MHz
  66. hw-breakpoint: debug architecture 0x4 unsupported.
  67. omap-mcbsp.2: alias fck already exists
  68. omap-mcbsp.3: alias fck already exists
  69. Calibrating delay loop (skipped) already calibrated this CPU
  70. Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
  71. OMAP DMA hardware revision 4.0
  72. bio: create slab <bio-0> at 0
  73. machine_constraints_voltage: vads7846: override min_uV, 1 -> 3300000
  74. machine_constraints_voltage: vads7846: override max_uV, 2147483647 -> 3300000
  75. print_constraints: vads7846: 3300 mV
  76. reg-fixed-voltage reg-fixed-voltage.1: vads7846 supplying 3300000uV
  77. SCSI subsystem initialized
  78. usbcore: registered new interface driver usbfs
  79. usbcore: registered new interface driver hub
  80. usbcore: registered new device driver usb
  81. omap_i2c omap_i2c.1: bus 1 rev1.3.12 at 2600 kHz
  82. twl4030: PIH (irq 7) chaining IRQs 368..375
  83. twl4030: power (irq 373) chaining IRQs 376..383
  84. twl4030: gpio (irq 368) chaining IRQs 384..401
  85. machine_constraints_voltage: VUSB1V5: override min_uV, 1 -> 1500000
  86. machine_constraints_voltage: VUSB1V5: override max_uV, 2147483647 -> 1500000
  87. print_constraints: VUSB1V5: 1500 mV normal standby
  88. machine_constraints_voltage: VUSB1V8: override min_uV, 1 -> 1800000
  89. machine_constraints_voltage: VUSB1V8: override max_uV, 2147483647 -> 1800000
  90. print_constraints: VUSB1V8: 1800 mV normal standby
  91. machine_constraints_voltage: VUSB3V1: override min_uV, 1 -> 3100000
  92. machine_constraints_voltage: VUSB3V1: override max_uV, 2147483647 -> 3100000
  93. print_constraints: VUSB3V1: 3100 mV normal standby
  94. twl4030_usb twl4030_usb: HW_CONDITIONS 0x10/16; link 0
  95. twl4030_usb twl4030_usb: Initialized TWL4030 USB module
  96. print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby
  97. print_constraints: VDAC: 1800 mV normal standby
  98. print_constraints: VDVI: 1800 mV normal standby
  99. omap_i2c omap_i2c.3: bus 3 rev1.3.12 at 100 kHz
  100. omap-iommu omap-iommu.0: isp registered
  101. Advanced Linux Sound Architecture Driver Version 1.0.24.
  102. Switching to clocksource 32k_counter
  103. musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
  104. twl4030_usb twl4030_usb: twl4030_phy_resume
  105. musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
  106. musb-hdrc: MHDRC RTL version 1.400
  107. musb-hdrc: setup fifo_mode 4
  108. musb-hdrc: 28/31 max ep, 16384/16384 memory
  109. musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
  110. NET: Registered protocol family 2
  111. IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  112. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  113. TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
  114. TCP: Hash tables configured (established 8192 bind 8192)
  115. TCP reno registered
  116. UDP hash table entries: 256 (order: 0, 4096 bytes)
  117. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  118. NET: Registered protocol family 1
  119. RPC: Registered named UNIX socket transport module.
  120. RPC: Registered udp transport module.
  121. RPC: Registered tcp transport module.
  122. RPC: Registered tcp NFSv4.1 backchannel transport module.
  123. platform iva.0: Enabled OPP corresponding to 720MHz
  124. audit: initializing netlink socket (disabled)
  125. type=2000 audit(0.148:1): initialized
  126. VFS: Disk quotas dquot_6.5.2
  127. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  128. Registering unionfs 2.5.10 (for 3.1.0-rc4)
  129. JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  130. fuse init (API version 7.17)
  131. msgmni has been set to 258
  132. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  133. io scheduler noop registered
  134. io scheduler deadline registered (default)
  135. OMAP DSS rev 2.0
  136. omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
  137. omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
  138. omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
  139. console [ttyO2] enabled
  140. brd: module loaded
  141. loop: module loaded
  142. twl4030_madc twl4030_madc: clk disabled, enabling
  143. omap2-nand driver initializing
  144. ONFI flash detected
  145. NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
  146. Creating 5 MTD partitions on "omap2-nand.0":
  147. 0x000000000000-0x000000080000 : "xloader"
  148. 0x000000080000-0x000000240000 : "uboot"
  149. 0x000000240000-0x000000280000 : "uboot environment"
  150. 0x000000280000-0x000000680000 : "linux"
  151. 0x000000680000-0x000020000000 : "rootfs"
  152. smsc911x: Driver version 2008-10-21
  153. smsc911x-mdio: probed
  154. smsc911x smsc911x.0: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
  155. smsc911x smsc911x.0: eth0: MAC Address: 00:af:c1:00:03:02
  156. smsc911x: Driver version 2008-10-21
  157. usbcore: registered new interface driver kaweth
  158. usbcore: registered new interface driver asix
  159. usbcore: registered new interface driver cdc_ether
  160. cdc_ncm: 04-Aug-2011
  161. usbcore: registered new interface driver cdc_ncm
  162. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  163. ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
  164. ehci-omap ehci-omap.0: failed to get ehci port1 regulator
  165. ehci-omap ehci-omap.0: phy reset operation timed out
  166. ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
  167. ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
  168. ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
  169. /home/vin/yocto/build/tmp/work/overo-poky-linux-gnueabi/linux-gumstix/3.2-r0/git/drivers/usb/core/inode.c: creating file 'devices'
  170. /home/vin/yocto/build/tmp/work/overo-poky-linux-gnueabi/linux-gumstix/3.2-r0/git/drivers/usb/core/inode.c: creating file '001'
  171. ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
  172. ehci-omap ehci-omap.0: park 0
  173. ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
  174. ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
  175. ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
  176. ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
  177. usb usb1: default language 0x0409
  178. usb usb1: udev 1, busnum 1, minor = 0
  179. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  180. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  181. usb usb1: Product: OMAP-EHCI Host Controller
  182. usb usb1: Manufacturer: Linux 3.2.58-custom ehci_hcd
  183. usb usb1: SerialNumber: ehci-omap.0
  184. usb usb1: usb_probe_device
  185. usb usb1: configuration #1 chosen from 1 choice
  186. usb usb1: adding 1-0:1.0 (config #1, interface 0)
  187. hub 1-0:1.0: usb_probe_interface
  188. hub 1-0:1.0: usb_probe_interface - got id
  189. hub 1-0:1.0: USB hub found
  190. hub 1-0:1.0: 3 ports detected
  191. hub 1-0:1.0: standalone hub
  192. hub 1-0:1.0: individual port power switching
  193. hub 1-0:1.0: individual port over-current protection
  194. hub 1-0:1.0: power on to power good time: 20ms
  195. hub 1-0:1.0: local power source is good
  196. hub 1-0:1.0: enabling power on all ports
  197. /home/vin/yocto/build/tmp/work/overo-poky-linux-gnueabi/linux-gumstix/3.2-r0/git/drivers/usb/core/inode.c: creating file '001'
  198. ehci-omap ehci-omap.0: ...powerup ports...
  199. Initializing USB Mass Storage driver...
  200. usbcore: registered new interface driver usb-storage
  201. USB Mass Storage support registered.
  202. mousedev: PS/2 mouse device common for all mice
  203. twl_rtc twl_rtc: Power up reset detected.
  204. twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
  205. i2c /dev entries driver
  206. cpuidle: using governor ladder
  207. cpuidle: using governor menu
  208. hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
  209. Registered led device: overo:red:gpio21
  210. Registered led device: overo:blue:gpio22
  211. Registered led device: overo:blue:COM
  212. usbcore: registered new interface driver usbhid
  213. usbhid: USB HID core driver
  214. usbcore: registered new interface driver snd-usb-audio
  215. overo SoC init
  216. asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
  217. ALSA device list:
  218. #0: overo
  219. oprofile: hardware counters not available
  220. oprofile: using timer interrupt.
  221. TCP cubic registered
  222. NET: Registered protocol family 17
  223. NET: Registered protocol family 15
  224. Registering the dns_resolver key type
  225. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
  226. ThumbEE CPU extension supported.
  227. sr_init: No PMIC hook to init smartreflex
  228. smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
  229. smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
  230. clock: disabling unused clocks to save power
  231. registered taskstats version 1
  232. fbcvt: 1024x768@60: CVT Name - .786M3-R
  233. Console: switching to colour frame buffer device 128x48
  234. regulator_init_complete: VDAC: incomplete constraints, leaving on
  235. regulator_init_complete: vads7846: incomplete constraints, leaving on
  236. twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:10 UTC (946684810)
  237. Waiting for root device /dev/mmcblk0p2...
  238. mmc0: host does not support reading read-only switch. assuming write-enable.
  239. mmc0: new high speed SDHC card at address 59b4
  240. mmcblk0: mmc0:59b4 00000 3.67 GiB
  241. mmcblk0: p1 p2
  242. kjournald starting. Commit interval 5 seconds
  243. EXT3-fs (mmcblk0p2): using internal journal
  244. EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
  245. VFS: Mounted root (ext3 filesystem) on device 179:2.
  246. devtmpfs: mounted
  247. Freeing init memory: 212K
  248. systemd[1]: systemd 211 running in system mode. (+PAM +LIBWRAP -AUDIT -SELINUX +IMA +SYSVINIT -LIBCRYPTSETUP -GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
  249. systemd[1]: Detected architecture 'arm'.
  250. NET: Registered protocol family 10
  251. systemd[1]: Inserted module 'ipv6'
  252. systemd[1]: Set hostname to <overo>.
  253. systemd[1]: [/etc/systemd/system/network@.service:1] Assignment outside of section. Ignoring.
  254. systemd[1]: [/etc/systemd/system/network@.service:2] Assignment outside of section. Ignoring.
  255. systemd[1]: [/etc/systemd/system/network@.service:3] Assignment outside of section. Ignoring.
  256. systemd[1]: [/etc/systemd/system/network@.service:4] Assignment outside of section. Ignoring.
  257. systemd[1]: [/etc/systemd/system/network@.service:5] Assignment outside of section. Ignoring.
  258. systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
  259. systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  260. systemd[1]: Expecting device dev-ttyGS0.device...
  261. systemd[1]: Expecting device dev-ttyO2.device...
  262. systemd[1]: Starting Remote File Systems.
  263. systemd[1]: Reached target Remote File Systems.
  264. systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
  265. systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
  266. systemd[1]: Starting Paths.
  267. systemd[1]: Reached target Paths.
  268. systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
  269. systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  270. systemd[1]: Starting Swap.
  271. systemd[1]: Reached target Swap.
  272. systemd[1]: Starting Root Slice.
  273. systemd[1]: Created slice Root Slice.
  274. systemd[1]: Starting Journal Socket.
  275. systemd[1]: Listening on Journal Socket.
  276. systemd[1]: Starting Delayed Shutdown Socket.
  277. systemd[1]: Listening on Delayed Shutdown Socket.
  278. systemd[1]: Starting udev Kernel Socket.
  279. systemd[1]: Listening on udev Kernel Socket.
  280. systemd[1]: Starting udev Control Socket.
  281. systemd[1]: Listening on udev Control Socket.
  282. systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
  283. systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
  284. systemd[1]: Starting Syslog Socket.
  285. hub 1-0:1.0: hub_suspend
  286. usb usb1: bus auto-suspend, wakeup 1
  287. ehci-omap ehci-omap.0: suspend root hub
  288. systemd[1]: Listening on Syslog Socket.
  289. systemd[1]: Starting User and Session Slice.
  290. systemd[1]: Created slice User and Session Slice.
  291. systemd[1]: Starting System Slice.
  292. systemd[1]: Created slice System Slice.
  293. systemd[1]: Started Set Up Additional Binary Formats.
  294. systemd[1]: Mounting Debug File System...
  295. systemd[1]: Starting Journal Service...
  296. systemd[1]: Started Journal Service.
  297. systemd-udevd[87]: starting version 211
  298. systemd-journald[65]: Received request to flush runtime journal from PID 1
  299. ads7846 spi1.0: touchscreen, irq 274
  300. ads7846 spi1.0: no device detected, test read result was 0x00000000
  301. smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce816000, IRQ: 336
  302. eth0: IPv6 duplicate address fe80::2af:c1ff:fe00:302 detected!