Marvell>> print
bootdelay=3
baudrate=115200
x_bootcmd_ethernet=ping 192.168.2.1
x_bootcmd_usb=usb start
x_bootcmd_kernel=fatload usb 0 0x6400000 uImage
x_bootargs=console=ttyS0,115200
ethact=egiga0
ethaddr=F0:AD:4E:00:84:D7
eth1addr=F0:AD:4E:00:84:D8
bootcmd_sdb=setenv bootargs console=ttyS0,115200 root=/dev/sdb2 panic=10 rootwait; usb start; run boot_sdb;
boot_sdb=fatload usb 1 0x6400000 uImage; bootm 0x6400000;
bootcmd_eth=setenv ethact egiga0; ${x_bootcmd_ethernet}; setenv ethact egiga1; ${x_bootcmd_ethernet}
clear_kernel_in_mem=echo Purging kernel in memory; mw 0x6400000 0x0 0x300000
boot_sdb_dng=fatload usb 2 0x6400000 uImage; bootm 0x6400000;
x_bootargs_root_orig=root=/dev/sda2 rootdelay=10
x_bootargs_root=root/dev/sdc2 rootdelay=20
boot_sdc=fatload usb 2 0x6400000 uimage; bootm 0x6400000;
bootargs=console=ttyS0,115200 root=/dev/sdc2 panic=10 rootwait
boot_usb0=fatload usb 0 0x6400000 uimage; bootm 0x6400000;
bootcmd_sdc=setenv bootargs console=ttyS0,115200 root=/dev/sdd2 panic=10 rootwait; usb start; run boot_usb0;
stdin=serial
stdout=serial
stderr=serial
bootcmd_sda=setenv bootargs console=ttyS0,115200 root=/dev/sda2 panic=10 rootwait; usb start; run boot_usb0;
bootcmd=run clear_kernel_in_mem; run bootcmd_sda;
Environment size: 1222/4092 bytes
Marvell>> saveenv
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
Marvell>> reset
resetting ...
U-Boot 2011.06-02334-g8f495d9-dirty (Mar 28 2011 - 05:21:06)
Marvell-DreamPlug
SoC: Kirkwood 88F6281_A0
DRAM: 512 MiB
SF: Detected MX25L1606 with page size 256, total 1 MiB
In: serial
Out: serial
Err: serial
Net: egiga0, egiga1
88E1121 Initialized on egiga0
88E1121 Initialized on egiga1
Hit any key to stop autoboot: 0
Purging kernel in memory
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 02 3A 00
2 Storage Device(s) found
reading uimage
2712400 bytes read
## Booting kernel from Legacy Image at 06400000 ...
Image Name: Linux-2.6.33.6
Created: 2011-02-08 8:18:48 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2712336 Bytes = 2.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.33.6 (root@localhost.localdomain) (gcc version 4.2.1) #1 PREEMPT Tue Feb 8 03:18:41 EST 2011
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell GuruPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/sda2 panic=10 rootwait
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513408KB available (4832K code, 862K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: 00
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4012, nTxLock = 32102
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
No NAND device found.
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address f0:ad:4e:00:84:d7
net eth1: port 0 with MAC address f0:ad:4e:00:84:d8
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: guruplug:red:health
Registered led device: guruplug:green:health
Registered led device: guruplug:red:wmode
Registered led device: guruplug:green:wmode
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mmc0: new high speed SDIO card at address 0001
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2012-10-11 00:20:12 UTC (1349914812)
Waiting for root device /dev/sda2...
usb 1-1: new high speed USB device using orion-ehci and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new high speed USB device using orion-ehci and address 3
scsi0 : usb-storage 1-1.1:1.0
usb 1-1.4: new full speed USB device using orion-ehci and address 4
input: C-Media USB Headphone Set as /devices/platform/orion-ehci.0/usb1/1-1/1-1.4/1-1.4:1.3/input/input0
generic-usb 0003:0D8C:000C.0001: input: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-orion-ehci.0-1.4/input3
scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 3842048 512-byte logical blocks: (1.96 GB/1.83 GiB)
sd 0:0:0:1: Attached scsi generic sg1 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:1: [sdb] Attached SCSI removable disk
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sda: p2 size 3653412 exceeds device capacity, limited to end of disk
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
EXT3-fs (sda2): warning: mounting fs with errors, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda2): using internal journal
EXT3-fs (sda2): recovery complete
EXT3-fs (sda2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 8:2.
Freeing init memory: 140K
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 1
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata1: SATA link down (SStatus 0 SControl F300)
uap_probe: vendor=0x02DF device=0x9104 class=0 function=1
uap_sdio mmc0:0001:1: firmware: requesting mrvl/helper_sd.bin
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
uap_sdio mmc0:0001:1: firmware: requesting mrvl/sd8688_ap.bin
UAP FW is active
usbcore: registered new interface driver snd-usb-audio
Bluetooth: vendor=0x2df, device=0x9105, class=255, fn=2
sd 0:0:0:0: [sda] Media Changed
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0x6 [current]
sd 0:0:0:0: [sda] ASC=0x28 ASCQ=0x0
sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 18 47 12 00 00 60 00
end_request: I/O error, dev sda, sector 1591058
Aborting journal on device sda2.
EXT3-fs (sda2): error: ext3_journal_start_sb: Detected aborted journal
EXT3-fs (sda2): error: remounting filesystem read-only
sd 0:0:0:0: [sda] Assuming drive cache: write through
done.
sd 0:0:0:0: [sda] Media Changed
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0x6 [current]
sd 0:0:0:0: [sda] ASC=0x28 ASCQ=0x0
sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 18 47 5a 00 00 08 00
end_request: I/O error, dev sda, sector 1591130
/lib/init/vars.sh: line 18: 1583 Bus error egrep -qw 'quiet' /proc/cmdline
/etc/rcS.d/S05keymap.sh: /etc/rcS.d/S05keymap.sh: Input/output error
/etc/rcS.d/S08hwclockfirst.sh: /etc/rcS.d/S08hwclockfirst.sh: Input/output error
/etc/rcS.d/S10checkroot.sh: /etc/rcS.d/S10checkroot.sh: Input/output error
/etc/rcS.d/S11hwclock.sh: /etc/rEXT3-fs error (device sda2): ext3_get_inode_loc: cS.d/S11hwclock.unable to read inode block - inode=24662, block=98430sh: Input/output
error
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=24661, block=98430
/etc/init.d/rc: line 221: /etc/rcS.d/S20module-init-tools: Input/output error
/etc/rcS.d/S30checkfs.sh: /etc/rcS.d/S30checkfs.sh: Input/output error
/etc/init.d/rc: line 221EXT3-fs error (device sda2): ext3_get_inode_loc: : /etc/rcS.d/S30unable to read inode block - inode=24665, block=98430procps: Input/ou
tput error
/etc/rcS.d/S36mountall-bootclean.sh: /etc/rcS.d/S36mountall-bootclean.sh: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S36udev-mtab: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S37mountoverflowtmp: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S38pppd-dns: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S39ifupdown: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S40networking: Input/output error
/etc/init.d/rc: line 221: /etc/rcS.d/S43portmap: Input/output error
/etc/rcS.d/S45mountnfs.sh: /etc/EXT3-fs error (device sda2): ext3_get_inode_loc: rcS.d/S45mountnfunable to read inode block - inode=24668, block=98430s.sh: Input/outp
ut error
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=25369, block=98474
Setting up ALSA...done.
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=24671, block=98430
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=24669, block=98430
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=24666, block=98430
/etc/init.d/rc: line 221: /etc/rcS.d/S75sudo: Input/output error
INIT: Entering runlevel: 2/etc/rcS.d/S99stop-bootlogd-single: In
EXT3-fs error (device sda2): ext3_get_inode_loc: unable to read inode block - inode=24974, block=98449
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: Id "4" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "T0" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "1" respawning too fast: disabled for 5 minutes
INIT: Id "2" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "5" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: Id "6" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel