API tools faq
paste
Advertisement
Guest User

broly dd-wrt 4.9. wlan cuz drivers but finally built right!

a guest
Mar 21st, 2017
244
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
Bash 10.10 KB | None | 0 0
raw download clone embed print report
  1. CFE for Foxconn Router R7000 version: v1.0.22
  2. Build Date: Wed Mar 19 11:14:20 CST 2014
  3. Init Arena
  4. Init Devs.
  5. Boot up from NAND flash...
  6. Bootcode Boot partition size = 524288(0x80000)
  7. DDR Clock: 800 MHz
  8. Info: DDR frequency set from clkfreq=1000,*800*
  9. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.15.1 (r407936)
  10. et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.15.1 (r407936)
  11. CPU type 0x0: 1000MHz
  12. Tot mem: 262144 KBytes
  13.  
  14. Committing NVRAM...done
  15. Device eth0:  hwaddr A0-63-91-41-72-2F, ipaddr 192.168.1.1, mask 255.255.255.0
  16.         gateway not set, nameserver not set
  17. Loader:raw Filesys:tftp Dev:eth0 File:192.168.1.2:vmlinuz Options:(null)
  18. Loading: Failed.
  19. Could not load 192.168.1.2:vmlinuz: Timeout occured
  20. Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
  21. Loading: ... 1680592 bytes read
  22. Entry at 0x00008000
  23. Closing network.
  24. Starting program at 0x00008000
  25. Uncompressing Linux... done, booting the kernel.
  26. ** 45 printk messages dropped ** 2 cores has been found
  27. Setting up static identity map for 0x8600 - 0x8634
  28. L2C: platform provided aux values permit register corruption.
  29. L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x7a530000
  30. L2C-310 erratum 769419 enabled
  31. L2C-310 enabling early BRESP for Cortex-A9
  32. L2C-310 full line of zeros enabled for Cortex-A9
  33. L2C-310 dynamic clock gating enabled, standby mode enabled
  34. L2C-310 cache controller enabled, 16 ways, 256 kB
  35. L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x4e530001
  36. CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  37. Brought up 2 CPUs
  38. SMP: Total of 2 processors activated (3981.31 BogoMIPS).
  39. VFP support v0.3: not present
  40. clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  41. futex hash table entries: 512 (order: 3, 32768 bytes)
  42. NET: Registered protocol family 16
  43. DMA: preallocated 256 KiB pool for atomic coherent allocations
  44. coherence_win_size = 10000000
  45. coherence_flag = FFFFFFF8
  46. ddr_phys_offset_va =FFFFFFFF
  47. ddr_phys_offset2_va =A8000000
  48. Found a AMD NAND flash:
  49. Total size:  128MB
  50. Block size:  128KB
  51. Page Size:   2048B
  52. OOB Size:    64B
  53. Sector size: 512B
  54. Spare size:  16B
  55. ECC level:   8 (8-bit)
  56. Device ID: 0x 1 0xf1 0x80 0x1d 0x 1 0xf1
  57. found nand nvram at 80000
  58. CCA UART Clock Config: Sel=1 Ovr=1 Div=48
  59. CCA UART Clock rate 125000000Hz CCB UART Clock rate 125000000Hz
  60. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 32
  61. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 36
  62. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 40
  63. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 42
  64. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 44
  65. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x40201000, IAS 48
  66. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 32
  67. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 36
  68. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 40
  69. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 42
  70. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 44
  71. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x02004000, IAS 48
  72. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 32
  73. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 36
  74. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 40
  75. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 42
  76. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 44
  77. arm-lpae io-pgtable: selftest: pgsize_bitmap 0x20010000, IAS 48
  78. arm-lpae io-pgtable: selftest: completed with 18 PASS 0 FAIL
  79. clocksource: Switched to clocksource mpcore_gtimer
  80. NET: Registered protocol family 2
  81. TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  82. TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
  83. TCP: Hash tables configured (established 1024 bind 1024)
  84. UDP hash table entries: 256 (order: 1, 8192 bytes)
  85. UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  86. NET: Registered protocol family 1
  87. NetWinder Floating Point Emulator V0.97 (extended precision)
  88. init gpio code
  89. Netgear R7000 init
  90. PCI: no core
  91. PCI: no core
  92. PCI: scanning bus 0
  93. PCI host bridge to bus 0000:00
  94. pci_bus 0000:00: root bus resource [io  0x0000-0xffffffff]
  95. pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
  96. pci_bus 0000:00: root bus resource [bus 00-ff]
  97. pci 0000:00:11.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
  98. PCI: Fixing up bus 0 domain 0
  99. PCIE1 link=1
  100. PCIE1 switching to GEN2
  101. PCIE1 link=1
  102. PCI host bridge to bus 0001:00
  103. pci_bus 0001:00: root bus resource [mem 0x08000000-0x0fffffff]
  104. pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
  105. PCI: Fixing up bus 0 domain 1
  106. PCI: bus0: Fast back to back transfers disabled
  107. pci 0001:01:00.0: Max Payload Size set to 512 (was 128, max 512)
  108. PCI: Fixing up bus 1 domain 1
  109. PCI: bus1: Fast back to back transfers disabled
  110. pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
  111. pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
  112. pci 0001:00:00.0: PCI bridge to [bus 01]
  113. pci 0001:00:00.0:   bridge window [mem 0x08000000-0x080fffff]
  114. PCIE2 link=1
  115. PCIE2 switching to GEN2
  116. PCIE2 link=1
  117. PCI host bridge to bus 0002:00
  118. pci_bus 0002:00: root bus resource [mem 0x40000000-0x47ffffff]
  119. pci_bus 0002:00: No busn resource found for root bus, will use [bus 00-ff]
  120. PCI: Fixing up bus 0 domain 2
  121. PCI: bus0: Fast back to back transfers disabled
  122. pci 0002:01:00.0: Max Payload Size set to 512 (was 128, max 512)
  123. PCI: Fixing up bus 1 domain 2
  124. PCI: bus1: Fast back to back transfers disabled
  125. pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
  126. pci 0002:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
  127. pci 0002:00:00.0: PCI bridge to [bus 01]
  128. pci 0002:00:00.0:   bridge window [mem 0x40000000-0x400fffff]
  129. PCIE3 link=0
  130. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  131. io scheduler noop registered (default)
  132. io scheduler cfq registered
  133. serial8250_init
  134. Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
  135. console [ttyS0] disabled
  136. serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117, base_baud = 7812500) is a 16550
  137. console [ttyS0] enabled
  138. serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117, base_baud = 7812500) is a 16550
  139. brd: module loaded
  140. loop: module loaded
  141. bcmsflash: found no supported devices
  142. Boot partition size = 524288(0x80000)
  143. lookup_nflash_rootfs_offset: offset = 0x200000 size = 0x2000000, 0x20000
  144. found TRX Header on nflash!
  145. nflash: squash filesystem with lzma found at block 29
  146. Creating 5 MTD partitions on "nflash":
  147. 0x000000000000-0x000000080000 : "boot"
  148. 0x000000080000-0x000000200000 : "nvram"
  149. 0x000000200000-0x000002200000 : "linux"
  150. 0x0000003a0000-0x000002200000 : "rootfs"
  151. 0x000002200000-0x000002240000 : "board_data"
  152. tun: Universal TUN/TAP device driver, 1.6
  153. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  154. PPP generic driver version 2.4.2
  155. PPP BSD Compression module registered
  156. PPP Deflate Compression module registered
  157. PPP MPPE Compression module registered
  158. NET: Registered protocol family 24
  159. GACT probability NOT on
  160. Mirror/redirect action on
  161. Simple TC action Loaded
  162. netem: version 1.3
  163. u32 classifier
  164.    Performance counters on
  165.    input device check on
  166.    Actions configured
  167. Netfilter messages via NETLINK v0.30.
  168. nf_conntrack version 0.5.0 (3970 buckets, 15880 max)
  169. nf_conntrack_rtsp v0.7 loading
  170. xt_time: kernel timezone is -0000
  171. ip_set: protocol 6
  172. gre: GRE over IPv4 demultiplexor driver
  173. nf_nat_rtsp v0.7 loading
  174. ip_tables: (C) 2000-2006 Netfilter Core Team
  175. NET: Registered protocol family 17
  176. bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  177. Bridge firewalling registered
  178. 8021q: 802.1Q VLAN Support v1.8
  179. ThumbEE CPU extension supported.
  180. Registering SWP/SWPB emulation handler
  181. max nvram space = 131072
  182. read 65536 bytes to offset 0
  183. Key type encrypted registered
  184. Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
  185. nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
  186. nand: AMD/Spansion NAND 128MiB 3,3V 8-bit
  187. nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  188. Spare area=64 eccbytes 56, ecc bytes located at:
  189. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
  190. Available 7 bytes at (off,len):
  191. (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0)
  192. Scanning device for bad blocks
  193. Options: NO_SUBPAGE_WRITE,
  194. Creating 1 MTD partitions on "brcmnand":
  195. 0x000002240000-0x000008000000 : "ddwrt"
  196. VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
  197. Freeing unused kernel memory: 348K (804a7000 - 804fe000)
  198. Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
  199.  
  200. CPU0: stopping
  201. CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.52 #24
  202. Hardware name: Northstar Prototype
  203. Backtrace:
  204. [<8002d150>] (dump_backtrace) from [<8002d324>] (show_stack+0x18/0x1c)
  205. r7:804fff20 r6:60000193 r5:8051f3dc r4:00000000
  206. [<8002d30c>] (show_stack) from [<80171540>] (dump_stack+0x94/0xa8)
  207. [<801714ac>] (dump_stack) from [<8002ef88>] (handle_IPI+0x110/0x1a8)
  208. r7:804fff20 r6:00000000 r5:00000000 r4:805321ac
  209. [<8002ee78>] (handle_IPI) from [<800093dc>] (gic_handle_irq+0x78/0x7c)
  210. r7:b0100100 r6:804fff20 r5:b010010c r4:8050db18
  211. [<80009364>] (gic_handle_irq) from [<8000ab40>] (__irq_svc+0x40/0x54)
  212. Exception stack(0x804fff20 to 0x804fff68)
  213. ff20: 86dd4248 00000000 00000840 8000b7c0 804fe000 8050d8e0 80442c78 804f9224
  214. ff40: 804fff90 804d08c8 00000000 804fff7c 804fff80 804fff70 8002a9c0 8002a9c4
  215. ff60: 60000113 ffffffff
  216. r9:804d08c8 r8:804fff90 r7:804fff54 r6:ffffffff r5:60000113 r4:8002a9c4
  217. [<8002a988>] (arch_cpu_idle) from [<800806d4>] (default_idle_call+0x30/0x34)
  218. [<800806a4>] (default_idle_call) from [<800807e0>] (cpu_startup_entry+0x108/0x13c)
  219. [<800806d8>] (cpu_startup_entry) from [<8001674c>] (rest_init+0x80/0x84)
  220. r7:80532014 r4:00000000
  221. [<800166cc>] (rest_init) from [<804a7cbc>] (start_kernel+0x318/0x324)
  222. [<804a79a4>] (start_kernel) from [<0000807c>] (0x807c)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!