Default SNMPd Configuration

###########################################################################
#
# snmpd.conf
#
#   - created by the snmpconf configuration program
#
###########################################################################
# SECTION: Trap Destinations
#
#   Here we define who the agent will send traps to.

# trapsink: A SNMPv1 trap receiver
#   arguments: host [community] [portnum]

trapsink  192.168.0.1 public

# trap2sink: A SNMPv2c trap receiver
#   arguments: host [community] [portnum]

trap2sink  192.168.0.1 public

# authtrapenable: Should we send traps when authentication failures occur
#   arguments: 1 | 2   (1 = yes, 2 = no)

authtrapenable  1



###########################################################################
# SECTION: Access Control Setup
#
#   This section defines who is allowed to talk to your running
#   snmp agent.

# rocommunity: a SNMPv1/SNMPv2c read-only access community name
#   arguments:  community [default|hostname|network/bits] [oid]

rocommunity  public

# rwcommunity: a SNMPv1/SNMPv2c read-write access community name
#   arguments:  community [default|hostname|network/bits] [oid]

# rwcommunity  private






###########################################################################
# SECTION: System Information Setup
#
#   This section defines some of the information reported in
#   the "system" mib group in the mibII tree.

# syslocation: The [typically physical] location of the system.
#   Note that setting this value here means that when trying to
#   perform an snmp SET operation to the sysLocation.0 variable will make
#   the agent return the "notWritable" error code.  IE, including
#   this token in the snmpd.conf file will disable write access to
#   the variable.
#   arguments:  location_string

syslocation  "Set this to the location"

# syscontact: The contact information for the administrator
#   Note that setting this value here means that when trying to
#   perform an snmp SET operation to the sysContact.0 variable will make
#   the agent return the "notWritable" error code.  IE, including
#   this token in the snmpd.conf file will disable write access to
#   the variable.
#   arguments:  contact_string

syscontact  whoever@contact.com

# sysservices: The proper value for the sysServices object.
#   arguments:  sysservices_number

sysservices 76



###########################################################################
# SECTION: Monitor Various Aspects of the Running Host
#
#   The following check up on various aspects of a host.

# proc: Check for processes that should be running.
#     proc NAME [MAX=0] [MIN=0]
#
#     NAME:  the name of the process to check for.  It must match
#            exactly (ie, http will not find httpd processes).
#     MAX:   the maximum number allowed to be running.  Defaults to 0.
#     MIN:   the minimum number to be running.  Defaults to 0.
#
#   The results are reported in the prTable section of the UCD-SNMP-MIB tree
#   Special Case:  When the min and max numbers are both 0, it assumes
#   you want a max of infinity and a min of 1.

# proc

# load: Check for unreasonable load average values.
#   Watch the load average levels on the machine.
#
#    load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
#
#    1MAX:   If the 1 minute load average is above this limit at query
#            time, the errorFlag will be set.
#    5MAX:   Similar, but for 5 min average.
#    15MAX:  Similar, but for 15 min average.
#
#   The results are reported in the laTable section of the UCD-SNMP-MIB tree

load  5 5 5



###########################################################################
# SECTION: Agent Operating Mode
#
#   This section defines how the agent will operate when it
#   is running.

# agentaddress: The IP address and port number that the agent will listen on.
#   By default the agent listens to any and all traffic from any
#   interface on the default SNMP port (161).  This allows you to
#   specify which address, interface, transport type and port(s) that you
#   want the agent to listen on.  Multiple definitions of this token
#   are concatenated together (using ':'s).
#   arguments: [transport:]port[@interface/address],...

#agentaddress



#
# Unknown directives read in from other files by snmpconf
#
com2sec paranoid  default         public
group MyROSystem v1        paranoid
group MyROSystem v2c       paranoid
group MyROSystem usm       paranoid
group MyROGroup v1         readonly
group MyROGroup v2c        readonly
group MyROGroup usm        readonly
group MyRWGroup v1         readwrite
group MyRWGroup v2c        readwrite
group MyRWGroup usm        readwrite
view all    included  .1                               80
view system included  .iso.org.dod.internet.mgmt.mib-2.system
access MyROSystem ""     any       noauth    exact  system none   none
access MyROGroup ""      any       noauth    exact  all    none   none
access MyRWGroup ""      any       noauth    exact  all    all    none