U-Boot SPL 2014.04-10731-g30bf0a5-dirty (Nov 19 2014 - 23:08:42)
Board: Digma_iDj7n
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.04-10731-g30bf0a5-dirty (Nov 19 2014 - 23:08:42) Allwinner Technology

CPU:   Allwinner A13 (SUN5I)
Board: Digma_iDj7n
I2C:   ready
DRAM:  512 MiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
reading uEnv.txt
** Unable to read file uEnv.txt **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading boot.scr
334 bytes read in 16 ms (19.5 KiB/s)
Jumping to boot.scr
## Executing script at 44000000
reading script.bin
32164 bytes read in 29 ms (1.1 MiB/s)
reading uImage
4247288 bytes read in 307 ms (13.2 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.103-00033-g9a1cd03
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4247224 Bytes = 4.1 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<5>Linux version 3.4.103-00033-g9a1cd03 (kirill@RERE-Mint) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 PREEMPT Wed Nov 19 01:25:33 MSK 2014
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun5i
<6>Memory Reserved:
<6>	SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
<6>	LCD  : 0x50000000 - 0x51ffffff  (  32 MB)
<6>cma: CMA: reserved 192 MiB at 43c00000
Memory policy: ECC disabled, Data cache writeback
<6>sunxi: Allwinner A13 revision B (AW1625/sun5i) detected.
<7>On node 0 totalpages: 131072
<7>free_area_init_node: node 0, pgdat c0807824, node_mem_map d2000000
<7>  DMA zone: 512 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 65024 pages, LIFO batch:15
<7>  Normal zone: 512 pages used for memmap
<7>  Normal zone: 65024 pages, LIFO batch:15
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
<5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait panic=10
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 512MB = 512MB total
<5>Memory: 280936k/280936k available, 243352k reserved, 0K highmem
<5>Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc077c4e8   (7634 kB)
      .init : 0xc077d000 - 0xc07a6000   ( 164 kB)
      .data : 0xc07a6000 - 0xc08113f0   ( 429 kB)
       .bss : 0xc0811414 - 0xc08c58a0   ( 722 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>NR_IRQS:128
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop... <c>1001.88 BogoMIPS (lpj=5009408)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>CPU: Testing write buffer coherency: ok
<6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
<6>Setting up static identity map for 0x4052fed8 - 0x4052ff0c
<6>devtmpfs: initialized
<6>dummy:
<6>NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>hw-breakpoint: debug architecture 0x4 unsupported.
<6>Init eGon pin module V2.0
SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
<6>Initialize DMAC OK
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource aw_64bits_counter
<5>FS-Cache: Loaded
<6>CacheFiles: Loaded
[usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[sw_hcd0]: usb host driver initialize........
[sw_hcd0]: open_usb_clock
[sw_hcd0]: host_init_state = 0
[sw_hcd0]: platform is usb host
[sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
wrn: hcd is not enable, need not start hcd
[sw_hcd0]: sw_usb_host0_disable start
-------sw_hcd0_soft_disconnect---------
is_on = 0, hcd0_set_vbus_cnt = 0
[sw_hcd_host0]: Set USB Power Off
wrn: hcd is not enable, need not stop hcd
[sw_hcd0]: close_usb_clock
[sw_hcd0]: sw_usb_host0_disable end
[sw_udc]: udc_init: version 20080411
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP: reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.369:1): initialized
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.18)
<6>msgmni has been set to 932
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>sunxi disp driver loaded (/dev/disp api 1.0)
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<3>[uart]: failed to get uart3's used information
<6>brd: module loaded
<6>loop: module loaded
[NAND] nand driver version: 0x2 0x9
PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 0
<4>Dev Sunxi softw311 nand: part 1, start 32768, size 65536
<4>Dev Sunxi softw311 nand: part 2, start 98304, size 32768
<4>Dev Sunxi softw311 nand: part 3, start 131072, size 65536
<4>Dev Sunxi softw311 nand: part 4, start 196608, size 1331200
<4>Dev Sunxi softw311 nand: part 5, start 1527808, size 2457600
<4>Dev Sunxi softw311 nand: part 6, start 3985408, size 32768
<4>Dev Sunxi softw311 nand: part 7, start 4018176, size 65536
<4>Dev Sunxi softw311 nand: part 8, start 4083712, size 655360
<4>Dev Sunxi softw311 nand: part 9, start 4739072, size 524288
<4>Dev Sunxi softw311 nand: part 10, start 5263360, size 2519040
<6> nand: nanda nandb nandc nandd nande nandf nandg nandh nandi nandj
[NAND]nand driver, ok.
[spi]: sw spi init !!
[spi]: sw spi init fetch spi0 uning configuration failed
[spi]: Get spi devices number failed
[spi]: register spi devices board info failed
<4>spi: cannot find any using configuration for                     all 4 spi controllers, return directly!
<4>emac_init fetch emac using configuration failed
<6>emac driver is disabled
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[sw-ehci1]: open clock
[sw-ehci1]: Set USB Power ON
<6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
<6>sw-ehci sw-ehci.1: irq 39, io mem 0x01c14000
<6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
ehci_irq: port change detect
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
<6>[sw-ehci1]: disable ehci
<6>sw-ehci sw-ehci.1: remove, state 1
<6>usb usb2: USB disconnect, device number 1
<6>sw-ehci sw-ehci.1: USB bus 2 deregistered
[sw-ehci1]: Set USB Power OFF
[sw-ehci1]: close clock
[sw-ohci1]: open clock
[sw-ohci1]: Set USB Power ON
<6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 2
<6>sw-ohci sw-ohci.1: irq 40, io mem 0x01c14400
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
<6>[sw-ohci1]: disable ohci
<6>sw-ohci sw-ohci.1: remove, state 1
<6>usb usb2: USB disconnect, device number 1
<6>sw-ohci sw-ohci.1: USB bus 2 deregistered
[sw-ohci1]: Set USB Power OFF
[sw-ohci1]: close clock
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new interface driver ums-alauda
<6>usbcore: registered new interface driver ums-cypress
<6>usbcore: registered new interface driver ums-datafab
<6>usbcore: registered new interface driver ums_eneub6250
<6>usbcore: registered new interface driver ums-freecom
<6>usbcore: registered new interface driver ums-isd200
<6>usbcore: registered new interface driver ums-jumpshot
<6>usbcore: registered new interface driver ums-karma
<6>usbcore: registered new interface driver ums-onetouch
<6>usbcore: registered new interface driver ums-realtek
<6>usbcore: registered new interface driver ums-sddr09
<6>usbcore: registered new interface driver ums-sddr55
<6>usbcore: registered new interface driver ums-usbat
<6>mousedev: PS/2 mouse device common for all mice
<6>ecompass driver: init
<6>input: ecompass_data as /devices/virtual/input/input0
<6>mxc622x driver: init
========gsensor_fetch_sysconfig_para===================
<3>gsensor_fetch_sysconfig_para: line: 95 script_parser_fetch err.
<5>=========script_parser_fetch_err============
mxc622x_init: after fetch_sysconfig_para:  normal_i2c: 0x0. normal_i2c[1]: 0x0
========gsensor_fetch_sysconfig_para===================
<3>gsensor_fetch_sysconfig_para: line: 268 script_parser_fetch err.
<5>=========script_parser_fetch_err============
BMA250_init: after fetch_sysconfig_para:  normal_i2c: 0x0. normal_i2c[1]: 0x0
========RTC Inital ===================
rtc_fetch_sysconfig_para: after: rtc_twi_addr is 0x51, dirty_addr_buf: 0x51. dirty_addr_buf[1]: 0xfffe
rtc_fetch_sysconfig_para: rtc_twi_id is 1.
rtc_fetch_sysconfig_para:ok
pcf8563_init: after fetch_sysconfig_para:  normal_i2c: 0x51. normal_i2c[1]: 0xfffe
<6>i2c /dev entries driver
config i2c gpio with gpio_config api
<6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
<6>axp_mfd 0-0034: AXP internal temperature monitoring enabled
<4>i2c i2c-0: Invalid probe address 0x00
<4>i2c i2c-0: Invalid probe address 0x00
rtc_detect,line:157,twi_id:1,adapter->nr:0
rtc_detect,line:166
<6>I2C: i2c-0: AW16XX I2C adapter
config i2c gpio with gpio_config api
<4>i2c i2c-1: Invalid probe address 0x00
<4>i2c i2c-1: Invalid probe address 0x00
rtc_detect,line:157,twi_id:1,adapter->nr:1
<6>rtc_detect: Detected chip pcf8563 at adapter 1, address 0x51
rtc_detect,line:162
pcf8563_probe,line:666
<6>pcf8563 1-0051: chip found, driver version 0.4.3
<6>pcf8563 1-0051: low voltage detected, date/time is not reliable.
pcf8563_get_datetime,raw data is st1=08, st2=80, sec=b7, min=86, hr=93, mday=80, wday=b5, mon=a5, year=58
pcf8563_get_datetime: tm is secs=37, mins=6, hours=13,mday=0, mon=4, year=168, wday=5
<3>pcf8563 1-0051: retrieved date/time is not valid.
<6>pcf8563 1-0051: rtc core: registered pcf8563 as rtc0
<6>I2C: i2c-1: AW16XX I2C adapter
config i2c gpio with gpio_config api
<4>i2c i2c-2: Invalid probe address 0x00
<4>i2c i2c-2: Invalid probe address 0x00
rtc_detect,line:157,twi_id:1,adapter->nr:2
rtc_detect,line:166
<6>I2C: i2c-2: AW16XX I2C adapter
<6>lirc_dev: IR Remote Control driver registered, major 251
<6>IR NEC protocol handler initialized
<6>IR RC5(x) protocol handler initialized
<6>IR RC6 protocol handler initialized
<6>IR JVC protocol handler initialized
<6>IR Sony protocol handler initialized
<6>IR RC5 (streamzap) protocol handler initialized
<6>IR SANYO protocol handler initialized
<6>IR MCE Keyboard/mouse protocol handler initialized
<6>IR LIRC bridge handler initialized
[pa_drv] start!!!
[pa_drv] init end!!!
<6>axp20_ldo1: 1300 mV
<6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
<6>axp20_ldo3: 700 <--> 3500 mV at 3300 mV
<6>axp20_ldo4: 1250 <--> 3300 mV at 3300 mV
<6>axp20_buck2: 700 <--> 2275 mV at 1400 mV
<3>somebody is trying to set dcdc3 range to (1200000, 1200000) uV
<3>but we keep dcdc3 = 1250000 uV from the bootloader
<6>axp20_buck3: 700 <--> 3500 mV at 1250 mV
<6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
<6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input1
<4>axp20_ldo2: Failed to create debugfs directory
<6>cpuidle: using governor ladder
<6>[mmc-msg] sw_mci_init
<6>[mmc-msg] MMC host used card: 0x1, boot card: 0x0, io_card 0
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 Probe: base:0xf1c0f000 irq:32 sg_cpu:c3c40000(43c40000) ret 0.
[mmc_pm]: no sdio card used in configuration
<6>sunxi_leds driver init
<6>sunxi leds can't find script data '[leds_para]' 'leds_used'
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>IPv4 over IPv4 tunneling driver
<6>TCP: cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<6>8021q: 802.1Q VLAN Support v1.8
<5>Registering the dns_resolver key type
<6>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
<5>Registering SWP/SWPB emulation handler
<6>registered taskstats version 1
<6>Console: switching to colour frame buffer device 100x30
<6>I2C: i2c-3: HDMI I2C adapter
<4>axp20_buck3: incomplete constraints, leaving on
<4>axp20_buck2: incomplete constraints, leaving on
<4>axp20_ldo4: incomplete constraints, leaving on
<4>axp20_ldo3: incomplete constraints, leaving on
<4>axp20_ldo2: incomplete constraints, leaving on
<6>pcf8563 1-0051: low voltage detected, date/time is not reliable.
<6>[mmc-msg] mmc 0 detect change, present 1
pcf8563_get_datetime,raw data is st1=08, st2=80, sec=b8, min=86, hr=93, mday=80, wday=bd, mon=a5, year=58
pcf8563_get_datetime: tm is secs=38, mins=6, hours=13,mday=0, mon=4, year=168, wday=5
<3>pcf8563 1-0051: retrieved date/time is not valid.
<3>pcf8563 1-0051: hctosys: invalid date/time
<6>ALSA device list:
<6>  #0: sunxi-CODEC  Audio Codec
<4>Warning: unable to open an initial console.
<6>Waiting for root device /dev/mmcblk0p2...
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 power on
[ccmu] set sdc0 reset status to 0 failed!
<3>[mmc-err] Failed to release sdc0 reset
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
<3>[mmc-err] smc 0 err, cmd 52,  RTO
<3>[mmc-err] smc 0 err, cmd 52,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
<6>[mmc-msg] sdc0 set round clock 42857142, src 300000000
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
<6>mmc0: new high speed SDHC card at address 1234
<6>mmcblk0: mmc0:1234 SA04G 3.69 GiB
<6> mmcblk0: p1 p2
<3>EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
<3>EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244)


insmod_device_driver

[sw_udc]: sw_usb_device_enable start
[sw_udc]: usb_vbase  = 0xf1c13000
[sw_udc]: sram_vbase = 0xf1c00000
[sw_udc]: open_usb_clock
udc->driver is null, udc is need not start
[sw_udc]: sw_usb_device_enable end
<6>EXT4-fs (mmcblk0p2): recovery complete
<6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
<6>VFS: Mounted root (ext4 filesystem) on device 179:2.
<6>devtmpfs: mounted
<6>Freeing init memory: 164K
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<4>init: ureadahead main process (51) terminated with status 5
<4>init: Failed to open system console: No such device
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<30>udevd[133]: starting version 175
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<4>init: plymouth main process (52) killed by SEGV signal
<4>init: plymouth-splash main process (158) terminated with status 2
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
<3>init: Failed to create pty - disabling logging for job
<4>init: Temporary process spawn error: No such file or directory
^A^C