Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.01 13:36:19 =~=~=~=~=~=~=~=~=~=~=~=
- þ
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** MARVELL BOARD: RD-88F6281A LE
- U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19
- U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0
- Soc: 88F6281 A1 (DDR2)
- CPU running @ 1200Mhz L2 running @ 400Mhz
- SysClock = 400Mhz , TClock = 200Mhz
- DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
- DRAM CS[0] base 0x00000000 size 256MB
- DRAM Total size 256MB 16bit width
- Addresses 10M - 0M are saved for the U-Boot usage.
- Mem malloc Initialization (10M - 7M): Done
- NAND:128 MB
- Flash: 0 kB
- CPU : Marvell Feroceon (Rev 1)
- Kernel address is 0xc80000.
- Streaming disabled
- Write allocate disabled
- Module 0 is RGMII
- Module 1 is TDM
- USB 0: host mode
- PEX 0: PCI Express Root Complex Interface
- PEX interface detected Link X1
- Net: egiga0, egiga1 [PRIME]
- Hit any key to stop autoboot: 2 1 0
- NAND read: device 0 offset 0xc80000, size 0xa00000
- Reading data from 0xc80000 -- 0% complete.
- Reading data from 0xc99800 -- 1% complete.
- Reading data from 0xcb3000 -- 2% complete.
- Reading data from 0xccc800 -- 3% complete.
- Reading data from 0xce6000 -- 4% complete.
- Reading data from 0xcff800 -- 5% complete.
- Reading data from 0xd19800 -- 6% complete.
- Reading data from 0xd33000 -- 7% complete.
- Reading data from 0xd4c800 -- 8% complete.
- Reading data from 0xd66000 -- 9% complete.
- Reading data from 0xd7f800 -- 10% complete.
- Reading data from 0xd99800 -- 11% complete.
- Reading data from 0xdb3000 -- 12% complete.
- Reading data from 0xdcc800 -- 13% complete.
- Reading data from 0xde6000 -- 14% complete.
- Reading data from 0xdff800 -- 15% complete.
- Reading data from 0xe19800 -- 16% complete.
- Reading data from 0xe33000 -- 17% complete.
- Reading data from 0xe4c800 -- 18% complete.
- Reading data from 0xe66000 -- 19% complete.
- Reading data from 0xe7f800 -- 20% complete.
- Reading data from 0xe99800 -- 21% complete.
- Reading data from 0xeb3000 -- 22% complete.
- Reading data from 0xecc800 -- 23% complete.
- Reading data from 0xee6000 -- 24% complete.
- Reading data from 0xeff800 -- 25% complete.
- Reading data from 0xf19800 -- 26% complete.
- Reading data from 0xf33000 -- 27% complete.
- Reading data from 0xf4c800 -- 28% complete.
- Reading data from 0xf66000 -- 29% complete.
- Reading data from 0xf7f800 -- 30% complete.
- Reading data from 0xf99800 -- 31% complete.
- Reading data from 0xfb3000 -- 32% complete.
- Reading data from 0xfcc800 -- 33% complete.
- Reading data from 0xfe6000 -- 34% complete.
- Reading data from 0xfff800 -- 35% complete.
- Reading data from 0x1019800 -- 36% complete.
- Reading data from 0x1033000 -- 37% complete.
- Reading data from 0x104c800 -- 38% complete.
- Reading data from 0x1066000 -- 39% complete.
- Reading data from 0x107f800 -- 40% complete.
- Reading data from 0x1099800 -- 41% complete.
- Reading data from 0x10b3000 -- 42% complete.
- Reading data from 0x10cc800 -- 43% complete.
- Reading data from 0x10e6000 -- 44% complete.
- Reading data from 0x10ff800 -- 45% complete.
- Reading data from 0x1119800 -- 46% complete.
- Reading data from 0x1133000 -- 47% complete.
- Reading data from 0x114c800 -- 48% complete.
- Reading data from 0x1166000 -- 49% complete.
- Reading data from 0x117f800 -- 50% complete.
- Reading data from 0x1199800 -- 51% complete.
- Reading data from 0x11b3000 -- 52% complete.
- Reading data from 0x11cc800 -- 53% complete.
- Reading data from 0x11e6000 -- 54% complete.
- Reading data from 0x11ff800 -- 55% complete.
- Reading data from 0x1219800 -- 56% complete.
- Reading data from 0x1233000 -- 57% complete.
- Reading data from 0x124c800 -- 58% complete.
- Reading data from 0x1266000 -- 59% complete.
- Reading data from 0x127f800 -- 60% complete.
- Reading data from 0x1299800 -- 61% complete.
- Reading data from 0x12b3000 -- 62% complete.
- Reading data from 0x12cc800 -- 63% complete.
- Reading data from 0x12e6000 -- 64% complete.
- Reading data from 0x12ff800 -- 65% complete.
- Reading data from 0x1319800 -- 66% complete.
- Reading data from 0x1333000 -- 67% complete.
- Reading data from 0x134c800 -- 68% complete.
- Reading data from 0x1366000 -- 69% complete.
- Reading data from 0x137f800 -- 70% complete.
- Reading data from 0x1399800 -- 71% complete.
- Reading data from 0x13b3000 -- 72% complete.
- Reading data from 0x13cc800 -- 73% complete.
- Reading data from 0x13e6000 -- 74% complete.
- Reading data from 0x13ff800 -- 75% complete.
- Reading data from 0x1419800 -- 76% complete.
- Reading data from 0x1433000 -- 77% complete.
- Reading data from 0x144c800 -- 78% complete.
- Reading data from 0x1466000 -- 79% complete.
- Reading data from 0x147f800 -- 80% complete.
- Reading data from 0x1499800 -- 81% complete.
- Reading data from 0x14b3000 -- 82% complete.
- Reading data from 0x14cc800 -- 83% complete.
- Reading data from 0x14e6000 -- 84% complete.
- Reading data from 0x14ff800 -- 85% complete.
- Reading data from 0x1519800 -- 86% complete.
- Reading data from 0x1533000 -- 87% complete.
- Reading data from 0x154c800 -- 88% complete.
- Reading data from 0x1566000 -- 89% complete.
- Reading data from 0x157f800 -- 90% complete.
- Reading data from 0x1599800 -- 91% complete.
- Reading data from 0x15b3000 -- 92% complete.
- Reading data from 0x15cc800 -- 93% complete.
- Reading data from 0x15e6000 -- 94% complete.
- Reading data from 0x15ff800 -- 95% complete.
- Reading data from 0x1619800 -- 96% complete.
- Reading data from 0x1633000 -- 97% complete.
- Reading data from 0x164c800 -- 98% complete.
- Reading data from 0x1666000 -- 99% complete.
- Reading data from 0x167f800 -- 100% complete.
- 10485760 bytes read: OK
- ## Booting image at 02000000 ...
- Image Name: Linux-2.6.22.18
- Created: 2011-02-22 3:33:51 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 5701144 Bytes = 5.4 MB
- Load Address: 00008000
- Entry Point: 00008000
- Verifying Checksum ... OK
- OK
- Starting kernel ...
- Uncompressing Linux..................................................................................................................................................................................................................................................................... done, booting the kernel.
- Linux version 2.6.22.18 (root@Neo) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #2 Tue Feb 22 11:33:29 CST 2011
- CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
- Machine: Feroceon-KW
- Using UBoot passing parameters structure
- Memory policy: ECC disabled, Data cache writeback
- CPU0: D VIVT write-back cache
- CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- Built 1 zonelists. Total pages: 65024
- Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
- PID hash table entries: 1024 (order: 10, 4096 bytes)
- Console: colour dummy device 80x30
- Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- Memory: 256MB 0MB 0MB 0MB = 256MB total
- Memory: 251392KB available (4832K code, 403K data, 3116K init)
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- NET: Registered protocol family 16
- CPU Interface
- -------------
- SDRAM_CS0 ....base 00000000, size 256MB
- SDRAM_CS1 ....disable
- SDRAM_CS2 ....disable
- SDRAM_CS3 ....disable
- PEX0_MEM ....base e8000000, size 128MB
- PEX0_IO ....base f2000000, size 1MB
- INTER_REGS ....base f1000000, size 1MB
- NFLASH_CS ....base fa000000, size 2MB
- SPI_CS ....base f4000000, size 16MB
- BOOT_ROM_CS ....no such
- DEV_BOOTCS ....no such
- CRYPT_ENG ....base f0000000, size 2MB
- Marvell Development Board (LSP Version KW_LSP_4.2.7)-- RD-88F6281A Soc: MV88F6281 Rev 3 LE
- Detected Tclk 200000000 and SysClk 400000000
- Marvell USB EHCI Host controller #0: c0a9a600
- PEX0 interface detected Link X1
- PCI: bus0: Fast back to back transfers disabled
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- NET: Registered protocol family 2
- Time: kw_clocksource clocksource has been installed.
- IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
- TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- TCP reno registered
- RTC registered
- Use the XOR engines (acceleration) for enhancing the following functions:
- o RAID 5 Xor calculation
- o kernel memcpy
- o kenrel memzero
- Number of XOR engines to use: 4
- cesadev_init(c0011f5c)
- mvCesaInit: sessions=640, queue=64, pSram=f0000000
- Warning: TS unit is powered off.
- gpio_dev = fe00000
- LED_SET_CTL_IOC_NUM= 6702
- High gpio polarity = 50
- High gpio polarity = 70
- Enable Interrupt
- mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
- mv88f6281_wdt: HW Watchdog timeout = 15 sec.
- VFS: Disk quotas dquot_6.5.1
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- fuse init (API version 7.8)
- SGI XFS with large block numbers, no debug enabled
- SGI XFS Quota Management subsystem
- yaffs Feb 10 2011 21:07:53 Installing.
- io scheduler noop registered
- io scheduler cfq registered (default)
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
- serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
- RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
- loop: module loaded
- Loading Marvell Ethernet Driver:
- o Cached descriptors in DRAM
- o DRAM SW cache-coherency
- o Single RX Queue support - ETH_DEF_RXQ=0
- o Single TX Queue support - ETH_DEF_TXQ=0
- o TCP segmentation offload enabled
- o Receive checksum offload enabled
- o Transmit checksum offload enabled
- o Network Fast Processing (Routing) supported
- o Proc tool API enabled
- o Rx descripors: q0=128
- o Tx descripors: q0=532
- o Loading network interface(s):
- eth_get_config: Unexpected port number 0
- EthPort #0: Bad initialization parameters
- eth port=0: load failed
- eth_init_module: can't init eth_hal driver
- Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
- Copyright (c) 1999-2006 Intel Corporation.
- e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
- e100: Copyright(c) 1999-2006 Intel Corporation
- Integrated Sata device found
- scsi0 : Marvell SCSI to SATA adapter
- scsi1 : Marvell SCSI to SATA adapter
- scsi 0:0:0:0: Direct-Access WDC WD5000AAKX-221CA 15.0 PQ: 0 ANSI: 5
- EnablePowerSaving
- PowerSavingTime = 15
- /////////////////////////////////// init sd
- sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
- sd 0:0:0:0: [sda] Write Protect is off
- sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
- sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
- sd 0:0:0:0: [sda] Write Protect is off
- sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
- sda: sda1 sda2
- sd 0:0:0:0: [sda] Attached SCSI disk
- sd 0:0:0:0: Attached scsi generic sg0 type 0
- NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
- NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
- Scanning device for bad blocks
- Bad eraseblock 2 at 0x00040000
- Bad eraseblock 3 at 0x00060000
- Bad eraseblock 635 at 0x04f60000
- 9 cmdlinepart partitions found on MTD device nand_mtd
- Using command line partition definition
- Creating 9 MTD partitions on "nand_mtd":
- 0x00000000-0x00100000 : "uboot"
- 0x00100000-0x00180000 : "uboot_env"
- 0x00180000-0x00200000 : "key_store"
- 0x00200000-0x00280000 : "info"
- 0x00280000-0x00c80000 : "etc"
- 0x00c80000-0x01680000 : "kernel_1"
- 0x01680000-0x04640000 : "rootfs1"
- 0x04640000-0x05040000 : "kernel_2"
- 0x05040000-0x08000000 : "rootfs2"
- ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
- ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
- ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
- ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- USB Universal Host Controller Interface driver v3.0
- usb 1-1: new high speed USB device using ehci_marvell and address 2
- In hub_port_init, and number is 0, retry 0, port 1 .....
- usb 1-1: configuration #1 chosen from 1 choice
- hub 1-1:1.0: USB hub found
- hub 1-1:1.0: 4 ports detected
- usbcore: registered new interface driver usblp
- drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mice: PS/2 mouse device common for all mice
- i2c /dev entries driver
- i2c-adapter i2c-0: Unrecognized version/stepping 0x69 Defaulting to Generic LM85.
- hwmon-vid: Unknown VRM version of your CPU
- md: linear personality registered for level -1
- md: raid0 personality registered for level 0
- md: raid1 personality registered for level 1
- raid6: int32x1 95 MB/s
- raid6: int32x2 138 MB/s
- raid6: int32x4 125 MB/s
- raid6: int32x8 111 MB/s
- raid6: using algorithm int32x2 (138 MB/s)
- md: raid6 personality registered for level 6
- md: raid5 personality registered for level 5
- md: raid4 personality registered for level 4
- raid5: measuring checksumming speed
- arm4regs : 1090.800 MB/sec
- 8regs : 653.600 MB/sec
- 32regs : 884.400 MB/sec
- raid5: using function: arm4regs (1090.800 MB/sec)
- device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
- usbcore: registered new interface driver hiddev
- usbcore: registered new interface driver usbhid
- drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
- TCP cubic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- Freeing init memory: 3116K
- [031m*** Stage 1: Setup system and device drivers ***[0m
- r8168 Gigabit Ethernet driver 8.012.00-NAPI loaded
- pci_resource_start(pdev, 2) = e8014000
- r8168 0000:00:01.0: no MSI. Back to INTx.
- Set LED ...
- r8168: This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776, and US6,327,625.
- eth0: RTL8168B/8111B at 0xd0854000, 00:00:00:00:00:30, IRQ 9
- ioaddr = d0854000
- r8168 Copyright (C) 2009 Realtek NIC software team <nicfae@realtek.com>
- This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
- This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
- r8168: egiga0: link down
- [031m*** Stage 2: Prepare the root file system ***[0m
- [033mMount system partition...[0m
- yaffs: dev is 32505862 name is "mtdblock6"
- yaffs: passed flags ""
- yaffs: Attempting MTD mount on 31.6, "mtdblock6"
- yaffs_read_super: isCheckpointed 0
- e2fsck 1.38 (30-Jun-2005)
- /dev/sda1: clean, 13/128520 files, 156045/514048 blocks
- kjournald starting. Commit interval 5 seconds
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3-fs: mounted filesystem with ordered data mode.
- /dev/sda1 /zyxel/mnt/sysdisk ext3 ro,data=ordered 0 0
- 0
- Boot from disk
- r8168: egiga0: link up
- r8168: egiga0: link up
- Checksum of sysdisk.img : c3b9c0928749408b90d766aaa95b9ce7
- Checksum from INFO : 7ddf39bd27e18147c31a7d325e5acc98
- Checksum pass!
- EXT3 FS on sda1, internal journal
- [033mMount system disk image ...[0m
- cp: /ram_bin/bin/*: No such file or directory
- yaffs: dev is 32505860 name is "mtdblock4"
- yaffs: passed flags ""
- yaffs: Attempting MTD mount on 31.4, "mtdblock4"
- yaffs: restored from checkpoint
- yaffs_read_super: isCheckpointed 1
- /etc/zyxel/conf exist..
- tar: Couldnt chdir to /etc/init.d/service_conf/: No such file or directory
- going to copy the 320 conf to /etc/zyxel...
- rm: unable to remove `/etc/zyxel/lost+found': Directory not empty
- Start rcS2 of ZyXEL style
- [031m*** Stage 3: Start services on HDD ***[0m
- NTFS driver 2.1.28 [Flags: R/O MODULE].
- tntfs: module license 'Commercial' taints kernel.
- Tuxera NTFS driver 3010.6.16 [Flags: R/W MODULE].
- PPP generic driver version 2.4.2
- PPP MPPE Compression module registered
- ppp_async: Unknown symbol crc_ccitt_table
- insmod: cannot insert `/lib/modules/2.6.22.18/kernel/drivers/net/ppp_async.ko': Unknown symbol in module (-1): No such file or directory
- PPP Deflate Compression module registered
- NET: Registered protocol family 24
- PPP BSD Compression module registered
- modprobe: module fuse not found.
- modprobe: failed to load module fuse
- Starting PID Fan Control..
- P:20, I:1, D:5, SampleRate:10 seconds, ST_CPU:46, ST_ADT7463:46, ST_DauBoard:46
- Wt_CPU:0, Wt_ADT7463:0, Wt_DauBoard:1
- Tolerance:1 MinPwm:0x40
- sda
- checking sda
- Trying to mount /dev/sda1
- Press ENTER to continue...
- Starting zylogd...
- zylog starts.
- Starting uamd...
- Starting ZySH daemon and client...
- Start NSA-220 system daemon....
- Start ZySH daemon
- zyshd: version 2.0.0 (build: 11:39:50 Aug 19 2010)
- % zylog init start
- cat: /var/run/syslog-ng.pid: No such file or directory
- Try to KILL SIGHUP to syslog-ng: pid=0
- syslog-ng not running, start /usr/sbin/syslog-ng
- Dec 1 12:37:04 (none) syslog-ng[1160]: syslog-ng starting up; version='2.0.10'
- zyio_open_config success. (/etc/__system_default.xml, 0)
- zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
- /usr/sbin/zic -d /etc /var/zyxel/myzone_rule
- /bin/ln -s -f /etc/MyZone /etc/localtime
- /bin/hostname HomeDisk
- Usage: umount [-hV]
- umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
- umount [-f] [-F] [-r] [-n] [-v] special | node...
- Usage: umount [-hV]
- umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
- umount [-f] [-F] [-r] [-n] [-v] special | node...
- BusyBox v1.1.1 (2011.01.26-03:51+0000) multi-call binary
- Usage: rmdir [OPTION]... DIRECTORY...
- Init SMB DB access...
- rm: cannot remove `/var/log/samba/smb.db': No such file or directory
- Generating a 1024 bit RSA private key
- ...........................++++++
- .....++++++
- writing new private key to '/etc/zyxel/cert/key/default_key.cer'
- -----
- zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed
- Assemble volume....
- [1204] server write-only FIFO is opened (fd=6)
- [1204] server read-only FIFO is opened (fd=7)
- [1204] server error read-only FIFO is opened (fd=8)
- argc = 1, func = 276
- md: md0 stopped.
- md: bind<sda2>
- cat: /tmp/mduuid.map: No such file or directory
- Filesystem "md0": Disabling barriers, not supported by the underlying device
- XFS mounting filesystem md0
- Startup config
- POLLHUP on 7
- pid = 1204
- [1204] is disconnected
- [1273] server write-only FIFO is opened (fd=6)
- [1273] server read-only FIFO is opened (fd=7)
- [1273] server error read-only FIFO is opened (fd=8)
- argc = 1, func = 14
- argc = 1, func = 17
- argc = 2, func = 104
- argid[1]: 1059; argv[1]: ge1
- argc = 5, func = 107
- argid[1]: 1059; argv[1]: ge1
- argid[2]: 313; argv[2]: ip
- argid[3]: 434; argv[3]: address
- argid[4]: 538; argv[4]: dhcp
- argc = 3, func = 105
- argid[1]: 1059; argv[1]: ge1
- argid[2]: 350; argv[2]: exit
- argc = 2, func = 418
- argid[1]: 1052; argv[1]: 192.168.1.1
- argc = 3, func = 420
- argid[1]: 857; argv[1]: fetch
- argid[2]: 627; argv[2]: auto
- /bin/rm -f /var/zyxel/zysh/egiga0.metric
- /bin/ip route del default via 0.0.0.0 dev egiga0
- ip: RTNETLINK answers: No such process
- [1278] server write-only FIFO is opened (fd=9)
- [1278] server read-only FIFO is opened (fd=10)
- [1278] server error read-only FIFO is opened (fd=11)
- argc = 1, func = 72
- /usr/sbin/ntpdate_agent
- argc = 1, func = 419
- POLLHUP on 10
- pid = 1278
- [1278] is disconnected
- argc = 2, func = 68
- argid[1]: 1051; argv[1]: time.stdtime.gov.tw
- argc = 2, func = 60
- argid[1]: 1102; argv[1]: +0800
- /usr/sbin/zic -d /etc /var/zyxel/myzone_rule
- /bin/ln -s -f /etc/MyZone /etc/localtime
- Dec 1 20:37:15 (none) ntpdate[1314]: can't find host time.stdtime.gov.tw
- Dec 1 20:37:15 (none) ntpdate[1314]: no servers can be used, exiting
- argc = 1, func = 38
- killall: pure-ftpd: no process killed
- Usage: umount [-hV]
- umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
- umount [-f] [-F] [-r] [-n] [-v] special | node...
- Usage: umount [-hV]
- umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
- umount [-f] [-F] [-r] [-n] [-v] special | node...
- BusyBox v1.1.1 (2011.01.26-03:51+0000) multi-call binary
- Usage: rmdir [OPTION]... DIRECTORY...
- Dec 1 20:37:15 (none) dhcpcd[1300]: dhcpT1value is 43200 sec
- Dec 1 20:37:15 (none) dhcpcd[1300]: dhcpT2value is 75600 sec
- Dec 1 20:37:15 (none) dhcpcd[1300]: dhcpT1value is 43200 sec
- Dec 1 20:37:15 (none) dhcpcd[1300]: dhcpT2value is 75600 sec
- [1371] server write-only FIFO is opened (fd=9)
- [1371] server read-only FIFO is opened (fd=10)
- [1371] server error read-only FIFO is opened (fd=11)
- argc = 1, func = 395
- Dec 1 20:37:20 (none) ntpdate[1429]: step time server 128.105.39.11 offset 0.756164 sec
- argc = 3, func = 421
- argid[1]:DisablePowerSaving
- 1059; argv[1]: TimerState = 1
- ge1
- argid[2]: 1EnablePowerSaving
- 052; argv[2]: 19PowerSavingTime = 15
- 2.168.1.1
- argc = 2, func = 392
- argid[1]: 1216; argv[1]: yes
- argc = 2, func = 146
- argid[1]: 1127; argv[1]: 15
- test0
- Test1
- Test2
- Test3:
- argc = 2, func = 160
- argid[1]: 1132; argv[1]: g
- Error: Read failed
- exec_cmd complete
- eth status = d
- ethtest0
- Test1
- Test2
- Test3:
- Can not change wol setting by ioctl
- argc = 2, func = 18
- argid[1]: 350; argv[1]: exit
- POLLHUP on 10
- pid = 1371
- [1371] is disconnected
- argc = 1, func = 20
- POLLHUP on 7
- pid = 1273
- [1273] is disconnected
- [1438] server write-only FIFO is opened (fd=6)
- [1438] server read-only FIFO is opened (fd=7)
- [1438] server error read-only FIFO is opened (fd=8)
- argc = 1, func = 422
- POLLHUP on 7
- pid = 1438
- [1438] is disconnected
- configure terminal ip smb internal enable "/i-data/md0"
- [1451] server write-only FIFO is opened (fd=6)
- [1451] server read-only FIFO is opened (fd=7)
- [1451] server error read-only FIFO is opened (fd=8)
- argc = 4, func = 180
- argid[1]: 629; argv[1]: internal
- argid[2]: 302; argv[2]: enable
- argid[3]: 1154; argv[3]: "/i-data/md0"
- smb_share.c: editing_config lack of smb_global settings
- RegenSmbConfigFile:2114 Close file ok
- POLLHUP on 7
- pid = 1451
- [1451] is disconnected
- Starting smbd...
- Starting nmbd...
- Starting NSU Agent...
- readlink: /i-data/md1: No such file or directory
- configure terminal ip smb internal disable "/i-data/md1"
- [1470] server write-only FIFO is opened (fd=6)
- [1470] server read-only FIFO is opened (fd=7)
- [1470] server error read-only FIFO is opened (fd=8)
- argc = 4, func = 181
- argid[1]: 629; argv[1]: internal
- argid[2]: 303; argv[2]: disable
- argid[3]: 1154; argv[3]: "/i-data/md1"
- smb_share.c: editing_config lack of smb_global settings
- RegenSmbConfigFile:2114 Close file ok
- POLLHUP on 7
- pid = 1470
- [1470] is disconnected
- configure terminal ip smb internal enable "/i-data/f897e6ca"
- [1483] server write-only FIFO is opened (fd=6)
- [1483] server read-only FIFO is opened (fd=7)
- [1483] server error read-only FIFO is opened (fd=8)
- argc = 4, func = 180
- argid[1]: 629; argv[1]: internal
- argid[2]: 302; argv[2]: enable
- argid[3]: 1154; argv[3]: "/i-data/f897e6ca"
- smb_share.c: editing_config lack of smb_global settings
- RegenSmbConfigFile:2114 Close file ok
- POLLHUP on 7
- pid = 1483
- [1483] is disconnected
- Starting crond...
- Adding 524280k swap on /i-data/.zyxel/swap_ul6545p. Priority:-1 extents:3 across:244099264k
- 341+0 records in
- 341+0 records out
- Setting up swapspace version 1, size = 357560 kB
- GMT offset=28800s
- setting system time zone to tz_minuteswest=-480
- mknod: /dev/btncpy: File exists
- setLED COPY OFF
- [1655] server write-only FIFO is opened (fd=6)
- [1655] server read-only FIFO is opened (fd=7)
- [1655] server error read-only FIFO is opened (fd=8)
- argc = 1, func = 19
- POLLHUP on 7
- pid = 1655
- [1655] is disconnected
- led_state_map_addr = 10
- [1716] server write-only FIFO is opened (fd=6)
- [1716] server read-only FIFO is opened (fd=7)
- [1716] server error read-only FIFO is opened (fd=8)
- argc = 2, func = 345
- argid[1]: 1197; argv[1]: former
- Fail to enable power resume
- POLLHUP on 7
- pid = 1716
- [1716] is disconnected
- ===> Starting schedule_controller ...
- killall: timer_source: no process killed
- Starting "/etc/init.d/zypkg_controller.sh".
- Starting to set up zy-pkgs environment ...
- cp: /etc/zyxel/zy-pkgs/*: No such file or directory
- du: /usr/local/zy-pkgs/tmp/zypkg.log: No such file or directory
- [: 10240: unknown operand
- Finish "/etc/init.d/zypkg_controller.sh".
- Starting "/etc/init.d/zypkg_controller.sh".
- Starting all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
- - starting package "PHP-MySQL-phpMyAdmin" ...
- ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/PHP-MySQL-phpMyAdmin" is not existed or not excutable
- - starting package "SqueezeCenter" ...
- ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SqueezeCenter" is not existed or not excutable
- - starting package "SMART" ...
- ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SMART" is not existed or not excutable
- /etc/init.d/zypkg_controller.sh: /etc/init.d/zypkg_controller.sh: 491: cannot open /i-data/md0/admin/zy-pkgs/USRPKG_DEPS_START: No such file
- Finish "/etc/init.d/zypkg_controller.sh".
- Starting Web Server...
- Dec 1 20:37:40 (none) httpd[1897]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
- Dec 1 20:37:40 (none) httpd[1897]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
- Dec 1 20:37:40 (none) httpd[1897]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!?
- Dec 1 20:37:40 (none) httpd[1897]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
- Dec 1 20:37:40 (none) httpd[1897]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!?
- Dec 1 20:37:40 (none) httpd[1897]: [error] mod_auth_zyxel: initialized.
- Starting app_wd...
- [031m core_checksum [0m: 60e5ac84547193df98917040f063855e
- [031m fwversion [0m: V3.34(AFN.2)
- [031m img_checksum [0m: 7ddf39bd27e18147c31a7d325e5acc98
- [031m modelid [0m: DA01
- [031m revision [0m: 29152
- [031m romfile_checksum [0m: 1A7D
- [031m zld_checksum [0m: 72ff7c00ebca9f21c3129d854d47cdb7
- led_state_map_addr = 46
- Dec 1 12:37:43 (none) linuxrc: Starting pid 193Dec 1 20:37:43 (none) httpd[1898]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
- Dec 1 20:37:43 (none) httpd[1898]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!?
- Dec 1 20:37:43 (none) httpd[1898]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
- Dec 1 20:37:43 (none) httpd[1898]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!?
- Dec 1 20:37:43 (none) httpd[1898]: [error] mod_auth_zyxel: initialized.
- HomeDisk login: Dec 1 20:40:11 (none) weblogin.cgi: PAM _pam_init_handlers: no default config /etc/pam.d/other
- Dec 1 20:40:11 (none) PAM_smbpass[2155]: Cannot access samba password database, not running as root.
- Dec 1 20:40:25 (none) weblogin.cgi: PAM _pam_init_handlers: no default config /etc/pam.d/other
- Dec 1 20:40:25 (none) PAM_smbpass[2186]: Cannot access samba password database, not running as root.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement