API tools faq
paste
Advertisement
addict3d2life

Kernel output 3.10.53

addict3d2life
Jul 10th, 2015
460
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 23.32 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 2014.07-00136-gf870252 (Sep 22 2014 - 09:16:34)
  2.  
  3. CPU: Freescale i.MX6Q rev1.2 at 792 MHz
  4. Reset cause: POR
  5. Board: Nitrogen6X
  6. I2C: ready
  7. DRAM: 1 GiB
  8. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  9. SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB
  10. Display: LDB-WXGA (1280x800)
  11. In: serial
  12. Out: serial
  13. Err: serial
  14. Net: using phy at 6
  15. FEC [PRIME], usb_ether
  16. Hit any key to stop autoboot: 0
  17. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
  18. flags: ncq stag pm led clo only pmp pio slum part
  19. No port device detected!
  20. ** Bad device size - sata 0 **
  21.  
  22. SATA device 1: unknown device
  23. ** Bad device sata 1 **
  24. switch to partitions #0, OK
  25. mmc0 is current device
  26. 5549 bytes read in 33 ms (164.1 KiB/s)
  27. ## Executing script at 10008000
  28. ** File not found uEnv.txt **
  29. 51153 bytes read in 63 ms (792 KiB/s)
  30. Setting bus to 1
  31. Valid chip addresses:
  32. ------ no HDMI monitor
  33. libfdt fdt_path_offset() returned FDT_ERR_BADPATH
  34. libfdt fdt_path_offset() returned FDT_ERR_BADPATH
  35. Setting bus to 2
  36. Valid chip addresses:
  37. ------ no Freescale display
  38. Valid chip addresses:
  39. ------ no ft5x06 touch controller
  40. libfdt fdt_path_offset() returned FDT_ERR_BADPATH
  41. Valid chip addresses:
  42. Valid chip addresses:
  43. 6322744 bytes read in 361 ms (16.7 MiB/s)
  44. 726407 bytes read in 109 ms (6.4 MiB/s)
  45. ## Booting kernel from Legacy Image at 10800000 ...
  46. Image Name: Linux-3.10.53-ga29c1cb
  47. Image Type: ARM Linux Kernel Image (uncompressed)
  48. Data Size: 6322680 Bytes = 6 MiB
  49. Load Address: 10008000
  50. Entry Point: 10008000
  51. Verifying Checksum ... OK
  52. ## Loading init Ramdisk from Legacy Image at 12800000 ...
  53. Image Name: RAM Disk
  54. Image Type: ARM Linux RAMDisk Image (gzip compressed)
  55. Data Size: 726343 Bytes = 709.3 KiB
  56. Load Address: 00000000
  57. Entry Point: 00000000
  58. Verifying Checksum ... OK
  59. ## Flattened Device Tree blob at 12000000
  60. Booting using the fdt blob at 0x12000000
  61. Loading Kernel Image ... OK
  62. Using Device Tree in place at 12000000, end 1200f7d0
  63.  
  64. Starting kernel ...
  65.  
  66. Booting Linux on physical CPU 0x0
  67. Initializing cgroup subsys cpu
  68. Initializing cgroup subsys cpuacct
  69. Linux version 3.10.53-ga29c1cb (gbisson@t450s) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #7 SMP PREEMPT Tue Jun 23 08:59:07 UTC 2015
  70. CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
  71. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  72. Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad Nitrogen6x Board
  73. cma: CMA: reserved 256 MiB at 3a000000
  74. Memory policy: ECC disabled, Data cache writealloc
  75. PERCPU: Embedded 8 pages/cpu @8139d000 s9728 r8192 d14848 u32768
  76. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259840
  77. Kernel command line: console=ttymxc1,115200 vmalloc=400M consoleblank=0 rootwait androidboot.hardware=freescale androidboot.bootdev=mmcblk2 androidboot.serialno=19b8013dd8
  78. PID hash table entries: 4096 (order: 2, 16384 bytes)
  79. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  80. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  81. Memory: 959MB 64MB = 1023MB total
  82. Memory: 763108k/763108k available, 285468k reserved, 0K highmem
  83. Virtual kernel memory layout:
  84. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  85. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  86. vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
  87. lowmem : 0x80000000 - 0xc0000000 (1024 MB)
  88. pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  89. modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  90. .text : 0x80008000 - 0x80a295f4 (10374 kB)
  91. .init : 0x80a2a000 - 0x80a75600 ( 302 kB)
  92. .data : 0x80a76000 - 0x80af40e0 ( 505 kB)
  93. .bss : 0x80af40e0 - 0x80b854ec ( 582 kB)
  94. SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  95. Preemptible hierarchical RCU implementation.
  96. NR_IRQS:16 nr_irqs:16 16
  97. L310 cache controller enabled
  98. l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
  99. sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  100. CPU identified as i.MX6Q, silicon rev 1.2
  101. Console: colour dummy device 80x30
  102. Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  103. pid_max: default: 32768 minimum: 301
  104. Security Framework initialized
  105. SELinux: Initializing.
  106. Mount-cache hash table entries: 512
  107. Initializing cgroup subsys debug
  108. Initializing cgroup subsys freezer
  109. CPU: Testing write buffer coherency: ok
  110. CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  111. Setting up static identity map for 0x80766fe0 - 0x80767038
  112. CPU1: Booted secondary processor
  113. CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  114. CPU2: Booted secondary processor
  115. CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
  116. CPU3: Booted secondary processor
  117. CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
  118. Brought up 4 CPUs
  119. SMP: Total of 4 processors activated (6324.22 BogoMIPS).
  120. CPU: All CPU(s) started in SVC mode.
  121. devtmpfs: initialized
  122. pinctrl core: initialized pinctrl subsystem
  123. regulator-dummy: no parameters
  124. NET: Registered protocol family 16
  125. DMA: preallocated 256 KiB pool for atomic coherent allocations
  126. Use WDOG1 as reset source
  127. syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
  128. vdd1p1: 800 <--> 1375 mV at 1100 mV
  129. vdd3p0: 2625 <--> 3400 mV at 3000 mV
  130. vdd2p5: 2000 <--> 2750 mV at 2400 mV
  131. cpu: 725 <--> 1450 mV at 1150 mV
  132. vddpu: 725 <--> 1450 mV at 1150 mV
  133. vddsoc: 725 <--> 1450 mV at 1175 mV
  134. syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
  135. syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
  136. hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  137. hw-breakpoint: maximum watchpoint size is 4 bytes.
  138. imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
  139. bio: create slab <bio-0> at 0
  140. 1P8V: 1800 mV
  141. 2P5V: 2500 mV
  142. 3P3V: 3300 mV
  143. usb_otg_vbus: 5000 mV
  144. wlan-en: 1800 mV
  145. vgaarb: loaded
  146. SCSI subsystem initialized
  147. usbcore: registered new interface driver usbfs
  148. usbcore: registered new interface driver hub
  149. usbcore: registered new device driver usb
  150. i2c i2c-0: IMX I2C adapter registered
  151. i2c i2c-1: IMX I2C adapter registered
  152. i2c i2c-2: IMX I2C adapter registered
  153. Linux video capture interface: v2.00
  154. pps_core: LinuxPPS API ver. 1 registered
  155. pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  156. PTP clock support registered
  157. imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  158. imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  159. mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
  160. mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
  161. MIPI CSI2 driver module loaded
  162. Advanced Linux Sound Architecture Driver Initialized.
  163. Bluetooth: Core ver 2.16
  164. NET: Registered protocol family 31
  165. Bluetooth: HCI device and connection manager initialized
  166. Bluetooth: HCI socket layer initialized
  167. Bluetooth: L2CAP socket layer initialized
  168. Bluetooth: SCO socket layer initialized
  169. cfg80211: Calling CRDA to update world regulatory domain
  170. pureg-dummy: no parameters
  171. Switching to clocksource mxc_timer1
  172. imx6q-pcie 1ffc000.pcie: phy link never came up
  173. imx6q-pcie 1ffc000.pcie: failed to initialize host
  174. NET: Registered protocol family 2
  175. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  176. TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  177. TCP: Hash tables configured (established 8192 bind 8192)
  178. TCP: reno registered
  179. UDP hash table entries: 512 (order: 2, 16384 bytes)
  180. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  181. NET: Registered protocol family 1
  182. RPC: Registered named UNIX socket transport module.
  183. RPC: Registered udp transport module.
  184. RPC: Registered tcp transport module.
  185. RPC: Registered tcp NFSv4.1 backchannel transport module.
  186. Trying to unpack rootfs image as initramfs...
  187. Freeing initrd memory: 704K (82801000 - 828b1000)
  188. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  189. imx6_busfreq busfreq.17: DDR medium rate not supported.
  190. Bus freq driver module loaded
  191. futex hash table entries: 1024 (order: 4, 65536 bytes)
  192. audit: initializing netlink socket (disabled)
  193. type=2000 audit(0.680:1): initialized
  194. VFS: Disk quotas dquot_6.5.2
  195. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  196. NFS: Registering the id_resolver key type
  197. Key type id_resolver registered
  198. Key type id_legacy registered
  199. NTFS driver 2.1.30 [Flags: R/W DEBUG].
  200. fuse init (API version 7.22)
  201. msgmni has been set to 2003
  202. io scheduler noop registered
  203. io scheduler deadline registered
  204. io scheduler cfq registered (default)
  205. /soc/aips-bus@02000000/ldb@020e0008/lvds-channel@0: no timings specified
  206. /soc/aips-bus@02000000/ldb@020e0008/lvds-channel@0: no timings specified
  207. ldb: probe of ldb.15 failed with error -22
  208. imx-sdma 20ec000.sdma: no iram assigned, using external mem
  209. imx-sdma 20ec000.sdma: loaded firmware 1.1
  210. imx-sdma 20ec000.sdma: initialized
  211. Serial: IMX driver
  212. 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  213. 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
  214. console [ttymxc1] enabled
  215. 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
  216. serial: Freescale lpuart driver
  217. imx sema4 driver is registered.
  218. [drm] Initialized drm 1.1.0 20060810
  219. [drm] Initialized vivante 1.0.0 20120216 on minor 0
  220. brd: module loaded
  221. loop: module loaded
  222. (stk) :sysfs entries created
  223. (hci_tty): inside hci_tty_init
  224. (hci_tty): allocated 247, 0
  225. Wait for CR ACK error!
  226. sata phy RX_PLL is stable!
  227. ahci: SSS flag set, parallel bus scan disabled
  228. ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
  229. ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
  230. scsi0 : ahci_platform
  231. ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
  232. m25p80 spi32766.0: sst25vf016b (2048 Kbytes)
  233. 3 ofpart partitions found on MTD device spi32766.0
  234. Creating 3 MTD partitions on "spi32766.0":
  235. 0x000000000000-0x0000000c0000 : "U-Boot"
  236. 0x0000000c0000-0x0000000c2000 : "env"
  237. 0x0000000c2000-0x000000200000 : "splash"
  238. spi_imx 2008000.ecspi: probed
  239. tun: Universal TUN/TAP device driver, 1.6
  240. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  241. CAN device driver interface
  242. flexcan 2090000.can: device registered (reg_base=c0a28000, irq=142)
  243. phyirq=188
  244. libphy: fec_enet_mii_bus: probed
  245. fec 2188000.ethernet eth0: registered PHC device 0
  246. PPP generic driver version 2.4.2
  247. PPP BSD Compression module registered
  248. PPP Deflate Compression module registered
  249. PPP MPPE Compression module registered
  250. NET: Registered protocol family 24
  251. hso: drivers/net/usb/hso.c: Option Wireless
  252. usbcore: registered new interface driver hso
  253. usbcore: registered new interface driver cdc_ether
  254. usbcore: registered new interface driver cdc_eem
  255. usbcore: registered new interface driver cdc_ncm
  256. usbcore: registered new interface driver cdc_mbim
  257. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  258. ehci-pci: EHCI PCI platform driver
  259. usbcore: registered new interface driver cdc_acm
  260. cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  261. usbcore: registered new interface driver cdc_wdm
  262. usbcore: registered new interface driver usb-storage
  263. usbcore: registered new interface driver usbserial
  264. usbcore: registered new interface driver option
  265. usbserial: USB Serial support registered for GSM modem (1-port)
  266. usbcore: registered new interface driver pl2303
  267. usbserial: USB Serial support registered for pl2303
  268. usbcore: registered new interface driver qcserial
  269. usbserial: USB Serial support registered for Qualcomm USB modem
  270. setup_reset_gpios:-2, flags 0
  271. setup_reset_gpios:-2, flags 0
  272. ci_hdrc ci_hdrc.1: doesn't support gadget
  273. ci_hdrc ci_hdrc.1: EHCI Host Controller
  274. ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
  275. ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
  276. hub 1-0:1.0: USB hub found
  277. hub 1-0:1.0: 1 port detected
  278. mousedev: PS/2 mouse device common for all mice
  279. egalax_ts 2-0004: Failed to read firmware version
  280. egalax_ts: probe of 2-0004 failed with error -5
  281. ft5x06-ts 2-0038: ft5x06: Could not detect touch screen.
  282. ft5x06: Jun 3 2015
  283. ili210x_i2c 2-0041: No platform data!
  284. ili210x_i2c 2-0041: i2c transfer failed
  285. ili210x_i2c 2-0041: Failed to get firmware version, err: -5
  286. ili210x_i2c: probe of 2-0041 failed with error -5
  287. setup_reset_gpio:-2
  288. setup_irq_gpio:-2
  289. tsc2004_prepare_for_reading: write_cmd -5
  290. tsc2004: probe of 2-0048 failed with error -5
  291. rtc-isl1208 0-006f: chip found, driver version 0.3
  292. rtc-isl1208 0-006f: rtc core: registered rtc-isl1208 as rtc0
  293. check_alarm_past: alarm in the past
  294. snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1
  295. i2c /dev entries driver
  296. ata1: SATA link down (SStatus 0 SControl 300)
  297. update_device_addr: ov5642 ret=-5
  298. ov5642_read_reg:write reg error:reg=300a
  299. camera ov5642 is not found
  300. ov5640_mipi 1-003e: found pwm2, period=45
  301. usb 1-1: new high-speed USB device number 2 using ci_hdrc
  302. update_device_addr: ov5640_mipi ret=-5
  303. ov5640_read_reg(mipi):reg=300a ret=-5
  304. camera ov5640_mipi is not found
  305. usbcore: registered new interface driver uvcvideo
  306. USB Video Class driver (1.1.1)
  307. gspca_main: v2.14.0 registered
  308. imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
  309. device-mapper: uevent: version 1.0.3
  310. device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
  311. Bluetooth: HCI UART driver ver 2.2
  312. Bluetooth: HCI H4 protocol initialized
  313. Bluetooth: HCILL protocol initialized
  314. usbcore: registered new interface driver btusb
  315. hub 1-1:1.0: USB hub found
  316. (stc): chnl_id list empty :4
  317. cpuidle: using governor ladder
  318. cpuidle: using governor menu
  319. sdhci: Secure Digital Host Controller Interface driver
  320. sdhci: Copyright(c) Pierre Ossman
  321. sdhci-pltfm: SDHCI platform and OF driver helper
  322. sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode
  323. mmc1: no vqmmc regulator found
  324. hub 1-1:1.0: 3 ports detected
  325. (stk) : st_kim_start
  326. mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
  327. sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode
  328. mmc2: no vqmmc regulator found
  329. mmc1: card claims to support voltages below the defined range. These will be ignored.
  330. mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
  331. mmc1: new SDIO card at address 0001
  332. wl1271_sdio mmc1:0001:2: legacy platform data not found, trying device tree
  333. mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
  334. sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode
  335. mmc3: no vqmmc regulator found
  336. mmc2: host does not support reading read-only switch. assuming write-enable.
  337. mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
  338. Galcore version 5.0.11.25762
  339. mmc2: new high speed SDHC card at address 0007
  340. mmcblk2: mmc2:0007 SD8GB 7.42 GiB
  341. mmcblk2: p1 p2 p3 < p5 p6 p7 p8 > p4
  342. usb 1-1.2: new low-speed USB device number 3 using ci_hdrc
  343. mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  344. mxc_asrc 2034000.asrc: mxc_asrc registered
  345. mxc_vpu 2040000.vpu: VPU initialized
  346. caam 2100000.caam: Instantiated RNG4 SH0
  347. caam 2100000.caam: Instantiated RNG4 SH1
  348. caam 2100000.caam: device ID = 0x0a160100 (Era 4)
  349. caam 2100000.caam: job rings = 2, qi = 0
  350. (stk) :ldisc_install = 1
  351. (stk) :ldisc installation timeout
  352. caam algorithms registered in /proc/crypto
  353. caam_jr 2101000.jr0: registering rng-caam
  354. input: HID 1241:1177 as /devices/soc0/soc.1/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
  355. hid-generic 0003:1241:1177.0001: input: USB HID v1.10 Mouse [HID 1241:1177] on usb-ci_hdrc.1-1.2/input0
  356. usbcore: registered new interface driver usbhid
  357. usbhid: USB HID core driver
  358. ashmem: initialized
  359. logger: created 256K log 'log_main'
  360. logger: created 256K log 'log_events'
  361. logger: created 256K log 'log_radio'
  362. logger: created 256K log 'log_system'
  363. usbcore: registered new interface driver snd-usb-audio
  364. sgtl5000 0-000a: sgtl5000 revision 0x11
  365. fsl-hdmi-dai hdmi_audio.18: failed to probe. Load HDMI-video first.
  366. fsl-hdmi-dai: probe of hdmi_audio.18 failed with error -12
  367. init_gpio_data:-2
  368. init_gpio_data:-2
  369. sgtl5000 0-000a: Failed to get supply 'VDDD': -19
  370. 0-000a: 1200 mV normal
  371. sgtl5000 0-000a: Using internal LDO instead of VDDD
  372. imx-sgtl5000 sound.26: sgtl5000 <-> 2028000.ssi mapping ok
  373. imx-audio-hdmi sound-hdmi.27: initialize HDMI-audio failed. load HDMI-video first!
  374. NET: Registered protocol family 26
  375. u32 classifier
  376. Actions configured
  377. Netfilter messages via NETLINK v0.30.
  378. nf_conntrack version 0.5.0 (16030 buckets, 64120 max)
  379. ctnetlink v0.93: registering with nfnetlink.
  380. NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  381. NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  382. xt_time: kernel timezone is -0000
  383. ip_tables: (C) 2000-2006 Netfilter Core Team
  384. arp_tables: (C) 2002 David S. Miller
  385. TCP: cubic registered
  386. Initializing XFRM netlink socket
  387. NET: Registered protocol family 10
  388. mip6: Mobile IPv6
  389. ip6_tables: (C) 2000-2006 Netfilter Core Team
  390. NET: Registered protocol family 17
  391. NET: Registered protocol family 15
  392. can: controller area network core (rev 20120528 abi 9)
  393. NET: Registered protocol family 29
  394. can: raw protocol (rev 20120528)
  395. can: broadcast manager protocol (rev 20120528 t)
  396. can: netlink gateway (rev 20130117) max_hops=1
  397. Bluetooth: RFCOMM TTY layer initialized
  398. Bluetooth: RFCOMM socket layer initialized
  399. Bluetooth: RFCOMM ver 1.11
  400. Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  401. Bluetooth: BNEP filters: protocol multicast
  402. Bluetooth: BNEP socket layer initialized
  403. Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  404. Bluetooth: HIDP socket layer initialized
  405. 8021q: 802.1Q VLAN Support v1.8
  406. Key type dns_resolver registered
  407. (stk) :ldisc_install = 0
  408. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  409. Registering SWP/SWPB emulation handler
  410. usb_otg_vbus: disabling
  411. regulator-dummy: disabling
  412. imx mcc test is registered.
  413. file system registered
  414. android_usb gadget: Mass Storage Function, version: 2009/09/11
  415. android_usb gadget: Number of LUNs=1
  416. lun0: LUN: removable file: (no medium)
  417. android_usb gadget: android_usb ready
  418. input: gpio-keys.25 as /devices/soc0/gpio-keys.25/input/input1
  419. rtc-isl1208 0-006f: setting system clock to 2015-07-10 14:57:12 UTC (1436540232)
  420. ALSA device list:
  421. #0: sgtl5000-audio
  422. Freeing unused kernel memory: 300K (80a2a000 - 80a75000)
  423. type=1403 audit(1436540232.740:2): policy loaded auid=4294967295 ses=4294967295
  424. type=1404 audit(1436540232.750:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
  425. (stk) : timed out waiting for ldisc to be un-installed
  426. (stk) :ldisc_install = 1fs_mgr: boot device base == mmcblk2
  427. EXT4-fs (mmcblk2p1): recovery complete
  428. EXT4-fs (mmcblk2p1): mounted filesystem with ordered data mode. Opts: errors=remount-ro
  429. fs_mgr: __mount(source=/dev/block/mmcblk2p1,target=/boot,type=ext4)=0
  430. EXT4-fs (mmcblk2p2): recovery complete
  431. EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: errors=remount-ro
  432. fs_mgr: __mount(source=/dev/block/mmcblk2p2,target=/recovery,type=ext4)=0
  433. EXT4-fs (mmcblk2p5): mounted filesystem with ordered data mode. Opts: (null)
  434. fs_mgr: __mount(source=/dev/block/mmcblk2p5,target=/system,type=ext4)=0
  435. EXT4-fs (mmcblk2p4): Ignoring removed nomblk_io_submit option
  436. (stk) :ldisc installation timeout
  437. (stk) :ldisc_install = 0EXT4-fs (mmcblk2p4): recovery complete
  438. EXT4-fs (mmcblk2p4): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,noauto_da_alloc,errors=panic
  439. fs_mgr: __mount(source=/dev/block/mmcblk2p4,target=/data,type=ext4)=0
  440. EXT4-fs (mmcblk2p6): Ignoring removed nomblk_io_submit option
  441. EXT4-fs (mmcblk2p6): recovery complete
  442. EXT4-fs (mmcblk2p6): mounted filesystem with ordered data mode. Opts: nomblk_io_submit
  443. fs_mgr: __mount(source=/dev/block/mmcblk2p6,target=/cache,type=ext4)=0
  444. EXT4-fs (mmcblk2p7): mounted filesystem with ordered data mode. Opts: (null)
  445. fs_mgr: __mount(source=/dev/block/mmcblk2p7,target=/device,type=ext4)=0
  446. binder: 190:190 transaction failed 29189, size 0-0
  447. init: using deprecated syntax for specifying property 'ro.serialno', use ${name} instead
  448. init: using deprecated syntax for specifying property 'ro.product.manufacturer', use ${name} instead
  449. init: using deprecated syntax for specifying property 'ro.product.model', use ${name} instead
  450. init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
  451. init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
  452. init: cannot find '/system/bin/rild', disabling 'ril-daemon'
  453. android_usb: already disabled
  454. read descriptors
  455. read strings
  456. mtp_bind_config
  457. android_usb gadget: high-speed config #1: android
  458. android_work: sent uevent USB_STATE=CONFIGURED
  459. (stk) : timed out waiting for ldisc to be un-installedroot@nitrogen6x:/ #
  460. (stk) :ldisc_install = 1fs_mgr: boot device base == mmcblk2
  461. (stc): st_tty_open
  462. (stk) :line discipline installed(stk) :ti-connectivity/TIInit_7.6.15.bts
  463. (stk) :change remote baud rate command in firmware(stk) :skipping the wait event of change remote baudhealthd: No charger supplies found
  464. healthd: No battery devices found
  465.  
  466. (stc): add_channel_to_table: id 4
  467. (stc): add_channel_to_table: id 2
  468. (stc): add_channel_to_table: id 3
  469. (stc): remove_channel_from_table: id 3
  470. (stc): remove_channel_from_table: id 2
  471. (stc): remove_channel_from_table: id 4
  472. (stc): all chnl_ids unregistered
  473. (stk) :ldisc_install = 0(stc): st_tty_close request_suspend_state: wakeup (3->0) at 8075176667 (2015-07-10 14:57:16.921230333 UTC)
  474. init: untracked pid 398 killed by signal 9
  475. request_suspend_state: wakeup (0->0) at 10901042334 (2015-07-10 14:57:19.747096000 UTC)
  476. init: untracked pid 481 killed by signal 9
  477. request_suspend_state: wakeup (0->0) at 16757567334 (2015-07-10 14:57:25.603621334 UTC)
  478. init: untracked pid 565 killed by signal 9
  479. request_suspend_state: wakeup (0->0) at 21546503668 (2015-07-10 14:57:30.392557002 UTC)
  480. init: untracked pid 636 exited with status 0
  481. request_suspend_state: wakeup (0->0) at 26471526669 (2015-07-10 14:57:35.317579669 UTC)
  482. init: untracked pid 737 killed by signal 9
  483. request_suspend_state: wakeup (0->0) at 31461586669 (2015-07-10 14:57:40.307640336 UTC)
  484. init: untracked pid 849 killed by signal 9
  485. request_suspend_state: wakeup (0->0) at 36341576337 (2015-07-10 14:57:45.187630670 UTC)
  486. init: untracked pid 942 killed by signal 9
  487. request_suspend_state: wakeup (0->0) at 41211660671 (2015-07-10 14:57:50.057715004 UTC)
  488. init: untracked pid 1031 killed by signal 9
  489. request_suspend_state: wakeup (0->0) at 46061611671 (2015-07-10 14:57:54.907665338 UTC)
  490. init: untracked pid 1113 killed by signal 9
  491. android_work: sent uevent USB_STATE=DISCONNECTED
  492. android_work: did not send uevent (0 0 (null))
  493. request_suspend_state: wakeup (0->0) at 50951563005 (2015-07-10 14:57:59.797616338 UTC)
  494. android_work: did not send uevent (0 0 (null))
  495. init: untracked pid 1221 killed by signal 9
  496. android_work: did not send uevent (0 0 (null))
  497. android_work: did not send uevent (0 0 (null))
  498. android_work: sent uevent USB_STATE=CONNECTED
  499. android_usb gadget: high-speed config #1: android
  500. android_work: sent uevent USB_STATE=CONFIGURED
  501. request_suspend_state: wakeup (0->0) at 56841530673 (2015-07-10 14:58:05.687584339 UTC)
  502. init: untracked pid 1306 killed by signal 9
  503. request_suspend_state: wakeup (0->0) at 61771525340 (2015-07-10 14:58:10.617578673 UTC)
  504. init: untracked pid 1401 killed by signal 9
  505. request_suspend_state: wakeup (0->0) at 66691764340 (2015-07-10 14:58:15.537818007 UTC)
  506. init: untracked pid 1497 killed by signal 9
  507. request_suspend_state: wakeup (0->0) at 71591510674 (2015-07-10 14:58:20.437564674 UTC)
  508. init: untracked pid 1588 killed by signal 9
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!